RSI VIDEOTECHNOLOGIES SE01 Indoor Siren User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2618324
Application ID	pfbJ3i4KwU1bhc/YHSNz4A==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.28kB (403457 bits)
Date Submitted	2015-05-19 00:00:00
Date Available	2015-05-19 00:00:00
Creation Date	2014-01-30 18:10:31
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2015-03-20 15:55:24
Document Title	User Manual
Document Creator	Adobe InDesign CC (Windows)

Indoor Siren SE 200w/601w/702w
P R O D U C T
I N S T A L L A T I O N
S H E E T
2205 - SEIS March 2015
Product Summary
Installation Guidelines
The Interior Siren SE 200w/601w/702w is a wireless
siren designed for use with Videofied security systems.
The siren includes the following features:
> Totally wireless, battery operated.
> Dual tamper function provides detection for both wall
and cover tamper.
For easier installation, programming and RF testing
should be done to check for good communication between the
control panel and all system devices before mounting system
devices. Install the siren and other system devices in the order of
the following steps:
Programming/RF Testing - program siren and
all other devices into the control panel and test
RF communication from each intended device
location to the control panel.
Mounting - mount siren at the tested location.
> Transmits check-in/status signal every 8 minutes.
Programming/RF Testing
The following provides summarized steps for device
programming and testing. For complete details, refer
to the control panel installation manual.
Remove bottom screws,
separate cover from siren
and install batteries.
Press Yes. The display shows RADIO RANGE TEST?
Press Yes again. The siren LED starts flashing and
keypad display shows TEST IN PROGRESS.
Put control panel
into programming/
configuration mode.
Take siren to its intended mounting location and
make sure LED flashes continuously, indicating good
communication with control panel.
Press Yes to end radio range test, then press Esc/No.
The display shows RECORDING A NEW DEVICE?
Repeat steps 4 - 8 for remaining sirens.
Using a programmed
alphanumeric keypad,
proceed through menus
until the display shows
ADD A NEW DEVICE.
Press Yes. The display
shows PRESS PROGRAM
BUTTON OF DEVICE.
Press and release
program button on siren
using a paper clip end.
The siren LED flashes.
Wait for keypad display
to show SIREN (1 - 25) 		
RECORDED.
Screws
10 When finished, exit from configuration mode.
Program Button
www.videofied.com
I N S T A L L A T I O N
S H E E T
Indoor Siren SE 200w/601w/702w
Mounting
Remove batteries.
> Use proper tools and hardware.
Hold unit up
against mounting 			
surface and mark
the three mounting
holes.
Drill pilot holes
and install anchors 			
where needed.
> Mount where siren can be heard by occupants.
> Mount out-of-reach of intruders to help prevent
disabling of unit.
Electrical Data
Mounting Holes
Place unit on mounting surface so mounting holes
line up with pilot holes/anchors and secure unit with
appropriate screws.
Install batteries, observing correct polarity.
Attach front cover.
Physical Data
Panel Compatibility
XL, XLL, XVIP, Visio, XT, XTIP
Material
Power requirements
Four 1.5 V Alkaline Batteries
Dimensions (LxWxD)
Nominal Voltage
6V
Low Battery Limit
4.2V
Battery type
D A T A
ABS—ULV0
228 mm x 168 mm x 60 mm
9 in. x 6.61 in. x 2.36 in.
Weight
740 g/26 oz.(without batteries)
Energizer Alkaline LR20, D size
Battery life
Up to 4 years
RF technology
S2View®
Radio type
Installation/Mounting
Siren/Base
Spread Spectrum Bidirectional
Operating frequency
868MHz - SE200w (Europe, South Africa, Asia)
915MHz - FHSS - SE601w (USA, Canada, South America)
Two screws secure siren to base; three screws
secure siren base to mounting surface.
Standards & Certifications
868MHz (SE200w)
920MHz - FHSS - SE702w (Australia, South America)
Transmission security
Supervision
Antenna
Tamper detection
Speaker impedance
Output level
AES encryption algorithm
Polled signal every 8 minutes
Integrated
Wall and cover tampered
USA FCC (Part 15C)
110 dB @ 1 meter
Canada IC (RSS-210 Issue 8)
Configured in Control Panel
Built-in sounder
Emits entry/exit delay beeps, alarms
Maximum relative humidity
915MHz (SE601w)
4 ohms
Output duration
Operating temperature
Compliant with the annex IV of the R&TTE Directive 1999/5/EC
-10°/+40°C (14°/104°F)
70%, non-condensing
920MHz (SE702w)
Australie C-Tick (AS-NZS4268)
Ce symbole, apposé sur le produit ou sur son emballage, indique que ce produit ne doit pas être traité avec
les déchets ménagers. Il doit être remis à un point de collecte approprié pour le recyclage des équipements
électriques et électroniques. En s’assurant que ce produit est bien mis au rebut de manière appropriée, vous
aiderez à prévenir les conséquences négatives potentielles pour l’environnement et la santé humaine.
Le recyclage des matériaux aidera à préserver les ressources naturelles.
Pour toute information supplémentaire au sujet du recyclage de ce produit, vous pouvez contacter votre
municipalité, votre déchetterie ou la société qui a installé le produit.
P R O D U C T
Indoor Siren SE 200/601/702
I N S T A L L
S H E E T
Notes de sécurité / (EN) Security notes / (DE) Hinweise zur Sicherheit
Français
•
•
•
•
Retirez la pile avant toute opération de
maintenance !
Attention ! Il y a un risque d'explosion si
la pile utilisée est remplacée par une pile
de type incorrect !
Respectez la polarité lors de la mise en
place de la pile !
Ne jetez pas la pile usagée !
Ramenez-la à votre installateur ou à un
point de collecte spécialisé.
English
•
•
•
•
Remove battery before any
maintenance !
WARNING, there is a risk of explosion if a
battery is replaced by an incorrect type!
Observe polarity when setting up the
battery!
Do not throw away used battery!
Dispose of it properly according to
Lithium Metal requirements
Deutsch
•
•
•
•
Batterie vor jeglichen Wartungsarbeiten
entfernen!
Vorsicht, es besteht Explosionsgefahr,
wenn eine Batterie durch eine Batterie
falschen Typs ersetzt wird!
Achten Sie beim Einsetzen der Batterie
auf die Polung!
Entsorgen Sie Batterie nicht im
normalen Haushaltsmüll! Bringen Sie
Ihre verbrauchten Batterie zu den
öffentlichen Sammelstellen.
FCC Regulatory Information for USA and CANADA
FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the FCC
authorization to operate this equipment.
FCC Part 15.105 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
> Reorient or relocate the receiving antenna.
> Increase the separation between the equipment and receiver.
> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
> Consult the dealer or an experienced radio/TV technician for help.
Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance of 20 cm between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
1 L’appareil ne doit pas produire de brouillage,et
2 L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
www.videofied.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2014:01:30 18:10:31+01:00
Creator                         : Adobe InDesign CC (Windows)
Modify Date                     : 2015:03:20 15:55:24+01:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Instance ID                     : uuid:82d1fa67-5d3b-4523-9c19-5587a35d59c8
Original Document ID            : adobe:docid:indd:e28ce908-a672-11dc-a793-af0db84f2b18
Document ID                     : xmp.id:f469b5aa-a884-b145-873c-63cf6cc027fc
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:78dff404-346e-064c-80f8-8f7f7e5ebb99
Derived From Document ID        : adobe:docid:indd:e28ce908-a672-11dc-a793-af0db84f2b18
Derived From Original Document ID: adobe:docid:indd:e28ce908-a672-11dc-a793-af0db84f2b18
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC (Windows)
History Changed                 : /
History When                    : 2014:01:30 18:10:31+01:00
Metadata Date                   : 2015:03:20 15:55:24+01:00
Creator Tool                    : Adobe InDesign CC (Windows)
Format                          : application/pdf
Producer                        : Adobe PDF Library 11.0
Trapped                         : False
Page Count                      : 3

EXIF Metadata provided by EXIF.tools