Polygroup 1701 Remote controller User Manual TG76P4812L02 new

Download:
Mirror Download [FCC.gov]
Document ID	3279957
Application ID	AoBidl9B9mDOjW2sPr6/eA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	92.18kB (1152232 bits)
Date Submitted	2017-02-10 00:00:00
Date Available	2017-02-12 00:00:00
Creation Date	2016-12-19 16:32:08
Producing Software	Adobe PDF library 10.01
Document Lastmod	2017-01-18 14:59:51
Document Title	TG76P4812L02-new
Document Creator	Adobe Illustrator CC (Windows)
Document Author:	eric.costello

ASSEMBLY INSTRUCTIONS
GROW & STOW™
CHRISTMAS TREE
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
o)
SAVE THESE INSTRUCTIONS
MADE IN CHINA
a)
b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit
Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper
installation.
c) This seasonal use product is not intended for permanent installation or use.
d) Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of
heat.
e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire burns, personal injury and electric shock it
should not be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this may damage the wire
insulation.
l) Do not cover the product with cloth, paper or any material not part of the product when in use.
m) This product is equipped with push-in type lamps. Do not twist lamps.
n) Read and follow all instructions that are on the product or provided with the product.
a) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or
frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections or
exposed copper wire.
b) When storing the product, carefully remove the product from wherever it is placed, including trees,
branches, or bushes, to avoid any undue strain or stress on the product conductors, connections,
and wires.
c) When not in use, store neatly in a cool, dry location protected from sunlight.
USER SERVICNG INSTRUCTIONS
Lamp Replacement:
Step 1: Grasp plug
and remove from the
receptacle or other
outlet device. Do not
unplug by pulling on
cord.
Step 2: Lift up to
unsnap locking
tab, then pull lamp
and plastic base
straight out of
lampholder.
Step 3: Replace lamp
with only 3.6 Volt,
0.072 watt or 2.4 Volt,
0.048 Watt LED type
lamps provided with
this product.
(Reference figure only)
If the new lamp base does not fit in lamp holder, follow
the step below before Step 3.
a) Remove the base or burned out lamp by straightening
lamp leads and gently pull lamp out.
b) Thread leads of new lamp through holes in old base
with one lead in each hole.
c) After lamp is fully inserted into base, bend each lead
up, like other lamps in the light set so that the leads
will touch the contacts inside the lampholder.
CAUTION:
1. Risk of fire. This product dose not contain lamp shunts, which allow the product to operate if one
lamp burns out.Replace lamps only with the spare lamps provided wiht this product.
2. To reduce the risk of fire and electric shock: a) Do not install on trees having needles, leaves or
branch coverings of metal or materials which look like metal, and b) Do not mount or support
strings in a manner that can cut or damage wire insulation .
ASSEMBLY INSTRUCTIONS
Use and Care Instructions
PRODUCT SPECIFICATION
Description
Grow and Stow tree is an indoor Christmas Tree provided with a electromechanical system for multiple
height adjustment. Powered by a switching power supply (adaptor), It can be control by a foot pedal and a
RF remote control unit. This controller commands the mechanism for stow and deploy, as well as the
lighting functions. The full lower section of the motorized tree is provided with quick set connectors, and
this entire tree easily storages within a compact bag for convenient storage.
Switching Power Supply (adaptor):
7.5ft Tree Grow Range (Vertical Stroke):
9ft Tree Grow Range (Vertical Stroke):
Input AC110-240V, 50/60Hz, Output DC 29V/2A
Minimum: 6ft
Maximum: 7.5ft
Stroke: 1.5ft
Minimum: 7ft
Maximum 9ft
Stroke: 2ft
Tree Life Cycle:
3000 Cycles Max.
Remote Controller Range:
33 ft (10m)
Remote Controller Power
DC 3V
Operational Temperature:
0 C to 40 C, 85% Humidity, indoor use
Storage Temperature:
-5 C to 60 C, 85% Humidity
Accessories Included:
Foot Pedal, Remote hand set, adaptor, power cord, owner manual
MADE IN CHINA
Drawing
No.
Description
Qty
AC Power Cord
AC/DC Power Adaptor
Adaptor AC input jacks
Adaptor DC output jacks
Tree trunk base
Tree control male 4 pin connector, to foot pedal
Light string male 2 pin connector, to foot pedal
Tree stand with fixed wheels and swiveling casters
Caster locks
10
Tree foliage, lower section
11
Light strings connectors set
12
Quick set guide funnel and female socket
13
Quick set male connector
14
Tree top section
Key
Description
15
Foot Pedal unit
16
Foot pedal - Light Functions Push button
17
Foot pedal - Grow / Pause/ Stow Push button
18
Foot pedal - Safety Lock Switch
19
Foot pedal - 2pin male connector to power adaptor DC jack
20
Foot pedal - 4pin female connector to tree control
21
Foot pedal - 2pin female connector to light string
Key
Description
22
Remote Control handset
23
Remote LED indicator
24
Remote light functions button
25
Remote grow (Up and Pause) button
26
Remote stow (Down and Pause) button
27
Remote battery compartment and lid
Key
Qty
ASSEMBLY INSTRUCTIONS
Grow And Stow Tree Part Table
Qty
Description
Qty
Tree bag - tree head
Tree bag - tree Main
MADE IN CHINA
Tree bag/pouch - Accessories (small)
24
ASSEMBLY INSTRUCTIONS
23
25
26
14
22
27
13
12
11
10
21
16
20
18
17
19
15
MADE IN CHINA
Main Diagram
Unpack Carton box
1.1 Place the tree box on an upright position
(long side along the vertical direction).
See the arrows marked on the box for reference.
1.2 Untie the wrap string around the carton box,
knife or cutter may be required (not included).
1.3 Pull up the top carton cover by the side hole handles
(one on each side of carton box).
1.4 Remove the tree head section out of the box and
open the tree head bag.
1.5 Remove the foam pads under the front wheels of
the stand (swiveling casters Fig 1). The hard board
under the stand will tip down creating a slight slope.
1.6 Pull the tree out of the carton box carefully.
1.7 Unlock the buckles on the tree bag, and loose the
tree bag rope.
1.8 Open the tree bag wide and pull it up from the top
of the tree.
1.1
1.3
1.2
1.4
PULL
1.5
1.6
PULL
Fig 1
HERE
PULL
1.7
HERE
HERE
1.8
Fig 2
Tree Assembly
ASSEMBLY INSTRUCTIONS
SET UP INSTRUCTION
2.1 Open and remove the protective cap from the top of the funnel
guide 12 before inserting the tree top section 14 .
2.2 Inserts the tree top section 14 into top funnel gide 12 of main
section (see Fig 2)
Wire Connection
3.1 All accessories are stored in a small pouch 28 , attached near the tree wheel stand. Open the pouch and
put all accessories ready for use. (all wires display as seen on fig 3)
3.2 Connect the 2pin and 4pin connectors coming from the base of the tree to their counterpart connectors
on the foot pedal (As shown on fig. 3). Make sure to lock them by turning the sockets.
3.3 Plug the pedal 2 pin connector 19 into the DC Power Adaptor output jack 4 .Turn and lock
with the socket.
3.4 Plug the Power adaptor AC cord 1 into an AC outlet.
3.5 The tree is energized and ready to be operated.
Fig 3
MADE IN CHINA
4.1 Double check all connections are properly and securely done 19 20 21
Fig 4
(see fig 3), and make sure the lock switch 18 is on "unlock"
position .
4.2 Push the tree logo button 17 on foot pedal to start toggling between
Grow, Pause, and Stow functions.
4.3 Push the light button 16 on foot pedal to navigate the light string functions.
4.4 Note:
If your foot pedal is 3 flashing mode model, your remote handset can
control light flash with 3 kind modes (clear steady, multi steady , clear
multi alternating )
If your foot pedal is the 8 flashing modes model, your tree will cycle
between 8 flashing modes (clear multi fading, clear fading, clear multi
alternating, steady clear, clear multi slow fading, multi steady , multi fading, and combination )
If your foot pedal is the 10 flashing modes model, your tree will cycle between 10 flashing modes
(clear steady/ clear fading/ multi steady/ multi fading/ clear multi fading/ clear multi alternating /
pastel steady/ pastel fading/ clear pastel multi alternating/ clear pastel multi fading)
4.5 Slide lock switch 18 on foot pedal to function lock or unlock. Grow and stow function is lock for foot
pedal and remote when in "lock" position.
Tree Shaping and Final Touches
5.1 After growing the tree to a desired height, allow all branches to fall into place. Additionally, gently pull
them up and out until in place. For aesthetical purposes, make sure that all branches are tilted down
and unfolded.
5.2 Continue to shape up the branches and tips working form the top down. Start with tips farthest from the
trunk, and move towards the inner ones.
5.3 After shaping the entire tree as previously recommended, slightly upsweep all branch tips for a uniform
look. Shift branches to fill any gaps. Your Christmas tree is now complete and ready to be decorated.
NOTE: It is highly recommended to operate the grow and stow functions ONLY when the tree is free of
any ornament or decoration.
ASSEMBLY INSTRUCTIONS
Tree Operation by Foot Pedal (Fig 4)
Remote Hand Set Batteries Installation
6.1 Remove the battery lid 27 at the back of remote control, install the two
AAA/UM4/LR03 batteries( not included) properly as indicated on the
battery compartment. Make sure to match the (+) and (-) ends of the
batteries . (see fig 5)
6.2 Buttons on the remote handset buttons are non-functional when
the foot pedal lock switch 18 is set to "lock" position. Make sure
the switch is set to "unlock"
position. (see Fig 4)
6.3 Press light mode button 24 to navigate the light functions.
Fig 5
Note:
If your foot pedal is 3 flashing mode model, your remote handset can
control light flash with 3 kind modes (clear steady, multi steady , clear
multi alternating )
If your foot pedal is the 8 flashing modes model, your tree will cycle between 8 flashing modes
(clear multi fading, clear fading, clear multi alternating, steady clear, clear multi slow fading, multi steady,
multi fading, and combination )
If your foot pedal is the 10 flashing modes model, your tree will cycle between 10 flashing modes
(clear steady/ clear fading/ multi steady/ multi fading/ clear multi fading/ clear multi alternating /
pastel steady/ pastel fading/ clear pastel multi alternating/ clear pastel multi fading)
6.4 Press UP button 25 on remote hand set to control tree Grow or Pause functions (toggle).
6.5 Press DOWN button 26 on remote to controls Stow or Pause functions (toggle).
MADE IN CHINA
7.1 IMPORTANT: Remove all ornaments and decorations.
Fig 6
7.2 Set the Grow and Stow tree to its minimum size. (fig 6)
7.3 Detach the AC power cord 1 from AC outlet, and put all accessories
parts into the accessories stow pouch 28 .
7.4 Collect all wires, controllers and accessories inside the stow pouch.
And attach it to the trunk near wheel stand 8 . (Recommended)
7.5 Remove the tree top section 14 from top funnel guide. Fold all
branches towards the pole and stow it inside the tree top bag 29 .
7.6 Gently fold up main section branches if needed.
7.7 Place the main tree bag 30 around the tree main section, warping
the tree from top to bottom. Zip it until fully closed.
7.8 Cinch tight the nylon rope on the bottom side of the main tree bag, the
strap will hold its position once you release the spring clamp.
7.9 Buckle the straps until you hear a firm click. Then cinch the straps tightly by pulling at the end of the
loose strap.
7.10 When not in use, store the tree in a cool, dry place away from sunlight. Exposing the tree to
excessive heat or humidity may damage the tree.
REPLACEMENT PARTS ORDERING INFORMATION
No
DESCRIPTION
Drawing
No.
PART No.
qty
AC power cord
x1
AC/DC adaptor
x1
Rolling wheel tree stand
x1
quick set funnel
12
x1
Tree head section
14
x1
Foot Pedal unit
15
x1
Remote control handset
22
x1
Tree bag - Accessories (small)
28
x1
Tree bag - tree head
29
x1
10
Tree bag - tree Main
30
x1
11
hinge pins and washers
x1
12
LED light bulb
ASSEMBLY INSTRUCTIONS
Storage Instructions
SPARE PARTS ?
hinge pins and washers
LED light bulb
Fig. 7
MADE IN CHINA
WARNING: UNPLUG THE POWER CORD BEFORE TROUBLESHOOTING THE GROW & STOW TREE.
SYMPTOM
No power on
Tree
mechanism
does not
works
Remote
control no
work
No light on
Tree tilts
The tree
6 not complete
up or down
CAUSE
SOLUTION
A. Adaptor is not plugged In
A. Adaptor must be plugged into an AC outlet.
B. Foot pedal wires not connected
B. Foot pedal wire must be plugged into a DC jack of
adaptor, and other wires to tree
C. Low voltage
C. Check line voltage - must be 105 to 240 AC volts.
A. Foot pedal set on "LOCK"
position
A. Set the lock switch to "UNLOCK"
position
B. wires no connected
B. Make sure all wires are properly connected and
A. Batteries out of power
A. Replace a brand new AAA/UM4/LR03 batteries
B. Batteries install wrong polarity
B. Check batteries polarity diagram inside the
C. You may out of effective range
C. Ensure the remote is operated within the range
(10 meters)
A. LED light string connector no
connected
A. Check all connectors of light string (plugs and jacks)
are connected on trunk (see main diagram point 11 )
B. LED light bulb missing or damage
B. Extra LED light bulb are included for replace an spare
LED light bulb
C. Light string cord no connected to
Foot pedal
C. Make sure the light string cord is connected to foot
paddle and lock with ring screw.(see fig.3)
A. Wheel stand set on unflat ground
A. Adjust the whole tree to flat ground surface.
A. Tree branches and Tips make jam
each other
A. Adjust pull the branches and tips up and out direction.
Prevent they cross jam together.
B. remote or foot pedal was pressed
PAUSE function
B. Press the button again on remote or foot pedal to
release PAUSE (see fig. 4)
locked. (see fig.3)
batteries case. (see fig 5)
ASSEMBLY INSTRUCTIONS
TROUBLESHOOTING GUIDE
A. Extra hinge pins are included for repairing the hinges.
Insert a new hinge pin through the hold and secure
using the retainer washer (see fig. 7 )
Loose Hinge
Pin
FCC VERIFICATION USER MANUAL
•
•
•
•
MADE IN CHINA
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used
in portable exposure condition without restriction.
RSS-Gen Issue 4 November 2014"&"CNR-Gen 4e éditionNovember 2014:
- English:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
- French:
Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitationestautorisée aux deux
conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi,
mêmesi le brouillageest susceptible d'encompromettre le fonctionnement.
L'appareil a été évalué pour répondre aux exigences générales en matière
d'exposition aux radiofréquences. Le dispositif peut être utilisé en condition
d'exposition portable sans restriction.
ASSEMBLY INSTRUCTIONS
IC Caution.
MADE IN CHINA

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15
Modify Date                     : 2017:01:18 14:59:51+08:00
Create Date                     : 2016:12:19 16:32:08+09:00
Metadata Date                   : 2017:01:18 14:59:51+08:00
Creator Tool                    : Adobe Illustrator CC (Windows)
Thumbnail Width                 : 24
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 3930 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : TG76P4812L02-new
Creator                         : eric.costello
Document ID                     : xmp.did:46a604a6-f1b5-3f46-a69f-75af975de1c4
Instance ID                     : uuid:a30f9884-efcf-463a-adc8-4c10df02f85b
Rendition Class                 : proof:pdf
Original Document ID            : uuid:b385e1e0-6d2d-4bea-9512-4ee4c9594935
Derived From Instance ID        : uuid:c2179950-a1d2-4d07-bce8-08619fb7d9bc
Derived From Document ID        : xmp.did:6e46ca10-f2c1-e747-b40f-9c72605b8296
Derived From Original Document ID: uuid:b385e1e0-6d2d-4bea-9512-4ee4c9594935
Derived From Rendition Class    : default
History Action                  : saved, saved
History Instance ID             : xmp.iid:34c87c9e-a1d9-0644-8c34-c2925edd23fa, xmp.iid:46a604a6-f1b5-3f46-a69f-75af975de1c4
History When                    : 2016:01:21 15:52:28+08:00, 2016:12:19 16:32+08:00
History Software Agent          : Adobe Illustrator CC (Windows), Adobe Illustrator CC (Windows)
History Changed                 : /, /
Producer                        : Adobe PDF library 10.01
N Pages                         : 1
Has Visible Transparency        : False
Has Visible Overprint           : False
Max Page Size W                 : 209.902433
Max Page Size H                 : 296.999615
Max Page Size Unit              : Millimeters
Font Name                       : ArialMT, Arial-BoldMT, MyriadPro-Regular, Myriad-Roman, Myriad-Bold
Font Family                     : Arial, Arial, Myriad Pro, Myriad, Myriad
Font Face                       : Regular, Bold, Regular, Roman, Bold
Font Type                       : Open Type, Open Type, Open Type, Open Type, TrueType
Font Version                    : Version 5.10, Version 5.08, Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329, 001.000, 001.000
Font Composite                  : False, False, False, False, False
Font File Name                  : arial.ttf, arialbd.ttf, MyriadPro-Regular.otf, Myriad-Roman.otf, Myriad-Bold.ttf
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Groups Group Name        : 默认色板组
Swatch Groups Group Type        : 0
Swatch Groups Colorants Swatch Name: AutoCAD Color 2
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Cyan    : 92.971694
Swatch Groups Colorants Magenta : 87.972838
Swatch Groups Colorants Yellow  : 89.019603
Swatch Groups Colorants Black   : 79.998469
Page Count                      : 9
Author                          : eric.costello

EXIF Metadata provided by EXIF.tools