Radio Activity srl RA-160 DMR REPEATER – VHF BASE STATION User Manual use manual

Download:
Mirror Download [FCC.gov]
Document ID	1420978
Application ID	S18BX2EdTvCk0unzBCCc4Q==
Document Description	use manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	256.24kB (3203002 bits)
Date Submitted	2011-02-24 00:00:00
Date Available	2011-02-24 00:00:00
Creation Date	2011-01-25 13:04:48
Producing Software	Nitro PDF PrimoPDF
Document Lastmod	2011-01-25 13:04:48
Document Title	Microsoft Word - ENB32 - DMR repeater user manual 1v2.doc
Document Creator	PrimoPDF http://www.primopdf.com
Document Author:	mauro

DMR
DIGITAL MOBILE RADIO ASSOCIATION
DMR Repeater user manual
Version 1v2
Radio Activity S.r.l.
Sede: Via Ponte Nuovo, 8 - 20128 Milano – email: radio.activity@fastwebnet.it - www.radioactivity-tlc.com
Tel. 02.36514205 - FAX/Voicebox 1782242408 - Registrazione CCIAA Milano N° 1728248 - P.I./C.F. 04135130963
DMR repeater 24/01/2011
Versione 1.3
Index
RADIO ACTIVITY DMR REPEATER AND EXPANDIBILITY TO SIMULCAST NETWORK......................4
PARAMETERS CONFIGURATION AND REMOTE CONTROL ..........................................................5
HARDWARE COMPOSITION OF A BASE STATION .......................................................................6
3.1
PSU: POWER SUPPLY UNIT MODULE.............................................................................................. 6
3.2
DSP: DIGITAL SIGNAL PROCESSOR ................................................................................................. 7
3.3
RECEIVER ...................................................................................................................................... 8
3.4
TRANSMITTER............................................................................................................................... 9
3.5
I/O AND SERVICES MODULE ........................................................................................................ 10
TECHNICAL DATA....................................................................................................................11
4.1
REGULATIONS COMPLIANCE........................................................................................................ 11
4.2
GENERAL CHARACTERISTICS ........................................................................................................ 11
4.3 IP interfacing .............................................................................................................................. 12
4.3.1
LAN protocol ................................................................................................................................... 12
4.3.2
LAN requirements ........................................................................................................................... 12
4.3.3
Ports and connectors ...................................................................................................................... 13
4.3.4
Codec VoIP ...................................................................................................................................... 13
4.4 Radio frequency.......................................................................................................................... 14
4.4.1
Transmitter...................................................................................................................................... 14
4.4.2
Receiver........................................................................................................................................... 15
4.4.3
Frequency bands ............................................................................................................................. 17
4.4.4
Commutation band (without duplexer).......................................................................................... 17
4.4.5
Branching requirements ................................................................................................................. 17
4.4.5.1
TX to antenna duplex isolation requirements @10W TX RF power ........................................ 17
4.4.5.2
Suggested RX max input limits on unwanted signals............................................................... 18
4.5 Other specifications .................................................................................................................... 18
4.5.1
Environmental parameters ............................................................................................................. 19
4.5.2
Power supply................................................................................................................................... 19
4.5.3
Mechanical characteristics.............................................................................................................. 19
4.5.4
Audio balanced interfaces............................................................................................................... 19
EQUIPMENT INSTALLATION AND MAINTENANCE ....................................................................20
5.1
CONNECTIONS AND PINOUTS...................................................................................................... 20
5.2 EQUIPMENT START UP, RUNNING AND ALARMS: INDICATOR LAMPS ........................................... 27
5.2.1
PSU .................................................................................................................................................. 27
5.2.2
DSP .................................................................................................................................................. 27
Documento Riservato - non divulgabile senza autorizzazione
Pag. 2 / 31
DMR repeater 24/01/2011
5.2.3
5.2.4
5.2.5
Versione 1.3
RX .................................................................................................................................................... 28
TX..................................................................................................................................................... 28
I/O ................................................................................................................................................... 28
5.3 GENERAL RECOMMENDATIONS AND NOTES ................................................................................ 29
5.3.1
Improper use................................................................................................................................... 29
5.3.2
Thermal dissipation......................................................................................................................... 29
5.3.3
Power supply system ...................................................................................................................... 29
5.3.4
Antenna........................................................................................................................................... 30
5.3.5
AF interface ..................................................................................................................................... 30
5.3.6
Manual settings............................................................................................................................... 30
5.3.7
Self-calibration process................................................................................................................... 31
5.3.8
PPS signal ........................................................................................................................................ 31
Documento Riservato - non divulgabile senza autorizzazione
Pag. 3 / 31
DMR repeater 24/01/2011
Versione 1.3
RADIO ACTIVITY DMR REPEATER AND EXPANDIBILITY TO SIMULCAST NETWORK
Radio Activity DMR repeater is designed to be modular from both HW and SW point of view, to maximize its
flexibility and minimize costs, physical dimensions, consumptions.
Basic model already has all the characteristics to work as a double standard repeater with all the features of
analogical and digital service. It can be equipped with double receiver to counteract fading effects through
diversity space reception. It is set to host communication and synchronization embedded devices to make the
network expandable to a multi-frequency or iso-frequency multi-site system, with different type of links,
operating with different transportation system topology, like microwave, UHF, fiber optics, generic TCP/IP
connections.
Privileged communication interface is ethernet standard type, maximally compatible with more diffused
technology. This interface supports not only voice and data digital traffic, but also remote control
management, which for Radio Activity equipment is very powerful: it is possible to have a complete monitor
system of equipment status, it is possible to modify each parameter, to down-load each SW and configuration,
launch self-test and calibration functions, to perform specific tests through internal embedded function
generators and software analyzers of the station. For analogical voice traffic instead, a 2/4 wire and criteria
line interface is available.
Remote control service can be performed through an ethernet connection pre-existing in the site, or through
GPRS modem which can be integrated into the station, or through the radio channel and another Radio
Activity station.
Fully modular structure allows to best configure the radio equipment, by adding and/or changing the required
HW and SW functional blocks, to work as simple repeater, multi-frequency multi-site repeater, iso-frequency
multi-site repeater. The basic structure of a base station is made of:
∞ PSU module (not isolated 12Vdc from battery);
∞ DSP module;
∞ RX module;
∞ TX module.
Optional modules and accessories are:
∞ I/O module with line interface with or without GSM/GPRS and GPS unit;
∞ PSU module for isolated power supply sources at 12V, 24V or 48V dc;
∞ RX module with diversity receiver;
∞ Duplexer, circulator or both;
Documento Riservato - non divulgabile senza autorizzazione
Pag. 4 / 31
DMR repeater 24/01/2011
Versione 1.3
∞ Multi-receiver block for star-shaped network architectures with RF links;
∞ Antenna active splitter board.
If a network architecture is needed, Radio Activity base stations can be connected through both a RF or
ethernet link.
PARAMETERS CONFIGURATION AND REMOTE CONTROL
Working parameter of the station are completely programmable through a SW package and a PC connection.
The visible (and programmable) parameters set is very wide and extends from radio channel setting to tuning
voltage measure of each local oscillator. The software is called DMR_Manager for single base-stations or
DMR_NetControl for network systems.
Remote diagnostic of radio stations from PC can be performed through the Ethernet interface of the station.
This interface is absolutely standard and very diffused, so relatively simple to be remoted. Radio Activity
stations can be equipped with an embedded GPRS modem which will provide remote access to the station, if
the installation site is covered by this service. Each operation can be remotely performed, exactly the same as
in local connection, including FW down-loading, configuration Down-loading and up-loading, station check,
parameters changing.
Communication and supervision unit can spontaneously transmit diagnostic messages if defined “selfalarming” events happen. This is useful to automatically check the stations.
Here following an example of remote control forms:
Documento Riservato - non divulgabile senza autorizzazione
Pag. 5 / 31
DMR repeater 24/01/2011
Versione 1.3
For further details about remote control software, refer to proper documentation (SW user manuals).
3.1
HARDWARE COMPOSITION OF A BASE STATION
PSU: POWER SUPPLY UNIT MODULE
Space for optional
floating ground power
supply
External I/O
polarity
DC/DC 6.5Vcc
Equipment is power supplied by nominal
13,8Vdc from battery with negative
shorted to ground and with a maximum
current absorption of 5 A. In case of
other power supply sources, other PSU
models are available, DC/DC (nominal
12-24-48V, isolated) or AC/DC (nominal
220V) with battery charger.
Isolated external
I/O power supply
Input lightening
protection
Input polarity and
over-current
protection
Documento Riservato - non divulgabile senza autorizzazione
Pag. 6 / 31
DMR repeater 24/01/2011
3.2
Versione 1.3
DSP: DIGITAL SIGNAL PROCESSOR
The core of system’s “physical layer” is this unit which via software performs every function of signal
processing inside radio station. What other equipments implement by adding boards (like synchronizers,
phase and amplitude equalizers, signal decoders, modem, etc.), here are implemented by routines which can
be freely matched, down-loaded and with superior performance.
RTC
DSP and Processor cores
Ethernet LAN
VCTCXO
reference
I/O
AUDIO LAN
D/A and A/D converters
and audio filters
This board can process up to 8 analogical duplex signals ensuring 70 dB of SNR; it can manage 16 logical signals
which can be configured both as input and output.
Communication and control functions of module are entrusted to a microprocessor which manages
communications with external world and with other equipment modules. The microprocessor is based on
LINUX operative system; it can manage a LAN ethernet 10/100 interface both for copper line and for fiber
optic links, it is equipped with 4 serial ports to manage radio modules, GPS, auxiliary devices, external hosts; it
is equipped with a Real Time Clock with tampon battery; it controls an embedded PLL to synchronize the
entire station upon an internal (VCTCXO 0.5 ppm) or external temporal reference. DSP module is equipped
with a synchronous serial port according RS485 standard levels, which can be programmed up to 16Mbit/s and
can be used to interconnect together more transceiver or additional equipments.
Main performed functions are the following:
Documento Riservato - non divulgabile senza autorizzazione
Pag. 7 / 31
DMR repeater 24/01/2011
∞
∞
∞
∞
∞
∞
∞
∞
∞
∞
3.3
Versione 1.3
Frequency self-tuning device
Deviation self-calibration device
Analogical and digital demodulation
RF circuits testing
Phase modulator calibration
RF output power control
Low frequency lines management
DMR protocols management
Digital signals processing
Management, conditioning and routing of traffic and remote control signals from and towards
external world
RECEIVER
Receiver can be supplied as single or double for space diversity reception. Main and diversity channels are
completely independent and coherent (sharing the same local oscillators) and they are designed according to a
triple conversion heterodyne structure, with 45 MHz and 10.7 MHz intermediate frequencies and with
vectorial conversion to base-band.
Channel standard bandwidth is 12.5 KHz, but the receiver is prepared to accept also a settable channel
bandwith of 25 KHz (with double funnel option) for special applications.
Vectorial receiver gives to the DSP input the electromagnetic field vector, as received from antennas, without
performing any demodulation. By this way the DSP can sum with the appropriate phases the received signals
to obtain a “soft diversity” reception. This corresponds to an electronic antennas alignment in order to receive
the maximum available information along the incoming signal direction.
IF system
XTAL filter
10.7MHz
XTAL filter
45MHz
High IP3 Mixer
Input filter and low
noise amp.
Microcontroller
I° LO Frx+45MHz (VHF)
III° LO 10.7MHz
II° LO 34.3MHz
I° LO Frx-45MHz (UHF)
A further input (TX Test input), common for both receivers (main and diversity) is available, for the receiver
self-test and for modulator calibration. Through a DSP command, the receiver can switch its input onto test
signal generated inside transmission synthesizer module. That signal, amplitude calibrated by Factory, is
modulated at receiving frequency and received by DSP. A fundamental test loop is close by this way.
Documento Riservato - non divulgabile senza autorizzazione
Pag. 8 / 31
DMR repeater 24/01/2011
Versione 1.3
The switching between normal and test input is implemented through PIN diodes.
Receiver modules is managed by a microcontroller unit whose program is hosted inside internal e2prom flash
memory to lower parasitic emissions. This FW can be loaded through serial connection. The microcontroller, in
addition to managing internal function of the unit, transfers measured parameters to the control unit through
115.2 Kb/s serial line.
The board is realized with surface mounting components (SMD) to maximally reduce dimensions.
Modular unit is housed in a shielded, 4TE high box for 220mm Eurocards. On the frontal panel 2 LEDs are
placed for monitoring internal PLLs lock status.
3.4
TRANSMITTER
Transmitter module is realized with surface mounting components (SMD) and it is housed in a shielded, 8TE
box for 220mm Eurocards, with an heatsink mounted on side, with a thermal resistance of about 1.2°K/W. The
unit can be extracted from the front side of the rack.
synthesizer
microcontroller
power detecting strip lines
MOS power amplifiers
On the frontal panel two LEDs are placed to monitor the transmitter status.
Base-band functions, equalizing, limiting, low-pass filtering end eventual emphasis functions are performed by
the DSP unit, which provides also for nominal and maximum deviation calibration by looping modulator with
receiver.
Modulator is digital vectorial, then the synthesized signal by local oscillator implements the frequency shifting
of the signal which has been directly modulated in base-band by DSP unit and transferred to transmitter
through its I and Q components.
Documento Riservato - non divulgabile senza autorizzazione
Pag. 9 / 31
DMR repeater 24/01/2011
Versione 1.3
The amplifier is realized by three cascaded stages and RF output power regulation (between 1 and 25W) is
implemented by controlling the gates voltages of MOSFET amplifier stages. Power amplifier works in C class
and ensures a very high efficiency, lowering the needed power from supply system and lowering the thermal
dissipation inside the cabinet. Direct and reflected output power are measured by a directional coupler.
Power control circuit acts in a closed loop and keeps constant the total power at MOSFET drain. Inside the
module a thermal sensor is hosted and it is directly connected to the internal microcontroller which enables
the command for air forced cooling fan of the cabinet if the temperature rises over 85°C. Anyway, if reflected
power or mosfet temperature exceeds protection threshold, regulation circuit will lower output power up to
safe levels for transmitter.
The current flowing into final amplifier transistor is continuously monitored by microcontroller to verify the
correct functioning and to reveal an eventual efficiency degradation.
The module is equipped with an harmonic filter to lower spurious emissions under required levels by existing
regulations.
3.5
I/O AND SERVICES MODULE
I/O and Services module is a unit integrating different interfaces and functions, that for some applications can
be optional but for others become essential. For this reason the module can be differently equipped with its
different logical blocks, according to the particular application. The embedded block are the following:
∞ Telephone line interface: 2/4W+E&M line interface to remote analogical audio and perform automatic
routing through telephonic line
∞ Opto-isolated I/O: 2 input + 2 output contacts programmable (both N.O. or N.C.) for remote
monitoring local sensors and remote controlling local actuators
∞ Opto-isolated alarms: two alarms output (1 warning + 1 fatal)
∞ Analogical input: 2 not isolated inputs, 1 for voltage sensing (0..20V referred to ground) + 1 for current
sensing (4…20mA). These input can be connected the first in parallel and the latter in series with the
analogous ones of other similar equipments
∞ GSM/GPRS modem: embedded communication module for remote control if the site is covered by
GSM or GPRS service. It requires only an external passive antenna
∞ GPS receiver: embedded receiver for GPS service, with high precision Pulse Per Second (PPS) output
function in order to synchronize the station. Only an external active antenna is required
∞ RS232 converter: 115.2Kbit/s serial interface for remote control
I/O and services module is equipped with 8 LEDs on the frontal panel to monitor the status of opto-isolated
I/O, the status of GPRS modem and the presence of PPS.
Modular unit is housed in a shielded, 4TE high box for 220mm Eurocards.
Documento Riservato - non divulgabile senza autorizzazione
Pag. 10 / 31
DMR repeater 24/01/2011
Versione 1.3
SIM HOLDER
BF line interface
GSM/GPRS - GPS
I/O contacts
4.1
TECHNICAL DATA
REGULATIONS COMPLIANCE
Equipments are compliant with existing regulations, in particular:
1. EN 300 086-2: Technical characteristics and test conditions for radio equipment for analogue
speech.
2. EN 300 113-2: Technical characteristics and test conditions for non speech radio equipment
for the transmission of data.
3. ETSI TS 102361: Electromagnetic compatibility and Radio spectrum Matters (ERM); Digital
Mobile Radio (DMR) Systems.
The equipment is able to manage OSI stack layers 1 – 2 – 3 of DMR protocol, making active interaction
possible with mobile terminals.
4.2
GENERAL CHARACTERISTICS
Funnel
Maximum channels number
Operating mode
Operating mode selection
Frequency stability
I/O
Voice/data digital interface
Analogical audio interface
12.5 KHz (25KHz optional for special purpose)
200
Dual-standard, analogical and digital
Totally automatic
+/- 0.5 ppm
4 opto-isolated OUT (2 alarms + 2 generic)
4 IN (2 digital opto-isolated + 2 analogical referred to
ground)
LAN 10/100 copper or fiber optic
2/4W + E/M (BCA-C/U optional)
Documento Riservato - non divulgabile senza autorizzazione
Pag. 11 / 31
DMR repeater 24/01/2011
Base Bandwidth
Calibration and tests
Remote control
4.3
Versione 1.3
Audio 300-3400 Hz ±1dB
Modulation 0-5 KHz
Automatic at start-up and/or by remote control
Via ethernet / serial RS232 / GPRS
IP INTERFACING
4.3.1 LAN PROTOCOL
Protocols for voice packets
Protocols for BS “internal” network
control
UDP/IP (ipv4), unicast (from RA-TI-XXX to master) and multicast
(from master to RA-TI-XXX), with DSCP set to “EF” (Telephony
service class), according to RFC 4594
UDP/IP (ipv4), unicast and multicast, with DSCP set to “CS6”
(Network Control service class), according to RFC 4594
UDP/IP and TCP/IP (ipv4) unicast and broadcast with DSCP set to
Protocols for remote control, setup
“AF13” (High-Throughput Data service class), according to RFC
and surveillance
4594
Audio format
Analog: 64 kb/s – 8 bit x 8 KHz linear coded
DMR: AMBE II+TM (Advanced Multi-Band Excitation)
Analog: 60 ms – 480 bytes/samples
Audio frame block net payload
DMR selectable single/double timeslot: 60 ms – 27 bytes each
timeslot
4.3.2 LAN REQUIREMENTS
Documento Riservato - non divulgabile senza autorizzazione
Pag. 12 / 31
DMR repeater 24/01/2011
Jitter (deviation of averaged packet
time delay)
Maximum delay
Packet loss
Versione 1.3
The Base Station is able to compensate Jitter delay up to 200 ms.
The total delay averaged + jitter must not exceeds 400ms (each
way)
The Base Station is able to compensate round trip delay less then
900ms (jitters included)
< 0.1 %
SLAVE:
70 kb/s in analog to/from Master
Minimum
bandwidth
(network
signaling and remote control polling
inclusive)
24 kb/s in DMR to/from Master (both timeslots)
MASTER to serve N SLAVES (both timeslots):
70 kb/s in analog to Slaves, 70 kb/s x N from Slaves
24 kb/s in DMR to Slaves, 24 kb/s x N from Slaves
4.3.3 PORTS AND CONNECTORS
UTP LAN Port
Optical LAN Port (option)
Ethernet 10BT/100TX (auto MDI/MDI-X) on an RJ45 socket
Ethernet 100FX on SC-SC socket
Serial control Port
RS232 V.24 asynchronous 600 ÷ 115200 bps on a DB9 female
connector
BUS control Port
TTL on a dual-in-line 10 pins male connector
4.3.4 CODEC VOIP
Uncoded audio source
64 kbps – 8bitx8KHz
Net bit-rate (1CH)
2450 bps
FEC Coded bit-rate (1CH)
3600 bps
Audio frame block
20ms
Documento Riservato - non divulgabile senza autorizzazione
Pag. 13 / 31
DMR repeater 24/01/2011
Coder algorithm
DMR compatibility
4.4
Versione 1.3
AMBE II+TM (Advanced Multi-Band Excitation)
Motorola Mototrbo series
RADIO FREQUENCY
Radio Transceiver model RA080, RA160, RA450, RA900, typical values.
4.4.1 TRANSMITTER
Module output power
RF final transistor protection to high
temperature
Available modulation
Modulation bandwidth
1/5/10/15/20/25 W
85°C +/- 5°C progressively reducing the RF power
FM, PM, GFSK, 4FSK
0 .. 5000 Hz
Synthesis step
4/5/6,25/10 KHz
Transmitting duty cycle
Continued 100%
ROS protection
Min.10’ in short circuit as well as in open circuit
-75 dBc @25KHz
Adjacent channel noise
-65 dBc @12.5KHz
FM distortion
< 1.5 %
-56 dBp @25KHz
Noise
-50 dBp @12.5KHz
Documento Riservato - non divulgabile senza autorizzazione
Pag. 14 / 31
DMR repeater 24/01/2011
Frequency stability
Versione 1.3
0.5 p.p.m.
-20dBm to avoid intermodulation
Max reverse input signal
+20dBm no damage
4.4.2 RECEIVER
-113 dBm @20 dBp SINAD
Maximum sensitivity
-118dBm @5% BER without diversity
-121dBm @5% BER with diversity
Operating maximum input
-10 dBm
Maximum input without permanent
damages
+10 dBm
Reception mode
Received signal band
Synthesis step
Vectorial I e Q
0..5000 Hz
6,25 KHz
8 dB @25 KHz
Co-channel protection
12 dB @12.5KHz
73 dB @25 KHz
Adjacent channel selectivity
62 dB @12.5 KHz
Blocking protection
80 dB
Intermodulation protection
75 dB
Intercept 3° order IP3in
+15 dBm
Documento Riservato - non divulgabile senza autorizzazione
Pag. 15 / 31
DMR repeater 24/01/2011
Distortion
Versione 1.3
<2 %
-53 dBp @25 KHz
Noise
-47 dBp @12.5 KHz
-60 dBp (with voice search option)
Frequency stability
0.5 p.p.m.
Documento Riservato - non divulgabile senza autorizzazione
Pag. 16 / 31
DMR repeater 24/01/2011
Versione 1.3
4.4.3 FREQUENCY BANDS
Model
Frequency band
RA-900
UHF – HH => 865-925 MHz
RA-450
UHF – H => 410-440 MHz
RA-450
UHF – L => 430-470 MHz
RA-160
VHF – H => 145-174 MHz
RA-080
VHF – L => 68-88 MHz
4.4.4 COMMUTATION BAND (WITHOUT DUPLEXER)
Band
TX
RX
UHF – H
30 MHz
14 MHz
UHF – L
30 MHz
12 MHz
VHF – H
28 MHz
28 MHz
VHF – L
20 MHz
20 MHz
4.4.5 BRANCHING REQUIREMENTS
4.4.5.1 TX to antenna duplex isolation requirements @10W TX RF power
RX main
TX
Documento Riservato - non divulgabile senza autorizzazione
Pag. 17 / 31
DMR repeater 24/01/2011
Band
+/-40MHz
Versione 1.3
+/-9MHz
+/-4.5MHz
+/-3MHz
+/-1.5MHz
+/-0.8MHz
UHF – HH
75dB
UHF – H/L
75dB
75dB
VHF – H
75dB
75dB
75dB
78dB
81dB
85dB
VHF – L
75dB
75dB
75dB
75dB
78dB
81dB
4.4.5.2 Suggested RX max input limits on unwanted signals
TX
RX main
Band
+/-1MHz
+/-500KHz
+/-100KHz
+/-50KHz
+/-25KHz
+/-12.5KHz
UHF – HH
-32dBm
-43dBm
-45dBm
-47dBm
-49dBm
-58dBm
UHF – H/L
-32dBm
-41dBm
-43dBm
-44dBm
-48dBm
-56dBm
VHF – H
-32dBm
-40dBm
-42dBm
-43dBm
-47dBm
-54dBm
VHF – L
-32dBm
-36dBm
-38dBm
-40dBm
-43dBm
-50dBm
4.5
OTHER SPECIFICATIONS
Documento Riservato - non divulgabile senza autorizzazione
Pag. 18 / 31
DMR repeater 24/01/2011
Versione 1.3
4.5.1 ENVIRONMENTAL PARAMETERS
Operating Temperature
-25 ÷ +55 °C
Storage Temperature
-40 ÷ +70 °C
Relative Humidity
Max 80% not condensed
4.5.2 POWER SUPPLY
11 - 15 Vcc (neg. ground)
19 – 36 Vcc (floating ground)
38 – 60 Vcc (floating ground)
Nominal Voltage
Max ripple
30 mVpp
Polarity reversal protection
Short-circuit protection
-70 V
Electronic protection with automatic restore and double fuse on
input line
Power consumption
TX: 55 W @20W RF
RX: 8 W
4.5.3 MECHANICAL CHARACTERISTICS
Dimensions
Weight
128 x 426 x 280 mm
1/2 rack 19” x 3TU x 280 mm mounting
6.0 Kg
4.5.4 AUDIO BALANCED INTERFACES
Interface type
2/4 wires isolated balanced line on RJ45 socket
Line isolation
1500 V
Used audio bandwidth
Input/output Impedance
300÷3400 Hz
600 Ohm
Documento Riservato - non divulgabile senza autorizzazione
Pag. 19 / 31
DMR repeater 24/01/2011
Versione 1.3
Side tone reflection
< - 20 dB
Output nominal level
-20 .. 0 dBm
Input nominal level
-20 .. 0 dBm
Hang line current
10..50 mA
Level adjust
software by 0.1dB step
Ring detect
60..120 Vpp @25Hz
Ring generator (option)
90Vpp @25Hz
Release tone detection
3 pulses of 425Hz @50% duty 250ms/250ms
5.1
EQUIPMENT INSTALLATION AND MAINTENANCE
CONNECTIONS AND PINOUTS
RA-XXX base-stations require a reduced set of connections for normal working conditions (power supply, with
optional “power good” and “inhibit” controls, antennas, eventual ethernet link for remote control or for multisite link). The transceiver is equipped with other sockets in order to connect it to auxiliary equipment, like
other transceivers, multi-receivers, audio interfaces, remote site control devices, fan cooler, and so on.
On the front side of the equipment there are only the 10BT/100TX ethernet connector for the remote control
of the equipment and for data/audio packets communication, the power on/off switch and the LEDs for
monitoring the status of the equipment. All other connectors are placed on the back side of the transceiver.
The following picture shows the fundamental connections in red color and the optional ones in blue color.
Documento Riservato - non divulgabile senza autorizzazione
Pag. 20 / 31
DMR repeater 24/01/2011
RS232
port
Versione 1.3
FAN
activation
6V-12V output,
max 200mA
Matrix
connector
Main RX
antenna
MTCH
synchronous
serial interface
GPS
antenna
External
synchronism
input
Main RX /
TX antenna
Inhibit /
Power_good
contacts
GSM /
GPRS
antenna
Diversity RX
antenna
fuses
I/O
contacts
Alarm
outputs
Audio line
interface
Analog
inputs
12Vcc
Power
supply
The following connections are available (for each one, a picture of the connector and the related schematic
diagram of back plane PCB are shown):
∞ Power Supply: 13.2Vdc with negative to ground, or optionally 24Vdc or 48Vdc isolated. The equipment
is protected from polarity inversion. Two automotive type 10A fuses work against accidental short
circuits. The connector has 3 poles (+Vin, rack ground, -Vin) with 5.08mm pitch
3 - 5.08pitch
FUS-AUTO-10A
P12
F2
-Vin
FUS-AUTO-10A
F1
+Vin
∞ Power supply control: normally closed optically isolated “PG” (Power Good) contact ensures the
presence of internal correct supplies; “INH” (Inhibit) contact should be kept closed/open to switch
off/on the equipment. Input contact is internally polarized with +/-12V.
P6
MCV 0,5/ 4-G-2,5
PG_A
PG_B
/INHIBIT
COM_OPTO
∞ Antennas: up to 5 antenna connectors can be mounted according to the specifications of equipment.
1. A female N-type connector is connected to the output of the duplexer (if present) or to
the output of the TX (if branching is not mounted inside the equipment);
2. A female BNC-type connector (above the N-type one) is present if duplexer is not
mounted inside the equipment. It is connected to main RX;
Documento Riservato - non divulgabile senza autorizzazione
Pag. 21 / 31
DMR repeater 24/01/2011
Versione 1.3
3. A female BNC-type connector (below the N-type one) is present if the base station is
equipped with the diversity receiver. This connector is directly connected to the input of
the diversity receiver, without any cavity filter/isolation inside the equipment. Care
should be taken in designing external branching and radiant system;
4. A female SMA-type connector for embedded GPS receiver. The equipment supplies
5Vdc through this connector for the remote active antenna (which is requested with a
minimum gain of 20dB and possibly equipped with a rejecting filter for out-of-band
spectral components);
5. A female SMA-type connector for GSM/GPRS embedded transceiver. A passive antenna
is required. (The SIM holder is mounted inside I/O module.).
Main RX
antenna
GPS
antenna
Duplex antenna /
TX antenna
GSM /
GPRS
antenna
Diversity RX
antenna
∞ COM port: 9 poles D-SUB type socket, connected to an optional RS232 serial port (115.2Kbit/sec,
8,N,1) for remote controlling the equipment by a PC. This is a secondary access port to the base
station, auxiliary/alternative respect to the main ethernet port. The RS232 driver is mounted on the
I/O module.
SJV9
J4
RX-PC
RTS
TX-PC
CTS
TX_232
cts_232
RX_232
rts_232
∞ “Fan” and “Auxiliary power supply output”: the first is an active low, open collector type contact, not
isolated, which can activate an optional external cooling system if RF power amplifier temperature
would rise over 90°C. In normal ambient and working conditions, no cooling system is required. The
second connector supplies 12Vdc 200mA and 6Vdc 200mA (not isolated) for eventual auxiliary devices
MCV 0,5/ 4-G-2,5
MCV 0,5/ 2-G-2,5
P2
HI-TEMP
P1
6V_SERV
12V_SERV
Documento Riservato - non divulgabile senza autorizzazione
Pag. 22 / 31
DMR repeater 24/01/2011
Versione 1.3
∞ “MTCH”: two 8 poles RJ45 connectors (connected in parallel) give access to internal digital audio
multichannel (synchronous, TDMA, 4Mbit/s speed, serial interface with custom protocol). These
connectors are used to implement any particular system and network architectures which require the
base station to be connected to other devices equipped with the same MTCH interface.
RJ45
J2
11
DR0_A
DT0/DR0_A
SCLK0_B
RFS0_A
DR0_B
SCLK0_A
DT0/DR0_B
RFS0_B
12
∞ Analog inputs: a 4 poles connector with 2 not isolated analog inputs, one for current (dc, from 0 to
20mA) and one for voltage (dc, from 0 to 20V referred to GND). Current inputs of different
equipments ca be connected in series; voltage inputs of different equipment can be connected in
parallel.
MCV 0,5/ 4-G-2,5
P5
AN_I_INAN_I_IN_+
AN_V_IN
∞ AF line interface: a 8 poles connector to connect the base station to a telephone or console line (both
2 or 4 wire lines, also with E and M criteria) to monitor analog traffic only or for synchronization aim.
Starting from the top, the pinout is as following: output line (use this contacts in case of 2 wire line –
bidirectional -), squelch input contact (optically isolated, normally open), PTT output contact (optically
isolated, normally open, internally polarized with +/-12V), input line(only for 4 wire line).
MCV 0,5/ 8-G-2,5
P9
BF0-OUT-A
BF0-OUT-B
SQ_OUT_0
COM_SQ_OUT_0
PTT_IN_0
COM_OPTO
BF0-IN-A
BF0-IN-B
∞ Digital I/O: a 8 poles connector with 4 optically isolated digital contacts, 2 outputs (in the upper part,
normally open) and 2 inputs (in the lower part, normally closed). Input contacts are internally
polarized with +/-12V.
MCV 0,5/ 8-G-2,5
P10
1_OUT
COM_1_OUT
2_OUT
COM_2_OUT
1_IN
COM_OPTO
2_IN
COM_OPTO
∞ Alarm outputs: a 4 poles connector with 2 optically isolated digital contacts (normally open). Alarm 2
output will be closed if the base station undergoes a temporary out of service or if a slight problem
happens (warning); alarm 1 output will be closed during power on of the station or if a heavy problem
happens (stable out of service).
MCV 0,5/ 4-G-2,5
P13
COM_ALR_2_OUT
ALR_2_OUT
COM_ALR_1_OUT
ALR_1_OUT
Documento Riservato - non divulgabile senza autorizzazione
Pag. 23 / 31
DMR repeater 24/01/2011
Versione 1.3
∞ “Matrix” connector: a 20 poles connector (2x10, pitch 2.54mm) and a coaxial MCX-type connector
with a set of signals which can be used to implement any particular system and network architectures
which require the base station to be connected to other devices equipped with the same MTCH
interface.
SP20
P4
COM_MS_RX
URES
SYNC_12M8
RESERVED
LINE_OPTO
10
12
14
16
18
20
RX/TX
6V_SERV
NOR/RIS
COM_MS_TX
12V_SERV
RESERVED
PPS_GPS
COM_OPTO
ON-LINE
6V_SERV
12V_SERV
11
13
15
17
19
J9
LO_TEST
JCOAXMINI90
J6
JCOAXMCX90
SYNC_IN
∞ SYNC IN: a MCX coaxial connector for eventual external synchronization input signal. Normally this
input is unused, it is needed for special applications which require an external synchronization source
(sinusoidal, at 12.8MHz, with level between -10 and 0 dBm).
Documento Riservato - non divulgabile senza autorizzazione
Pag. 24 / 31
DMR repeater 24/01/2011
Versione 1.3
For example, the following picture shows how two repeaters should be connected to implement a
simulcast network with ethernet links.
Main RX /
TX antenna
Diversity RX
antenna,
if needed
GSM/
GPRS
DMR master
Main RX /
TX antenna
GPS and
GSM/GPRS
antenna
LA
Diversity RX
antenna,
if needed
GPS and
GSM/GPRS
antenna
GSM/
GPRS
GPS
GPS
DMR slave
ca
le
LA
ca
le
LAN cable
Ethernet SWITCH
Remote control PC
“DMR Manager”
In case of UHF links, 2 transceivers are needed for each site, one for local broadcasting and the other
for the link between master and satellite. They can be mounted into the same rack 19” 3U. The
following picture shows the back side of a RF linked satellite.
Documento Riservato - non divulgabile senza autorizzazione
Pag. 25 / 31
DMR repeater 24/01/2011
Versione 1.3
RS232
port
MTCH terminations to be connected
together by an ethernet cord
FAN
activation
GPS
antenna
6V-12V output,
max 200mA
FAN
activation
RS232
port
6V-12V output,
max 200mA
Main RX /
TX antenna
Main RX /
TX antenna
GSM /
GPRS
antenna
I/O
contacts
Analog
inputs
Alarm
outputs
Audio line
interface
12Vcc
Power
supply
Inhibit /
Power_good
contacts
Analog
inputs
Alarm
outputs
I/O
contacts
Audio line
interface
Diversity RX
antenna
12Vcc
Power
supply
Inhibit /
Power_good
contacts
For this example, the following picture shows how two repeaters should be connected to implement a
simulcast network with UHF links. Two ethernet patch cord are needed to connect together the
MTCH ports and the ethernet ports of the two radios; they are represented in pink color.
Main RX /
TX antenna
(broadcast)
Diversity RX
antenna
(broadcast),
if needed
Main RX /
TX antenna
(link)
GPS and
GSM/GPRS
antenna
GSM/
GPRS
MTCH cable
LAN cable
Main RX /
TX antenna
(broadcast)
Diversity RX
antenna
(broadcast),
if needed
GPS
Main RX /
TX antenna
(link)
GPS and
GSM/GPRS
antenna
GSM/
GPRS
GPS
MTCH cable
DMR master
LAN cable
DMR slave
Documento Riservato - non divulgabile senza autorizzazione
Pag. 26 / 31
DMR repeater 24/01/2011
5. 2
Versione 1.3
EQUI PMEN T ST A R T UP, R UN N I NG A N D A LA R MS: I N DI C A T OR LA MPS
The base stations of RA-xxx series are designed to reduce as much as possible the maintenance work. To this
aim, specific solutions have been implemented to prevent aging drifts.
Each time the base station is switched on, a self-calibration process is performed in order to finely tune the
modulation and the demodulation parameters. This process checks the total loop BF-TX-RX-BF by looping the
synthesizer output of the TX on the input of the RX and the DSP unit can store the results into flash memory
and update the older ones which have been previously saved. The correct results of a calibration process are
symptom of an optimal tune of the radio transceiver. If the calibration process ends with errors, the
transceiver can anyway work correctly by loading the older tuning parameters and the newer ones are not
saved.
On the frontal panel of the RA-xxx base stations, there are some LED lamps for monitoring the status of the
equipment. They have different meanings, during power on process, respect to normal running condition.
Here following, a description of the meaning of the LEDs, grouped module by module. In general, if the
equipment works correctly, all leds are off or green; if a warning arises, one or more leds start flashing in red
color; if a problem or an alarm arises, one or more leds are red. (An exception should be made for eventual
leds which show the status of line output criteria: they are red if the corresponding criteria are enabled).
5.2.1 PSU
When the base station is switched on, the 2 leds of PSU module should be green both:
∞ the upper led is red if the supplied input voltage is too low or too high; it is off in case of inverted
polarity of connection to power supply system; it is green if the supplied input voltage belong to the
correct working range;
∞ the lower led is green if the secondary internal voltages are correctly supplied by PSU module,
otherwise it is off.
5.2.2 DSP
When the base station is switched on, DSP module performs a booting process, during which the upper 4 leds
are orange; the lower 2 leds respectively monitor the activity through ethernet connection (the 5th led flashes
with orange color during data communication) and the connection to ethernet network (the 6th led is green if
the connection is established), therefore they are independent from the logical status of the module. At the
end of the booting process, the DSP module executes the following steps in sequence, which are also visually
indicated by leds:
∞
∞
∞
∞
∞
∞
FW uploading to clock generator (3rd led flashes in orange color);
FW uploading to DSP and reset of peripheral modules (2nd led flashes in orange color)
DSP startup (1st led flashes in orange color)
RX self-calibration(2nd led flashes in red color)
TX self-calibration (1st led flashes in red color)
TX
RX loop self-calibration (3rd led flashes in red color)
Documento Riservato - non divulgabile senza autorizzazione
Pag. 27 / 31
DMR repeater 24/01/2011
Versione 1.3
∞ Frequency setup of working channel (1st led flashes in red color in case of fine calibration of
parameters)
At this point the DSP reaches its normal running status and the leds behave as follows:
∞ 1st upper led: it flashes in green color if calibration of TX failed; it is green during transmission on TS1;
it flashes in red color if multichannel is enabled but the DSP cannot receive data correctly (this
function will be assigned to the 2nd led in future SW version); otherwise it is off;
∞ 2nd led: it flashes in green color if calibration of RX failed; it is green during transmission on TS2; it
flashes in red color if multichannel is enabled but the DSP cannot receive clock correctly (this function
will be assigned to the 3rd led in future SW version); otherwise it is off;
∞ 3rd led: it flashes in green color if calibration of TX
RX loop failed; it is green during reception from
TS1; otherwise it is off;
∞ 4th led: it flashes in green color if the system clock is locked to the synchronism source; it is green
during reception from TS2; it flashes in red color if the DSP is not locked to the synchronism source as
set in “AFC” routine; otherwise it is off;
∞ 5th led: it flashes in orange color during data communication through ethernet port; otherwise it is off;
∞ 6th led: it is green if the ethernet connection is established; otherwise it is off.
During analog transmission (or reception), both the leds related to transmission (or reception) on TS1 and TS2
are green, because both the timeslot are busy during analog communication.
5.2.3
RX
RX module is equipped with two leds:
∞ the upper led flashes very fast in green-red color during data reception-transmission through control
serial port of the module (during FW upload process on peripheral microprocessor); it is red in case of
unlock of the upper local oscillator which is used to tune the RX; otherwise it is off;
∞ the lower led flashes in red color if there is no application (main) FW uploaded to peripheral
microprocessor; it flashes in green color during start-up booting process; it is red in case of unlock of
at least one of the IF local oscillators; otherwise it is off.
5.2.4 TX
TX module is equipped with two leds:
∞ the upper led flashes very fast in green-red color during data reception-transmission through control
serial port of the module (during FW upload process on peripheral microprocessor); it is red in case of
unlock of the local oscillator or during transmission if the generated RF power is less than a half of its
set value; it is green during transmission with a greater RF power than 10W; otherwise it is off;
∞ the lower led flashes in red color if there is no application (main) FW uploaded to peripheral
microprocessor; it flashes in green color during start-up booting process; it is red in case of excessive
SWR and consequent forced interruption of transmission; it is green during transmission with a lower
(or equal) RF power than 10W; otherwise it is off.
5.2.5 I/O
I/O module is equipped with eight leds, of which the upper 6 reflect the status of corresponding digital I/O
contacts that are present on the back side of the equipment, while the lower 2 reflect the status of the
embedded GSM/GPRS-GPS device. They behave as follows:
Documento Riservato - non divulgabile senza autorizzazione
Pag. 28 / 31
DMR repeater 24/01/2011
Versione 1.3
∞ the upper led is red if a heavy problem happens to the base station or during its booting process
(meaning a stable out of service status); the corresponding alarm 1 is active; otherwise the led is off;
∞ the 2nd led is red if the base station undergoes a temporary out of service (example during a channel
change) or if a slight problem happens (warning); the corresponding alarm 2 is active; otherwise the
led is off;
∞ the 3rd led is green if the output contact 1 is active (normally open);
∞ the 4th led is green if the output contact 2 is active (normally open);
∞ the 5th led is green if the input contact 1 is active (normally closed);
∞ the 6th led is green if the input contact 2 is active (normally closed);
∞ the 7th led flashes in green color if PPS signal is generated (Attention: after the first reception of a valid
GPS signal for generating PPS signal, this signal is always generated by the module, it is eventually
locked to local clock of the divice in case of temporary unlock with GPS reference. The DSP module
checks its effective validity); otherwise it is off;
∞ the 8th led flashes in green color if embedded GSM/GPRS module is enabled; it flashes fast if the SIM
card is missing, slower if the SIM card is present; it is red during transmission of GSM bursts;
otherwise it is off.
5. 3
GENERAL RECOMMENDATIONS AND NOTES
5.3.1 IMPROPER USE
It is recommended to install the equipments in closed cabinet, to allow only authorized people to access to
them, in order to avoid handling or improper use of equipments and to avoid accidental contact with hot
surfaces.
5.3.2 THERMAL DISSIPATION
Outlet cabinet containing the equipments should be designed to ensure a good internal air flux for heating
dissipation. A free slot of at least 1UT is recommended between two near equipments.
In case RF transmitter is set for its maximum power, it is active with a duty-cycle near to 100% and ambient
temperature could be above 40°C, a larger respect area must be considered around the rack and an air forced
cooling system should be eventually designed (“FAN” contact of the equipment can be used to switch on and
off cooling system). The transmitter is protected against over-temperature: if the RF mosfet temperature
arises over 90°C, the microprocessor will automatically decrease the generated RF power in order to make the
amplifier work in safety conditions. The nominal RF power will be restored as soon as the mosfet temperature
will decrease below 60°C.
5.3.3 POWER SUPPLY SYSTEM
Internal power supply voltage is nominally set to 13.2V dc from battery, with negative pole connected to
ground, and it is protected against polarity inversion, over-voltage, under-voltage, short-circuits. Isolated PSU
modules can be optionally supplied for 12V/24V/48V dc input voltage.
Documento Riservato - non divulgabile senza autorizzazione
Pag. 29 / 31
DMR repeater 24/01/2011
Versione 1.3
The equipment is designed to be powered by a safe supply source which grants a double insulation of output
voltage from dangerous voltages. The electric plant must contain a switch to cut off power supply lines,
according to national law and directives.
It is recommended to use power supply sources with low impedance output stage to make the hot swap
controller of PSU properly work. For example, if power supply has an output filter with an inductive equivalent
impedance, a capacitor can be added in parallel in order to reduce the resulting output impedance.
Power supply cable dimensions must be calculated for a maximum current absorption of 7A @13.2V DC, or 4A
@24V, or 2A @48V, in order to avoid significant voltage drop, especially after fast transient. They should be
protected by a fuse or a short circuit protection system which should be placed as near as possible to power
supply source.
The transceiver is equipped with a couple of automotive type fuses, placed near power supply input
connector, for short circuits protection. This type of fuses is designed for battery up to 55 Ah; for bigger
battery power, other more effective devices should be placed before the transceiver to grant a correct power
cut off.
It is also recommended to connect a good ground reference to the rack and to its metal components, by using
both central pin of power supply connector and the screw on the right side of the rack. A second screw for
ground connection is place on the back side of the rack.
5.3.4 ANTENNA
Antenna discharger are recommended to prevent damages due to eventual atmospheric discharges. These
devices should be placed on antenna connection cable, just before equipments installation shelter, and they
must be connected to an optimum ground reference.
Attention must be paid also to connect the eventual diversity receiver to the radiant system: the input of this
receiver is directly connected to BNC connector on the back side of the rack, without any filter. The
corresponding antenna must be placed far enough from the transmitting antenna in order to avoid receiver
desensitization and to get the correct isolation. To avoid any problem, it is recommended to insert a notch or a
pass-band cavity to protect the receiver.
If an external branching is connected to the equipment, it must be designed to ensure the needed isolations
between transmitter and receivers.
5.3.5 AF INTERFACE
If a 2/4W telephone line is connected to the equipment, external primary discharges are recommended to
prevent damages due to eventual atmospheric discharges on the line. The internal AF interface is protected
only by secondary dischargers.
5.3.6 MANUAL SETTINGS
The equipments of RA-xxx series are designed to minimize the set of needed hardware settings. Before
installing the equipments the following manual settings must be verified if digital I/O and AF interface are used
respectively:
Documento Riservato - non divulgabile senza autorizzazione
Pag. 30 / 31
DMR repeater 24/01/2011
Versione 1.3
∞ voltage polarity, used to supply the optically isolated digital input contacts: inside PSU module, a 4
poles dip-switch allows to set the polarity, according the following table:
1 ON
2 ON
3 OFF
4 OFF
1 OFF
2 OFF
3 ON
4 ON
+12V
-12V
∞ AF line interface characteristics: inside I/O module, a 2 pole dip-switch allows to set the line type (2W
or 4W) and the input impedance of eventual 4W line (600 ohm or high), according the following table:
1 ON
1 OFF
2 ON
2 OFF
Zin (4W) = 600 ohm
Zin (4W) = High
2W
4W
5.3.7 SELF-CALIBRATION PROCESS
During self-calibration process internal parameters of modulator and demodulators are tuned by generating a
signal through the synthesizer of the transmitter, by automatically connecting its output to the input of the
receiver and by analyzing the received signal. If a strong signal is received by the external antenna during selfcalibration, it is possible that the process ends with errors (a corresponding “warning” alarm will be displayed
on both frontal leds and monitor of PC for remote control). In this case the DSP will load from flash memory
the previously saved parameters without any problem for the transceiver.
To obtain better results from self-calibration process, it is recommended to set the calibration frequency as
near as possible to the transmitter frequency; if there is a range of allowed frequencies for transmission, it is
recommended to set the centre of this range as the calibration frequency.
5.3.8 PPS SIGNAL
For applications in simulcast networks where the source of synchronization is the PPS signal by GPS, if this
signal is missing, the radio coverage of the areas which are reached by several repeaters with the same field
strength, is not ensured. Attention must be paid in choosing and placing the GPS antenna.
Documento Riservato - non divulgabile senza autorizzazione
Pag. 31 / 31

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Count                      : 31
Warning                         : XMP format error (no closing tag for L)
Producer                        : Nitro PDF PrimoPDF
Create Date                     : 2011:01:25 13:04:48-01:00
Modify Date                     : 2011:01:25 13:04:48-01:00
Title                           : Microsoft Word - ENB32 - DMR repeater user manual 1v2.doc
Creator                         : PrimoPDF http://www.primopdf.com
Author                          : mauro

EXIF Metadata provided by EXIF.tools