Polygroup 1701 Remote controller User Manual TG76P4812L02 new
Polygroup Limited(Macao Commercial Offshore) Remote controller TG76P4812L02 new
Contents
- 1. User Manual
- 2. Users Manual
User Manual
ASSEMBLY INSTRUCTIONS GROW & STOW™ CHRISTMAS TREE IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. o) SAVE THESE INSTRUCTIONS MADE IN CHINA a) b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation. c) This seasonal use product is not intended for permanent installation or use. d) Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of heat. e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails. f) Do not let lamps rest on the supply cord or on any wire. g) Unplug the product when leaving the house, when retiring for the night, or if left unattended. h) This is an electric product-not a toy! To avoid risk of fire burns, personal injury and electric shock it should not be played with or placed where small children can reach it. i) Do not use this product for other than its intended use. j) Do not hang ornaments or other objects from cord, wire, or light string. k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation. l) Do not cover the product with cloth, paper or any material not part of the product when in use. m) This product is equipped with push-in type lamps. Do not twist lamps. n) Read and follow all instructions that are on the product or provided with the product. a) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections or exposed copper wire. b) When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires. c) When not in use, store neatly in a cool, dry location protected from sunlight. USER SERVICNG INSTRUCTIONS Lamp Replacement: Step 1: Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord. Step 2: Lift up to unsnap locking tab, then pull lamp and plastic base straight out of lampholder. Step 3: Replace lamp with only 3.6 Volt, 0.072 watt or 2.4 Volt, 0.048 Watt LED type lamps provided with this product. (Reference figure only) If the new lamp base does not fit in lamp holder, follow the step below before Step 3. a) Remove the base or burned out lamp by straightening lamp leads and gently pull lamp out. b) Thread leads of new lamp through holes in old base with one lead in each hole. c) After lamp is fully inserted into base, bend each lead up, like other lamps in the light set so that the leads will touch the contacts inside the lampholder. CAUTION: 1. Risk of fire. This product dose not contain lamp shunts, which allow the product to operate if one lamp burns out.Replace lamps only with the spare lamps provided wiht this product. 2. To reduce the risk of fire and electric shock: a) Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal, and b) Do not mount or support strings in a manner that can cut or damage wire insulation . ASSEMBLY INSTRUCTIONS Use and Care Instructions PRODUCT SPECIFICATION Description Grow and Stow tree is an indoor Christmas Tree provided with a electromechanical system for multiple height adjustment. Powered by a switching power supply (adaptor), It can be control by a foot pedal and a RF remote control unit. This controller commands the mechanism for stow and deploy, as well as the lighting functions. The full lower section of the motorized tree is provided with quick set connectors, and this entire tree easily storages within a compact bag for convenient storage. Switching Power Supply (adaptor): 7.5ft Tree Grow Range (Vertical Stroke): 9ft Tree Grow Range (Vertical Stroke): Input AC110-240V, 50/60Hz, Output DC 29V/2A Minimum: 6ft Maximum: 7.5ft Stroke: 1.5ft Minimum: 7ft Maximum 9ft Stroke: 2ft Tree Life Cycle: 3000 Cycles Max. Remote Controller Range: 33 ft (10m) Remote Controller Power DC 3V Operational Temperature: 0 C to 40 C, 85% Humidity, indoor use Storage Temperature: -5 C to 60 C, 85% Humidity Accessories Included: Foot Pedal, Remote hand set, adaptor, power cord, owner manual MADE IN CHINA Drawing No. Description Qty AC Power Cord AC/DC Power Adaptor Adaptor AC input jacks Adaptor DC output jacks Tree trunk base Tree control male 4 pin connector, to foot pedal Light string male 2 pin connector, to foot pedal Tree stand with fixed wheels and swiveling casters Caster locks 10 Tree foliage, lower section 11 Light strings connectors set 12 Quick set guide funnel and female socket 13 Quick set male connector 14 Tree top section Key Description 15 Foot Pedal unit 16 Foot pedal - Light Functions Push button 17 Foot pedal - Grow / Pause/ Stow Push button 18 Foot pedal - Safety Lock Switch 19 Foot pedal - 2pin male connector to power adaptor DC jack 20 Foot pedal - 4pin female connector to tree control 21 Foot pedal - 2pin female connector to light string Key Description 22 Remote Control handset 23 Remote LED indicator 24 Remote light functions button 25 Remote grow (Up and Pause) button 26 Remote stow (Down and Pause) button 27 Remote battery compartment and lid Key Qty ASSEMBLY INSTRUCTIONS Grow And Stow Tree Part Table Qty Description Qty Tree bag - tree head Tree bag - tree Main MADE IN CHINA Tree bag/pouch - Accessories (small) 24 ASSEMBLY INSTRUCTIONS 23 25 26 14 22 27 13 12 11 10 21 16 20 18 17 19 15 MADE IN CHINA Main Diagram Unpack Carton box 1.1 Place the tree box on an upright position (long side along the vertical direction). See the arrows marked on the box for reference. 1.2 Untie the wrap string around the carton box, knife or cutter may be required (not included). 1.3 Pull up the top carton cover by the side hole handles (one on each side of carton box). 1.4 Remove the tree head section out of the box and open the tree head bag. 1.5 Remove the foam pads under the front wheels of the stand (swiveling casters Fig 1). The hard board under the stand will tip down creating a slight slope. 1.6 Pull the tree out of the carton box carefully. 1.7 Unlock the buckles on the tree bag, and loose the tree bag rope. 1.8 Open the tree bag wide and pull it up from the top of the tree. 1.1 1.3 1.2 1.4 PULL 1.5 1.6 PULL Fig 1 HERE PULL 1.7 HERE HERE 1.8 Fig 2 Tree Assembly ASSEMBLY INSTRUCTIONS SET UP INSTRUCTION 2.1 Open and remove the protective cap from the top of the funnel guide 12 before inserting the tree top section 14 . 2.2 Inserts the tree top section 14 into top funnel gide 12 of main section (see Fig 2) Wire Connection 3.1 All accessories are stored in a small pouch 28 , attached near the tree wheel stand. Open the pouch and put all accessories ready for use. (all wires display as seen on fig 3) 3.2 Connect the 2pin and 4pin connectors coming from the base of the tree to their counterpart connectors on the foot pedal (As shown on fig. 3). Make sure to lock them by turning the sockets. 3.3 Plug the pedal 2 pin connector 19 into the DC Power Adaptor output jack 4 .Turn and lock with the socket. 3.4 Plug the Power adaptor AC cord 1 into an AC outlet. 3.5 The tree is energized and ready to be operated. Fig 3 MADE IN CHINA 4.1 Double check all connections are properly and securely done 19 20 21 Fig 4 (see fig 3), and make sure the lock switch 18 is on "unlock" position . 4.2 Push the tree logo button 17 on foot pedal to start toggling between Grow, Pause, and Stow functions. 4.3 Push the light button 16 on foot pedal to navigate the light string functions. 4.4 Note: If your foot pedal is 3 flashing mode model, your remote handset can control light flash with 3 kind modes (clear steady, multi steady , clear multi alternating ) If your foot pedal is the 8 flashing modes model, your tree will cycle between 8 flashing modes (clear multi fading, clear fading, clear multi alternating, steady clear, clear multi slow fading, multi steady , multi fading, and combination ) If your foot pedal is the 10 flashing modes model, your tree will cycle between 10 flashing modes (clear steady/ clear fading/ multi steady/ multi fading/ clear multi fading/ clear multi alternating / pastel steady/ pastel fading/ clear pastel multi alternating/ clear pastel multi fading) 4.5 Slide lock switch 18 on foot pedal to function lock or unlock. Grow and stow function is lock for foot pedal and remote when in "lock" position. Tree Shaping and Final Touches 5.1 After growing the tree to a desired height, allow all branches to fall into place. Additionally, gently pull them up and out until in place. For aesthetical purposes, make sure that all branches are tilted down and unfolded. 5.2 Continue to shape up the branches and tips working form the top down. Start with tips farthest from the trunk, and move towards the inner ones. 5.3 After shaping the entire tree as previously recommended, slightly upsweep all branch tips for a uniform look. Shift branches to fill any gaps. Your Christmas tree is now complete and ready to be decorated. NOTE: It is highly recommended to operate the grow and stow functions ONLY when the tree is free of any ornament or decoration. ASSEMBLY INSTRUCTIONS Tree Operation by Foot Pedal (Fig 4) Remote Hand Set Batteries Installation 6.1 Remove the battery lid 27 at the back of remote control, install the two AAA/UM4/LR03 batteries( not included) properly as indicated on the battery compartment. Make sure to match the (+) and (-) ends of the batteries . (see fig 5) 6.2 Buttons on the remote handset buttons are non-functional when the foot pedal lock switch 18 is set to "lock" position. Make sure the switch is set to "unlock" position. (see Fig 4) 6.3 Press light mode button 24 to navigate the light functions. Fig 5 Note: If your foot pedal is 3 flashing mode model, your remote handset can control light flash with 3 kind modes (clear steady, multi steady , clear multi alternating ) If your foot pedal is the 8 flashing modes model, your tree will cycle between 8 flashing modes (clear multi fading, clear fading, clear multi alternating, steady clear, clear multi slow fading, multi steady, multi fading, and combination ) If your foot pedal is the 10 flashing modes model, your tree will cycle between 10 flashing modes (clear steady/ clear fading/ multi steady/ multi fading/ clear multi fading/ clear multi alternating / pastel steady/ pastel fading/ clear pastel multi alternating/ clear pastel multi fading) 6.4 Press UP button 25 on remote hand set to control tree Grow or Pause functions (toggle). 6.5 Press DOWN button 26 on remote to controls Stow or Pause functions (toggle). MADE IN CHINA 7.1 IMPORTANT: Remove all ornaments and decorations. Fig 6 7.2 Set the Grow and Stow tree to its minimum size. (fig 6) 7.3 Detach the AC power cord 1 from AC outlet, and put all accessories parts into the accessories stow pouch 28 . 7.4 Collect all wires, controllers and accessories inside the stow pouch. And attach it to the trunk near wheel stand 8 . (Recommended) 7.5 Remove the tree top section 14 from top funnel guide. Fold all branches towards the pole and stow it inside the tree top bag 29 . 7.6 Gently fold up main section branches if needed. 7.7 Place the main tree bag 30 around the tree main section, warping the tree from top to bottom. Zip it until fully closed. 7.8 Cinch tight the nylon rope on the bottom side of the main tree bag, the strap will hold its position once you release the spring clamp. 7.9 Buckle the straps until you hear a firm click. Then cinch the straps tightly by pulling at the end of the loose strap. 7.10 When not in use, store the tree in a cool, dry place away from sunlight. Exposing the tree to excessive heat or humidity may damage the tree. REPLACEMENT PARTS ORDERING INFORMATION No DESCRIPTION Drawing No. PART No. qty AC power cord x1 AC/DC adaptor x1 Rolling wheel tree stand x1 quick set funnel 12 x1 Tree head section 14 x1 Foot Pedal unit 15 x1 Remote control handset 22 x1 Tree bag - Accessories (small) 28 x1 Tree bag - tree head 29 x1 10 Tree bag - tree Main 30 x1 11 hinge pins and washers x1 12 LED light bulb ASSEMBLY INSTRUCTIONS Storage Instructions SPARE PARTS ? hinge pins and washers LED light bulb Fig. 7 MADE IN CHINA WARNING: UNPLUG THE POWER CORD BEFORE TROUBLESHOOTING THE GROW & STOW TREE. SYMPTOM No power on Tree mechanism does not works Remote control no work No light on Tree tilts The tree 6 not complete up or down CAUSE SOLUTION A. Adaptor is not plugged In A. Adaptor must be plugged into an AC outlet. B. Foot pedal wires not connected B. Foot pedal wire must be plugged into a DC jack of adaptor, and other wires to tree C. Low voltage C. Check line voltage - must be 105 to 240 AC volts. A. Foot pedal set on "LOCK" position A. Set the lock switch to "UNLOCK" position B. wires no connected B. Make sure all wires are properly connected and A. Batteries out of power A. Replace a brand new AAA/UM4/LR03 batteries B. Batteries install wrong polarity B. Check batteries polarity diagram inside the C. You may out of effective range C. Ensure the remote is operated within the range (10 meters) A. LED light string connector no connected A. Check all connectors of light string (plugs and jacks) are connected on trunk (see main diagram point 11 ) B. LED light bulb missing or damage B. Extra LED light bulb are included for replace an spare LED light bulb C. Light string cord no connected to Foot pedal C. Make sure the light string cord is connected to foot paddle and lock with ring screw.(see fig.3) A. Wheel stand set on unflat ground A. Adjust the whole tree to flat ground surface. A. Tree branches and Tips make jam each other A. Adjust pull the branches and tips up and out direction. Prevent they cross jam together. B. remote or foot pedal was pressed PAUSE function B. Press the button again on remote or foot pedal to release PAUSE (see fig. 4) locked. (see fig.3) batteries case. (see fig 5) ASSEMBLY INSTRUCTIONS TROUBLESHOOTING GUIDE A. Extra hinge pins are included for repairing the hinges. Insert a new hinge pin through the hold and secure using the retainer washer (see fig. 7 ) Loose Hinge Pin FCC VERIFICATION USER MANUAL • • • • MADE IN CHINA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. RSS-Gen Issue 4 November 2014"&"CNR-Gen 4e éditionNovember 2014: - English: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. - French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnement. L'appareil a été évalué pour répondre aux exigences générales en matière d'exposition aux radiofréquences. Le dispositif peut être utilisé en condition d'exposition portable sans restriction. ASSEMBLY INSTRUCTIONS IC Caution. MADE IN CHINA
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15 Modify Date : 2017:01:18 14:59:51+08:00 Create Date : 2016:12:19 16:32:08+09:00 Metadata Date : 2017:01:18 14:59:51+08:00 Creator Tool : Adobe Illustrator CC (Windows) Thumbnail Width : 24 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 3930 bytes, use -b option to extract) Format : application/pdf Title : TG76P4812L02-new Creator : eric.costello Document ID : xmp.did:46a604a6-f1b5-3f46-a69f-75af975de1c4 Instance ID : uuid:a30f9884-efcf-463a-adc8-4c10df02f85b Rendition Class : proof:pdf Original Document ID : uuid:b385e1e0-6d2d-4bea-9512-4ee4c9594935 Derived From Instance ID : uuid:c2179950-a1d2-4d07-bce8-08619fb7d9bc Derived From Document ID : xmp.did:6e46ca10-f2c1-e747-b40f-9c72605b8296 Derived From Original Document ID: uuid:b385e1e0-6d2d-4bea-9512-4ee4c9594935 Derived From Rendition Class : default History Action : saved, saved History Instance ID : xmp.iid:34c87c9e-a1d9-0644-8c34-c2925edd23fa, xmp.iid:46a604a6-f1b5-3f46-a69f-75af975de1c4 History When : 2016:01:21 15:52:28+08:00, 2016:12:19 16:32+08:00 History Software Agent : Adobe Illustrator CC (Windows), Adobe Illustrator CC (Windows) History Changed : /, / Producer : Adobe PDF library 10.01 N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 209.902433 Max Page Size H : 296.999615 Max Page Size Unit : Millimeters Font Name : ArialMT, Arial-BoldMT, MyriadPro-Regular, Myriad-Roman, Myriad-Bold Font Family : Arial, Arial, Myriad Pro, Myriad, Myriad Font Face : Regular, Bold, Regular, Roman, Bold Font Type : Open Type, Open Type, Open Type, Open Type, TrueType Font Version : Version 5.10, Version 5.08, Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329, 001.000, 001.000 Font Composite : False, False, False, False, False Font File Name : arial.ttf, arialbd.ttf, MyriadPro-Regular.otf, Myriad-Roman.otf, Myriad-Bold.ttf Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : 默认色板组 Swatch Groups Group Type : 0 Swatch Groups Colorants Swatch Name: AutoCAD Color 2 Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Tint : 100.000000 Swatch Groups Colorants Mode : CMYK Swatch Groups Colorants Cyan : 92.971694 Swatch Groups Colorants Magenta : 87.972838 Swatch Groups Colorants Yellow : 89.019603 Swatch Groups Colorants Black : 79.998469 Page Count : 9 Author : eric.costelloEXIF Metadata provided by EXIF.tools