Powertech Co R9P007 Wireless Home Appliance Timer Remote Control Kit User Manual RF bester
Powertech Industrial Co Ltd Wireless Home Appliance Timer Remote Control Kit RF bester
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1258621 |
| Application ID | Mv5XvcONOLQsIg3iZpLceg== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 28.27kB (353391 bits) |
| Date Submitted | 2010-03-29 00:00:00 |
| Date Available | 2010-03-29 00:00:00 |
| Creation Date | 2009-12-31 12:01:20 |
| Producing Software | Adobe PDF library 8.00 |
| Document Lastmod | 2010-03-23 17:21:56 |
| Document Title | RF bester |
| Document Creator | Adobe Illustrator CS3 |
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ＊Reorient or relocate the receiving antenna. ＊Increase the separation between the equipment and receiver. ＊Connect the equipment into an outlet on a circuit different from that to which the receiver is needed. ＊Consult the dealer or an experienced radio/TV technician for help. Service Center in USA Company’s name: Haowell Technology & Consulting, Inc. Address: 415 Cloverdale Ln. Walnut, CA 91789-2028 phone no: 909-859-5150 Fax no: 909-468-4660 Contact person: Shannon Chang E-mail: Shannon@HaowellConsultants.com © Copyright 2010 Wireless Home Appliance Timer Remote Control Kit R9P-007 R9P-120 R9P-121 R9P-202 R9P-403 R9P-616 User’s Manual The information contained herein is subject to change without notice. This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent. February 2010 All Versions INTRODUCTION Operating Instruction - Outlet Adaptor THANK YOU for purchasing Wireless Home Appliance Timer Remote Control Kit, you can remotely control indoor or outdoor fixtures and appliances from up to 100ft away (in open space). 1. Plug the outlet adaptor into a powered 125VAC wall outlet. 2. Plug the fixture / appliances you wish to control into 1 outlet wall tap / wall tap plus or the remote outlet of the 2-outlets wall tap plus or yard stake. 3. Turn the mechanical power switch (electrical power switch is not applicable) of the fixture / appliance to the ON position. 4. Use the timer remote control to set timer and control the fixture/appliance (see the operating instruction – timer remote control in below). Having your holiday lighting or appliances turned ON & OFF is just as easy as few clicks on the timer remote control. Our product can conveniently help to change your house into an easy home automation style. OPERATING INSTRUCTIONS NOTE: There are five types of Wireless Home Appliance Timer Remote Control Kit available that best suits your needs. The timer remote control and outlet adaptor may vary depending on the kit model purchased. Indoor Use R9P-120 Outdoor Use R9P-121 R9P-202 R9P-403 R9P-616 IMPORTANT: ● Outdoor use outlet adaptor is recommended plugged into a GFCI-protected outlet. ● Outdoor use outlet adaptor is suitable for damp locations. Not for water i mmersion or for use where directly exposed to water. ● Yard stake outlet adaptor should be installed above ground level so it will not fill up with water when raining or snowing. Always unplug and remove the devices from the yard stake when raining or snowing. MANUAL ON/OFF AND LEARNING FUNCTION OF THE OUTLET ADAPTER Note: This button on the outlet adapter serves as manual ON/OFF and Learning functions. Manual ON/OFF function If you have lost your remote timer control, you can still manually turn on/off the remote outlet on the outlet adaptor. 1-Outlet Wall Tap with timer remote control Versions V1.0 1-Outlet Wall Tap Plus with timer remote control 2-Outlets Wall Tap Plus (1 always on / 1 remote outlet) with timer remote control 4-Outlets Yard Stake (2 always on / 2 remote outlets) with timer remote control 6-Outlets Yard Stake (2 always on / 4 remote outlets) with timer remote control 1. To manually turn on the fixture/appliance, press the MANUAL ON/OFF button on the outlet adaptor once. The red LED indicator of the outlet adaptor and the fixture / appliance that plug in the outlet adapter will then turn ON as well. Versions V1.0 2. To manually turn off the fixture/appliance, press once the MANUAL ON/OFF button on the outlet adaptor. The red LED indicator of the outlet adaptor and the fixture/appliance that plug in the outlet adapter will then turn ON as well. Learning function – for timer remote control and outlet adaptor NOTE: The timer remote control and the outlet adaptor in the kit are pre-paired and ready to use. To turn ON and OFF the fixture/appliance 1. To turn ON the lighting fixture/appliance, press ON button on the remote timer control. The red LED indicator on the timer remote control will flash and the fixture/appliance on the outlet adaptor will turn ON. 2. To turn OFF the fixture/appliance, press OFF button on the timer remote control. The red LED indicator on the timer remote control will flash and the fixture/appliance on the outlet adaptor will turn OFF. To turn ON and OFF the fixture/appliance by Timer Feature If you purchase solely outlet adaptor (must be one of above model), you can pair the exiting timer remote control with the new purchase outlet adaptor. 1. Hold the timer remote control close to the outlet adaptor. 2. Press the learning button (manual ON/OFF button) on the outlet adaptor at least 5 seconds until the red LED indicator light flashes and goes into learning mode, then release the button. 3. Within 15 seconds, press both ON and OFF buttons on the timer remote control once to sync with the outlet adaptor. 4. If the outlet adaptor has successfully learned the code from the timer remote control, the red LED indicator will go from flashing light to solid light, then off afterward. 5. Check to see if learning is successful by pressing on and off buttons on the timer remote control to switch ON and OFF the outlet adaptor. 6. Repeat steps 2~5 if learning is not successful. Operating Instruction – Timer Remote Control Example 1: When the fixture/appliance is initially turned ON, and you wish to turn it OFF after 3 hrs. 1. Set 3 hrs timer by pressing 3H button on the remote. 2. The red LED indicator on the outlet adaptor will flash 3 times to confirm the timer. 3. The lighting fixture/appliance will be turned OFF automatically when 3 hrs timer is up. Example 2: When the lighting fixture/appliance is initially turned OFF, and you wish to turn it ON after 6 hrs. 1. Set 6 hrs timer by pressing 6H button on the remote. 2. The red LED indicator on the outlet adaptor will flash 6 times to confirm the timer. 3. The Lighting fixture/appliance will be turned ON automatically when 6 hrs timer is up. In open space, the timer remote control has a wireless range up to 100 feet* to control the outlet adaptor. Replace battery in the remote timer control *Actual range may vary depending on environment condition, interference and building materials. One A23 12V Alkaline battery is included and pre-installed in the timer remote control. Versions V1.0 Versions V1.0 Replace the battery when the red LED light on the timer remote control goes very dim or does not illuminate while operating. Indoor Use - Wall Tap 1. Power on indicator Remove the battery compartment cover on the back of the timer remote control, take out the old battery and insert one A23 12V Alkaline battery in the proper orientation, and re-install the battery compartment cover. 2. Manual ON/OFF & Learning Button 3. Remote Outlet Wall mount for timer remote control 1. Select a spot within the wireless range to mount the supplied wall bracket for timer remote control. 2. The ideal locations for wall mount are entrance of a room or location where timer remote control wall mount can be easily seen and accessed. 3. Use adhesive tape or supplied screws to securely attach the supplied wall bracket to a wall. Model No. R9P115T0 Electrical Rating 15A / 125V, 60Hz Resistive Load 1875W Remote Outlet Power on indicator Red LED Stand-by power <1W SPECIFICATIONS Timer Remote Control 1. Power on and timer indicator 2. ON/OFF Button – press to control remote outlet or press both ON & OFF buttons to sync with the outlet adaptor 1. Power on indicator 3. Timer Setting Buttons – Select timer to control 2. Remote Outlet remote outlet Model No. R9P116T0 Model No. R9P007 Outdoor Use - Wall Tap Plus Battery Type Use ONLY A23 12V Alkaline Electrical Rating 13A / 125V, 60Hz Battery Life 3-6 months Resistive Load 1625W Power on indicator Red LED Remote Outlet Wireless Range Up to 100ft (Open Space) Power on indicator Red LED Stand-by power <1W Versions V1.0 Versions V1.0 Outdoor Use – 2 outlet Wall Tap Plus 1. Power on indicator 2. Manual ON/OFF & Learning Button 3. Always On outlet 4. Remote outlet 1. Manual ON/OFF & Learning Button Outdoor Use – 4 outlet Yard Stake 2. Power on indicator 3. Remote outlets on both side 4. Always On outlets on both side Model No. R9P204T0 Electrical Rating 13A / 125V, 60Hz Resistive Load 1625W Remote Outlet Power on indicator Red LED Stand-by power <1W Model No. R9P401T0 Versions V1.0 Electrical Rating 15A / 125V, 60Hz Resistive Load 1875W Remote Outlet Always On outlet Power on indicator Red LED Stand-by power <1W Versions V1.0 Outdoor Use – 6 Outlet Yard Stake 1. Manual ON/OFF & Learning Button 2. Power on indicator 3. Remote outlets on both side 4. Always On outlets on both side Model No. R9P601T0 Electrical Rating 15A / 125V, 60Hz Resistive Load 1875W Remote Outlet Always On outlet Power on indicator Red LED Stand-by power <1W Versions V1.0 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.1-c036 46.277092, Fri Feb 23 2007 14:16:18 Format : application/pdf Title : RF bester Creator Tool : Adobe Illustrator CS3 Create Date : 2009:12:31 12:01:20+08:00 Modify Date : 2010:03:23 17:21:56+08:00 Metadata Date : 2010:03:23 17:21:56+08:00 Thumbnail Width : 256 Thumbnail Height : 184 Thumbnail Format : JPEG Thumbnail Image : (Binary data 11199 bytes, use -b option to extract) Document ID : uuid:0073AB8696F7DE119387CCE19C702E91 Instance ID : uuid:92d01c94-248c-ee41-820a-aa4be2dad581 Derived From Instance ID : uuid:ad5e059b-c913-344a-94f4-23cf5b5f976b Derived From Document ID : uuid:0F94E1E02CF6DE11813884E08B4FFA82 Startup Profile : Basic CMYK N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 210.000145 Max Page Size H : 148.500044 Max Page Size Unit : Millimeters Font Name : DINOT-Bold, DIN-Regular, DIN-Bold, AdobeMingStd-Light Font Family : DINOT, DIN, DIN, Adobe 明體 Std Font Face : Bold, Regular, Bold, L Font Type : Open Type, Type 1, Type 1, Open Type Font Version : Version 7.460;PS 7.046;hotconv 1.0.38, 001.000, 001.000, Version 5.003;PS 5;hotconv 1.0.49;makeotf.lib2.0.14802 Font Composite : False, False, False, False Font File Name : DINOT Bold.otf, DINReg; DIN-Regular, DINBol; DIN-Bold, AdobeMingStd-Light.otf Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : Default Swatch Group Swatch Group Type : 0 Producer : Adobe PDF library 8.00 Has XFA : No Page Count : 6 Creator Version : 13 Container Version : 11 Creator : Adobe Illustrator(R) 13.0 For : olivea, Bounding Box : 0 0 596 421 Image Height : 421 Image Width : 596 Image Size : 596x421 Megapixels : 0.251EXIF Metadata provided by EXIF.tools