RSI VIDEOTECHNOLOGIES CT01 Indoor Contact Transmitter User Manual Manual IRT601

Download:
Mirror Download [FCC.gov]
Document ID	3346795
Application ID	KC0r4F0eZo9V9wEG0C3bQA==
Document Description	Manual_IRT601
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	35.6kB (445039 bits)
Date Submitted	2017-04-06 00:00:00
Date Available	2017-04-06 00:00:00
Creation Date	2017-01-17 11:46:43
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2017-01-17 11:46:45
Document Title	Manual_IRT601
Document Creator	Adobe InDesign CC 2017 (Windows)

INSTALLATION SHEET
INDOOR RELAY TRANSMITTER IRT200 IRT601 IRT702
DOC. - REF. 219-IRT
MODIF. DATE : NOVEMBER 2016
VERSION : 08.XX.XX
Product presentation
Installation guidelines
The IRT indoor relay transmitter is designed
for use with Videofied™ wireless security
systems.
The contact includes the following features :
• Completely wireless and powered by a
Lithium battery
• Dual tamper function provides detection
for both wall and cover tamper
• Transmits check-in/status signal every 8
minutes
• Programmable radio output for wired
devices trigger
For easier installation, programming and RF testing should be
done to check proper communication between the control
panel and all system devices before mounting system devices.
Install the detector and other system devices in the following
order:
> Programming/RF Testing - program the relay and all other
devices into the control panel and test RF communication from
each intended device location to the control panel.
> Mounting - Mount the relay at the tested location.
Programming/RF Testing/Mounting
The following provides summarized steps for device
programming, testing and mounting. For complete details,
refer to the control panel installation manual.
1 Loosen the screw, open the box and
insert the batteries.
Screw
9 Press YES/OK to end the radio range test then press ESC
NO.
10 The display shows NAME + LOCATION:
Close the box and tighten the screw.
Enter appropriate device name/location (up to 16 characters),
then press YES/OK. The display shows the device number and
name for confirmation.
3 Access to the panel configuration
menu.
4 Proceed through menus until the
display shows ADD A NEW DEVICE.
11
The display shows ENTERING A NEW DEVICE?
Repeat steps 1 - 14 for remaining devices.
5 Press YES/OK. The display shows
PRESS PROGRAM BUTTON OF DEVICE.
6 Using a paperclip, press and release
the relay INIT button.
The contact LED flashes. Wait for the
keypad to display TRANSMITTER (1-24)
RECORDED.
INIT button
7 Press YES/OK. The display shows
RADIO RANGE TEST?
Press YES/OK again. The IRT LED starts
flashing and keypad display shows TEST
IN PROGRESS.
8 Take the transmitter to its intended
mounting location and make sure that
the LED flashes continuously, indicating
good communication with the control
panel.
LED
INSTALLATION SHEET
INDOOR RELAY TRANSMITTER IRT200 IRT601 IRT702
Remove the base from the contact.
2 Hold the base against the wall and mark the mounting
points.
Drill.
Mount the base on the wall.
Mounting
brackets
5 Connect 2 AWG22 wires from the devices to trigger (sirens,
flashes, cameras, smoke generators, garage doors, etc.) to the
input terminals.
Connect to the
wired devices to
trigger
Mount the IRT on its base and lock with the screw.
INSTALLATION SHEET
INDOOR RELAY TRANSMITTER IRT200 IRT601 IRT702
Security notes / (FR) Notes de sécurité / (DE) Hinweise zur Sicherheit
English
Français
Deutsch
• Remove the batteries before any
maintenance !
• WARNING, there is a risk of explosion if a battery
is replaced by an improper model !
• Observe polarity when setting up the batteries!
• Do not litter the batteries when they are used!
Dispose of them properly according to Lithium
Metal requirements
• Retirez les piles avant toute opération de
maintenance !
• Attention ! Il y a un risque d'explosion si la batterie
utilisée est remplacée par un mauvais modèle !
• Respectez la polarité lors de la mise en place des
piles !
• Ne jetez pas les batteries usagées !
Ramenez-les à votre installateur ou à un point de
collecte spécialisé.
• Batterien vor jeglichen Wartungsarbeiten
entfernen!
• Vorsicht, es besteht Explosionsgefahr, wenn eine
Batterie durch eine Batterie falschen Models
ersetzt wird!
• Achten Sie beim Einsetzen der Batterien auf die
Polung!
• Entsorgen Sie Batterien nicht im normalen
Haushaltsmüll! Bringen Sie Ihre verbrauchten
Batterien zu den öffentlichen Sammelstellen.
FCC Regulatory Information for USA and CANADA
FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the FCC authorization
to operate this equipment.
FCC Part 15.105 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance of 20 cm between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s)
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
L’appareil ne doit pas produire de brouillage, et
2 L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
INSTALLATION SHEET
INDOOR RELAY TRANSMITTER IRT200 IRT601 IRT702
ELECTRICAL PROPERTIES
Panel compatibility
BOX
W panels
Type C - CR123A - Lithium battery
Battery
Nominal voltage
3V
Low battery limit
2.8 V
Estimated battery life
Up to 3 years
Current consumption
45 µA
Max
35 mA
Open-collector
32 g (without battery)
Weight
Environmental properties
Max relative humidity
-10°/+55°C
75%, without condensing
Installation / Mounting
Wall mounting
2 screws
1 screw
STANDARDS AND CERTIFICATIONS
RF S2View® technology
Spread spectrum RF bidirectional
868MHz (IRT 200)
Operating frequency
• 868MHz - IRT200 (Europe, Africa, Asia)
• 915MHz - IRT601 (Americas)
• 920MHz - IRT702 (Australia, Chile, Peru, Paraguay)
Compliant with the annex IV of the R&TTE Directive 1999/5/EC
AES algorithm encryption
Transmission security
79.3 mm x 35 mm x 24.6 mm
Dimensions
Box sealing
RADIO PROPERTIES
Radio type
ABS UL94-V0
Material
Operating temperature
Standby (1h average)
Trigger properties
Physical properties
915MHz (IRT 601)
Radio, batteries, tamper
Supervision
Integrated
Radio antenna
Part 15C
USA FCC
RSS-247 Issue 1
Canada IC
Tamper
Tamper detection
920MHz (IRT 702)
Cover and wall tamper
AS/NZS4268
Australia RCM
This symbol on the product or on its packaging indicates that this product should not be treated as household waste.
It must be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health. The recycling of materials will help to conserve natural resources.
For more information about recycling of this product, please contact your local municipality, your waste disposal
service or the company that installed the product.
EMEA SALES
23, avenue du Général Leclerc
92340 BOURG-LA-REINE
FRANCE
E-Mail : emeasales@rsivideotech.com
www.videofied.com
North American Headquarters
1375 Willow Lake Blvd, Suite 103
Vadnais Heights, MN 55110
USA
E-Mail : usasales@rsivideotech.com
The EC declaration of conformity of
this product is available by flashing
that QR code :

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Language                        : fr-FR
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c137 79.159768, 2016/08/11-13:24:42
Create Date                     : 2017:01:17 11:46:43+01:00
Metadata Date                   : 2017:01:17 11:46:45+01:00
Modify Date                     : 2017:01:17 11:46:45+01:00
Creator Tool                    : Adobe InDesign CC 2017 (Windows)
Instance ID                     : uuid:1d378ded-b7e5-448a-a5a7-d6a69af86d6e
Original Document ID            : xmp.did:9FCEE297D587E2118041A147EF51C18F
Document ID                     : xmp.id:9b70ae21-1d8b-dc4c-814b-7ea51305b414
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:f973f9cd-dc3a-3545-a11e-026803725fa5
Derived From Document ID        : xmp.did:c61a26ac-efc3-9840-a7a2-385618801356
Derived From Original Document ID: xmp.did:9FCEE297D587E2118041A147EF51C18F
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Windows)
History Changed                 : /
History When                    : 2017:01:17 11:46:43+01:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 4
Creator                         : Adobe InDesign CC 2017 (Windows)

EXIF Metadata provided by EXIF.tools