User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1565414 |
| Application ID | VWnqv6xqoe/Wpa5n9MhdcA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 101.67kB (1270895 bits) |
| Date Submitted | 2011-10-21 00:00:00 |
| Date Available | 2012-04-18 00:00:00 |
| Creation Date | 2017-11-03 17:11:28 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-11-03 17:11:28 |
| Document Title | User Manual |
| Document Creator | Microsoft® Word 2010 |
M66 Design Guide M66 GSM / GPRS Wireless Module Design Guide Rev. 0.0.1 2011/6/10 Copyright © 2008 Qisda Corporation. All rights reserved. This document contains proprietary technical information which is the property of Qisda Corporation and is issued in strict confidential and shall not be disclosed to others parties in whole or in parts without written permission of Qisda Corporation. The documents contain information on a product, which is under development and is issued for customer evaluation purposes only. Qisda may make changes to product specifications at any time, without notice. Module Business Division Mobile Communications BU Qisda Corporation 18 Jihu Road, Nei-Hu, Taipei 114, Taiwan Tel: +886-2-2799-8800 Fax: +886-2-2656-6398 http://Qisda.com Copyright ©2011 Qisda Corporation. Confidential Property M66 Design Guide History Version VER: 0.0.1 Date Notes 2011/6/10 First release Version: 0.0.1 -2- 2011/6/10 M66 Design Guide FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. RF Exposure Information This Modular Approval is limited to OEM installation for mobile and fixed applications only. The antenna installation and operating configurations of this transmitter, including any applicable source-based time-averaging duty factor, antenna gain and cable loss must satisfy MPE categorical Exclusion Requirements of §2.1091. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons, must not be collocated or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Version: 0.0.1 -3- 2011/6/10 M66 Design Guide The end user has no manual instructions to remove or install the device and a separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations. Maximum antenna gain allowed for use with this device is 2 dBi. When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text: “Contains FCC ID: VRSGM6601”. Version: 0.0.1 -4- 2011/6/10 M66 Design Guide IC Regulations: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This Category II radio communication device complies with Industry Canada Standard RSS-310. Ce dispositif de radiocommunication de catégorie II respecte la norme CNR-310 d’Industrie Canada. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Version: 0.0.1 -5- 2011/6/10 M66 Design Guide Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Labeling Requirements for the Host Device (from Section 3.2.1, RSS-Gen, Issue 3, December 2010): The host device shall be properly labeled to identify the module within the host device. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the Industry Canada certification number of the module, preceded by the words “Contains transmitter module”, or the word “Contains”, or similar wording expressing the same meaning, as follows: Contains transmitter module IC: 8729A-GM6601 This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Version: 0.0.1 -6- 2011/6/10 M66 Design Guide Index POWER-ON / POWER-DOWN SEQUENCE .................................................................................... 9 1.1 POWER-ON SEQUENCE ........................................................................................................................... 9 1.2 SWITCHED ON ..................................................................................................................................... 10 1.3 M66 RESTARTS ...................................................................................................................................... 10 1.4 M66 SWITCH OFF ..................................................................................................................................11 INITIALIZATION PROCEDURE ........................................................................................................ 12 SHORT MESSAGE .................................................................................................................................. 14 3.1 INITIALIZATION .................................................................................................................................... 14 3.2 SENDING A SMS ................................................................................................................................... 14 3.3 RECEIVING A SMS ................................................................................................................................. 15 VOICE CALL ............................................................................................................................................ 16 4.1 INITIALIZATION .................................................................................................................................... 16 4.2 MOBILE ORIGINATED CALL (MO) ......................................................................................................... 17 4.3 MOBILE TERMINATED CALL (MT) ........................................................................................................... 17 PPP DATA CALL ..................................................................................................................................... 18 5.1 GET READY FOR PPP DATA CALL............................................................................................................ 18 5.2 DIALING .............................................................................................................................................. 18 M2M ............................................................................................................................................................ 19 M66 INTERFACE .................................................................................................................................... 20 7.1 POWER ................................................................................................................................................ 21 7.2 UART.................................................................................................................................................. 23 7.3 AUDIO ................................................................................................................................................. 25 7.3.1 Microphone ..................................................................................................................................... 25 7.3.2 Receiver/Speaker ............................................................................................................................. 26 7.3.3 Grounding and Layout ...................................................................................................................... 27 7.4 SIM ..................................................................................................................................................... 28 7.4.1 ESD ................................................................................................................................................ 29 7.4.1.1 ESD protection diodes ................................................................................................................. 29 7.4.1.2 SIM holder ................................................................................................................................. 31 7.5 ANTENNA............................................................................................................................................ 32 7.6 ANTENNA STATUS DETECTION APPLICATION.......................................................................................... 33 Version: 0.0.1 -7- 2011/6/10 M66 Design Guide Version: 0.0.1 -8- 2011/6/10 M66 Design Guide Power-on / Power-down Sequence The operation voltage of M66 is between 3.3 and 4.2 V (A restricted operation range is between 4.2 and 4.7 V). It is recommended to support a stable voltage in the proper range which is between 3.8 and 4V. 1.1 Power-on sequence 1. The initial state: VBAT: 0V TERM_ON: LOW 2. Power on: VBAT: HIGH (recommended: 3.8V-4V) TERM_ON: HIGH 3. Switch on M66: VBAT: Keep HIGH TERM_ON: Keep LOW for 50ms then pull HIGH and remains. Boot-up sequence ※ Please note that it is recommended to wait at least 50ms to pull LOW the TERM_ON pin after power on (Put VBAT as HIGH). The system will not start if TERM_ON is LOW before power on. ※ An open-collector circuit is needed when using MPU (client) to control the TERM_ON pin. Version: 0.0.1 -9- 2011/6/10 M66 Design Guide 1.2 Switched on The factory default baud rate of M66 is 9600. The prompt”AT-Command Interpreter ready” is output via UART1 after switched on. LED status indication：The LPG pin (PIN 13) of M66 is used to indicate the M66/network status. The LPG outputs different kind of pattern as follows: M66/Network status LPG pattern(unit：sec) M66 startup Always High Power saving mode (Deep sleep mode) Always Low No network (No SIM、PIN required、Not registered…) High: 0.1，Low: 0.9 Registered and idle High: 0.1，Low: 2.9 Connected(MO/MT Call) Always High GPRS transmitting/receiving data Blinking(Note1) Note 1：While in data mode, the LPG pattern is blinking if data is transmitting or receiving. And the LPG keeps LOW if there is no data transmitting/receiving. 1.3 M66 restarts 1. General restart procedure： a. AT+CFUN=0, stop all network-related action. b. AT%RST to restart M66. 2. Emergency restart procedure： a. In case there is no response of any AT commands. b. Pull EMERG_OFF low for 50ms and then pull high. c. Proceed the startup procedure(Please refer to 1.1) Version: 0.0.1 - 10 - 2011/6/10 M66 Design Guide 1.4 M66 switch off 1. SW switch off procedure： a. AT+CFUN=0, stop all network-related action. b. AT%MSO, switch off M66. c. Remove VBAT. 2. HW switch off procedure： a. AT+CFUN=0, stop all network-related action. b. Pull TERM_ON low for 50ms and then pull high to shutdown M66. c. Remove VBAT. Version: 0.0.1 - 11 - 2011/6/10 M66 Design Guide Initialization procedure In this chapter, it describes the initialization procedure when using M66. A suggested procedure and description of initialization. AT To check UART1 works normally. The factory default baud OK rate is 9600 without HW flow control. The 3-wired UART is also supported, M66 internally pull low CTS. ATE0 Echo off. OK AT%TSIM To check SIM existence. %TSIM 1 1: SIM exist, 0: No SIM OK AT+CPIN? To check SIM and PIN1 +CPIN: READY READY: PIN1 passed OK AT+CSQ To check the RSSI value. +CSQ: 28,99value: 0~31, 99 means no network. OK AT+CREG=1 To enable network registration unsolicited result code. OK AT+COPS? To query the network +COPS: 0,0,"CHINA MOBILE ”CHINA MOBILE” is registered. OK AT+CGATT？ To check GPRS attached or detached +CGATT: 1 GPRS attached. OK Version: 0.0.1 - 12 - 2011/6/10 M66 Design Guide AT+GMI To query the manufacturer ID. Qisda OK AT+CGMR To query the SW/HW revision. HW REVISION: S02 HW information SW REVISION: 0.01 SW information BUILD DATE: 2011/01/05 SW revision building date BUILD TIME: 16:05 SW revision building time OK AT+GSN To query the product serial number ID. 358688000000XXX OK AT+CIMI To query the international mobile subscriber ID. 466018770553XXX OK Version: 0.0.1 - 13 - 2011/6/10 M66 Design Guide Short Message There are two formats of SMS which are PDU (Protocol Data Unit) and Text. The format could be selected by AT command. The default format id PDU and it is still recommended to select the mode during initialization. 3.1 Initialization The suggested SMS initialization procedure and description AT+CMGF=1 To select the text format. OK (Text format for example) AT+CSCA? To query the Service Center Address +CSCA: “+886935074443”,145 In general, this information is stored in SIM. If not, please contact the operator for more information. The SMS is OK normally executed only if the service center address is set correctly. AT+CPMS=”SM”,”SM”,”SM” To select memory storages. +CPMS: 3, 15, 3, 15, 3, 15 OK AT+CPMS? To query memory storages and remaining space. It must +CPMS: "SM", 3, 15, "SM", 3, 15, "SM", 3, 15 have enough space when using SMS. Please erase the messages if it is full. OK 3.2 Sending a SMS The suggested procedure of sending message and its description AT+CMGS=“12345678900” To send a message. The number is between quotation >Test message marks. To text the content and finished with ctrl-z for +CMGS: 99 sending. Sending successfully indication +CMGS: . OK Version: 0.0.1 - 14 - 2011/6/10 M66 Design Guide 3.3 Receiving a SMS The suggested procedure of receiving message and its description AT+CNMI=2,1 To set New Message Indication. There will be no OK indication if NMI does not set. +CMTI: “SM”,1 A new message is stored in SIM. AT+CMGR=1 To read the 1st message stored in SIM. +CMGR:"REC The information of the message. UNREAD","886960530355","","2011/01/05 20:23:44+32" tset The content of the message. OK AT+CMGD=1 To delete the 1st message. OK AT+CMGD=1,4 To delete all messages. OK Version: 0.0.1 - 15 - 2011/6/10 M66 Design Guide Voice Call The acoustic is highly related to the HW design especially the tooling. Please contact us for acoustic tuning if needed. And please provide the equipment(s), we will arrange it and provide the final acoustic parameters. The tuning has its limitation, not all equipments could reach the best quality. The schematics or tooling may need to be modified. Please also provide the schematics about the audio part. Each product is identical and unique. Please do not use the same parameters on different products. 4.1 Initialization The basic initialization procedure and its description AT%NFI? To query the current audio input path. %NFI: 0,-6,0 OK at%NFO? To query the current audio output path. %NFO: 0,6,0 OK AT%SNFS=1 To select the 2nd audio path. OK AT%VLB=1 To enable the echo suppression. OK AT%STN=-26 To set the sidetone gain to mute. OK The basic procedure is only tuning gain and path. Please contact us for a better quality if distortion, noise, echo… happens to your products. Version: 0.0.1 - 16 - 2011/6/10 M66 Design Guide 4.2 Mobile Originated call (MO) Outgoing call (MO) ATD10086; To make an MO call. The number is 10086. Please ended with a OK semicolon in voice call. ATH To disconnect the call. OK NO CARRIER 4.3 The call is disconnected by remote party. Mobile Terminated call (MT) Incoming call (MT) AT+CLIP=1 To enable a called subscriber to get the calling line identity of the OK calling party when receiving a MT call. RING Incoming call indication. +CLIP: "1234567",129,"",0,"",0 The information of the incoming call. The caller ID is 1234567. RING +CLIP: "1234567",129,"",0,"",0 (Notify every 3 seconds by default.) ATA To Answer the call. OK ATH To disconnect the call. OK NO CARRIER Version: 0.0.1 The remote side disconnect the call. - 17 - 2011/6/10 M66 Design Guide PPP Data Call 5.1 Get ready for PPP data call Initialization of PPP data call AT+COPS? To make sure that a registered network is available. +COPS: 0,0,“CHINA MOBILE” OK AT+CSQ To check the signal strength (rssi). The maximum number +CSQ: , for rssi is 31. OK AT+CGATT? To make sure that GPRS is enabled. +CGATT:1 OK AT+CGDCONT=1,“IP”,“CMNET” To register to CMNET of CHINA MOBILE. OK 5.2 Dialing To execute ATD*99# with PPP tool. Version: 0.0.1 - 18 - 2011/6/10 M66 Design Guide M2M TBD Version: 0.0.1 - 19 - 2011/6/10 M66 Design Guide M66 Interface M66 50-pin connector interface: PIN Name SIM_CLK SIM_VCC SIM_IO SIM_RST SIM_DET SIM_GND NC GND USB_DM USB_DP NC NC LPG ANT_EMG RXD Ant_Dect_EN TXD VDD-RTC RXD2 TXD2 GND GND GND GND GND VBAT VBAT VBAT VBAT VBAT VDD-IO RING NC RTS NC NC CTS Ant_Dect_ADC DCD EMERG_OFF TERM_ON GND MIC2 MICBIAS MIC1-P MIC1-N SPK-N SPK-P EAR-P EAR-N Version: 0.0.1 PIN No. 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 I/O/P Output Power Input/Output Output Output Desctiption SIM clock SIM power SIM input/output SIM reset SIM detect SIM ground Input/Output Input/Output Ground USB DM USB DP Output Output Output Input Input Power Output Input LED paging indicator Emergency indication for antenna detection UART1 RXD Interrupt for 36V applied on the antenna signal line UART1 TXD RTC backup battery connection pad UART2 RXD UART2 TXD Ground Power Power (recommend 3.8V~4.0V) Power Output Output Input Input UART1 power supply UART1 RING indicator UART1 DSR UART1 RTS UART1 DTR Output Input Output Input Input UART1 CTS Input Output Input Input Output Output Output Output UART1 DCD Hardware power off Power On Ground Hands-free MIC input Hands-free MIC bias MIC positive input(+) MIC negative input(-) Hands-free speaker negative output (-) Hands-free speaker positive output (+) Handheld earpiece positive output (+) Handheld earpiece negative output (-) - 20 - 2011/6/10 M66 Design Guide 7.1 Power The operating voltage of M66 is between 3.3V and 4.7V. Please make sure that the supply voltage is still in the proper range when a maximum current is drawn from the power supplu when a maximum RF output power is required. Please note that once the supply voltage to M66 drops below 3.3V, module would be shut down. If a power supply regulator is used for VBAT (power supply to M66), please make sure the maximum output current rating should be more than 2A which is the minimum requirement for a maximum RF output power. A reference design for a switching power supply is shown below. The voltage rating of C31 and C35 should be raised higher if Vin is greater than 12V. LM2676S-ADJ (or LM2673S-ADJ) can be used as the switching regulator in the reference design. C58 1K 1% R28 2.49K 1% 100uF/16V TO-263 CB VBAT 33uH/3A D5 Vout ON//OFF C31 Vin VBAT L6 CON3-9V D4 S3J C35 0.47uF/16V GND J6 10nF/50V FB U3 C30 LM2676S-ADJ C33 330uF/10V RB051L-40 C34 0.1UF R27 6.8N C51 100pF C36 3.3nF Vbatt=Vfb*(1+R27/R28)=4.21V Vfb=1.21V A large capacitor with low ESR or parallel capacitors can be used to compensate the insufficient supply current provided by the power regulator. The required capacitance can be calculated from the following equations. C = Capacitance in μF Δt = GSM time slot (577 μs) Q = Electricity charger ΔU = Voltage drop ΔI = Compensation in current (the required current – the supplied current) Version: 0.0.1 - 21 - 2011/6/10 M66 Design Guide During power layout design, there are 2 reminders A. Width A.1 VBAT width: at least 80mil. B. Recommend to have at least 7 via holes if VBAT needs to go through different layers to have a minimum resistance. Version: 0.0.1 - 22 - 2011/6/10 M66 Design Guide 7.2 UART The serial interface UART1 supports 6-wired, 4-wired, or 2-wired interface. M66 communicates with an external MPU via UART1. The factory default baud rate of UART1 is 9600 and it supports auto baud rate. The main function of UART2 is for debug. It communicates with PC via UART transceiver. M66 serves as a DCE and the UART pin definition is as the following table. RS232 pin Name Transmit Data (TXD) Receive Data (RXD) Request To Send (RTS) Clear To Send (CTS) Data Carrier Detect (DCD) Ring Indicator (RI) Direction DTE M66 DTE M66 DTE M66 DTE M66 DTE M66 DTE M66 M66 pin name TXD RXD RTS CTS DCD RI M66 pin no. 17 15 34 37 39 32 It is recommended to use 3V interface. Version: 0.0.1 - 23 - 2011/6/10 M66 Design Guide A level shift circuit should be added to the system if the UART interface of host side is not 3V. The following is an example of 5V interface. Version: 0.0.1 - 24 - 2011/6/10 M66 Design Guide 7.3 Audio It divides into 2 parts, microphone (uplink) and receiver/speaker (downlink). 7.3.1 Microphone Microphone schematics design is shown below for reference: 1. Please use the differential circuit design. 2. The microphone signal traces should be as short as possible. 3. Add decoupling circuits for external microphone bias and audio power supply to reduce TDD noise. 4. Audio traces should be kept away from the VBATT and high speed clock traces. 5. Good shielding for audio path including components and traces. If possible, use via holes to connect the ground shielding above and beneath the audio signals. 6. Twisted pair for external microphone lines. No necessary to use copper foil to wrap around external microphone lines. 7. The distance between microphone and antenna should be at least 10 cm. 8. Add the small capacitor (33pF) across the microphone input traces to suppress the noise. Version: 0.0.1 - 25 - 2011/6/10 M66 Design Guide 7.3.2 Receiver/Speaker Receiver/speaker schematics design is shown below for reference: As to the Hands-free application, it is suggested to use MIC2/MICBIAS and SPK-P/SPK-N to get a better audio performance. SPK-P/SPK-N could drive a 8Ω speaker directly without an external audio amplifier and the output power is 500 mW. R17 220 C22 2.2U 6.3V MICBIAS R18 2.2K J J3 MIC2 C27 33P J C28 1000P K CON3 J4 SPK-P C30 33P J SPK-N CON2 C31 33P J Version: 0.0.1 C32 33P J - 26 - 2011/6/10 M66 Design Guide 7.3.3 Grounding and Layout Good grounding and conductive screws/screw holes are important to the audio quality and performance. Please take special attention to the PCB layout of the screw holes and the surrounding ring area. They should be copper plated and electrically conductive. Tighten the screws which should be electrical conductive. The screw holes and surrounding pad area should be conductive. Version: 0.0.1 - 27 - 2011/6/10 M66 Design Guide Recommended audio trace layout is illustrated in the following diagram. Balanced circuit 7.4 SIM The Vpp pin (Programming Voltage) is no function in current plug-in SIM. Please leave it opened. The reference circuit is depicted below. Version: 0.0.1 - 28 - 2011/6/10 M66 Design Guide 7.4.1 ESD 7.4.1.1 ESD protection diodes An ESD protection circuit could prevent the SIM cards from being damaged by ESD. Please add an ESD circuit close to the CIM circuit to prevent ESD damaged. It is suggested to use the following EDS protection diode. Version: 0.0.1 - 29 - 2011/6/10 M66 Design Guide Electrical characteristics of the ESD protection diodes are shown as below for reference. Version: 0.0.1 - 30 - 2011/6/10 M66 Design Guide Recommended ESD protection components from different vendors: SESMF05C SENZQA5V6AV5 SEDF6A6V8 AMOTECH AVSC 5S 04F 025 7.4.1.2 SIM holder Besides ESD protection, the placement and layout of the SIM holder is also important to SIM protection. 1. The ESD protection unit should be placed close to the SIM holder. 2. The ground pin of ESD protection unit should be directly connected to main ground. It will make the ESD energy discharged to ground plane. 3. The trace width should be at least 0.3mm between SIM holder and ESD protection unit. 4. The ESD protection unit should be between SIM holder and M66. 5. The trace between ESD protection unit and M66 should be in a different layer and the width should be at least 0.1mm. Version: 0.0.1 - 31 - 2011/6/10 M66 Design Guide 7.5 Antenna M66 has an antenna pad on the BOTTOM side. It is possible to solder the coaxial cable directly. The impedance of the cable should be 50 ohm (±10%) 1mm 2mm 7.5mm 7.5mm M66 antenna pad Version: 0.0.1 - 32 - 2011/6/10 M66 Design Guide 7.6 Antenna status detection application Being able to detect and diagnose the antenna is a valuable feature for many system integrators, and especially for automotive applications. The ability to detect whether the antenna is connected to the communication appliance is useful for diagnosing installation or production problems as well as any tampering with the system. Users can detect the connection status by AT command. The responses are three kinds of status: 1. Antenna is connected to the RF cable properly. 2. The signal line of antenna is disconnected from RF Cable. 3. The signal line of antenna is connected to GND by accident. If the signal line of antenna is short circuited to the +36V Power line ,(Ex. The battery in automobile), M66 will inform MPU of emergency status by ANT_EMG pin. Application Reference Circuitry is shown below. The following assumes that the application is using a commonly found 10KΩ DC terminated antenna. The green bold line is micro-strip line with 50Ω characteristic impedance. PAD1 is the RF connector for Antenna. R27 R28 8.2K F R29 15K F R30 15K F R31 68K F 18K F Ant_Dect_EN Ant_Dect_ADC VIO_3V3 2,3 L2 18NH J ZD1 MM5Z3V0 GND GND 47P F ANT-PAD Version: 0.0.1 C40 0J L3 NC L4 NC - 33 - J8 2K90002003 R32 GND PAD1 GND 2011/6/10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Copy, Extract, Print high-res Language : zh-TW XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Create Date : 2011:10:19 17:06:29+08:00 Creator Tool : Microsoft® Word 2010 Modify Date : 2011:10:19 18:31:04+08:00 Metadata Date : 2011:10:19 18:31:04+08:00 Producer : Microsoft® Word 2010 Format : application/pdf Document ID : uuid:dc4b7941-032c-4308-b7fc-e459a7812d1c Instance ID : uuid:0df21f96-8a26-4d85-b0e5-4ff9303a7048 Page Count : 33 Creator : Microsoft® Word 2010EXIF Metadata provided by EXIF.tools