Powertech Co R9P007 Wireless Home Appliance Timer Remote Control Kit User Manual RF bester

Powertech Industrial Co Ltd Wireless Home Appliance Timer Remote Control Kit RF bester

Users Manual

Wireless Home Appliance Timer Remote Control KitR9P-120R9P-121R9P-007R9P-202R9P-403R9P-616User’s ManualAll VersionsService Center in USACompany’s name: Haowell Technology & Consulting, Inc.Address: 415 Cloverdale Ln. Walnut, CA 91789-2028phone no: 909-859-5150Fax no: 909-468-4660Contact person: Shannon ChangE-mail: Shannon@HaowellConsultants.com© Copyright 2010The information contained herein is subject to change without notice.This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent.February 2010Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:＊Reorient or relocate the receiving antenna.＊Increase the separation between the equipment and receiver.＊Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.＊Consult the dealer or an experienced radio/TV technician for help.
Operating Instruction - Outlet Adaptor1. Plug the outlet adaptor into a powered 125VAC wall outlet.2. Plug the fixture / appliances you wish to control into 1 outlet wall tap / wall tap plus or the remote outlet of the 2-outlets wall tap plus or yard stake.3. Turn the mechanical power switch (electrical power switch is not applicable) of the fixture / appliance to the ON position.4. Use the timer remote control to set timer and control the fixture/appliance (see the operating instruction – timer remote control in below).IMPORTANT: ● Outdoor use outlet adaptor is recommended plugged into a GFCI-protected outlet.● Outdoor use outlet adaptor is suitable for damp locations. Not for water i mmersion or for use where directly exposed to water.● Yard stake outlet adaptor should be installed above ground level so it will not fill up with water when raining or snowing. Always unplug and remove the devices from the yard stake when raining or snowing. MANUAL ON/OFF AND LEARNING FUNCTION OF THE OUTLET ADAPTER Note: This button on the outlet adapter serves as manual ON/OFF and Learning functions.Manual ON/OFF functionIf you have lost your remote timer control, you can still manually turn on/off the remote outlet on the outlet adaptor.1. To manually turn on the fixture/appliance, press the MANUAL ON/OFF button on the outlet adaptor once. The red LED indicator of the outlet adaptor and the fixture / appliance that plug in the outlet adapter will then turn ON as well.INTRODUCTIONTHANK YOU for purchasing Wireless Home Appliance Timer Remote Control Kit, you can remotely control indoor or outdoor fixtures and appliances from up to 100ft away (in open space).Having your holiday lighting or appliances turned ON & OFF is just as easy as few clicks on the timer remote control. Our product can conveniently help to change your house into an easy home automation style.OPERATING INSTRUCTIONSNOTE: There are five types of Wireless Home Appliance Timer Remote Control Kit available that best suits your needs. The timer remote control and outlet adaptor may vary depending on the kit model purchased.Indoor UseR9P-1201-Outlet Wall Tap with timer remote control1-Outlet Wall Tap Plus with timer remote control2-Outlets Wall Tap Plus (1 always on / 1 remote outlet) with timer remote control4-Outlets Yard Stake(2 always on / 2 remote outlets) with timerremote control6-Outlets Yard Stake(2 always on / 4 remote outlets) with timer remote controlR9P-121 R9P-202 R9P-403 R9P-616Outdoor UseVersions V1.02Versions V1.01
2. To manually turn off the fixture/appliance, press once the MANUAL ON/OFF button on the outlet adaptor. The red LED indicator of the outlet adaptor and the fixture/appliance that plug in the outlet adapter will then turn ON as well.Learning function – for timer remote control and outlet adaptorNOTE: The timer remote control and the outlet adaptor in the kit are pre-paired and ready to use.If you purchase solely outlet adaptor (must be one of above model), you can pair the exiting timer remote control with the new purchase outlet adaptor.1. Hold the timer remote control close to the outlet adaptor.2. Press the learning button (manual ON/OFF button) on the outlet adaptor at least 5 seconds until the red LED indicator light flashes and goes into learning mode, then release the button. 3. Within 15 seconds, press both ON and OFF buttons on the timer remote control once to sync with the outlet adaptor.4. If the outlet adaptor has successfully learned the code from the timer remote control, the red LED indicator will go from flashing light to solid light, then off afterward.5. Check to see if learning is successful by pressing on and off buttons on the timer remote control to switch ON and OFF the outlet adaptor.6. Repeat steps 2~5 if learning is not successful.Operating Instruction – Timer Remote ControlIn open space, the timer remote control has a wireless range up to 100 feet* to control the outlet adaptor.*Actual range may vary depending on environment condition, interference and building materials.To turn ON and OFF the fixture/appliance1. To turn ON the lighting fixture/appliance, press ON button on the remote timer control. The red LED indicator on the timer remote control will flash and the fixture/appliance on the outlet adaptor will turn ON.2. To turn OFF the fixture/appliance, press OFF button on the timer remote control. The red LED indicator on the timer remote control will flash and the fixture/appliance on the outlet adaptor will turn OFF.To turn ON and OFF the fixture/appliance by Timer Feature Example 1: When the fixture/appliance is initially turned ON, and you wish to turn it OFF after 3 hrs.1. Set 3 hrs timer by pressing 3H button on the remote.2. The red LED indicator on the outlet adaptor will flash 3 times to confirm the timer.3. The lighting fixture/appliance will be turned OFF automatically when 3 hrs timer is up.Example 2: When the lighting fixture/appliance is initially turned OFF, and you wish to turn it ON after 6 hrs.1. Set 6 hrs timer by pressing 6H button on the remote.2. The red LED indicator on the outlet adaptor will flash 6 times to confirm the timer.3. The Lighting fixture/appliance will be turned ON automatically when 6 hrs timer is up.Replace battery in the remote timer controlOne A23 12V Alkaline battery is included and pre-installed in the timer remote control.Versions V1.03Versions V1.04
Replace the battery when the red LED light on the timer remote control goes very dim or does not illuminate while operating.Remove the battery compartment cover on the back of the timer remote control, take out the old battery and insert one A23 12V Alkaline battery in the proper orientation, and re-install the battery compartment cover.Wall mount for timer remote control1. Select a spot within the wireless range to mount the supplied wall bracket for timer remote control.2. The ideal locations for wall mount are entrance of a room or location where timer remote control wall mount can be easily seen and accessed.3. Use adhesive tape or supplied screws to securely attach the supplied wall bracket to a wall.SPECIFICATIONSVersions V1.05Versions V1.06Outdoor Use - Wall Tap Plus1. Power on indicator2. Remote OutletIndoor Use - Wall Tap1. Power on indicator2. Manual ON/OFF & Learning Button3. Remote OutletElectrical RatingResistive LoadRemote OutletPower on indicatorStand-by power15A / 125V, 60Hz1875W1Red LED<1WElectrical RatingResistive LoadRemote OutletPower on indicatorStand-by power13A / 125V, 60Hz1625W1Red LED<1WTimer Remote Control1. Power on and timer indicator2. ON/OFF Button – press to control remote outlet or press both ON & OFF buttons to sync with the outlet adaptor3. Timer Setting Buttons – Select timer to control remote outletBattery TypeBattery LifePower on indicatorWireless RangeUse ONLY A23 12V Alkaline3-6 monthsRed LEDUp to 100ft (Open Space)Model No. R9P007 Model No. R9P116T0Model No. R9P115T0
Versions V1.07Outdoor Use – 4 outlet Yard Stake1. Manual ON/OFF & Learning Button2. Power on indicator3. Remote outlets on both side4. Always On outlets on both sideElectrical RatingResistive LoadRemote OutletAlways On outletPower on indicatorStand-by power15A / 125V, 60Hz1875W22Red LED<1WOutdoor Use – 2 outlet Wall Tap Plus1. Power on indicator2. Manual ON/OFF & Learning Button3. Always On outlet4. Remote outletElectrical RatingResistive LoadRemote OutletPower on indicatorStand-by power13A / 125V, 60Hz1625W1Red LED<1WVersions V1.08Model No. R9P204T0Model No. R9P401T0
Versions V1.09Outdoor Use – 6 Outlet Yard Stake1. Manual ON/OFF & Learning Button2. Power on indicator3. Remote outlets on both side4. Always On outlets on both sideElectrical RatingResistive LoadRemote OutletAlways On outletPower on indicatorStand-by power15A / 125V, 60Hz1875W42Red LED<1WModel No. R9P601T0This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu