RF Technology DBS150 VHF BASE STATION/ REPEATER TRANSCEIVER User Manual Eclipse2 manual FCC
RF Technology Pty Ltd VHF BASE STATION/ REPEATER TRANSCEIVER Eclipse2 manual FCC
USERS MANUAL
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 938478 |
| Application ID | oDkfOgd7hih0g1WIQ4qP0w== |
| Document Description | USERS MANUAL |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 7.56kB (94458 bits) |
| Date Submitted | 2008-05-08 00:00:00 |
| Date Available | 2008-05-12 00:00:00 |
| Creation Date | 2008-05-08 11:14:39 |
| Producing Software | Acrobat Distiller 7.0.5 (Windows) |
| Document Lastmod | 2008-05-08 11:14:39 |
| Document Title | Microsoft Word - Eclipse2 manual FCC.doc |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | Guang |
ECLIPSE2 SERIES RBS150 VHF BASE STATION OPERATION AND MAINTENANCE MANUAL RF TECHNOLOGY http://www.rftechnology.com.au November, 2007 Ver. 0.0.1 This manual is produced by RF Technology Pty Ltd 10 / 8 Leighton Place, Hornsby NSW 2077, Australia Copyright © 2007 RF Technology © RF Technology 2007 Conformity of USB Device Any ITE equipment attached to this device will need to be either certified or covered by a FCC declaration of conformity © RF Technology 2007 WARNING Changes or modifications not expressly approved by RF Technology could void your authority to operate this equipment. Specifications may vary from those given in this document in accordance with requirements of local authorities. RF Technology equipment is subject to continual improvement and RF Technology reserves the right to change performance and specification without further notice. PART 1: INTRODUCTION The Eclipse2 series is a new generation base station developed by RF Technology. The design is based on the software defined radio (SDR) technology which allows user to upgrade their base stations from standard FM modulation to P25 or other digital protocols without hardware changes. The Eclipse2 base station inherits RF Technology’s modular design concept which provides extensive flexibility for users, e.g. stand alone transmitter/receiver, cross-band operation, etc. Utilized with the DSP technology and the build-in Ethernet engine, all operating parameters can be monitored and controlled remotely. A typical base station system includes a transceiver DTR150 which is in one standard 4U height and 2W width; an RF power amplifier DPA150 (in standard 4U height and 4W width); and a switch mode power supply SMPS12 (in standard 4U height and 2W width). All the modules can be easily plugged into one RF Technology’s standard 19 inch 4U rack. As the DTR150 transceiver can deliver up to 5 Watt RF output power, the power amplifier may not be necessary, this allows more than one base station systems (up to 6) to be mounted into a single 19 inch rack The base station is designed for continuous operation from –30°C to +60°C (–22°F to +140°F). © RF Technology 2007 PART 2: TRANSCEIVER 2.1 OPERATING BASICS The transceiver will need approximately 30 seconds to boot up after power up. When the transceiver is ready to operate, a voice report (if enabled) can be heard from front panel speaker, and Digital/Analog LED will indicate that the transceiver current working mode. 2.1.1 Front Panel Controls and Indicators The front-panel includes LED indicators, tactile switch buttons, a microphone connector and an USB (type A) connectors, refer figure.1 for details Status Up Test Left Right Down Reset Analog Microphone Connector USB Connector Tx Digital Power Rx Alarm Figure1: Eclipse2 Transceiver Front panel 2.1.1.1 Buttons: Status Test Up – Press this button to listen the voice report – Press this button to key up the exciter (if front panel test key enabled) – Press this button to increase the speaker volume © RF Technology 2007 Down Left Right Reset – – – – Press this button to decrease the speaker volume Press this button to change channel to next lower programmed number Press this button to change channel to next higher programmed number The reset switch mounted inside base station, used for reset the transceiver without power cycle, use a small pin (e.g. paper clipper) to access this switch 2.1.1.2 Indicators: Power Digital Analog Tx Rx Alarm – This LED (on) indicates that DC power supply is applied to the transceiver – This LED (on) indicates that the transceiver is operating in Digital mode – This LED (on) indicates that the transceiver is operating in Analog mode, - if the transceiver is operating in dual mode, both Digital and Analog LED will be on – This LED (on) indicates the transceiver’s transmitting path is active – This LED (on) indicates the transceiver’s receiving path is active – This LED (flash) indicates the transceiver is in alarm state, press the status button to listen the alarm information 2.1.1.3 Connectors: Microphone – RJ45 connector for front-panel microphone input USB – USB (type A) connector for connecting host PC via a standard USB cable to monitor or program the transceiver 2.1.2 Rear Panel Connectors 2.1.2.1 System I/O: The male D shell, 25-pin connector is the main interface to the transceiver. The pins of the connection are described in table 1. Pin No. 1, 4 Description Power supply, positive 13,25 15 16 Power supply, negative System serial bus, Data out System serial bus, Clock Exciter PTT input Receiver COS output AUX audio input AUX audio output 8, 17 Audio signal ground Line input + 19 Line input - Line output + © RF Technology 2007 Specification Input: +13.8VDC (minimum 10.8V, maximum 16V) Input: Ground Output: +3.3V TTL logic Output: +3.3V TTL logic Input: Low active level ≤ +2.5V) Output: open collector, Imax = 100mA Input: unbalanced 4.7kohm, DC to 3000Hz Output: unbalanced 4.7kohm, DC to 3000Hz Input: ground Input: balanced 600ohm, 300 to 3000Hz, -20dbm to +10dbm Input: balanced 600ohm, 300 to 3000Hz, -20dbm to +10dbm Output: balanced 600ohm, 300 to 3000Hz, -20dbm to +10dbm 20 Line output - 21 GPS 1 pulse/sec input Monitor speaker output 22 10 23 11 24 12 System serial bus, Data in System serial bus, CS0 System serial bus, CS1 T/R relay output External squelch input Spare GPIO input Spare GPIO output Output: balanced 600ohm, 300 to 3000Hz, -20dbm to +10dbm Input: +3.3V to +15V TTL logic Output: unbalanced 8 ohm 300 to 3000Hz, 3 Watt maximum Input: +3.3V TTL logic Output: +3.3V TTL logic Output: +3.3V TTL logic Output: open collector, Imax = 100mA Input: Low active (Vin ≤ +2.5V) Input: Low active level ≤ +2.5V) Output: open collector, Imax = 100mA Table1: D25 System I/O Connector signals 2.1.2.2 E/M Line: This RJ45 connector provides easy connection to the equipment such as microwave links, the signal of the E/M line connector is described in table2. Pin No. Description E+ ELine out + Line out - Line in + Line in - M+ M- Specification Input: 10V to 48V Input: 10V to 48V Output: balanced 600ohm, 300 to 3000Hz, -20dbm to +10dbm Output: balanced 600ohm, 300 to 3000Hz, -20dbm to +10dbm Input: balanced 600ohm, 300 to 3000Hz, -20dbm to +10dbm Input: balanced 600ohm, 300 to 3000Hz, -20dbm to +10dbm Output: sink current 150mA Output: sink current 150mA Table2: RJ45 E/M Line Connector signals 2.1.2.3 Ethernet: The RJ45 Ethernet connector is used for networking the base station via IP protocol, a host PC can use this connector to monitor and control the base station locally or remotely. The transceiver supports 10/100Mbs specification (defined by IEEE802.3u) and MDI/MDI-X auto crossover function which means either straight though or crossover cable can be used to connect the base station. There are two LEDs embedded in the RJ45 Ethernet connector, the green LED indicates that the Ethernet link is active; the yellow LED indicates TX/RX status between the base station and the network. © RF Technology 2007 2.1.2.4 RF input: The receiver RF input connector: 50ohm female, N type. 2.1.2.5 RF output: The exciter RF output connector: 50ohm female SMA. 2.1.2.6 RS232 and external reference clock (optional) The female D shell, 9-pin connector is an optional interface to the transceiver. RS232 and external reference clock (EXT_RFE) signals share this connector. The pins of the connection are described in table 3. Pin No. Description Specification GND(RS232) TXD (RS232) RXD(RS232) GND(RS232) External reference clock 4, 6, 7 GND(EXT_REF) NC Ground Output: +/-5V to +/-15V TTL logic Input: +/-5V to +/-15V TTL logic Ground Input, sine wave or TTL logic, Minimum input: 0.5Vp-p Ground No connection on pin 4, 6, 7 Table2: RJ45 E/M Line Connector signals 2.2 PROGRAMMING AND MONITORING Programming and monitoring is most easily accomplished with RF Technology’s Service Kit software. This software is based on Java platform and can be run under various operation systems on the host PC, it provides a number of additional useful facilities for the base station configurations. Service Kit software allows configuring of base station (e.g. the channels, output power, signal path, etc.) without hardware alignment, it also provides a simple means of calibrating the RF power, RSSI level, line levels. For more details of Service Kit software, please refer the document: RFT Doc No. 0305917801 (Service Kit Operation Manual). Service Kit software and the operation manual can be supplied by your dealer, distributor or by contacting RF Technology directly. There are three interfaces which can be used for connecting host PC and base station: © RF Technology 2007 2.2.1 Connecting with Ethernet Ethernet is the most powerful interface of the base station, especially for remote monitoring and controlling via Internet. Each base station has a unique IP address, to connect, the host PC must be in the same sub net with the base station. 2.2.2 Connecting with USB The front-panel USB connector can be also used for connecting to host PC, the operation system need a proper driver to recognize the base station. Make sure the diver is installed in host PC so that Service Kit can communicate properly with the base station via the USB interface. 2.2.3 Connecting with RS232 (optional) The RS232 share the same internal serial port with the USB interface, only one (either RS232 or USB, if both interface are connected, USB has the priority) of them can be used at the same time. Only three wires (TXD, RXD and GND) are used in this RS232 interface. The transceiver supports up to 115.2kbps data rate, make sure the host PC serial port setting is 8 data bits, 1 stop bit, none parity and no flow control. 2.3 CIRCUIT DESCRIPTION The following descriptions should be read as an aid to understanding the block and schematic diagrams given in the appendix of this manual. The transceiver consists three major subparts: Processor (Master) board, Interface (Main) board, and RF modules. 2.3.1 Processor (Master) board The Processor (Master) board is a six-layer, double side component mounted PCB assembly. The most important parts of the base station, such as CPU, DSP and digital IF receiver, are embedded in this master board, two 40-pin connectors on this board allows user inserting/removing it from the interface (main) board. The CPU (U1) is a single chip 32-bit RISC processor, it controls all the operating functions of the base station. The support chips include a 16Mbyte Flash (U9) and 64Mbyte SDRAM (U7, U8). The base station software and configuration databases are stored in the Flash memory. The system serial bus and GPIO of the RISC processor are connected to the system interface board via two 40-pin connectors. © RF Technology 2007 The 10/100Mbps Ethernet Physical Layer single chip transceiver (U10) provides the interface between RISC processor and the Ethernet. A serial ATA cable is used for connecting between the Master board and System interface board. The DSP (U2) is a 32-bit fixed-point digital signal processor, it provides the base band processing such as: modulation, demodulation, RSSI/SINAD calculation, sub-tone encoding/decoding and audio processing of the base station. The DSP software is modularized, the modulator, demodulator, pre-emphasis, de-emphasis, filters and gain are individual modules, user can connect the disconnect any module by the Service Kit software for different applications. The DSP also controls the frequencies of the PLL chips in the RF modules. The digitized audio signal interfaced to the CODEC of the system interface board is via the DSP serial port. The digital IF receiver consists an ADC (analog to digital converter, U4) and a DDC (digital down converter, U3). The pre-filtered analog IF signal from the receiver module is fed to ADC, converted to the digital IF and passed to the DDC via the parallel bus, the DDC mixes the incoming digital IF with the internal Numerically Controlled Oscillator (NCO) frequency signal to produce the 0Hz IF, the DDC also provides decimating and further filtering for the IF signal. The output from the DDC is in complex I/Q format, sent to the DSP for demodulating via the serial bus. The clock of ADC, DDC and DSP is from the system interface board. 2.3.2 Interface (Main) board The Interface (Main) board provides the interfaces among the Processor (main) board , RF modules and external equipment. The function of the Interface board can be described as following sub sections. 2.3.2.1 Audio signal processing External audio signals from/to the base station are processed in this section. The balanced audio input from RJ45 E/M Line connector or D25 system connector is passed, after line matching transformer (T1) coupling, to a Trans-conductance amplifier (U11), the gain of the amplifier is controlled by the RISC processor. The output of this amplification stage is then amplitude limited, attenuated and filtered before send to the channel 1 of the CODEC (U12). The CODEC encodes the analog audio to digital PCM signal send to the DSP via the serial bus. The Microphone input from front panel RJ45 connector is amplified by op-amplifier (U16), amplitude limited and attenuated then fed to the cannel 2 of the CODEC (U12). The CODEC encodes the analog audio to digital PCM signal send to the DSP via the serial bus. The AUX input signal from D25 system connector is DC coupled, filtered and amplitude limited by the op-amplifier (U16), then fed into a 16-bit ADC (U17) to convert to the digital signal. The digitized signal is send to the DSP via the serial bus. This AUX input is useful for low frequency (down to 0Hz DC) signals, the DC offset of input signal is © RF Technology 2007 shifted by the bias circuit which is controlled by the RISC processor to give the maximum dynamic range for the ADC. The CODEC has two identical channels, the output of channel 1 is used for line output. PCM signal from the DSP is decoded to analog audio, and amplified, buffered by opamplifier U10, coupling through the line matching transformer (T2), and sent to the RJ45 E/M Line connector and the D25 system connector. The channel 2 output of the CODEC is used for monitor speaker, PCM signal from the DSP is decoded to analog audio, amplified by a Trans-conductance amplifier (U11), this amplifier is used as the speaker volume control. The power amplifier (U13) provides additional power gain to drive the internal and external speaker. A 16-bit DAC (U14) converts the digital output from the DSP to analog signal, the signal is filtered and buffered by op-amplifier (U10), then sent to the D25 system connector. The amplifier is DC coupled, the DC offset can be set by the bias circuit which is controlled by the RISC processor. This output is useful for low frequency application such as sub-tone, and NRZ digital signals. 2.3.2.2 I/O and Controls The RISC processor uses serial buses and GPIO to control the base station. A 10-bit 11-channel ADC (U7) senses the following signals and passes the data to the RISC processor via serial bus: Channel 0: exciter PLL tuning voltage Channel 1: exciter forward power of the power amplifier Channel 2: exciter reverse power of the power amplifier Channel 3: receiver PLL tuning voltage Channel 4: Interface board temperature Channel 5: Input power supply voltage Channel 6: receiver power supply voltage Other channels are reserved for future usage. A 10-bit 8-channel DAC (U6) converts data from the RISC processor serial bus to analog voltage for following functions: Channel 0: Channel 1: Channel 2: Channel 3: Channel 4: Channel 5: Channel 6: Channel 7: Channel 8: monitor speaker volume control 600 ohm audio Line input gain control exciter reverse power of the power amplifier AUX audio input bias setting AUX audio output bias setting receiver IF amplifier gain control (not used in release1 RX module) exciter RF output power control exciter VCO bias setting receiver VCO bias setting The op-amplifiers (U4, U28) are used for converting DAC output to proper voltage which is required by the system hardware. © RF Technology 2007 The Interface board accepts both TTL PTT input and E/M signaling, the TTL PTT is buffered by Q4,Q5, E/M signal is isolated by Opto-coupler U3 to system I/O level. The output of the RISC I/O logic is buffered by U1,Q1-Q3 for interfacing the external logic. The solid-state relay Opto-coupler is used to isolate the system I/O from E/M signal. A dual retriggerable monostable multivibrator (U5) in the circuit is functioned as a IRQ generator, it senses the changes of the Input logic and sends a narrow pulse to the RISC processor for trigging the processing IRQ. U31 is a USB to RS232 bridge which transfers the USB data between the front panel connector and the system serial bus. U9 is an transceiver which converts RS232 +/-15 logic from the rear panel to serial bus level. U30 is a bus switch to select one of above passing through to the RSIC processor. Header (H4) is used only for emergency system booting purpose, do not assert jumper into this header. 2.3.2.3 Clock generator the 12.8MHz TCXO (X1) output is buffered (by U26) and divided by 4 (U29) to provides PLL reference frequency for exciter and receiver. The frequency doubler double 12.8MHz frequency to 25.6MHz to provide system clock for digital IF receiver. 2.3.2.4 Voltage regulators There are nine voltage sources generated by the voltage regulator VTX VRX D3V3 A3V +12V +5V +1V8 -20V -12V – – – – – – – – – +12.5V DC for TX module +12.0V DC for RX module +3.3V DC for Processor (Master) board and 3V TTL logic +3.15V DC for analog 3V rail +12.0VDC for analog circuits +5V DC for TCXO and 5V TTL logic +1.8V DC for Flash core supply on the Processor (Master) board -20.0V DC for TX and RX VCO bias setting -12.0VDC for analog circuits The input power supply voltage is 13.8VDC, LDO (U19, U22) provides 12.5V (Imax = 1.5A) and 12V DC (Imax = 800mA) for TX and RX module. Switch mode DC-DC converter (U20) generates digital 3.3V DC rail (Imax=2A) for the Processor board and Interface board, then regulated to 3.15V analog DC rail by LDO (U21) for 3V analog circuits in the transceiver. The DC-DC converter (U23) provides –20V negative supply voltage for VCO bias amplifier (U4). Voltage regulator (U24) generates –12V DC supply analog circuits of the interface board. 2.3.3 RF modules © RF Technology 2007 2.3.3.1 TX module The TX module can be divided into the VCO, PLL, PA and the Data storage section. The Voltage Controlled Oscillator (VCO) The Voltage Controlled Oscillator uses a junction FET (Q2) which oscillates at the required transmitter output frequency. Varactor diodes (D2, D9, D10, and D11) are used by the PLL and bias control circuits to keep the oscillator on the desired frequency. Transistor Q1 is used as an active filter to reduce the noise on the oscillator supply voltage. The VCO is keyed ON by the RISC processor through Q3, It is keyed ON when any of the PTT inputs are active or self-calibrations, but OFF at all other times. The VCO output is amplified by monolythic amplifier U4 before being fed to the PLL chip (U10). The Phase Locked Loop (PLL) The frequency reference for the PLL is from the Interface board via a 20pin connector. A fractional-N PLL synthesiser (U10) is used in the TX module, this fractional-N synthesiser provides very fine frequency resolution which enables the PLL used as a FM modulator by modulating the PLL data. The modulation data is provided by DSP via the serial bus. The phase detector output (charge pump) signal of U10 is smoothed and filtered by the loop filter to form the tuning voltage for the VCO circuit. The Power Amplifier (PA) Amplifiers (U1, U2) increase the VCO output to a sufficient level to drive the power amplifier (U3). The output power level of the PA is controlled by RISC processor via bias pin of U3. The directional coupler (D3, D4) detects the forward and reverse power components, the detected voltages are then amplified by U7 and U8 to provide proportional dc levels to the RISC processor. The output from U3 is further filtered by the low pass filter to reduce higher order harmonics. U1, U2 and U3 are not switched on until the PLL has locked and had time to settle. This prevents any momentary off channel transmission when the transmitter is keyed. The Data Storage Each TX module has an EEPROM for storing the individual module information such as, TX module serial number, model name, frequency range, calibration data etc. This is allows user to simply replace the TX module in the transceiver without redo the alignment and calibration. The data is transferred between EEPROM and RISC processor via the serial bus. 2.3.3.2 RX module The RX module can be divided into the Font-end Amplifier, LO, PLL, IF amplifier and the Data storage section. The Front-end Amplifier © RF Technology 2007 A two-pole voltage tuned filter (D6, D7, L18-20, L23 and L24) is used to limit the RF bandwidth prior to the RF amplifier transistor Q1. The tuning voltage is supplied by the RISC processor through the bias control. The circuit values are chosen so that the centre frequency tracks the VCO bias voltage. RF amplifier transistor Q5 is followed by a second two-pole voltage tuned filter (D4, D5, L7, L11, L14, L21 and L22) which provides additional image and spurious frequency rejection. The filter output is connected to the RF input port of the mixer MX1 via a 1.8dB pad. The Mixer MX1 is a level 13 double balanced diode ring mixer with excellent Intermodulation performance. It has a conversion loss of approximately 6 dB. The gain between the receiver input and the mixer input is approximately 10 dB so that the total gain between the antenna input and the IF input 3-4dB. The network (C28, C74, L29, L15, L16 and R20) passes the IF frequency of 45 MHz and terminates the RF and LO components. The Local Oscillator (LO) The LO is a Voltage Controlled Oscillator (Q2) which oscillates at the required transmitter output frequency. Varactor diodes (D2, D9 - D11) are used by the PLL and bias control circuits to keep the oscillator on the desired frequency. Transistor Q1 is used as an active filter to reduce the noise on the oscillator supply voltage. Monolithic amplifiers U1, U2 and transistor Q6 amplify the VCO output to approximately +16dBm then feed to the mixer via a 3dB pad. The Phase Locked Loop (PLL) The frequency reference for the PLL is from the Interface board via a 20pin connector. A fractional-N PLL synthesiser (U10) is used in the RX module, PLL frequency PLL is set by DSP via the serial bus. The phase detector output (charge pump) signal of U10 is smoothed and filtered by the loop filter to form the tuning voltage for the VCO circuit. The IF Amplifier The first IF amplifier uses two parallel connected JFET transistors Q3 and Q4 to obtain 8-10 dB gain. The two transistors provide improved dynamic range and input matching over a single transistor. A 4-pole 45 MHz crystal filter (FIL1, FIL2) is used between the first and second IF amplifiers. The second IF amplifier (U3, U5) provides additional 35dB gain to drive the digital IF. A two pole crystal filter (FIL3) is used as an anti-alias filter of the digital IF. The Data Storage Each RX module has an EEPROM for storing the individual module information such as, TX module serial number, model name, frequency range, calibration data etc. This is allows user to simply replace the RX module in the transceiver without redo the alignment and calibration. The data is transferred between EEPROM and RISC processor via the serial bus. © RF Technology 2007 2.4 FIELD ALIGNMENTS As the TX and RX module is pre-tuned for the whole operational frequency range and level adjustment of signal path is done by software (local or remotely), there is no field alignment required for optimizing the performance. 2.5 SPECIFICATIONS 2.5.1 Description The transceiver is a digitized, software upgradable radio, The exciter and the receiver can be configured as base station, repeater or the stand-alone unit. The exciter normally has maximum 5 Watt output which is used to drive a high power amplifier. It can also be used alone in lower power applications. The output power can be preset between 0.3 and 5 watts. All necessary control and 600 ohm line interface circuitry is included. 2.5.1.1 Channel Capacity Although most applications are single channel, it can be programmed for up to 256 channels (from CH0 to CH255). Each channel can have it’s own name, TX/RX frequencies and profiles. 2.5.1.2 Sub Audio Signaling Full EIA CTCSS capability as well as nonstandard sub tones are built into the modules. The CTCSS tone can be programmed for each channel in their profiles. This means each channel can represent a unique TX/RX and tone frequency combination. 2.5.1.3 Channel Programming The channel information is stored in Flash memory and can be programmed via the Ethernet, USB or RS232 interface using a Host PC and RF Technology’s Service Kit software. 2.5.1.4 Channel Selection Channel can be select by Service Kit or front panel buttons (if enabled). 2.5.2 Physical Configuration The transceiver is designed to fit in a 19-inch rack mounted frame. The installed height is 4 RU (178 mm) and the depth 350 mm. The transceiver is 63.5 mm or 2W (two Eclipse Modules) wide. The weight of the transceiver is approximately 1.6kg © RF Technology 2007 2.5.3 Electronic Specifications: 2.5.3.1 Overall Frequency Range: Channel spacing: External reference: Monitor speaker output: Microphone input: Duty cycle: Power Supply: Current Drain: Operating temperature: 150MHz to 174MHz 12.5kHz / 25kHz 5MHz / 10MHz/ 12.8MHz 3 watts @ 8 ohm 6 mV RMS @200 ohm 100% +13.8VDC +/-10% (Negative Ground) 2A Max with 5 Watt TX output power 750mA Max with TX OFF -30°C to +60°C 2.5.3.2 Receiver Frequency Spread: Frequency Stability: Frequency Step: First IF frequency: Second IF frequency: Sensitivity: Selectivity: Spurious Rejection: Intermodulation: Modulation acceptance: Noise squelch: Carrier squelch: Audio Response: Audio Distortion: Line output level: 24MHz +/-1ppm (-30°C to +60°C) 1Hz 45 MHz 0 Hz 12dB SINAD @ -119dBm (0.25uV) RF Input 80dB for 25kHz Channel spacing 75dB for 12.5kHz Channel spacing 90dB 85dB 7.5kHz for 25kHz Channel spacing 3.75 kHz for 12.5kHz Channel spacing Adjustable from 0 to 26 dB SINAD Adjustable from –120dbm to –60dBm 300Hz to 3000Hz +1/-3dB, Flat or 6dB per Octave de-emphasis < 3% -20dbm to +10dbm @600ohm 2.5.3.3 Exciter Frequency Spread: Frequency Stability: Frequency Step: Maximum deviation: Output power: Spurious & harmonics: Hum & Noise: Audio Response: Audio Distortion: Line input level: © RF Technology 2007 24MHz +/-1ppm (-30°C to +60°C) 1Hz 5kHz for 25kHz Channel spacing 2.5kHz for 12.5kHz Channel spacing 0.3 Watt to 5 Watt programmable -36dbm -55dB for 25kHz Channel spacing -49dB for 12.5 kHz Channel spacing 300Hz to 3000Hz +1/-3dB, Flat or 6dB per Octave de-emphasis < 3% -20dbm to +10dbm @600ohm 2.5.4 Connectors 2.5.4.1 Antenna Connector Receiver: Exciter: Type N 50ohm Female Mounted on the module rear panel SMA 50ohm Female Mounted on the module rear panel 2.5.4.2 Power & I/O Connector 25-pin “D” Male Mounted on the rear panel 2.5.4.3 Ethernet Connector LED Embedded RJ45 Mounted on the rear panel 2.5.4.4 E/M Line Connector RJ45 Mounted on the rear panel 2.5.4.5 RS232 & External Reference Connector 9-pin “D” Female mounted on the front panel 2.5.4.6 Microphone connector RJ45 Mounted on the front panel 2.5.4.7 USB Type A female Mounted on the front panel © RF Technology 2007 2.6 PART LIST The part reference of 2.6.1 Processor (Master) board 2.6.2 Interface Main Board 2.6.3 TX module 2.6.4 RX module PART 3: POWER AMPLIFIER Operation basics © RF Technology 2007
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2008:05:08 11:14:39+10:00 Create Date : 2008:05:08 11:14:39+10:00 Format : application/pdf Title : Microsoft Word - Eclipse2 manual FCC.doc Creator : Guang Document ID : uuid:7bb9291e-3f94-4b9d-a923-21d1fe07f876 Instance ID : uuid:d5c9ff3f-7383-446e-be09-dac5c9c69cda Page Count : 17 Author : GuangEXIF Metadata provided by EXIF.tools