Quanzhou Wouxun Electronics WOUXUN03 Two-way Radio User Manual
Quanzhou Wouxun Electronics Co., Ltd. Two-way Radio Users Manual
Users Manual
Thanks for buying the KG-699E series transceiver. This transceiver offers latest in design, multi-functionality, stable behaviour and easy operation. We believe you will be pleased with the high quality and dependable features for all your communication needs. User Safety, Training, and General Information READ THIS IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION BEFORE USING YOUR PORTABLE TWO-WAY RADIO. Compliance with RF Energy Exposure Standards Your two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environment at duty cycles of up to 50% talk-50% listen and should be used for occupational use only. In terms of measuring RF energy for compliance with the FCC exposure guidelines, your radio radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. NOTE The approved batteries supplied with this radio are rated for a 5-5-90 duty cycle (5% talk-5% listen-90% standby), even though this radio complies with the FCC occupational RF exposure limits at duty cycles of up to 50% talk. Professional FM Transceiver Your two-way radio Complies with the following of RF energy exposure standards and guidelines: • United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 subpart J • American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 • Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1999 Edition • International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 Operational Instructions and Training Guidelines To ensure optimal performance and compliance with the occupational/controlled environment RF energy exposure limits in the above standards and guidelines, users should transmit no more than 50% of the time and always adhere to the following procedures: Transmit and Receive To transmit (talk), push the Push-To-Talk (PTT) button; to receive, release the PTT button. Hand-held radio operation Hold the radio in a vertical position with the microphone 5 cm away from the lips and let the antenna farther away from your head. Body-worn operation Always place the radio in a approved clip, holder, holster, case, or body harness for this product. Use of non- -approved accessories may exceed FCC RF exposure guidelines. Antennas & Batteries • Use only approved, supplied antenna or approved replacement antenna. • Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations. • Use only approved, supplied batteries or approved replacement batteries. • Use of non- -approved batteries may exceed FCC RF exposure guidelines. Approved Accessories For a list of approved accessories, see the accessories page of this user manual or visit the following website which lists approved accessories:http://www.wouxun.com Professional FM Transceiver Notices to the User • Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. • Illegal operation is punishable by fine or imprisonment or both. • Refer service to qualified technicians only. WARNING: It is important that the operator is aware of and understand hazards common to the operation of any transceiver. Explosive environment(such as gases, dust, fumes, etc). Turn off your transceiver while talking on fuel, or while parked in gasoline service stations. If you require this machine to be developed or some changed, pleased connect with or your dealer. FCC Caution: This equipment has been tested and found to comply with the part 90 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmfu l interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following Measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Licensing Requirements Your radio must be properly licensed Federal Communications Commission prior to use. Your Wireless dealer can assist you in meeting these requirements. Your dealer will program each radio with your authorized frequencies, signaling codes, etc., and will be there to meet your communications needs as your system expands. Professional FM Transceiver Precautions Only qualified technicians are allowed to maintain this product. Do not use the radio or charge a battery in explosive areas such as coal gas, dust, steam, etc. Switch OFF the radio while refueling or parking at gas station. Do not modify or adjust this radio without permission. Do not expose the radio to direct sunlight over a long time, nor place it close to heating source. Do not place the radio in excessively dusty, humid areas, nor on unstable surfaces. Safety: It is important that the operator is aware of and understands hazards common to the operation of any radio. CE Caution: Hereby, declares that this Two-way radio is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the DOC may be obtained through the following address. Address: No.928 Nanhuan Road, Jiangnan High Technology Industrial Park, Quanzhou, Fujian 362000, China Contents Unpacking and checking of your equipment Supplied accessories Description of functions Getting started LCD display Description of transceiver Speed search DTMF encoding Switch working mode Shortcut operation sheet How to operate Lock menu function Setting dual standby (TDR) ---- MENU O Setting channel step (STEP) ---- MENU 1 Setting squelch level (SQL-LE) ---- MENU 2 Setting batterypack savemode (SAVE) --- MENU 3 Selecting transmitpower (TXP) ---- MENU 4 Setting voice encrypt compress (SCR)--- MENU 5 Transmit over timer (TOT) ---- MENU 6 Setting VOX (VOX) ---- MENU 7 Setting wide and narrow bandwidth (WN) ---- MENU 8 2-3 4-7 5-6 8-13 14-55 14 14-15 15-16 16 17 17 18 18 19 19 Professional FM Transceiver Setting auto backlight (ABR) ---- MENU 9 Setting receive CTCSS (R-CTCS) ---- MENU 10 Setting receive DCS (R-DCS) ---- MENU 11 Setting transmit CTCSS (T-CTCS) ---- MENU 12 Setting transmit DCS (T-DCS) ---- MENU 13 Setting voiceguide (VOICE) ---- MENU 14 Setting beepprompt function (BEEP) ---- MENU 15 Setting DTMF sidetone (DTMFST) ---- MENU 16 Setting transmit overtime alarm (TOA) ---- MENU 17 Busy channel lockout (BCL) ---- MENU 18 Adding channelscan (SC-ADD) ---- MENU 19 Priority scan function (PRI-SC) ---- MENU 20 Setting priority channel scan function (PRI-CH) ---- MENU 21 Setting scanmode (SC-REV) ---- MENU 22 Setting option signal (OPTSIG) ---- MENU 23 Setting mutemode (SPMUTE) ---- MENU 24 PTT ID (PTT-ID) ---- MENU 25 Setting ANI ID CODE transmit (PTT-ID) ---- MENU 26 Setting signal information (S-INFO) ---- MENU 27 19-20 20 21 21 22 22 23 23-24 24 24 25 25 26 27 29-30 32 32-33 33 34 Contents Emergency calling type (EMC-TP)---MENU 28 Emergency calling channel (EMC-CH)---MENU 29 Select ringmode (RING-M)---MENU 30 Setting ringtime(RING-T)---MENU 31 Edit channelname (CHNAME) ---- MENU 32 Setting transmit segment when in dual standby (TDR-AB) ---- MENU 33 Setting A segment channel display mode (CA-MDF)---MENU 34 Setting B segment channel display mode (CB-MDF)---MENU 35 Setting keyboard lock (AUTOLK) ---- MENU36 Setting power on message (PONMSG) ---- MENU 37 Setting sidekey 1(PF1)---MNEU 38 Setting topkey (PF2) ---MENU 39 Define MONI key (MONI) ---- MENU 40 Selecting standby display color (WT-LED) ---- MENU 41 Selecting receive display color (RX-LED) ---- MENU 42 Selecting transmit display color (TX-LED) ---- MENU 43 Setting memory channel=setting co-channel and dis-channel (MEM-CH) ---- MENU 44 Delete channel (DEL-CH) ---- MENU 45 34 35 35 36 36-37 38 38-39 39-40 40-41 41 41-43 43-44 44-45 45 45 46 46-47 48 Professional FM Transceiver Setting frequencyshift direction (SFT-D) ---- MENU 46 Setting offsetfrequency (OFF-SET) ---- MENU 47 ANI CODE edit (ANI) ---- MENU 48 Setting VOX-T (VOXT) ----MENU 50 Companding (COMP) ----MENU 51 Setting reset (RESET) ---- MENU 52 Setting reverse frequency function Lowvoltage batterypack voiceprompt Setting transmit overtime prompt Adding channelscan Wireclone function Programming repeater function How to use your intelligentcharger Trouble shooting Technology parameter Appendix 1 (CTCSS) Appendix 2 (DCS) Technology specification Optional accessories Announce 48 49-50 50 50-51 51 51-52 52 53 53 53 53 54-55 55 56-57 58-60 58 59-60 61 62 63 Unpacking and checking of your equipment Carefully unpack the transceiver. We recommend that you identify the items in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, please notify your dealer. Supplied accessories A/B Professional FM Transceiver KG-699E MENU UP DOWN SQL SAVE SCR TOT W&N ABR STEP TXP VOX EXIT T- R SCAN TDR Transceiver Switching adapter High gain antenna Beltclip Li-ion batterypack Handstrap User's manual Intelligent charger Service card 01 Description of functions Professional FM Transceiver 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. UHF: 406.125-469.975MHz Output power: UHF: 4W/1W 200 memory channels In frequency mode, VHF Dual frequencies or UHF Dual frequencies display and standby. In channel mode, VHF Dual channels or UHF Dual channels display and standby. DTMF encoding and decoding 5 tones (including 15 kinds standard) 2 tones 1750Hz burst tone Priority scan FM radio with frequency display DCS/CTCSS of RX and TX can be set respectively ANI (caller ID) VOX All calls, group calls and selective calls function Calling ring function Scrambler available 105 groups DCS / 50 groups CTCSS Voiceguide (English/Chinese) Wide/Narrow bandwidth selection (25KHz/12.5KHz) Three color back light display. 02 Description of functions 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 03 Channel name edit available. Channel order, channel frequeny, channel name multi-display method Reverse frequency function Distant urgency alarm function Multi scan function Channel steps (5/6.25/10/12.5/25KHz) High/Low power changeable when on transmitting. Intelligentcharger ( Warning sound and dualcolor light) TX/RX splitselection (0-99.950MHz) Set frequencyshift direction Stopwatchtimer function Busy channel lockout Multi display modes when power on (full screen / Batt-V / others) Lowvoltage batterypack voiceprompt Transmit overtime prompt Keyboard lock (auto / manual) Adding channelscan function Programmable by computer Menu / Channel reset Wireclone function Powersaving function voice compress function Getting started Professional FM Transceiver LCD display On the display you will see various indicators that show what function you have selected. Sometimes you may not recall what those indicators mean, or how to select them, in such a case, you can refer to the table below. Split Split DCS DTMF-encoding and -decoding CTCSS Switch to desired frequency High/Low power transmit Reverse frequency Dual standby indicator VOX Priority scan Bandwidth indicator Scrambler state Batterypack status indicator Menu order / Channel order Menu order / Channel order Keypadlock Busychannel light Note: Batterypack capacity indicator (full) Batterypack capacity spare indicator Batterypack capacity is exhausted Receive signal meter 04 Getting started Description of transceiver (Double knob) Topkey: Distant urgency alarm Channel switch Antenna Powerswitch / Volumecontrol B channel receive and transmit light A channel receive and transmit light A or B channel switchkey Screen / LCD display Numberkey Exitkey Reverse frequency / Scankey KG-699E Functionkey Lockkey Up /Downkey 05 Professional FM Transceiver PTT (Push-To-Talk) key Sidekey 1: radio/CALL/ NO-SUB/JP-PRI/JP-EMC Speaker/ Microphonejacks Batterylatches Sidekey 2: monitor 06 Getting started Speed search When setting each function or parameter, press the or key one time can speed search the function or parameter. DTMF encoding This transceiver has DTMF encoding. By pressing the right number key on transmit you can choose the right DTMF tone which you want to TX. Switch working mode + POWER ON Channel mode Frequency mode If you want to transmit the 1750Hz burst tone, you just press PTT and sidekey 1 at the same time. 07 Shortcut operation sheet Professional FM Transceiver Function Function Enter order name function set 0 Setting dual standby 1 Setting channel step 2 Setting squelch level 3 Setting batterypack savemode Screen display Select parameter Selectable parameterexplanation Confirm Back See page Press or key ON: Turn on dual standby Select parameter OFF: Turn off dual standby EXIT P14 -15 Press or key 5 kinds of channelstep Select parameter 5K/6.25K/10K/12.5K/25K EXIT P15 -16 Press or key Squelchlevel from 0-9 Select parameter EXIT P16 Press or key Select parameter EXIT P17 ON: Turn on save function 1:1/1:2/1:3/1:4 OFF: Turn off save function 4 Selecting transmitpower Press or key 6-10: High power (5W). Select parameter 1-5: Low power (1W) EXIT P17 5 Setting voice encrypt compress Press or key Select parameter ON: Turn on scrambler. OFF: Turn off scrambler. EXIT P18 6 Transmit over timer Press or key Select parameter TOT has 40 levels in steps of 15 seconds. OFF: Turn off TOT. EXIT P18 7 Setting VOX Press or key Select parameter VOX has levels from 1 to 10. OFF: Turn off VOX. EXIT P19 8 Setting bandwidth Press or key WIDE: 25KHz. Select parameter NARROW: 12.5KHz. EXIT P19 08 Shortcut operation sheet 9 Setting auto back light Press or key Select parameter ON: Turn on auto back light OFF: Turn off auto back light EXIT P19 -20 Press or key Select parameter 50 groups CTCSS (67 -254.1Hz) OFF: Turn off CTCSS EXIT P20 EXIT P21 EXIT P21 Press or key 105 groups DCS (D023N-D754N) Select parameter OFF: Turn off DCS EXIT P22 EXIT P22 EXIT P23 ABR 10 Setting receive CTCSS Press or key 105 groups DCS (D023N-D754N) Select parameter OFF: Turn off DCS 11 Setting receive DCS 12 Setting transmit CTCSS 13 Setting transmit DCS Press or key Select parameter 50 groups CTCSS (67 -254.1Hz) OFF: Turn off CTCSS 14 Setting voiceguide Press or key Select parameter ENGLSH: English 15 Setting beepprompt Press or key Select parameter ON: Turn on beepprompt 16 Setting DTMF sidetone Press or key Select parameter KEY: Turn on sidekey ANI: Turn on ANI sidetone BOTH: Turn on both sidekey and ANI sidetone OFF: Turn off all EXIT P23 -24 17 Transmit overtime alarm Press or key Select parameter ON: Turn on transmit overtime alarm. OFF: Turn off transmit overtime alarm EXIT P24 OFF: Turn off voiceguide OFF: Turn off beepprompt 09 Professional FM Transceiver 18 Busy channel lockout 19 Adding channelscan ABR 20 Setting priority scan function 21 Setting priority channel scan function 22 Setting scanmode 23 Setting option signal 24 Setting mutemode 25 Transmit PTT ID 26 Setting ANI ID CODE transmit Press or key Select parameter ON: Turn on busy channel lockout. OFF: Turn off busy channel lockout. Press or key Select parameter ON: Turn on adding channelscan. OFF: Turn off adding channelscan. EXIT P25 Press or key Select parameter ON: Turn on priority scan function. OFF: Turn off priority scan function. EXIT P25 EXIT P26 P27 Press or key Have 200 groups Select parameter channel can select EXIT P24 Press or key Select parameter TO: Scan with time CO: Scan with carrier wave SE: Does not scan with carrier wave EXIT Press or key Select parameter 4 kind of signals WDTS/DTMF: Double tone signal 2TONES: 2TONES signal 5TONES: 5TONES signal EXIT P28 -31 Press or key Select parameter 3 kinds of mutemode QT/AND/OR EXIT P32 Press or key Select parameter 4 kinds of PTT ID BOT/EOT/BOTH/OFF EXIT P32 -33 Press or key Select parameter Permit transmit ANI delay time from1-30, unit:100ms 0: Turn off manual transmit EXIT P33 10 Shortcut operation sheet 27 Setting signal information Press or key 15 groups signal Select parameter information 28 Emergency calling type Press or key Select parameter 29 Emergency calling channel ABR 30 Select ringmode EXIT P34 EXIT P34 Press or key 200 groups calling channel Select parameter EXIT P35 Press or key 4 kinds of ringmode Select parameter SOUND/BIV/BOTH/OFF EXIT P35 3 kinds of emergency alarm ALARM: Field alarm ENI: Distant alarm BOTH: Field + distant alarm 31 Setting ringtime Press or key Select parameter 10 levels, 1 second differernt 0 menas turn off ringtime prompt EXIT P36 32 Edit channelname Press or key Select parameter The channel name make up of (A to B)26 letters, (0-9)10 numbers,”?” or “+” or “-“. The length at least 6 bits. EXIT P36 -37 EXIT P38 33 Setting transmit segment when in dual standby Press or key A: A segment Select parameter B: B segment 34 Setting A segment channel display mode 35 Setting B segment channel display mode Press or key Select parameter CH: Channel order display FREQ: channelfrequency+ channelorder display. NAME: channelname+ channelorder display EXIT Press or key Select parameter CH: Channel order display FREQ: channelfrequency+ channelorder display. NAME: channelname+ channelorder display EXIT P38 -39 P39 -40 11 Professional FM Transceiver 36 Setting keyboard lock Press or key ON: Turn on autolock Select parameter OFF: Turn off autolock 37 Setting power on message Press or key Select parameter FULL: Full screen display MSG:WELCOME. BATT-V: Battery voltage display EXIT P41 Press or key Select parameter FM: FM radio key. CALL: Signal calling at present NO-SUB: Delete receive JP-PRI: Switch to priority scan channel. JP-EMC: Switch to emergency calling mode. EXIT P41 -43 Press or key Select parameter EMCALL: Turn on alarm function. CALL01-CALL15: Signal calling key. EXIT Press or key Select parameter CONTIN: Continual turn off squelch diagram via keep press MONI key one time. PRESS: Continual turn off squelch diagram via just press MONI key one time. EXIT Press or key Select parameter BLUE: Blue backlight ORANGE: Orange backlight PURPLE: Purple backlight OFF: Turn off backlight Press or key Select parameter BLUE: Blue backlight ORANGE: Orange backlight PURPLE: Purple backlight OFF: Turn off backlight Press or key Select parameter BLUE: Blue backlight ORANGE: Orange backlight PURPLE: Purple backlight OFF: Turn off backlight 38 Setting sidekey1(PF1) 39 Setting topkey(PF2) 40 Define MONI key 41 Setting standy display-color 42 Setting receive display-color 43 Setting transmit display-color ABR EXIT P40 -41 P43 -44 P44 -45 EXIT P45 EXIT P45 EXIT P46 12 Shortcut operation sheet 44 Setting memory channel Press or key Select parameter 200 channels EXIT P46 -47 45 Delete channel Press or key Select parameter 200 channels EXIT P48 46 Frequencyshift direction Press or key Select parameter +: Positive offset - : Negative offset. OFF: Turn off frequencyshift direction EXIT P48 47 Offset frequency Press or key Select parameter From 0 to 99.950MHz can be selectable EXIT P48 -50 48 ANI CODE edit (ANI) Press or key Set Fromby0 programming to 99.950MHz can be selectable Select parameter software 50 Setting VOX-T 51 Setting Companding 52 Setting reset Speed search UP DOWN (See page 7) High/Low power changeable when on transmitting(See page 17) All calls, group calls and selective calls (See page 28-30) Press or key Select parameter Total has 20 levels Unit: 100ms Press or key Select parameter ON: Turn on COMP OFF: Turn off COMP Press or key Select parameter VFO: Menu reset ALL: All message reset EXIT P50 EXIT P50 -51 EXIT P51 EXIT P51 -52 Setting reverse frequency function (See page 52) Lowvoltage batterypack voiceprompt (See page 53) Adding channelscan (See page 53) Wireclone function(See page 53) Programming repeater function (See page 54-55) 13 How to operate Professional FM Transceiver Lock menu functions If you don't need operate menu functions frequently, you can turn off it by KG-699E programming software. The steps as following: 1. Set password of switching between channelmode and frequencymode. 2. Set workmode as channelmode. 3. Turn off operating menu function in channelmode. When you want to use menu functions, input password which you have set, and switch to frequencymode, then you can operate it. NOTE The KG-699E has dualfrequency display. In frequencymode it will display two different transmit and receive frequency at the same time. In channelmode it will display the two different channels plus their parameters. In frequency and channelmode you can switch to A and B segment by pressing the topkey left above the LCD. Setting dualstandby (TDR) --- MENU O This menu is to turn on/off dualstandby. When it is switched to ON, the radio will start standby between A and B including their set parameters. Any channel or frequency has been received,then system will stay on corresponding channel or frequency, until channel or frequency signal disappear. Once signal has disappeared, system will return to standby and start to flicker "TDR". 14 How to operate In standby, press Press and number and the screen will display enter, arrowhead aim at "ON" position, press OFF turn off dualstandby. Press NOTE select ON turn on dualstandby or to confirm, then press to return to standby. Standby time is set by auto-backlight. (See MENU 9) Setting channel step (STEP) ---- MENU 1 In standby, press and number and the screen will display Press enter, arrowhead aim at "5.00" and press Press to confirm, then press to select the channel step you desired. to return to standby. This transceiver has the option of 5KHz, 6.25KHz, 10KHz, 12.5KHz and 25KHz steps. NOTE In frequencymode you have thirteen different settings to choose from channel step, transmit output power, voice encrypt compress, bandwidth,receive CTCSS and DCS, transmit CTCSS and DCS, optional signal, signal encode, mutemode, frequencyshift direction, offsetfrequency on A/B. In channelmode the next setting are not available to change: transmit output power, receive CTCSS and DCS, 15 Professional FM Transceiver NOTE transmit CTCSS and DCS, optional signal, channel bandwidth, encoding signal, mutemode,PTT transmit, voice encrypt compress, busy channellockout, companding and adding channelscan. In channelmode the next three settings are not available to change on A/B segment: channel step, frequencyshift direction, offsetfrequency. In channelmode setting voice encrypt compress is available to change A/B segment. Setting squelch level (SQL-LE ) --- MENU 2 Select the level of squelch so that you will have no difficulty receiving the desired signal. When you set the level too high you will loose communication in a fringe area. NOTE This transceiver has steps from 0-9, which step 0 is always open squelch. From 1 to 9 gives different levels of noise reduction. In standby, press + number and the screen will display Press enter, arrowhead aim at "5" position by going Press to confirm, then press to select the desired squelch. to return to standby. 16 How to operate Setting batterypack savemode (SAVE)--- MENU3 In standby, press + number and the screen will display Press enter, arrowhead aim at "OFF" position, press Press to confirm, then press select one of 1:1/ 1:2/1:3/1:4/OFF. to return to standby. 1:1/1:2/1:3/1:4 means the radio receive circuit turn on and off pulse ratio. Selecting transmitpower (TXP)--- MENU4 In frequencymode, press + number and the screen will display Press enter, arrowhead aim at "1" position, press Press to confirm, then press NOTE and select the desired powerlevel. to return to standby. This transmitpower has 10 levels can be selected, this means it will higher and higher from 1 to 10. High/Low power can be changed during transmit. Press PTT key and topkey at the same time, this will change High/Low power. 17 Professional FM Transceiver Setting voice encrypt compress (SCR)--- MENU 5 SCR: Use the scrambler, it can encrypt the communication and make the transceiver who does not use the scrambler can't hear clear what you are talking, meanwhile you also can't hear clear others, what they are talking who does not use the scrambler. In standby, press Press + number and the screen will display enter, arrowhead aim at "OFF" position, press function or ON to turn on SCR. Press NOTE to confirm, then press and select OFF to switch off this to return to standby. To ensure effective communications the radio's must be set to the same voice encrypt. Transmit over timer (TOT) ---- MENU 6 The TOT is designed to prevent your radio to transmit too long. When the transceiver is exceeding the preset time limit it will stop transmitting and give you a warning signal. This transceiver can be set in 40 steps of 15 seconds, between 15 and 600 seconds. In standby, press and the screen will display Press enter, arrowhead aim at "60" and press Press to confirm, then press to select the level you need when on transmit. to return to standby. 18 How to operate Setting VOX (VOX) ---- MENU 7 In standby, press Press + number and the screen will display enter, arrowhead aim at "OFF" position, press the 1 to 10 different sensitivity-levels. Press NOTE to select VOX OFF or to switch on to confirm, then press to return to standby. When level is too high the VOX needs more volume to get activated. When scan or radio is in using, you can not use VOX function. Setting wide and narrow bandwidth (WN) ---- MENU 8 In standby, press Press + number and the screen will display enter, arrowhead aim at "WIDE" position , press NARROW bandwidth. Press to confirm, then press and you can select WIDE or to return to standby. Setting auto backlight (ABR) ---- MENU 9 It means that the time of return to radio standby state after receive the signal. In standby, press Press +number ABR and the screen will display enter, arrowhead aim at "2" position, press key and select 1 to 5 to turn on auto 19 Professional FM Transceiver backlight or when you want to switch OFF backlight. Press to confirm, then press to return to standby. NOTE Time of auto backlight of this transceiver has 5 levels of which 1 second difference. Setting receive CTCSS (R-CTCS) ---- MENU 10 Sometimes may be you only want to hear the calling which comes from the specific individual or group, then you can ignore some(can not hear from others who using the same frequency) calling through CTCSS/DCS. Only when receive the same signal of CTCSS/DCS, the radio will release the mutemode. In standby, press Press + number and the screen will display enter, arrowhead aim at "OFF" position, press or use one of the tones between 67Hz and 254.1Hz. Press and select OFF to switch off CTCSS and confirm, then press to return to standby. NOTE This transceiver has 50 groups different CTCSS tones, see appendix (1) CTCSS frequency sheet. 20 How to operate Setting receive DCS (R-DCS) ---- MENU 11 In frequencymode, press Press + number and the screen will display enter, arrowhead aim at "OFF" position, press one of the steps from D023N to D754I. Press NOTE and select OFF to switch off DCS or to confirm, then press to return to standby. This transceiver has 105 groups different DCS codes, see appendix (2) DCS frequency sheet. And DxxxN means positive code, DxxxI means negative code. The range of positive code is between D023N and D754N, negative code is between D023I and D754I. Setting transmit CTCSS (T-CTCS) ---- MENU 12 In standby, press Press + number and the screen will display enter, arrowhead aim at "OFF" position, press or use one of the tones between 67Hz and 254.1Hz. Press and select OFF to switch off CTCSS to confirm, then press to return to standby. NOTE This transceiver has 50 groups different CTCSS tones, see appendix (1) CTCSS frequency sheet. 21 Professional FM Transceiver Setting transmit DCS (T-DCS) ---- MENU 13 In frequencymode, press Press + number and the screen will display enter, arrowhead aim at "OFF" position, press one of the steps from D023N to D754I. Press NOTE and select OFF to switch off DCS or to confirm, then press to return to standby. This transceiver has 105 groups different DCS codes, see appendix (2) DCS frequency sheet. And DxxxN means positive code, DxxxI means negative code. The range of positive code is between D023N and D754N, negative code is between D023I and D754I. Setting voiceguide (VOICE) ---- MENU 14 In standby, press Press + number and the screen will display enter, arrowhead aim at "ENG", press off the voiceguide. Press NOTE to confirm, then press key to either select English or OFF to switch to return to standby. If want to turn off all keypad voiceguide should turn off MENU15 and MENU14. 22 How to operate Setting beepprompt function (BEEP) ---- MENU 15 Beepprompt is to tell you if the transceiver is operating well or has a malfunction. We kindly advice you to switch on this function. This function will inform you for any possible malfunction. In standby, press Press + number and the screen will display enter, arrowhead aim at "ON" then press want to switch off the beep. Press NOTE to switch on the beep or OFF when you to confirm, then press to return to standby. When MENU 14 is switched on, the voice guide gets priority. Setting DTMF sidetone (DTMFST) ---- MENU 16 DTMF sidetone gives you the opportunity to switch on or off the speaker when transmit DTMF. The transceiver has 4 different options. KEY: Switch on sidekey when transmitting. ANI: Switch on the ANI sidetone when transmitting. BOTH: Sidekey and ANI are both on. OFF: Turn off all. 23 Professional FM Transceiver In standby, press Press + number and the screen will display enter, arrowhead aim at "BOTH" position, press ANI/BOTH/OFF. Press to confirm, then press and select one function of KEY/ to return to standby. Setting transmit overtime alarm (TOA) ---- MENU 17 Transmit overtime alarm is the setting to alarm the user that he/she has reached the preset time and a voiceprompt and light will flicker during transmit. The transceiver can be set from 1 to 10 TOA in steps of 1 second. In standby, press Press + number and the screen will display enter, arrowhead aim at "5" position, press overtime alarm. Press to confirm, then press to select OFF or to set 1 to 10 for the to return to standby. Busy channel lockout (BCL) ---- MENU 18 This function is to prevent that interfere others who is on communicating. If the channel you have selected which is using by other radio, at this time press PTT key, you can not transmit. In frequencymode, press + number and the screen will display Press enter, arrowhead aim at "OFF" position, press Press to confirm, then press and select between ON or OFF. to return to standby. 24 How to operate Adding channelscan (SC-ADD) ---- MENU 19 This function ensure that whether frequency or channel be added to scan list or not. In frequencymode, press + number ABR and the screen will display Press enter, arrowhead aim at "ON" position, press Press to confirm, then press and select ON or OFF. to return to standby. Priority scan function (PRI-SC) ---- MENU 20 When the transceiver is in non-priority frequencymode, it still check activity of the priority channel, once there has an action at priority channel, the transceiver will auto work in the priority channel. In frequencymode, press + number and the screen will display Press enter, arrowhead aim at "OFF" position, press Press to confirm, then press to turn on or turn off. to return to standby. 25 Professional FM Transceiver Setting priority channel scan function (PRI-CH) ---- MENU 21 This function means any channel which has been programmed can be set as priority scan channel. In frequencymode, press + number and the screen will display Press enter, arrowhead aim at "CH-000" position, press Press to confirm, then press NOTE select the desired channel. to return to standby. This transceiver priority scan channel from 0 to 199 can selectable. There is only dispaly a "S" on LCD screen, that means radio has startup priority channel scan. Startup priority channel scan function needs two conditions: 1. Do priority channel scan switch on. 2. This function scan the channel which has been stored. In frequencymode, channelmode or scanning, when transceiver detects a signal, it will transfer the priority channel, after the signal disappeared 3 seconds if you don't do any operation, transceiver will back to frequency and go on priority scan. The speed of startup or resume priority scan is relative to the setting backlight. When if the backlight be set as "1", then the speed of startup or resume priority scan will be the fastest. When the priority channel which has been set parameter receive signal, if with the same frequency, then radio can transfer the priority channel. The transfered priority channel only be used to communcation, you can't do any other operation until radio resumes frequency. 26 How to operate Setting scanmode (SC-REV) ---- MENU 22 This transceiver will stop scanning when detect the frequency(memory channel) of signal.According to the method of restoring that you choose,the transceiver will resume or stop scanning. The transceiver has three scanmodes. TO: After signal in channel disappears the transceiver will start scanning if without any operation within 5 seconds. CO: After the transceiver stopped on a signal it will resume scanning again in 3 seconds when signal disappears. SE: Scanning will stop when receives a signal. In standby, press + number and the screen will display Press enter, arrowhead aim at "TO" position, press Press to confirm, then press Switch on scanning: Press the and select TO, CO or SE. to return to standby. via keyboard. 27 Professional FM Transceiver Setting option signal (OPTSIG) ---- MENU 23 In standby, press Press + number and the screen will display enter, arrowhead aim at "WDTS" position, press /2-TONES/5-TONES, Press to confirm, then press select one kind of WDTS/DTMF to return to standby. All calls, group calls and selective calls This transceiver has the functions of transmitting ANI,editing ANI and DTMF decoding, without by other tool, it can accomplish the operation of all calls, group calls and selective calls. How to program all calls, group calls and selective calls. 1. Program ANI This transceiver has 3 kinds of method: *. ANI-XXX *. ANI-XXXX *. ANI-XXXXX XXX: Means can program 3 bits ANI ID CODE. XXXX: Means can program 4 bits ANI ID CODE. XXXXX: Means can program 5 bits ANI ID CODE. 28 How to operate XXXX Grouplist A unique ANI ID CODE 1 to 9 groups Edit method: see to the MENU 48. NOTE From 0000 to 9999 maximum This is how to build up ANI. Every transceiver in the group needs a unique ANI ID CODE. 2. Setting all calls, group calls and selective calls. NOTE Using any transceiver of group must be set turning on WDTS optional signal. Setting WDTS optional signal, the details see to the MENU 23. 3. Setting mutemode must be set as AND,the details see to the MENU (24) 4. Press PTT: Setting time according your need, the details see to the MENU (25) 5. Turn on ringtime alarm and set ringtime (Set when needed); The details see to the MENU (30) and MENU (31) 6. Setting PTT-LT In fact, you can choose the time of signal delay before transmit. The details see to the MENU (26) 29 Professional FM Transceiver NOTE Every transceiver using in the group must be set the same frequency, channel and parameter. a. Using All calls Press PTT to transmitting, after transmitting ANI ID CODE, input directly by keyboard. b. Using group calls Press PTT to transmitting, after transmitting ANI ID CODE, input [group number] + directly by keyboard (Using three ID codes as an example). c. Using selective calls Press PTT to transmitting, after transmitting ANI ID CODE, input the ANI ID CODE you want to call by keyboard. NOTE This transceiver has ID memory function, after you used all calls, group calls or selective calls, then you want to transmit again, the ID code is the same as last time you transmitted. If you want to transmit new ID code, please press before transmitting. This transceiver has difference of 3,4,5 bit. so all the ANI ID CODE in the group have better set the same bit. When the bit of transmitter is lower than receive's, you can use the to make up, then you can go on all calls, group calls or selective calls. 30 How to operate DTMF, 2-TONES, 5-TONES. 1. When DTMF/2-TONES/5-TONES signaling is programmed in a frequency. Press PTT key to transmit DTMF/2-TONES/5-TONES signal. 2. When DTMF/2-TONES/5-TONES is set in a channel , the preset functions will be activated only when the matching DTMF/2-TONES/5-TONES signals are received. 3. Likewise, your signals will be received only by parties using the same DTMF/2-TONES/5-TONES. 4.Setting signal *Using any one of transceiver must be set DTMF/2-TONES/5-TONES option signal, the details see to the MENU (23). *Setting sidetone the details see to the MENU (16), according your requirement to select. *Mutemode should have set as AND, the details see to the MENU (24) *Setting PTT transmit Depend on your requirement to select one of the BOT/EOT/BOTH, the details see to the MENU (25) *Setting S-INFO The receiver's and the transmitter's signaling must be set the same. *Setting PTT-LT In fact, the signal can delay before transmitted, the details see to the MENU (26) 31 Professional FM Transceiver Setting mutemode (SPMUTE) ---- MENU 24 The mutemode is to turn on/off the speaker audio according to your optional signal setting. This transceiver has three kinds of mode which can be selected. 1. QT: When the transceiver receives a signal and suited CTCSS tone it will switch on the speaker. When transceiver has not be set a CTCSS tone, then receives a signal which can switch on squelch it also can switch on speaker. 2. AND: When the transceiver receives a suited QT and DTMF signal it will switch on the speaker. 3. OR: When the transceiver receives a suited QT or AND signal it will switch on the speaker. In frequencymode, press + number and the screen will display Press enter, arrowhead aim at "QT" position, press Press to confirm, press and select one of QT or AND or OR. to return to standby. PTT ID (PTT-ID) ---- MENU 25 PTT ID means that the method of choosing the transmitting ID code. *BOT: when press the PTT key, then radio transmits the ID code immediately. *EOT: when release the PTT key, then radio transmits the ID code immediately. *BOTH: when press or release the PTT key, then radio transmits the ID code immediately. 32 How to operate *OFF: The radio can’t transmits the ID code when turn off all. In frequency mode, press Press + number and the screen will display key enter, arrowhead aim at “OFF” position, press /OFF. Press to confirm, press select one of BOT/EOT/BOTH to return to standby. Setting ANI ID CODE transmit (PTT-LT) ---- MENU 26 Setting ANI ID CODE on transmit is needed to send ANI everytime when you press your PTT key. 1-30: Permit transmit ANI delayed time from 1 to 30. Unit: 100ms 0: Do not delay to transmit ANI ID CODE In standby, press Press + number and the screen will display enter, arrowhead aim at "5" position, press or OFF to switch off ANI delay transmit. Press NOTE select 1 to 30 for delay transmit ANI to confirm, then press to return to standby. When alarming, if this menu does not be set as "0", but be set one of the number between 1 and 30, then the setting delayed time will be delayed to transmit signalcode and alarmcode. When the frequency has set WDTS/DTMF /2-TONES/5-TONES signals, if this menu does not be set as "0", but be set one of the number between 1 and 30, then the setting delayed time will be delayed to transmit signalcode. 33 Professional FM Transceiver Setting signal information (S-INFO) ---- MENU 27 This function means select information code which be used to program signal. In frequency mode, press + number Press enter, arrowhead aim at "1" position, press Press to confirm, then press and the screen will display select from 1 to 15. to return to standby. Emergency calling type (EMC-TP)---MENU 28 This transceiver has 3 kinds function. 1. ALARM: Field alarm 2. ENI: Distant alarm 3. BOTH: Field + distant alarm In frequency mode, press + number and the screen will display Press key enter, arrowhead aim at “ALARM” position, press Press to confirm, then press NOTE select ALARM/ENI/BOTH to return to standby. In frequencymode or channelmode, only be set as ENI and BOTH, then can use the alarm channel to alarm. In frequencymode or channelmode, if you do not set alarm channel, then it will alarm at the present frequency or channel. 34 How to operate Emergency calling channel (EMC-CH)---MENU 29 Select any channel which have set for emergency calling. In standby mode, press + number ABR and the screen will display Press key enter, arrowhead aim at “CH-000” position, press Press confirm, then press select the desired channel, to return to standby. Select ringmode (RING-M)---MENU 30 Setting calling ring means after the transceiver receive the matching signal, it will be announced from the speaker. This transceiver has 4 kinds ringmode can be selectable. SOUND:Turn on ring BIV: Turn on libration BOTH: Turn on ring and libration OFF: Turn off all. In frequencymode, press Press + number and the screen will display key enter, arrowhead aim at “SOUND” position, press BIV/BOTH/OFF. Press confirm, then press select one of SOUND/ to return to standby. 35 Professional FM Transceiver Setting ringtime(RING-T)---MENU 31 It will switch on the speaker when it is over the preset ring time. In standby, press Press + number and the screen will display enter, arrowhead aim at “0” position, press 0 and 10. Press NOTE to confirm, then press to select the time of the ring between to return to standby. This transceiver has 10 different steps of ringtime of which every step is 1 second difference, this means that 0 will switch off the ring. Edit channelname (CHNAME) ---- MENU 32 1. Channelname can be made up of 26 letters (A to Z), 10 numbers (0 to 9) or (?) (+) (-), with any of the 3 last symbols. 2. Channelname can have a length of maximum of 6 bits or you can edit one of the bits from 1 to 6. 3. When you select the (-) symbol it means that the bit is blank. Edit method 1. Via KG-699E software. 36 How to operate 2. Via keyboard of transceiver. Edit Channelname 1. At least one channel should have been stored. 2. The transceiver should be work in channelmode. 3. Enter the channelname edit menu, then press to select character, press to select edit position. Edit step 1. If the transceiver works in frequencymode, set the workmode as NAME in the display then press and power on again. If the transceiver works in CH mode, then go through MENU 34 to set display to NAME. 2. Select the desired channel, press press and select character then press and then the screen will display 6 rails, , press character, after selecting the sixth character press again to select the second to confirm, press to exit. The screen will display the channelname and show the order of this channel on top right corner. 37 Professional FM Transceiver Setting transmit segment when in dual standby (TDR-AB) ---- MENU 33 The transeiver will transmit on A segment or B segment when switch on the dualfrequency. In frequencymode, press Press and the screen will display enter, arrowhead aim at "A" position, then press confirm, then press NOTE + number selected A or B. Press to to return to standby. Setting this function you must turn on dualstandby at first. When in dualstandby,press PTT to transmit A segment or B segment. Setting A segment channel display mode (CA-MDF)---MENU 34 This transceiver has three selectable display modes: channelorder display, channelfrequency + channelorder display, channelname + channelorder display. In standby, press + number and the screen will display 1. Channelorder display mode Press enter, press Press to confirm, then press select CH and the screen will display to exit. 38 How to operate 2. Channelfrequency + Channelorder display mode Press enter, press select FREQ and the screen will display Press to confirm, then press to exit. 3. Channelname + Channelorder display mode Press enter, press select NAME and the screen will display Press to confirm, then press to exit. Channelname display mode: To operate this function you need to edit the channelname first or it will still display the channelorder. See details of channelname edit in MENU 32. Setting B segment channel display mode (CB-MDF)---MENU 35 This transceiver has three selectable display modes: Channelorder, channelfrequency + channelorder and channelname + channelorder. In standby, press + number and the screen will display 1. Channelorder dispay mode Press enter, press select CH and the screen will display Press to confirm, then press to return to standby. 39 Professional FM Transceiver 2. Channelfrequency + Channelorder display mode Press enter, press Press to confirm, then press selcet FREQ and the screen will display to return to standby. 3. Channelname + Channelorder display mode Press enter, press Press to confirm, then press select NAME and the screen will display to return to standby. Channelname display mode: To operate this function you need to edit the channelname first or it will still display the channelorder. See details of channelname edit in MENU 32. Setting keyboard lock (AUTOLK) ---- MENU36 The transceiver has two options, auto lock and manual lock. AUTOLK: When you set autolock the keyboard will be locked within 15 seconds. To release keyboard press for more than 2 seconds. OFF: Turn off auto lock In frequencymode, press Press + number and the screen will display enter, arrowhead aim at "OFF" position, press OFF to switch off autolock. Press to confirm, then press and select AUTO for autolock or to return to standby.. 40 How to operate NOTE Manual lock: In standby, press # for more than 2 seconds will lock keyboard, release keyboard press # for more than 2 seconds. Setting power on message (PONMSG) ---- MENU 37 Transceiver power on message: FULL: Full display BATT-V: Display the current voltage of batterypack In standby, press Press + number and the screen will display enter, arrowhead aim at "FULL" position, press MSG, Press to confirm, then press MSG: display "Best Wishes" and select one of FULL/BATT-V/ to return to standby. Setting sidekey 1(PF1)---MNEU 38 This transceiver sidekey 1 has 5 kinds function can be selected: 1.FM: FM radio key 2. CALL: Signal calling at present. 3. NO-SUB: Cancel receive DCS or CTCSS. 4. JP-PRI: Switch to priority scan channel. 41 Professional FM Transceiver 5. JP-EMC: Switch to emergency calling mode. 1. Select FM radio function. In standby, press the sidekey 1 to switch on FM radio,this FM radio is frequency modulation, frequency range is 87-108MHz, and the screen will display a. In FM radio, press b. Press or number key to select program. , you can check the working frequency and channel, after 2 seconds the screen will resume , the radio works in normally when you are on operation. c. Press PTT, sidekey 2 and topkey, it will into the relevant operation. When you want to turn off radio, press sidekey 1 again. When you turn on the FM radio, you should install supplied antenna. In standby, press Press +number and the screen will display enter, arrowhead aim at "FM" position, press NO-SUB/JP-PRI/JP-EMC, press NOTE to confirm, press and select one of the FM/CALL/ to return to standby. When in FM radio, the present frequency or channel are still in standby, if transceiver receives a signal,it will return to two-way radio, After the signal disappeared 5 seconds, it will auto return to FM radio. If you want 42 How to operate NOTE to exit FM radio, please press sidedey 1 again. You can use the software to edit the channel of FM radio, make the radio can display the frequency and radio's name on LCD screen, after you have succeed in programming, press the sidekey 1 to turn on FM radio, now you not only can use the channel knob to switch channel, but also can use to switch. If the radio don't have channel knob, you can use to switch FM radio channel. Setting topkey (PF2) ---MENU 39 The topkey offers two kinds of function: EMCALL: Start up alarm function CALL01-CALL15:Signal calling key Select EMCALL function In standby, press Press + number ABR and the screen will display enter, arrowhead aim at “EMCALL”, press confirm, then press and select EMCALL. Press and to return to standby. When you have selected EMCALL, in standby press the topkey and from your speaker an alarm will sound and the red and green lamp will flicker at the same time. Press the topkey again to exit. 43 Professional FM Transceiver Signal calling key In standby, press Press + number and the screen will display enter, arrowhead aim at “EMCALL” position, press CALL01 to CALL15, press NOTE ABR to confirm, then press select one of function from to return to standby. CALL01-CALL15: Means the information code which has been set as calling signal, when PF2 has been set as one kind of CALL01-CALL15, then press PF2 one time, meanwhile the LED A and B flicker each other. When the information code of signal has been set as the same as others and other functions are also the same, then press PTT you can communicate each other, also you can communicate when the LED is flickering. Define MONI key (MONI) ---- MENU 40 This function is defined for squelch diagram. Total have 2 kinds function can be selected. CONTIN: Should always press side key 2 all the time to persist turn off squelch diagram. PRESS: Just need press side key 2 one time to persist turn off squelch diagram. In standby, press + number and the screen display 44 How to operate Press enter, arrowhead aim at “CONTIN” position. Press Press confirm, then press select CONTIN/PRESS to return to standby. Selecting standby display color (WT-LED) ---- MENU 41 The transceiver has four colors available: BLUE / ORANGE / PURPLE/OFF In standby, press Press + number and the screen will display enter, arrowhead aim at "PURPLE" position, press BLUE / ORANGE / PURPLE/OFF. Press and select the desired color of to confirm, then press to return to standby. Selecting receive display color (RX-LED) ---- MENU 42 The transceiver has four colors available: BLUE / ORANGE / PURPLE/OFF. In standby, press Press + number and the screen will display enter, arrowhead aim at "BLUE" position, press BLUE / ORANGE / PURPLE/OFF. Press and select the desired color of to confirm, then press to return to standby. 45 Professional FM Transceiver Selecting transmit display color (TX-LED) ---- MENU 43 The transceiver has four colors available: BLUE / ORANGE / PURPLE/OFF In standby, press Press + number and the screen will display enter, arrowhead aim at "ORANGE" position, press BLUE / ORANGE / PURPLE/OFF. Press to confirm, then press and select the desired color of to return to standby. Setting memory channel=setting co-channel and dis-channel (MEM-CH) ---MENU 44 When transceiver works in frequencymode or in standby, input the frequency and any kind of parameter what you want to store. Press + number Press enter, press and the screen will display to select channel order, press to store and you will hear a voiceprompt if it is stored. Press to exit, at this moment the channel should be co-channel frequency channel. When you need to store dis-channel, repeat the above procedure, after you stored, you will hear a voiceprompt "store transmit". 46 How to operate Example: You want 450.025MHz for receive and 460.025MHz for transmit and stored in CH-20, then act as follows: 1. When the transceiver works in frequency mode, input , then press or voice prompt will tell you it is stored, press 2. Then input will tell you it is stored + press key select CH-20, press key to confirm, to exit; and voiceprompt to exit. 3. The dis-channel is stored. NOTE If you want to set CTCSS, D.C.S, W&N etc functions on parameter please setting before stored. Then it can store with frequency in channel. The transmitting only stored transmit frequency, if you want to store MENU function and parameter, please store with the receiving. If you want to store by manual, in frequencymode, and the channel should be vacant, then you can go on operation of store receiving and transmitting or you can only go on the operation of storing transmitting. If the channel is not vacant and you want to go on the operation of storing receiving and transmitting, you should delete channel. 47 Professional FM Transceiver Delete channel (DEL-CH) ---- MENU 45 In standby, press Press + number enter, press and the screen will display to select the channel you want to delete, press The select channel and message are deleted, press to confirm. to return to standby. Setting frequencyshift direction (SFT-D) ---- MENU 46 Frequencyshift means that: 1. The transmit frequency is higher than receive frequency. This is called positive offset (+) 2. The transmit frequency is lower than receive frequency. This is called negative offset.(-) 3. Turn off frequencyshift. In standby, press Press enter, press + number and the screen will display and select one of +/-/OFF. Press to confirm, then press to return to standby. Setting offsetfrequency (OFF-SET) ---- MENU 47 Offsetfrequency is the difference between the transmit and receive frequency. The transceiver offset range can be from 0 to 99.950MHz. 48 How to operate In standby press Press + number and the screen will display enter, press number 0 to 9 to select offsetfrequency. Press to confirm, then press to return to standby. The frequencyshift direction and offsetfrequency can only be programmed when the transceiver works in frequencymode, in order to let transmitting and receiving under different frequency. Follow the next steps: 1. Set working frequency. 2. Set frequencyshift direction and offsetfrequency. Example: In frequencymode, the transceiver will work on receive frequency 450.025MHz and transmit frequency will be 460.025MHz. In frequencymode, order input and select positive offset (+); press to select 10.000+ , then press , press + numberkey and the frequencyshift direction plus offsetfrequency are complete. The screen will display 49 Professional FM Transceiver When press PTT key the screen will display When you release PTT the screen will display Now the receiving frequency is The transmit frequency is ANI CODE edit (ANI) ---- MENU 48 Any transceiver of group must edit different ANI code. NOTE Because this transceiver has different of 3 bits, 4 bits and 5 bits, so the length of ANI CODE must keep the same as which used in group. ANI CODE only can be programmed via KG-699E programming software. Setting VOX-T (VOXT) ---- MENU 50 The purpose of setting VOX-T is to avoided the problem: When after transmitted, transceiver will return to receivedmode immediately, but you can't ensure whether last part of calling can be transmitted or not, so you can set a proper VOX-T then makes calling can be transmitted exactly. 50 How to operate Be careful, don't set VOX-T to a long time. This transceiver total has 20 levels, unit: 100ms In standby, press Press +number and the screen will display enter, arrowhead aim at "5", press not allow delay transmit, press and select one of level between 1 and 20 or 0 to confirm, then press to return to standby. Companding (COMP) ---- MENU 51 COMP: Use voice compress technology to reduce the noise when on talking, make the voice clear. In standby, press + number and the screen will display Press enter, arrowhead aim at "OFF" position, press Press to confirm, then press to select ON or OFF. to return to standby. Setting reset (RESET) ---- MENU 52 The transceiver has a menu which resets VFO and ALL messages. When you use RESET VFO all parameters of menu will return to factory default. When you use RESET ALL all menu and channel parameters will return to factory default. 51 Professional FM Transceiver 1. MENU reset (VFO): In standby, press + number Press enter, press Press again and the screen will display and the screen will display select VFO, press key and the screen will display When the reset has worked well the transceiver will auto power off and auto switch on again. 2. All message reset (ALL): In standby, press + number Press enter, press Press again and the screen will display the screen will display and select ALL, press and the screen will display When reset has worked well, the transceiver will auto power off and auto switch on again. Setting reverse frequency function When using reverse frequency function, the transceiver transmit-and receivefreuency will interchange and the setting of CTCSS and/or DCS encode and decode will interchange. Operating reverse frequency function: In standby, press T- R SCAN and this will turn on reverse frequency function, press T- R SCAN again and this will turn off reverse frequency function. 52 How to operate Lowvoltage batterypack voiceprompt When the batterypack has lowvoltage, the transceiver will sound "low batterypack"voice prompt. Setting transmit overtime prompt When transmitter works longer than preset time, the transceiver will announce "transmit overtime" by voice and stops transmitting. If you want to transmit again, please press PTT. (Setting overtime prompt please see MENU 6) Adding channelscan Edit method: Strictly via KG-699E programming software. Only scan according programming list which have added channel scan on programming software. Wireclone function Using wireclone Switch sourceradio on,after you have connected the targetradio to the sourceradio via the cloningcable,push the [MONI] key and the sourceradio starts cloning. LED is flashing red during cloning. LED goes out in case of successful cloning. LED glows continuous red in case of cloning failure. LED is flashing green during cloning. LED will switch OFF when cloning complete. Targetradio 53 Professional FM Transceiver Programming repeater function Most repeaters use standard or different splits and/or matching CTCSS/DCS or DTMF signals. When you need to join a repeater, you need to set different parameters on receive and transmit. Example: The repeater transmit frequency is 450.025MHz, CTCSS value is 67Hz, the receive frequency is 460.025MHz, CTCSS value is 254.1Hz. When the transceiver needs to join the repeater, you need to follow the following steps: 1. Set receive frequency, CTCSS value and transmitting CTCSS value and store this on appointed channel, example channel 20. The transceiver in frequencymode, setting receive frequency is 460.025MHz, receiving CTCSS value is 254.1 Hz, transmitting CTCSS vallue is 67Hz, and store to channel 20. The operation is as follows: In frequencymode, order input , press press and select CTCSS value 254.1 + and select CTCSS value 67Hz + voice prompt receive store, press key. 2. Setting transmitfrequency and store in appoint channel 20. The transceiver in frequencymode, setting transmitfrequency as 450.025MHz, and store in channel 20. 54 How to operate In frequencymode, order input 3. Press press . Voiceprompt transmit store, press key. , turn on the power at the same time, the transceiver work in channel mode at this time, select channel 20, the transceiver can join repeater. How to use your intelligentcharger 1. When the poweradapter is connected the intelligentcharger, the poweradapter should be plugged into the matchingvoltage. The intelligentcharger will flicker once, then go into the standby mode which means that you can charge the batterypack; When you plug in the batterypack, the intelligentcharger will switch to red LED which means that it has being charged. 2. When the green light flickers, the batterypack is fully charged. 3. After you plug in the batterypack which the voltage is lower than 6V (it is lower than 6V if you can not power on the transceiver), the red LED flickers which means that the batterypack is being trickle charged by intelligentcharger and this will last about 10 minutes. When the light turns red, it will go into the normal charge. 4. After you plug in the batterypack which the voltage is higher than 6V(it is higher than 6 V if you can power on the transceiver), the red LED flickers, at this time, please confirm whether the batterypack is plugged in right with intelligentcharger. 55 Trouble shooting Professional FM Transceiver Please check carefully if your transceiver has problems by following this chart. If you maintain to have trouble you can reset your transceiver and very often this will eliminate your problem. Problem Transceiver will not switch on. Possible Cause Possible Solution 1. The batterypack is not adjust properly. 1. Re-install the batterypack. 2. The batterypack maybe exhausted. 2. Charge the batterypack. 3. The batterypack is getting too old. 3. Change the batterypack. The receiverlight is 1. The powerswitch is not adjusted well. on and there is no 2. Confirm if your CTCSS/DCS or DTMF sound from the speaker. tone is the same as others. 3. Confirm if you use the right mutemode. 1. Turn the volumecontrol. 2. Reset the CTCSS/DCS. 3. Reset the mutemode. 1. Check if you have installed your antenna 1. Install the supplied antenna. 2. Move the radio around till you receive the desired signal or press There is no reception 2. The signal you are receiving is very weak. to reset and press again to go to the right channel. right. 56 Trouble shooting Problem Possible Cause Possible Solution Keyboard and PTT 1. The keyboard is locked. 1. Set keyboard to free. switch do not work. 2. RADIO "mode" is switched on, see displayFM. 2. Please exit RADIO mode. If you have set transceiver to busychannel Switch off busychannel lockout. lockout. You can not store In channel mode or frequency+channel Set transceiver to frequency certain settings. mode you cannot set parameters. mode. The receivelight is on and you can not transmit. Autotransmit when Switch off VOX or set VOX to The VOX level is set too LOW. you are in standby. a HIGHER level. During communication you receive other The frequency and the CTCSS/DCS are Change the setting of CTCSS/ group(s) or receive the same as other users. DCS,frequency or channel. distorted signal. 57 Technology parameter Professional FM Transceiver Appendix 1 CTCSS 67.0 11 94.8 21 131.8 31 171.3 41 203.5 69.3 12 97.4 22 136.5 32 173.8 42 206.5 71.9 13 100.0 23 141.3 33 177.3 43 210.7 74.4 14 103.5 24 146.2 34 179.9 44 218.1 77.0 15 107.2 25 151.4 35 183.5 45 225.7 79.7 16 110.9 26 156.7 36 186.2 46 229.1 82.5 17 114.8 27 159.8 37 189.9 47 233.6 85.4 18 118.8 28 162.2 38 192.8 48 241.8 88.5 19 123.0 29 165.5 39 196.6 49 250.3 10 91.5 20 127.3 30 167.9 40 199.5 50 254.1 58 Technology parameter Appendix 2 DCS D023N 16 D074N 31 D165N 46 D261N 61 D356N D025N 17 D114N 32 D172N 47 D263N 62 D364N D026N 18 D115N 33 D174N 48 D265N 63 D365N D031N 19 D116N 34 D205N 49 D266N 64 D371N D032N 20 D122N 35 D212N 50 D271N 65 D411N D036N 21 D125N 36 D223N 51 D274N 66 D412N D043N 22 D131N 37 D225N 52 D306N 67 D413N D047N 23 D132N 38 D226N 53 D311N 68 D423N D051N 24 D134N 39 D243N 54 D315N 69 D431N 10 D053N 25 D143N 40 D244N 55 D325N 70 D432N 11 D054N 26 D145N 41 D245N 56 D331N 71 D445N 12 D065N 27 D152N 42 D246N 57 D332N 72 D446N 13 D071N 28 D155N 43 D251N 58 D343N 73 D452N 14 D072N 29 D156N 44 D252N 59 D346N 74 D454N 15 D073N 30 D162N 45 D255N 60 D351N 75 D455N 59 Professional FM Transceiver DCS 76 D462N 82 D516N 88 D606N 94 D645N 100 D723N 77 D464N 83 D523N 89 D612N 95 D654N 101 D731N 78 D465N 84 D526N 90 D624N 96 D662N 102 D732N 79 D466N 85 D532N 91 D627N 97 D664N 103 D734N 80 D503N 86 D546N 92 D631N 98 D703N 104 D743N 81 D506N 87 D565N 93 D632N 99 D712N 105 D754N 60 Technology specification Frequencyrange Memorychannels Voltage Working temperature Channels Poweroutput Mode Maximum deviation Adjacent channel power Stability Sensitivity Audio output power Weight Size NOTE UHF: 406.125-469.975MHz 200 channels 7.4V DC -30*(-22F) to +60*(140F) Co-channel or Dis-channel simplex UHF:4W F3E(FM) * ±5KHz < -60dB ±5 ppm < 0.2 µV *700mW 250g 62 X 105 X 39 (mm) 2.44x4.13x1.54(inch) Specifications are subject to change without notice. 61 Optional accessories Professional FM Transceiver Dual slot charger Wireclonecable "AA" batterypack Headset Eliminator Speaker/MIC Programmingcable Carcharger 1700mAh Li-ion Programming Switching adapter batterypack Software 62 Announce endeavors to achieve the accuracy and completeness of this manual,but is not liable for any possible omission and printing errors.All the above specifications are subject to change by without prior notice. English Version:699E-A-0811-V1 63
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 38EXIF Metadata provided by EXIF.tools