RSI VIDEOTECHNOLOGIES KF00 Keyfob User Manual Manual kf641

Download:
Mirror Download [FCC.gov]
Document ID	3289852
Application ID	oq8Y0a/+/ib27Am5q2SyhA==
Document Description	Manual_kf641
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	54.95kB (686871 bits)
Date Submitted	2017-02-21 00:00:00
Date Available	2017-02-21 00:00:00
Creation Date	2016-11-21 12:39:44
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2017-02-14 17:43:31
Document Title	Manual_kf641
Document Creator	Adobe InDesign CC 2017 (Windows)

KF 240/641/742 4-BUTTONS REMOTE KEYFOB
INSTALLATION SHEET
DOC. - REF. 217-KF
EDITION DATE : FEBRUARY 2016
Press and hold ___ & __
simultaneously for 5 seconds
Programming
Enable the device recording mode on the panel, the keypad
will display “PRESS PROGRAM BUTTON OF DEVICE”.
Press and hold the keyfob
keys simultaneously.
When releasing, the keyfob emits a beep and a flash every
second then the keyfob is recorded by the panel.
If the keyfob is not recorded, confirm that the keypad is
displaying:
PRESS PROGRAM
BUTTON OF DEVICE
then press and hold the keyfob
strongly pressing the buttons).
Commands
Full
Arming
keys again (by
Operation
Visual arming status
after holding for 2
seconds
Partial
arming 1
Press briefly and release the corresponding button to arm
(full arming or partial arming) or disarm.
Disarming
Partial
arming 2
The first beep confirms the button has been pressed. Two beeps
confirm that the panel has received the command. If the panel has
not received the command, only one beep is emitted by the keyfob.
A red double flash confirm the system full or partial arming. A green
double flash confirms disarming.
To trigger an alert, press and hold one of the partial arming keys for
2 seconds.
> Note : This keyfob is powered by a CR3032 lithium battery with a
5-year battery life.
Siren alert after
holding for 2 seconds
Silent alert after
holding for 2 seconds
Visual arming status
The keyfob emits delay beeps when the system is armed. You can
determine if a door contact is still open.
If a device is detecting while the panel is arming, the keyfob emits a
4-second long beep.
You do not need to wait for the beeps to stop to leave the premises. The
beeps will automatically stop after the configured exit delay.
System
disarmed
System
armed
INSTALLATION SHEET
KF 240/641/742 4-BUTTONS REMOTE KEYFOB
Security notes / (FR) Notes de sécurité / (DE) Hinweise zur Sicherheit
English
•
•
•
•
Remove the battery before any
maintenance !
WARNING, there is a risk of explosion if a
battery is replaced by an improper model !
Observe polarity when setting up the
battery!
Do not throw the battery when it is used!
Dispose of it properly according to Lithium
Metal requirements
Français
•
•
•
•
Retirez la batterie avant toute opération
de maintenance !
Attention ! Il y a un risque d'explosion si
la batterie utilisée est remplacée par un
mauvais modèle !
Respectez la polarité lors de la mise en
place de la batterie !
Ne jetez pas la batterie usagée !
Ramenez-la à votre installateur ou à un
point de collecte spécialisé.
Deutsch
•
•
•
•
Batterien vor jeglichen Wartungsarbeiten
entfernen!
Vorsicht, es besteht Explosionsgefahr,
wenn eine Batterie durch eine Batterie
falschen Models ersetzt wird!
Achten Sie beim Einsetzen der Batterie auf
die Polung!
Entsorgen Sie Batterie nicht im normalen
Haushaltsmüll!
Bringen
Sie
Ihre
verbrauchten Batterie zu den öffentlichen
Sammelstellen.
FCC Regulatory Information for USA and CANADA
FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the FCC
authorization to operate this equipment.
FCC Part 15.105 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s)
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
L’appareil ne doit pas produire de brouillage, et
2 L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement..
INSTALLATION SHEET
KF 240/641/742 4-BUTTONS REMOTE KEYFOB
ELECTRICAL PROPERTIES
PHYSICAL PROPERTIES
All panels
Panel compatibility
Type C
Power requirements
1x Lithium, CR3032
Battery type
3V
Nominal Voltage
5 years
Battery life
Plastic : ABS
Material
Dimensions
70 mm x 40 mm x 10 mm
40 g
Weight
Operating temperature
Max relative humidity
0°/+40°C (32°/104°F)
70%, without condensing
S2View®
RF technology
Spread Spectrum Bidirectional
Radio Type
Operating frequency
868MHz - KF240 (Europe, Africa, Asia)
915MHz - FHSS - KF641 (USA, Canada, South Amercia)
920MHz - FHSS - KF742 (Australia, South America)
AES encryption algorithm
Transmission security
Integrated
Antenna
22
Maximum keyfobs registered
Certifications
868MHz (KF 240)
In accordance with Annex IV of the R&TTE Directive 1999/5/EC
NF EN50131-3
2009 Grade 2 - Type B
NF EN50130-4
2011
NF EN50130-5
2011 Class II
915MHz (KF 641)
USA FCC (Part 15C)
Canada IC (RSS-210 Issue 8)
920MHz (KF 742)
Australia C-Tick
(AS/NZS4268, AS/NZS 60950)
This symbol on the product or on its packaging indicates that this product should not be treated as household
waste. It must be handed over to the applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health. The recycling of materials will help to conserve natural
resources. For more information about recycling of this product, please contact your local municipality, your
waste disposal service or the company that installed the product.
The EC declaration of conformity of this product is available by flashing this QR code.
www.videofied.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Language                        : fr-FR
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Instance ID                     : uuid:7f88ca73-c7e1-4dd5-8d27-660a4400809f
Original Document ID            : adobe:docid:indd:d34b060e-a676-11dc-a793-af0db84f2b18
Document ID                     : xmp.id:2f63acb1-f4b9-dd46-b9cd-d3df430c6d3b
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:c8933f58-49f4-ad40-9e9c-a385f047265f
Derived From Document ID        : adobe:docid:indd:d34b060e-a676-11dc-a793-af0db84f2b18
Derived From Original Document ID: adobe:docid:indd:d34b060e-a676-11dc-a793-af0db84f2b18
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Windows)
History Changed                 : /
History When                    : 2016:11:21 12:39:44+01:00
Create Date                     : 2016:11:21 12:39:44+01:00
Modify Date                     : 2017:02:14 17:43:31+01:00
Metadata Date                   : 2017:02:14 17:43:31+01:00
Creator Tool                    : Adobe InDesign CC 2017 (Windows)
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 3
Creator                         : Adobe InDesign CC 2017 (Windows)

EXIF Metadata provided by EXIF.tools