R tron SNIDEN25 iDen Mini Wireless Repeater User Manual

R-tron Inc. iDen Mini Wireless Repeater

Contents

Part 1

iDEN MINI (RSN-iDEN-25) User’s Manual R-tron Inc.
User’s Manual -2- RF EXPOSURE INFORMATION A minimum separation distance of 7.9 inches(20cm) must be maintained between the user and the external antenna of repeater to satisfy FCC RF exposure requirements. For more information about RF exposure, please visit the FCC website at www.fcc.gov CAUTION This equipment is indoor use and all the communication wiring are limited to inside of the building.
iDEN MINI User’s Manual -3- This document describes the specifications, installation and operation of iDEN MINI. Hardware and software mentioned in this document are subject to continuous development and improvement. Consequently, there may be minor discrepancies between the information in the document and the performance and design of the product. Specifications, dimensions and other statements mentioned in this document are subject to change without notice. R-tron Inc. 6402 College Boulevard Overland Park, KS 66211 Phone: +1-913-344-9977, 1-888-31R-TRON, Fax: +1-913-344-9988, Internet: www.r-tron.com R-tron is registered trademarks of R-tron Inc. Other products and company names mentioned herein this manual might be trade marks or trade names of their respective owners. This document or parts of it may not be reproduced without the written permission of R-tron Inc. Infringements will be prosecuted. All rights reserved Copyright © R-tron Inc. 2000-2007
iDEN MINI User’s Manual -4- Contents Abbreviations ....................................................................................................................... 6 1. Introduction ........................................................................................................... 7 2. Description ............................................................................................................. 9 2.1 System Specifications ....................................................................................................... 9 2.1.1. Electrical Specifications .......................................................................................... 9 2.1.2. Mechanical Specifications .................................................................................... 10 2.2 Sub Unit Overview ............................................................................................................ 11 2.2.1. Block Diagram ...................................................................................................... 12 2.2.2. UDC Module ......................................................................................................... 13 2.2.3. Multiplexer ............................................................................................................ 14 2.2.4. MCU (Main Control Unit) ...................................................................................... 15 2.2.5. Power Supply ....................................................................................................... 16 2.2.6. HPA (High Power Amplifier) .................................................................................. 17 3. Hardware Installation............................................................................................ 18 3.1 Check List of Items .......................................................................................................... 18 3.2 Mounting .......................................................................................................................... 19 3.3 Grounding ........................................................................................................................ 20 3.4 RF Cable Connection ...................................................................................................... 20 3.5 Power Up ......................................................................................................................... 21 4. Command and Control through the Hyper Terminal ................................................ 22 4.1 Setting for Command and Control through the Hyper Terminal ........................................... 22 4.2 Command and Control through the Hyper Terminal ............................................................ 25 5. Troubleshooting .................................................................................................... 30 5.1 RF Connection Check ..................................................................................................... 30 5.2 Power Connection ........................................................................................................... 30 5.3 Red Light on the Alarm LED ............................................................................................ 31
iDEN MINI User’s Manual -5- Figures Figure 1. R-tron iDEN MINI ...................................................................................................... 7 Figure 2. Overview: Service ..................................................................................................... 8 Figure 3. Dimension of iDEN MINI .......................................................................................... 10 Figure 4. Internal View of iDEN MINI ...................................................................................... 11 Figure 5. Block Diagram ........................................................................................................ 12 Figure 6. UDC Module ........................................................................................................... 13 Figure 7. Multiplexer ............................................................................................................. 14 Figure 8. Main Control Unit .................................................................................................... 15 Figure 9. Power Supply .......................................................................................................... 16 Figure 10. HPA(High Power Amplifier) ................................................................................... 17 Figure 11. Items .................................................................................................................. 18 Figure 12. Mounting ............................................................................................................ 19 Figure 13. Grounding ........................................................................................................... 20 Figure 14. Configuration: RF Cable Connection ...................................................................... 21 Figure 15. Power Cord Connection ........................................................................................ 21 Figure 16. Local connection to the iDEN MINI ....................................................................... 22 Figure 17. LEDs Off ............................................................................................................. 30 Figure 18. AC power cord Check ........................................................................................... 31 Figure 19. Red Light on Alarm LED ....................................................................................... 31
iDEN MINI User’s Manual -6- Abbreviations Abbreviations used in this manual, in iDEN Add-On Filter Box. AC Alternating Current ANT Antenna CDMA Code Division Multiple Access DC Direct Current GND Grounding GUI Graphic User Interface iDEN Integrated Digital Enhanced Network LED Light Emitting Diode PSU Power Supply Unit RF Radio Frequency TEMP Temperature VSWR Voltage Standing Wave Ratio
iDEN MINI User’s Manual -7- 1. Introduction Figure 1. R-tron iDEN MINI iDEN MINI repeater is used to fill out areas in iDEN mobile systems, such as base station fringe areas, business and industrial buildings, etc. iDEN MINI receives signals from a base station, amplifies and retransmits the signals to mobile stations. Also it receives, amplifies and retransmits signals in the opposite direction. Both directions are served simultaneously with the following features:  7MHz or 18MHz-bandwidth service @ 800MHz’s  5MHz-bandwidth service @ 900MHz’s  Band Shifting @ 800MHz’s and 900MHz’s  Roll Offs: 65 dBc at 0.5 MHz outside pass-band AC Power Socket & Switch RJ-45 (network) jack Status LEDsGround rodDonor Antenna Port Service Antenna Port
iDEN MINI User’s Manual -8- . Figure 2. Overview: Service
iDEN MINI User’s Manual -9- 2. Description 2.1 System Specifications 2.1.1. Electrical Specifications Parameter iDEN 800 iDEN 900 Selectable Bandwidth DL & UL In-band BW:18M In-band BW:7.0M In-band BW:5M Frequency Selection DL 18MHz-bandwidth851~869MHz 850.8~868.8MHz 850.6~868.6MHz 7MHz-bandwidth862~869MHz 861.8~868.8MHz 861.6~868.6MHz 5MHz-bandwidth 935~940MHz 934.8~939.8MHz 934.6~939.6MHz UL 18MHz-bandwidth806~824MHz 805.8~823.8MHz 805.6~823.6MHz 7MHz-bandwidth817~824MHz 816.8~823.8MHz 816.6~823.6MHz 5MHz-bandwidth 896~901MHz 895.8~900.8MHz 895.6~900.6MHz Roll off DL & UL ≤65dBc @Fedge+/-500KHz≤65dBc @Fedge+/-500KHz Gain ripple ±1.5dB (Typical) Gain DL & UL 40dB to 65dB Output Power DL & UL 25dBm Delay DL & UL 8.0µs Max. VSWR DL & UL 1.5Max. Rx Noise Figure 5dB Max. (65dB Gain) 12dB Max. (40dB Gain) Input Range DL & UL -30dBm Max. Power supply 110V~125V, 60Hz typical Operating temperature *-10℃~ 50℃ Storage temperature -20℃~60℃ Consumption power ≤94W
iDEN MINI User’s Manual -10- 2.1.2. Mechanical Specifications Parameter Specification RF connectors N-female x 2, SMA-female x 4 Size 18.9 X13.78 X 7.22(Inch), 480 X 350 X 183.5(mm) Weight 24kg (52.912lbs) SERVICEANTENNADONORANTENNA110 -125V ~DANGERRISK OF ELECTRIC SHOCKAC IN 800MHzTX MON.900MHzTX MON.800MHzRX MON.900MHzRX MON. LANALARME25810931CYI.T.Enot cause harmful interference.:MAKER POWER :FCC REG. NO. : SERIAL NO. / DATE : R-tron lnc.COMPLIES WITH PART 96, FCC RULES.110V ~ , 50/60Hz , 2ARSP-AID-001 :MODEL Operation is subject to the condition that this deviceThis devic e comp lies w ith pa rt 15 of the FCC rules.MADE IN KOREA Figure 3. Dimension of iDEN MINI
iDEN MINI User’s Manual -11- 2.2 Sub Unit Overview iDEN MINI is composed of the following sub units:  UDC(Up Down Converter)  HPAs(High Power Amplifiers)  Multiplexer  Main Control Unit (MCU)  Power Supply Unit (PSU)  EMI Filter Figure 4. Internal View of iDEN MINI
iDEN MINI User’s Manual -12- 2.2.1. Block Diagram The following, Figure 5, explains how the iDEN MINI serves signals. Figure 5. Block Diagram
iDEN MINI User’s Manual -13- 2.2.2. UDC Module The UDC Module is basically a bi-directional amplifier that sharply filters out unwanted noise. Figure 6. UDC Module
iDEN MINI User’s Manual -14- 2.2.3. Multiplexer A multiplexer is a device that combines two or more signals onto a common channel or medium to increase its transmission efficiency. Figure 7. Multiplexer
iDEN MINI User’s Manual -15- 2.2.4. MCU (Main Control Unit) MCU is the control unit of iDEN MINI. It controls and monitors operational parameters. It also generates alarms, an event log and many other functions of the iDEN MINI. Figure 8. Main Control Unit Pin Map Port Connected to J1 MCU Vcc(+6V) J3 USB Port(Manufacturer use only) J4 PSU Alarms J5 Door Alarm J6 Status LEDs J7 iDEN 800 PLL,B/S,OUT DET J8 iDEN 900 PLL,B/S,OUT DET J9 Tx HPA J10 Rx HPA J11 RJ-45 jack
iDEN MINI User’s Manual -16- 2.2.5. Power Supply The Power Supply Unit (PSU) supplies a steady DC power to iDEN MINI by drawing power from the general in-wall AC outlets Figure 9. Power Supply Specifications Item Specifications Environmental Operating Temp -10℃~50℃ Humidity 20%~90%RH Cooling method Natural air Voltage AC110~125V Current 5A Max / 6V, 12V, 27VDC Frequency 50~60Hz typ Leakage Current 0.5mA max.@110V AC

Navigation menu