Precise Biometrics MS010013 USB Fingerprint Reader Security System User Manual Quick Setup Manual

Download:
Mirror Download [FCC.gov]
Document ID	142422
Application ID	H+dsq7qqNDec6Dv6tARo4w==
Document Description	Quick Setup Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	35.69kB (446093 bits)
Date Submitted	2001-03-29 00:00:00
Date Available	2001-03-29 00:00:00
Creation Date	2000-10-05 10:10:58
Producing Software	Acrobat Distiller 4.0 for Macintosh
Document Lastmod	2000-10-05 10:11:28
Document Title	Quick Setup Manual

Logging on Using
a Fingerprint
1. If you have a Precise 100 SC Reader, insert your
smart card into the reader and place your finger on
the reader. If you have a Precise 100 A Reader,
simply place your finger on the reader. You can also
press the Enter key and then enter your Username.
2. Place your primary logon finger on the fingerprint
reader sensor. The Verify Fingerprint screen will appear.
3. Keep your finger placed on the
sensor as long as the yellow
light is flashing. The system
verifies your fingerprint and
access rights for the selected
domain.
If verification fails, make sure:
●
your username and domain are correct
●
you place the selected finger on the centre of the sensor
Correct Finger
Placement
Most of the information in a fingerprint is located in the middle of the finger pad.
Therefore, it is important that the middle of the finger pad is placed in the sensor
centre at enrolment and logon.
●
●
●
Quick Reference
Do not “roll” your finger pad. Just press it flat to the sensor.
Place the centre of your finger pad in the sensor centre.
Use medium pressure and avoid rotating your finger.
Perfectly placed finger.
Good image:
fingerprint in
the middle,
medium pressure
to the sensor.
Precise 100 Client for
Windows NT/2000
© Precise Biometrics AB, 2000
info@precisebiometrics.com
www.precisebiometrics.com
Telephone
Sweden: +46-46-311 100
United States: +1-703-848 9266
To get more experience in logging on with your fingerprint, refer to the Precise Demo.
Access the Precise Demo by clicking Start > Programs > Precise Biometrics > Demo.
Precise 100 SC
Precise 100 A
All rights reserved. Second Edition September 2000
P/N: AM010013 R2A
For more information on the Precise 100 system,
please refer to the User’s Manual located on the software CD.
Installation
Connect the fingerprint reader
If you have a Precise 100 Reader with USB connector, skip this sectionand go to the next
page “Log on as an administrator”. If you have a Precise 100 Reader with parallel port
connector, follow the instructions below.
Log on as an administrator
You must have administrator rights on your local computer to install the
Precise 100 Client software.
Install software
Insert the Precise 100 Client software CD. The Master Setup screen will appear.
1. Make sure that the computer has been turned off.
2. Connect the fingerprint reader to the computer as shown below.
To install the Smart Card Base Components
a) Click the SC Base Components button, a submenu appears.
b) Click the Base Components button in the submenu.
c) Click the Update button in the submenu and follow the instructions
3. To install the Precise 100 Client software, click the Precise 100 Client button and
follow the instructions.
4. Restart the computer.
parallel port connector
pass-through
PS/2 connector
keyboard
PS/2 connector
NOTE: The parallel port must be set to ECP
mode, otherwise the fingerprint reader will not
function properly. Please refer to the computer
manual for additional information, or follow the
instructions below.
Enrolling a User
NOTE: If the CD does not start automatically, start
the CD from the desktop by double-clicking My
Computer > CD > MasterSetup.exe icon.
To set the parallel port:
1. Access the system setup utility on your computer. On most computers this is done
by pressing the F1, F10, Delete or Esc key during system booting, i.e. immediately
after switching on the computer.
1. If you have a Precise 100 Reader with USB connector, please connect it to your PC
now. Windows 2000 will detect the new hardware and install the necessary drivers
from the CD. If you have a Precise 100 Reader with parallel port connector, click the
Parallel Driver button to install the necessary parallel port drivers.
2. Find the parallel port mode and set it for ECP. If the ECP selection is unavailable,
the parallel port is probably already set for ECP.
2. If you are using Windows NT you must install the Microsoft Smartcard Base
Components, if not previously installed. If you are using Windows 2000 do not
install the Smartcard Base Components, the system may crash.
3. Save your changes and exit the system setup utility.
NOTE: To be able to log into a domain server account, the user has to be enrolled on the domain server. If the
user is enrolled on a local computer, he or she can only log into that computer using a fingerprint.
1. Log on as an administrator.
2. Click Start > Programs > Precise Biometrics > BioManager.
The BioManager screen will appear.
4. Enter the desired information in the Username, Full Name and Description field.
If you have a Precise 100 SC Reader, you can choose to store the data on the
smart card. Click Next. The Reading Fingerprints screen will appear.
5. Select the fingerprint to be registered by clicking
in one of the checkboxes.
6. Follow the instructions on the screen. To ensure
a good image, make sure the centre of the finger
pad is placed in the sensor centre. The fingerprint
is read four times, for the system to select and
verify a good print.
7. Register another fingerprint, or click Next. The
Logon Information screen will appear.
8. Select primary logon finger. The primary logon
finger is the default finger that will be used to log
into the system.
NOTE: If a current password user is enrolled, the current password is
no longer valid. A new password must be typed, in order for the user to log on with a password.
3. Click User > New User. The User Information screen
of the Fingerprint Enrolment wizard will appear.
9. Click Next. The saving screen will appear.
10. Click Finish to store the data.
Installation
Connect the fingerprint reader
If you have a Precise 100 Reader with USB connector, skip this sectionand go to the next
page “Log on as an administrator”. If you have a Precise 100 Reader with parallel port
connector, follow the instructions below.
Log on as an administrator
You must have administrator rights on your local computer to install the
Precise 100 Client software.
Install software
Insert the Precise 100 Client software CD. The Master Setup screen will appear.
1. Make sure that the computer has been turned off.
2. Connect the fingerprint reader to the computer as shown below.
To install the Smart Card Base Components
a) Click the SC Base Components button, a submenu appears.
b) Click the Base Components button in the submenu.
c) Click the Update button in the submenu and follow the instructions
3. To install the Precise 100 Client software, click the Precise 100 Client button and
follow the instructions.
4. Restart the computer.
parallel port connector
pass-through
PS/2 connector
keyboard
PS/2 connector
NOTE: The parallel port must be set to ECP
mode, otherwise the fingerprint reader will not
function properly. Please refer to the computer
manual for additional information, or follow the
instructions below.
Enrolling a User
NOTE: If the CD does not start automatically, start
the CD from the desktop by double-clicking My
Computer > CD > MasterSetup.exe icon.
To set the parallel port:
1. Access the system setup utility on your computer. On most computers this is done
by pressing the F1, F10, Delete or Esc key during system booting, i.e. immediately
after switching on the computer.
1. If you have a Precise 100 Reader with USB connector, please connect it to your PC
now. Windows 2000 will detect the new hardware and install the necessary drivers
from the CD. If you have a Precise 100 Reader with parallel port connector, click the
Parallel Driver button to install the necessary parallel port drivers.
2. Find the parallel port mode and set it for ECP. If the ECP selection is unavailable,
the parallel port is probably already set for ECP.
2. If you are using Windows NT you must install the Microsoft Smartcard Base
Components, if not previously installed. If you are using Windows 2000 do not
install the Smartcard Base Components, the system may crash.
3. Save your changes and exit the system setup utility.
NOTE: To be able to log into a domain server account, the user has to be enrolled on the domain server. If the
user is enrolled on a local computer, he or she can only log into that computer using a fingerprint.
1. Log on as an administrator.
2. Click Start > Programs > Precise Biometrics > BioManager.
The BioManager screen will appear.
4. Enter the desired information in the Username, Full Name and Description field.
If you have a Precise 100 SC Reader, you can choose to store the data on the
smart card. Click Next. The Reading Fingerprints screen will appear.
5. Select the fingerprint to be registered by clicking
in one of the checkboxes.
6. Follow the instructions on the screen. To ensure
a good image, make sure the centre of the finger
pad is placed in the sensor centre. The fingerprint
is read four times, for the system to select and
verify a good print.
7. Register another fingerprint, or click Next. The
Logon Information screen will appear.
8. Select primary logon finger. The primary logon
finger is the default finger that will be used to log
into the system.
NOTE: If a current password user is enrolled, the current password is
no longer valid. A new password must be typed, in order for the user to log on with a password.
3. Click User > New User. The User Information screen
of the Fingerprint Enrolment wizard will appear.
9. Click Next. The saving screen will appear.
10. Click Finish to store the data.
Logging on Using
a Fingerprint
1. If you have a Precise 100 SC Reader, insert your
smart card into the reader and place your finger on
the reader. If you have a Precise 100 A Reader,
simply place your finger on the reader. You can also
press the Enter key and then enter your Username.
2. Place your primary logon finger on the fingerprint
reader sensor. The Verify Fingerprint screen will appear.
3. Keep your finger placed on the
sensor as long as the yellow
light is flashing. The system
verifies your fingerprint and
access rights for the selected
domain.
If verification fails, make sure:
●
your username and domain are correct
●
you place the selected finger on the centre of the sensor
Correct Finger
Placement
Most of the information in a fingerprint is located in the middle of the finger pad.
Therefore, it is important that the middle of the finger pad is placed in the sensor
centre at enrolment and logon.
●
●
●
Quick Reference
Do not “roll” your finger pad. Just press it flat to the sensor.
Place the centre of your finger pad in the sensor centre.
Use medium pressure and avoid rotating your finger.
Perfectly placed finger.
Good image:
fingerprint in
the middle,
medium pressure
to the sensor.
Precise 100 Client for
Windows NT/2000
© Precise Biometrics AB, 2000
info@precisebiometrics.com
www.precisebiometrics.com
Telephone
Sweden: +46-46-311 100
United States: +1-703-848 9266
To get more experience in logging on with your fingerprint, refer to the Precise Demo.
Access the Precise Demo by clicking Start > Programs > Precise Biometrics > Demo.
Precise 100 SC
Precise 100 A
All rights reserved. Second Edition September 2000
P/N: AM010013 R2A
For more information on the Precise 100 system,
please refer to the User’s Manual located on the software CD.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2000:10:05 10:11:28+02:00
Create Date                     : 2000:10:05 10:10:58+02:00
Producer                        : Acrobat Distiller 4.0 for Macintosh
Page Count                      : 4

EXIF Metadata provided by EXIF.tools