RSI VIDEOTECHNOLOGIES SE01 Indoor Siren User Manual

RSI VIDEOTECHNOLOGIES Indoor Siren

User Manual

www.videofied.comInstallation GuidelinesFor easier installation, programming and RF testing should be done to check for good communication between the control panel and all system devices before mounting system devices. Install the siren and other system devices in the order of the following steps:> Programming/RF Testing - program siren and all other devices into the control panel and test RF communication from each intended device location to the control panel.> Mounting - mount siren at the tested location.Programming/RF TestingThe following provides summarized steps for device programming and testing. For complete details, refer to the control panel installation manual.1 Remove bottom screws, separate cover from siren and install batteries.2 Put control panel into programming/ configuration mode.3 Using a programmed alphanumeric keypad, proceed through menus until the display shows ADD A NEW DEVICE.4 Press Yes. The display shows PRESS PROGRAM BUTTON OF DEVICE. 5 Press and release program button on siren using a paper clip end. The siren LED flashes. Wait for keypad display to show SIREN (1 - 25) RECORDED.6 Press Yes. The display shows RADIO RANGE TEST? Press Yes again. The siren LED starts flashing and keypad display shows TEST IN PROGRESS. 7 Take siren to its intended mounting location and make sure LED flashes continuously, indicating good communication with control panel.8 Press Yes to end radio range test, then press Esc/No.9 The display shows RECORDING A NEW DEVICE? Repeat steps 4 - 8 for remaining sirens.10 When finished, exit from configuration mode.Product SummaryThe Interior Siren SE 200w/601w/702w is a wireless siren designed for use with Videofied security systems. The siren includes the following features:> Totally wireless, battery operated.> Dual tamper function provides detection for both wall and cover tamper.> Transmits check-in/status signal every 8 minutes.ScrewsProgram ButtonIndoor Siren SE 200w/601w/702wPRODUCT INSTALLATION SHEET2205 - SEIS March 2015
Mounting> Use proper tools and hardware.> Mount where siren can be heard by occupants.> Mount out-of-reach of intruders to help prevent disabling of unit.1 Remove batteries.2 Hold unit up against mounting surface and mark the three mounting holes.3 Drill pilot holes and install anchors where needed.4 Place unit on mounting surface so mounting holes line up with pilot holes/anchors and secure unit with appropriate screws.5 Install batteries, observing correct polarity.6 Attach front cover.Electrical DataPanel Compatibility XL, XLL, XVIP, Visio, XT, XTIPPower requirements Four 1.5 V Alkaline Batteries Nominal Voltage 6V Low Battery Limit 4.2V Battery type Energizer Alkaline LR20, D size Battery life Up to 4 yearsRF technology S2View®Radio type Spread Spectrum BidirectionalOperating frequency 868MHz - SE200w (Europe, South Africa, Asia) 915MHz - FHSS - SE601w (USA, Canada, South America) 920MHz - FHSS - SE702w (Australia, South America)Transmission security AES encryption algorithmSupervision Polled signal every 8 minutesAntenna IntegratedTamper detection Wall and cover tamperedSpeaker impedance 4 ohmsOutput level 110 dB @ 1 meterOutput duration Configured in Control PanelBuilt-in sounder Emits entry/exit delay beeps, alarmsOperating temperature -10°/+40°C (14°/104°F)Maximum relative humidity 70%, non-condensingPhysical DataMaterial ABS—ULV0Dimensions (LxWxD) 228 mm x 168 mm x 60 mm 9 in. x 6.61 in. x 2.36 in. Weight 740 g/26 oz.(without batteries)Installation/MountingSiren/Base Two screws secure siren to base; three screws secure siren base to mounting surface. Mounting HolesINSTALLATION DATA SHEETIndoor Siren SE 200w/601w/702wStandards & Certifications 868MHz (SE200w)915MHz (SE601w)USA FCC (Part 15C) Canada IC (RSS-210 Issue 8)920MHz (SE702w)Australie C-Tick (AS-NZS4268)Compliant with the annex IV of the R&TTE Directive 1999/5/EC Ce symbole, apposé sur le produit ou sur son emballage, indique que ce produit ne doit pas être traité avecles déchets ménagers. Il doit être remis à un point de collecte approprié pour le recyclage des équipementsélectriques et électroniques. En s’assurant que ce produit est bien mis au rebut de manière appropriée, vousaiderez à prévenir les conséquences négatives potentielles pour l’environnement et la santé humaine. Le recyclage des matériaux aidera à préserver les ressources naturelles.Pour toute information supplémentaire au sujet du recyclage de ce produit, vous pouvez contacter votre municipalité, votre déchetterie ou la société qui a installé le produit.
www.videofied.comNotes de sécurité / (EN) Security notes / (DE) Hinweise zur SicherheitFrançais•Retirez la pile avant toute opération demaintenance !•Attention ! Il y a un risque d'explosion sila pile utilisée est remplacée par une pile de type incorrect !•Respectez la polarité lors de la mise enplace de la pile !•Ne jetez pas la pile usagée !Ramenez-la à votre installateur ou à unpoint de collecte spécialisé.English•Remove battery before anymaintenance !•WARNING, there is a risk of explosion if abattery is replaced by an incorrect type!•Observe polarity when setting up thebattery!•Do not throw away used battery!Dispose of it properly according toLithium Metal requirementsDeutsch•Batterie vor jeglichen Wartungsarbeitenentfernen!•Vorsicht, es besteht Explosionsgefahr, wenn eine Batterie durch eine Batteriefalschen Typs ersetzt wird!•Achten Sie beim Einsetzen der Batterieauf die Polung!•Entsorgen Sie Batterie nicht imnormalen Haushaltsmüll! Bringen SieIhre verbrauchten Batterie zu den öffentlichen Sammelstellen.FCC Regulatory Information for USA and CANADAFCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the FCC authorization to operate this equipment.FCC Part 15.105 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:> Reorient or relocate the receiving antenna.> Increase the separation between the equipment and receiver.> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.> Consult the dealer or an experienced radio/TV technician for help.Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.Operation is subject to the following two conditions:1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1 L’appareil ne doit pas produire de brouillage,et 2 L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. PRODUCT INSTALL SHEETIndoor Siren SE 200/601/702

Navigation menu