RADIOLAND TECHNOLOGY CC2640S1 BLE Wireless Module User Manual RL CC254x S1

Download:
Mirror Download [FCC.gov]
Document ID	3589108
Application ID	4emih4NddJabrwXjt0xssQ==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	49.06kB (613215 bits)
Date Submitted	2017-10-01 00:00:00
Date Available	2017-10-01 00:00:00
Creation Date	2015-10-09 11:06:45
Document Lastmod	2017-09-26 11:56:54
Document Title	RL-CC254x-S1
Document Creator	WPS Office
Document Author:	ThinkPad

CC2640S1
Overview
Radioland would like to announce a low-cost and low-power consumption module which has all of
the Bluetooth Smart 4.1 functionalities. The CC2640S1 module fully supports the single mode
Bluetooth Low Energy operation, and the output power can support class 2. The module provides
the ability to either put your entire application into the integrated ARM Cortex M3 microcontroller,
or use the module in Network Processor mode in conjunction with the microcontroller of your choice.
RF Core’s dedicated ARM Cortex M0 improves system performance and frees up FLASH memory
for custom applications.
Feature



Built in CC2650F128 Bluetooth Smart
(BLE 4.1) System-On-Chip (SOC)
128 kB Flash / 20 kB SRAM







RF Receive Sensitivity: -96 dBm
Size: 11.8mm x 15.8mm
Operating Voltage: 1.8V to 3.8V
Operating Temperature: -40 to +85C
8.4 mA Transmit Mode
7.4 mA Receive Mode
1μA Standby (SRAM/CPU retention and
RTC running) with quick 100 μs start up
200nA Shutdown
61μA/MHz Active CPU Current
Drivers, Bluetooth Low Energy
Controller, and bootloader in ROM
Flexible peripheral set
On board 32 kHZ and 24 MHz Crystals
Worldwide Acceptance:







Applications








Consumer electronics
Mobile phone accessories
Sports & Fitness equipment
HID applications
Home and Building Automation, Lighting
Control, Alarm and Security
Electronic Shelf Labeling, Proximity
Tags
5F.BlockA2 | Hangcheng Industry Zone | ChenTian | Xixiang Town | Bao’an district | Shenzhen,P.R.C
Tel:+86 0755 66621530 |
www.radioland-china.com | sales@radioland-china.com
Electrical Characteristics
ITEM
TEST REQUIREMENT
Voltage supply
1.8－3.8V
DC
Center frequency
2402－2480MHz
Programmable
Frequency error
±50KHz
Modulation
O-QPSK
Receiving sensitivity
-97dBm
Receiving current
5.9mA
Transmitting current
9.1mA
Sleep consumption At
1uA
power mode2
Sleep consumption At
0.1uA
power mode3
Transmit distance
>60M
Antenna
50ohm
Module size
11.8mm*15.8mm
REMARKS
High gain Mode
TX Power 5dBm
Sleep Timer ON
External interrupts
BER<0.1%
RECOMMENDED OPERATING CONDITIONS
Operating ambient temperature range, TA
Operating supply voltage
MIN
-30
1.8
MAX
85
3.8
UNIT
°C
CAUTION:
ESD sensitive device. Precautions should be used when handing the device in order to prevent
permanent damage.
5F.BlockA2 | Hangcheng Industry Zone | ChenTian | Xixiang Town | Bao’an district | Shenzhen,P.R.C
Tel:+86 0755 66621530 |
www.radioland-china.com | sales@radioland-china.com
RL-CC2640-S1
Dimensions
Pin Assignment
36
13
24
14
23
5F.BlockA2 | Hangcheng Industry Zone | ChenTian | Xixiang Town | Bao’an district | Shenzhen,P.R.C
Tel:+86 0755 66621530 |
www.radioland-china.com | sales@radioland-china.com
RL-CC2640-S1
Pin Num.
Pin Name
Pin Type
Description
VDDS
Power
1.8 V to 3.8 V GPIO supply(1)
GND
Ground
ground
VDD_EB
Power
1.8 V to 3.8 V main chip supply(1)
DIO_0
Digital I/O
GPIO, Sensor Controller
DIO_1
Digital I/O
GPIO, Sensor Controller
DIO_2
Digital I/O
DIO_3
Digital I/O
DIO_4
Digital I/O
DIO_5
Digital I/O
GPIO, High drive capability, JTAG_TDO
10
GND
Ground
ground
11
VDD_EB
Power
1.8 V to 3.8 V main chip supply(1)
12
JTAG_TCK
Digital I/O
JTAG TCKC
13
JTAG_TMS
Digital I/O
JTAG TMSC, High drive capability
14
nREST
Digital input
Reset, active-low. No internal pullup
15
DIO_7
Digital/Analog I/O
GPIO, Sensor Controller, Analog
16
DIO_8
Digital/Analog I/O
GPIO, Sensor Controller, Analog
17
DIO_9
Digital/Analog I/O
GPIO, Sensor Controller, Analog
18
DIO_10
Digital/Analog I/O
GPIO, Sensor Controller, Analog
19
DIO_11
Digital/Analog I/O
GPIO, Sensor Controller, Analog
20
DIO_12
Digital/Analog I/O
GPIO, Sensor Controller, Analog
21
DIO_13
Digital/Analog I/O
GPIO, Sensor Controller, Analog
22
DIO_14
Digital/Analog I/O
GPIO, Sensor Controller, Analog
23
nREST
Digital input
Reset, active-low. No internal pullup
GPIO, Sensor Controller, High drive
capability
GPIO, Sensor Controller, High drive
capability
GPIO, Sensor Controller, High drive
capability
5F.BlockA2 | Hangcheng Industry Zone | ChenTian | Xixiang Town | Bao’an district | Shenzhen,P.R.C
Tel:+86 0755 66621530 |
www.radioland-china.com | sales@radioland-china.com
Layout Suggestion

CC2640S1
bluetooth module serial level should be 3.3 V, if the connection and 5V
level system need to increase the level conversion chip.

Bluetooth signal is highly affected by the surrounding,such as trees, metal, wall can
have certain absorption on the bluetooth signal or block, so the installation is not
recommended in the metal case.

Due to metal will weaken the function of antenna, it is suggested that Lay in the
module board,don't lay GND and a line under the antenna module, it is best to
hollow out.
NOTE:
Additional information on the Texas Instruments CC2650
device can be found in the company’s latest datasheet release at
http://www.ti.com/product/CC2650
5F.BlockA2 | Hangcheng Industry Zone | ChenTian | Xixiang Town | Bao’an district | Shenzhen,P.R.C
Tel:+86 0755 66621530 |
www.radioland-china.com | sales@radioland-china.com
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter.
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the
module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the
following: “Contains Transmitter Module FCC ID: 2AGUT-CC2640S1 Or Contains FCC ID: 2AGUT-CC2640S1”
when the module is installed inside another device, the user manual of this device must contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that
comes with the product
Any company of the host device which install this modular with limit modular approval should perform the test of
radiated emission and spurious emission according to FCC part 15C : 15.247 and 15.209 requirement, Only if the test
result comply with FCC part 15C : 15.247 and 15.209 requirement，then the host can be sold legally.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : ThinkPad
Create Date                     : 2015:10:09 11:06:45Z
Modify Date                     : 2017:09:26 11:56:54+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : ThinkPad
Title                           : RL-CC254x-S1
Creator Tool                    : WPS Office
Metadata Date                   : 2017:09:26 11:56:54+08:00
Document ID                     : uuid:64f45ccb-9f66-4117-8a23-0dd60b6921ab
Instance ID                     : uuid:da1ce388-f8a8-45a3-a76d-7efc73d91f5b
Page Count                      : 6

EXIF Metadata provided by EXIF.tools