Radwin RW2030 Outdoor radio unit operating in 3.65 GHz band User Manual STW

Download:
Mirror Download [FCC.gov]
Document ID	1570439
Application ID	yHSrM8izhH+wCX77YhL7VA==
Document Description	Revised User manual part 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	179.42kB (2242710 bits)
Date Submitted	2011-10-30 00:00:00
Date Available	2012-05-16 00:00:00
Creation Date	2011-10-24 08:45:51
Producing Software	Acrobat Distiller 10.1.1 (Windows)
Document Lastmod	2011-10-27 13:33:59
Document Title	STW
Document Creator	FrameMaker 10.0.1
Document Author:	DAF

Chapter 6
Site Configuration
The Site Configuration dialog panels are used to configure parameters,
which may differ between both sides of the link.
The parameters configured using the Site Configuration dialog panels
include (among others):
•
System settings
•
Air interface - Transmit (Tx) power and antenna
•
Network management including VLAN
•
Security settings
•
Date and time
•
Hub or Bridge mode
In addition, the Link Site Configuration panels include several information
windows:
•
Inventory - link hardware and software model details
•
External alarms indicators
The Operations dialog offers a “doorway” to jump into installation mode
reverting to factory settings.
The Site Configuration dialog has its own main menu with the following
extra functionality:
•
Backup configuration parameters to a text file
•
Restore configuration from a previously backed up configuration file
•
Enable/disable the site ODU buzzer
•
Jump back into installation mode keeping current configuration settings
Configuring the Site
Editing the Configuration Parameters by Site
You can edit the configuration parameters for each site individually. The following functions are available from the left side of the dialog box.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-1
Editing the Configuration Parameters by Site
Chapter 6
Figure 6-1: Configuration Dialog Box
Functions on the left of the dialog box:
System
Edit the contact person and location details.
View the system details
Air Interface
Change the transmit power, cable loss, antenna
type and settings
Inventory
View the hardware and software inventory
(release numbers, model identification, MAC
address)
Management
Configure the IP address, Subnet Mask, Default
Gateway, the Trap Destination and VLAN
Security
Change the Community Values and the Link
Password
Date and Time
Set the date and time of the link from an NTP
servers otherwise
Advanced
Choose Hub or Bridge ODU mode, set the
Ethernet ports configuration, set the external
alarm inputs, restore factory settings
Functions at the top of the dialog box:
Backup
Save the current configuration to an .ini file
Restore
Restore the link configuration from the .ini file
created by the backup
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-2
Viewing Air Interface Details
Chapter 6
Installation
Mode
Return to Installation Mode for the entire link.
Mute
Mutes the alignment tone in installation mode.
Reactivate the beeper during alignment.
Selecting the Mute check box before clicking
the Install Mode button mutes the Beeper.
 To edit the Configuration Parameters:
1. Click the required site button on the main tool bar of the RADWIN Manager
OR
Click Configuration from the main menu and choose a site to configure.
The Configuration dialog box opens (see figure 6-1 above).
2. Choose the appropriate item in the left hand list to open a dialog box.
3. Click Apply to save changes.
In subsequent instructions, we will simply say “Choose a site to configure”
on the understanding that the foregoing procedure is implied.
Viewing Air Interface Details
Click the Air Interface item in the left hand list. A window similar to the following appears:
Figure 6-2: Air interface details
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-3
Changing the Transmit Power
Chapter 6
Changing the Transmit Power
Each site can have a different transmit power level.
 To change the Transmit Power:
1. Choose a site to configure.
The Configuration dialog box opens.
2. Choose Air Interface (see figure 6-3).
3. Choose the required Transmit (Tx) Power Level.
4. Click Apply to save the changes.
Figure 6-3: Changing the Transmit Power
The same considerations apply here as were noted in the Installation
procedure on page 4-23.
Note
Site Management: IP Address and VLAN
Configuring the ODU Address
Each site must be configured separately, first site A then site B.
 To define the Management Addresses:
1. Choose a site to configure.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-4
Configuring VLAN Settings
Chapter 6
The Configuration dialog box opens:
Figure 6-4: Management Addresses - Site Configuration dialog box
5. Choose Management.
6. Enter the IP address of the ODU in the IP Address field.
If performing configuration from the RADWIN Manager, the IP address is
that entered from the login screen.
Note
7. Enter the Subnet Mask.
8. Enter the Default Gateway.
9. Enter the Trap Destination. This could be the IP address of the managing
computer. The events log will be stored at this address.
10.Click Apply to save the changes.
Configuring VLAN Settings
VLAN Management enables separation of user traffic from management
traffic whenever such separation is required. It is recommended that both
sides of the link be configured with different VLAN IDs for management traffic.
 To enable VLAN management:
1. Click Configuration from the main menu.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-5
Configuring VLAN Settings
Chapter 6
2. Choose a site to configure. If you are configuring both sites, choose site
B first.
3. Choose Management.
4. Open the VLAN tab.
5. Check the Enabled box.
6. Enter a VLAN ID. Its value should be between 1 and 4094.
After entering the VLAN ID, only packets with the specified VLAN ID are
processed for management purposes by the ODU. This includes all the
protocols supported by the ODU (ICMP, SNMP, TELNET and NTP). The
VLAN priority is used for the traffic sent from the ODU to the managing
computer. Using VLAN for management traffic affects all types of management connections (local, network and over the air).
7. Enter a Priority number between 0 and 7.
8. Change the VLAN ID and Priority of the managing computer NIC to be
the same as those of steps 6 and 7 respectively.
9. Click Apply or OK.
Figure 6-5: Configuring management traffic VLAN Settings
Caution
Changing this parameter causes the RADWIN Manager to immediately
disconnect.To avoid inconvenience, you should verify the change by
setting the VLAN only to one ODU, and only after verifying proper
management operation, change the other ODU VLAN setting.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-6
Setting the Date and Time
Chapter 6
Lost or forgotten VLAN ID
If the VLAN ID is forgotten or there is no VLAN traffic connected to the
ODU, then reset the relevant ODU.
During the first two minutes of connection to the ODU uses management
packets both with and without VLAN. You may use this period to reconfigure
the VLAN ID and priority.
Setting the Date and Time
The ODU maintains a date and time. The date and time should be synchronized with any Network Time Protocol (NTP) version 3 compatible server.
During power-up the ODU attempts to configure the initial date and time
using an NTP Server. If the server IP address is not configured or is not
reachable, a default time is set.
When configuring the NTP Server IP address, you should also configure the
offset from the Universal Coordinated Time (UTC). If there is no server
available, you can either set the date and time, or you can set it to use the
date and time from the managing computer. Note that manual setting is not
recommended since it will be overridden by a reset, power up, or synchronization with an NTP Server.
The NTP uses UDP port 123. If a firewall is configured between the ODU
and the NTP Server this port must be opened.
Note
It can take up to 8 minutes for the NTP to synchronize the ODU date and
time.
 To set the date and time
1. Determine the IP address of the NTP server to be used.
2. Test it for connectivity using the command (Windows XP), for example:
w32tm /stripchart /computer:216.218.192.202
You should get a continuous response of times, each a few seconds
apart.
3. Choose a site to configure.
The Configuration dialog box opens.
4. Choose Date & Time:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-7
Setting the Date and Time
Chapter 6
Figure 6-6: Date and Time Configuration
5. If entering an IP address for the NTP Server, click Clear, and then enter
the new address.
6. Set your site Offset value in minutes ahead or behind GMT1.
7. To manually set the date and time, click Change and edit the new values.
Figure 6-7: Change Date and Time
If you used an NTP Server, you will see a window like this:
1. Greenwich Mean Time
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-8
Ethernet Properties
Chapter 6
Figure 6-8: Date and Time configured from an NTP Server
8. Click OK to return to the Configuration dialog.
Ethernet Properties
Configuring the Bridge
Bridge configuration is required in various network topologies, such as protection (1+1) and ring applications. The bridge configuration parameters
are located under the Advanced tab of the Site Configuration dialog box:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-9
Configuring the Bridge
Chapter 6
Figure 6-9: Bridge Configuration - Site Configuration dialog box
ODU Mode
This parameter controls the ODU mode with two optional values,
•
Hub Mode - in Hub mode the ODU transparently forwards all packets
over the wireless link.
•
Bridge Mode - In Bridge mode the ODU performs both learning and
aging, forwarding only relevant packets over the wireless link. The
aging time of the ODU is fixed at 300 seconds.
Changing these modes requires system reset.
Note
IDU Aging time
This parameter controls the IDU aging time.
The aging time parameter controls the time after which each MAC address
is dropped from the MAC address learning table.
The default value is 300 seconds.
Note
•
Any change to these parameters is effective immediately.
•
Each side of the link can be configured separately.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-10
Configuring Ethernet Ports Mode
Chapter 6
The following table shows the appropriate configuration for several common
scenarios. Both link sites must be configured with the same parameter:
Table 6-1: ODU mode configuration for common
ODU
Mode
IDU Aging
Time
Standard (Default) Configuration for
Ethernet Applications
Bridge
300 sec
Rapid network topology changes
where fast aging is required
Hub
1 sec
Ethernet Hub
Hub
N/A
Ethernet Bridge
Bridge
N/A
Scenario
Configuring Ethernet Ports Mode
The ODU Ethernet port is configured to auto-detect by default and may not
be changed.
The ODU Ethernet port mode is configurable for line speed (10/100BaseT)
and duplex mode (half or full duplex).
An Auto Detect feature is provided, whereby the line speed and duplex
mode are detected automatically using auto-negotiation. Use manual configuration when attached external equipment does not support auto-negotiation. The default setting is Auto Detect.
Caution
You should not reconfigure the port that is used for the managing computer
connection, since a wrong configuration can cause a management
disconnection or Ethernet services interruption.
 To configure the Ethernet Mode:
1. From the Configuration menu, choose the site to reconfigure.
The Site Configuration dialog box opens.
2. Click Advanced | Ethernet.
3. In the Ethernet Ports Configuration pane, use the drop-down menu to
choose the configuration.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-11
Setting the Maximum Information Rate
Chapter 6
4. Click Apply to save the changes.
It is possible to close the Ethernet service by disconnecting the Ethernet
port.
Note
If you close the port, you may subsequently be unable to access the
device. If this should occur, a workaround is as follows:
•
Connect the system from the remote site
•
Connect via other Ethernet port (of the IDU)
•
Power down the equipment and connect immediately after power
up (the fastest way is to enter install mode)
Setting the Maximum Information Rate
The maximum Ethernet throughput of the link can be limited. The default
setting is Not Limited (see figure 6-9 above), where the highest information rate available for the link conditions and settings is used.
 To limit the Ethernet information rate:
1. From the Configuration menu, choose the site to reconfigure.
2. Click Advanced | Ethernet
The Configuration dialog box opens.
3. In the Information Rate pane, use the drop-down menu to choose the
maximum Information Rate.
4. Choose Other to define the throughput with 1 Kbps resolution
5. Choose Not Limited for the highest information rate possible for the
link conditions and settings
6. Click Apply to save the changes.
Displaying the Inventory
 To view the inventory data
1. Choose a site from the main menu.
The Configuration dialog box opens.
2. Choose Inventory (figure 6-10).
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-12
Security Features
Chapter 6
Figure 6-10: Inventory Screen
Security Features
The Security dialog enables you to change the Link Password and the SNMP
Communities details:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-13
Changing the Link Password
Chapter 6
Figure 6-11: Available security features
Changing the Link Password
This item is only available when the link is down. Otherwise, it works the
same way as the corresponding item on page 4-16.
RADWIN Manager Community Strings
The ODU communicates with the application using SNMPv1 protocol. The
protocol defines three types of communities:
•
Read-Only for retrieving information from the ODU
•
Read-Write to configure and control the ODU
•
Trap used by the ODU to issue traps.
The Community string must be entered at login. The user must know the
password and the correct Community string to gain access to the system. A
user may have read-only privileges.
It is not possible to manage the ODU if the read-write or the read Community values are forgotten. A new Community value may be obtained from
RADWIN Customer Support for the purpose of setting new Community; the
serial number or the MAC address of the ODU must be supplied.
Note
The RADWIN Manager uses the Read Community strings public for the site
Al ODU and public-remote for the site B ODU. It uses Write Community
strings netman for the site A ODU and netman-remote for the site B
ODU. These are the factory defaults.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-14
RADWIN Manager Community Strings
Chapter 6
The read-write Community strings and read-only Community strings have a
minimum of five alphanumeric characters. (bru1 and bru4097 are not permitted). Changing the trap Community is optional and is done by clicking
the check box.
Editing Community Strings
The Community change dialog box is available from the Configuration |
Security tab. Both read-write and read-only communities must be defined.
On logging on for the first time, use the following as the current Community:
•
For Read-Write Community, use netman.
•
For Read-Only Community, use public.
•
For Trap Community, use public
 To change a Community string:
1. From the Configuration dialog box, choose the Security tab.
2. Type the current read-write Community (default is netman).
3. Choose the communities to be changed by clicking the check box.
4. Type the new Community string and re-type to confirm.
5. Click OK to save.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-15
RADWIN Manager Community Strings
Chapter 6
Figure 6-12: Changing the Community String
Forgotten Community string
If the read-write Community string is unknown, an alternative Community
key can be used. The alternative Community key is unique per ODU and can
be used only to change the Community strings. The alternative Community
key is supplied with the product, and should be kept in a safe place.
If both the read-write Community and the alternative Community key are
unavailable, then an alternative Community key can be obtained from RADWIN Customer Support using the ODU serial number or MAC address. The
serial number is located on the product label. The serial number and the
MAC address are displayed in the Site Configuration inventory tab.
When you have the alternative Community key, click the Forgot Community button and enter the Alternative Community key (figure 6-13). Then
change the read-write Community string.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-16
Muting the alignment tone
Chapter 6
Figure 6-13: Alternative Community Dialog box
Muting the alignment tone
The ODU alignment tone becomes audible as soon as power is supplied,
and continues until the ODUs are aligned and the link established.
It is possible to mute the tone during regular operation of the link. It must
be enabled when performing the alignment procedure.
 To mute the alignment tone:
1. Choose a site.
2. The Configuration dialog box opens.
3. In the Configuration dialog box, click the Buzzer button. The button toggles between on and off.
The tone is disabled.
 To restore the alignment tone:
1. Choose a site.
The Configuration dialog box opens.
2. In the Configuration dialog box, click the Buzzer button. The button toggles from on to off. The tone is enabled.
Setting External Alarm Inputs
The IDU-C has two external alarm inputs and two external alarm outputs in
the form of dry-contact relays. The Alarm interface is located on the front
panel of the IDU-C and is a 25-pin D-type female connector. see IDU-C
Alarm Connector on page B-3, for wiring specifications and pinout. The
user enables or disables each of the alarms and can configure the alarm
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-17
Managing Configuration Files
Chapter 6
description text that appears in the alarm trap. The ODU sends the alarm
within less than a second from actual alarm trigger.
 To set the external alarm inputs:
1. Open the Site Configuration Alarms configuration by clicking Configuration | Advanced.
Figure 6-14: External Alarm Configuration
2. Choose an alarm and set its mode to Enabled or Disabled
3. Enter a description of the alarms in the text field.
4. Click Apply to save.
5. Click OK to exit from the dialog.
Managing Configuration Files
Backup Configuration to a File
RADWIN Manager allows you to backup configuration parameters of the
local and remote units to the managing computer as .ini files. Each site is
backed up in a separate .ini file.
 To save the configuration in a file:
1. Choose a site to back up.
The Configuration dialog box opens.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-18
Restoring a Configuration File
Chapter 6
2. Click Backup.
3. In the Save As dialog box, indicate in which folder and under what name
configuration file is to be saved, and click Save.
Restoring a Configuration File
Configuration files (*.ini) can be uploaded from the managing computer.
Such configuration files can be distributed to other units that use the same
configuration.
 To restore a configuration file:
1. Choose a site to restore (from a previous backup).
The Configuration dialog box opens.
2. Click Restore.
3. From the Open dialog box choose *.ini file to upload and click OK.
Backup files are specific to a site (IDU / ODU pair and Link ID).
Caution
Do not restore a backup configuration file to a site other than that from
which it was originally taken.
Resetting
You may reset the link, preserving the current configuration, or reset to factory defaults.
Resetting the link causes service disconnection.
Caution
To maintain the connection between the managing computer and
the link, first reset Site B.
 To reset the link preserving current configuration:
1. From Maintenance on the main window, reset the remote unit.
2. From Maintenance on the main window, reset the local unit.
 To reset to Factory Defaults
1. Choose either of the sites.
The Configuration dialog box opens.
2. Choose Operations in the Configuration dialog box.
3. Click the Restore Defaults button.
A message box asking if you want to restore factory default appears.
4. Click the check box if you want to keep the current IP address settings.
5. Click Yes to continue.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-19
Configuration with Telnet
Chapter 6
Configuration with Telnet
A Telnet terminal can be used to configure and monitor the RADWIN 1000/
2000/5000.
To start a Telnet session, use telnet .
For example, if you run Telnet as follows,
telnet 10.0.0.120
you will be asked for a user name and password.
The login user name/password is identical to the Community strings; Read
allows display only, Read/Write allows display and set commands.
Supported Telnet commands are shown in table 6-2. Note that some of the
commands are model-specific. For example, TDM commands will not apply
to Ethernet only and PoE based links.
Table 6-2: Telnet Commands
Command
Explanation
display inventory
Displays ODU product name, Name, Location, hardware
and software revisions, uptime, MAC address, IDU product
name, IDU software and hardware revisions
display management
Displays IP, Subnet, Gateway, Traps table
display link
Displays State, Link ID, Channel BW, RSS, TSL,
Frequency/ACS, DFS, Rate/ARA, Distance
display Ethernet
Displays Bridge Mode, Aging time, Port table (State, Status
and action)
display tdm
Displays Clock Mode, Master Clock Mode, Current Clock,
Quality[1], TDM table (Line status, Error Blocks)
display ntp
Displays Time, Server and Offset
set ip  

Set the ODU IP address, subnet mask and gateway
The user must reset the ODU after the command
completion
display PM


Shows the performance monitor tables for each interface
according to user defined monitoring intervals
set trap  

Set a specific trap from the traps table (set trap 3
10.0.0.133 162)
set readpw  
Set the read access password (Read Community)
set writepw  
Set the read-write access password (Read-Write
Community)
set trappw  
Set the trap Community string
set buzzer 
Toggle the buzzer mode (0 – off, 1 – on)
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-20
Configuration with Telnet
Chapter 6
Table 6-2: Telnet Commands (Continued)
Command
Explanation
set tpc
Set the ODU transmit power. If a wrong value is entered,
both min and max values shall be displayed in the error
reply
set bridge 
Set the ODU bridge mode (0 – off, 1 – on)
set name 
Set the name of the link
set location 
Set the name of the location
Set contact 
Set the name of the site manager
set Ethernet <>port:MNG,LAN1,LAN2>

Set the mode and speed of each ethernet port
Reboot
Reset both the IDU and the ODU. The user shall be
prompt that the command will reset the card and that he
has to reconnect the telnet session after TBD seconds.
Help
Displays the available commands
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-21
Configuration with Telnet
Chapter 6
figure 6-15, below, shows the available Telnet commands via the Help
command.
Hello admin, welcome to ODU Management CLI!
+-----------------------------------------------------------+
Software Revision
2.1.00_b2070_Jun 5 2008
+-----------------------------------------------------------+
admin@10.0.0.120-> Type "help" for help.
admin@10.0.0.120-> help
display inventory
display management
display link
display ethernet
display tdm
display ntp
display PM 

set ip   
set trap   
set readpw  
set writepw  
set trappw  
set buzzer 
set tpc 
set bridge 
set name 
set location 
set contact 
set ethernet  
reboot
help
Command "help" finished OK.
Figure 6-15: Telnet Management Screen
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
6-22
Chapter 7
Monitoring and
Diagnostics
The RADWIN Manager application enables you to monitor the link, as well
as perform diagnostic operations such as loopback tests.
This chapter covers:
•
Retrieving link information
•
Link compatibility issues
•
Reinstalling and realigning a link
•
Performance monitoring
•
Troubleshooting
•
Replacing an ODU
•
Restoring to factory setup
Retrieving Link Information (Get Diagnostics)
The Get Diagnostics feature collects and writes all link and Manager information (from both sites) into a text file. The file information can be used for
diagnostics and should be sent to RADWIN Customer Support to speed up
assistance.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-1
Retrieving Link Information (Get Diagnostics)
Chapter 7
The following table lists link and system information that can be monitored.
Table 7-1: Get Diagnostics Data and Description
Data
Description
System Data
General information about the system
Link Information
Information about the link properties
Events Log
List of recent system events
Site Configuration
Data about the site parameters
Active Alarms
List of active alarms
Performance Monitor
Network performance data over defined time periods
Monitor
Detailed event data record
 To get diagnostics
1. On the Help menu, choose Get Diagnostic Information.
Figure 7-1: Get Diagnostics Dialog Box
2. Select or deselect the data options. If the file is to be sent to RADWIN
Customer Support leave all options checked.
3. Click File Path to specify the folder in which you want to save the file
and then click Start to save the information.
The file is saved in the specified folder as Diagnostics Information.txt
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-2
Link Compatibility
Chapter 7
Link Compatibility
Link Compatibility indicates the version compatibility using software traps.
As new hardware or software is added to existing networks compatibility
issues may arise. An incompatibility issue is indicated to the user by a
change of color of the Link Status box on the Main Menu screen. Trap messages in the events Log indicate the problems or limitations and suggest
upgrades when appropriate.
The following Link Status messages are given:
fullCompatibility - different software versions were detected that are fully
compatible. The message indicates that an upgrade is available.
restrictedCompatibility - different software versions were detected that
operate correctly. However, new features are not supported
softwareUpgradeRequired - different software versions were detected allowing limited operation. The message is, that a software upgrade required.
versionsIncompatibility - different software versions were detected that are
incompatible. You need to perform local upgrades.
Table 7-2: Link Compatibility Trap Messages
Link State
Link State
text
Link
Status
Color
Site
Desc.
Color
Link Status
fullCompatibility
Active
Green
SW Upgrade
Available
Yellow
Green
restrictedCompatibility
Active - SW
Version mismatch
Magenta
(Same as
authentication
error)
SW Upgrade
Recommended
Yellow
Magenta
(Same as
authentication
error)
softwareUpgradeRequired
Active – SW
Upgrade
Required
Brown
(Major)
SW Upgrade
Required
Yellow
Brown (Major)
versionsIncompatibility
Not Active SW
Upgrade
Required
Red
Local SW
Upgrade
Required
Yellow
Red
Site
Description
Color
Reinstalling and Realigning a Link
It may be necessary to reinstall the link if the ODUs need to be realigned.
Activating Install Mode causes both sites to go into install mode, causing
disruption in service for approximately fifteen seconds.
Note
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-3
The Link Budget Calculator
Chapter 7
 To reinstall the link:
1. Choose a site.
The Configuration dialog box opens.
2. In the Configuration dialog box, click the Install Mode button.
A message box asking if you want to enter install mode appears.
3. Click Yes to continue.
The system enters Install mode and the alignment tone becomes audible.
4. Realign the ODUs and start the Installation wizard (see chapter 4).
The Link Budget Calculator
The Link Budget Calculator is part of the RADWIN Manager software and is
found in the Help menu. This useful utility enables you to calculate the
expected performance of the wireless link and the possible configurations
for a specific link range including antenna size, cable loss and climate conditions. For full details, see appendix D.
Performance Monitoring
RADWIN 1000/2000/5000 Performance Monitoring constantly monitors traffic over the radio link and collects statistics data for the air interface and
Ethernet ports. It does so continuously, even when the RADWIN Manager is
not connected.
Two types of logs are recorded:
•
Monitor Log that records statistics on traffic rate and radio signal
strength.
•
Events Log that records when the rates fall above or below a predefined threshold.
Both the statistics Monitor log and events log can be saved as TXT files.
The Monitor Log
The Monitor Log records performance statistics for predefined intervals. You
can save the monitor log to a text file, as well as display the information in
an on-screen report.
Saving the Monitor Log
You can save the recorded Monitor Log statistics to a text file.
 To save the monitor log:
1. From the Tools menu, choose Preferences.
The Preferences dialog box appears:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-4
The Monitor Log
Chapter 7
Figure 7-2: Preferences dialog box
2. Click the Monitor Tab.
3. Select the file to save.
4. Click the check box to open the file for saving.
5. Click the
button and in the Select File dialog box indicate in which
folder and under what name the monitor log file is to be saved.
6. Set the time interval for adding data to the file.
7. Click OK to save the file.
Viewing Performance Reports
The Performance Monitor Report displays performance views of each of the
interfaces1.
 To obtain performance monitoring reports:
1. From the main menu, choose Tools | Performance Monitoring
Report ...
You are presented with the following window:
1. Ethernet performance is not collected from PoE devices.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-5
The Monitor Log
Chapter 7
Figure 7-3: Basic Performance Monitoring Report
2. Choose a report type from the left panel and click the Get Data toolbar
button. For example, if you choose Site A, Air and Current, you will be
offered a report looking like this:
Figure 7-4: A typical Performance Monitoring Report
You can click the Selection Pane icon to toggle the side panel on or off.
The other reports look similar. Here is a detailed description of the reports
and their fields:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-6
The Monitor Log
Chapter 7
Several performance data occurrences are collected for each of the interfaces (ES, SES, and UAS), as well as Specific data per Interface type (e.g.,
TX and RX bytes for Ethernet). For the Air Interface, user defined thresholds
data are collected. Refer to table 7-3 and table 7-4, in Performance
Monitoring Report Toolbar below.
Data is collected and selectively displayed based on three time intervals as
selected by the Interval radio buttons:
•
Current (t=0)
•
15 minutes Intervals
•
Daily
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-7
The Monitor Log
Chapter 7
Table 7-3: Explanation of performance data
Data type
Generic PM Data
Air Interface PM
Data
Ethernet Interface
PM Data
Reported Value
Explanation
UAS – Unavailable
Seconds
Seconds in which the interface was out of service.
ES – Errored Seconds
The number of seconds in which there was at least
one error block. Note that the notation of an error
block is different per interface.
SES – Severe Errored
Seconds
The number of seconds in which the service quality
was low (the quality is different per type of interface and determined by the BBER threshold per
interface).
BBE – Background
Block Error
The number of errored blocks in an interval.
Integrity
A flag indicating that the data was valid. Note that
the Performance Monitoring data is not valid if not
all the values were stored (e.g., due to clock
changes within the interval or power up reset).
Max RSL
The maximum of the receive signal level (measured in dBm).
Min RSL
The minimum of the receive signal level (measured
in dBm).
Max TSL
The maximum of the transmit signal level (measured in dBm).
Min TSL
The minimum of the transmit signal level (measured in dBm).
RSL Threshold 1
The number of seconds in which the RSL was
below the specified threshold.
RSL Threshold 2
The number of seconds in which the RSL was
below the specified threshold.
TSL Threshold
The number of seconds in which the RSL was
above the specified threshold.
BBER Threshold
The BBER Threshold value counts the number of
seconds in which the Background Block Error Ratio
(BBER) exceeded the specified threshold.
Received Bytes
The number of Megabytes received at the specified
port within the interval
Transmitted Bytes
The number of Megabytes transmitted at the specified port within the interval.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-8
The Monitor Log
Chapter 7
Performance Monitoring Report Toolbar
You can use the toolbar to perform the actions described in the following
table:
Table 7-4: Action of the toolbar buttons
Command Button
Action
Get Data
Gathers current performance monitoring data.
Save
Save current performance monitoring data to a file
Clear
Clear current performance monitoring data.
Thresholds
Set Air Interface Thresholds
Close
Closes the active alarm window.
Setting Air Interface Thresholds
Use the Thresholds button on the Monitoring Performance Report toolbar to
set the Air Interface Thresholds:
Figure 7-5: Threshold configuration dialog box
BBER Threshold
This parameter counts the seconds during which the radio performance is
below a user specified threshold. The threshold is measured as a percentage. The threshold can be set from 0.1% up to 50%.
For links with Ethernet only service, 8% threshold is recommended. If there
are no problems during the interval, then for that threshold, the recommended BBER value should be 0. Since the system provides a lossless
Ethernet service, there is throughput degradation in case of interference.
The degradation is proportional to the BBER.
RSL Threshold
RSL Threshold can also be used as an indicator of problems in the radio
channel. You can check the RSS by from the Link Budget Calculator results
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-9
The Events Log
Chapter 7
during installation. A value of -5dB from the current RSS is recommended as
a threshold.
The Events Log
The Events Log records system failures, loss of synchronization, loss of signal, compatibility problems and other fault conditions and events.
Alarms (traps) are displayed in the Events Log in the lower panel of the
main window. The Events Log may be saved as a text file.
The Events Log includes the following fields:
 Sequential number (ID)
 Date and time stamp
 Message
 Trap source
 IP address of the ODU that initiated alarm.
For complete information about traps and alarms see appendix G, MIB
Reference, table G-3.
The events are displayed in the Events Log in the lower part of the RADWIN
Manager main window:
Figure 7-6: Events Log Display
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-10
RADWIN Manager Traps
Chapter 7
RADWIN Manager Traps
The RADWIN Manager application issues traps to indicate various events,
displayed in the Wvents Log.
Table 7-5: RADWIN Manager Trap Messages
Trap Message
Severity
Remarks
Error loading trap catcher. Port 162 is already in use.
Warning
NMS will not catch any
traps from target, some
other application has
grabbed this port
Device unreachable!
Error
Check connectivity to target
Connected to 
Information
 Site will be reset.
Information
Restore Factory Default Settings in process on Site

Information
Factory Settings: The process was not finished due to
connection issues.
Warning
Factory setting failed due to
connectivity problem to target
Reset: The process was not finished due to connection issues.
Warning
Factory setting failed due to
connectivity problem to target - Target will not be reset
Cannot Write to Monitor file. There is not enough
space on the disk.
Warning
Free some space on disk
and retry
Windows Error: . Cannot Write to Monitor
file.
Warning
Operating System error
TDM Counters were cleared for both sides
Information
Identical IP addresses at  and

Warning
Set up a different IP to each
site
The Product is not identified at the
 site.
Warning
NMS is incompatible with
the target release
The Product is not identified at the
 site.
Warning
The Product is not identified at both sites.
Warning
Product Not Identified!
Warning
The Manager identified a newer ODU release at the
 site.
Warning
The Manager identified a newer ODU release at both
sites.
Warning
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
ODU release is newer than
NMS release. Wizards are
not available. NMS will be
used just for monitoring.
Upgrade the NMS. (You will
get this message as a pop
up)
7-11
RADWIN Manager Traps
Chapter 7
Table 7-5: RADWIN Manager Trap Messages
Trap Message
Severity
The Manager identified a newer ODU release at the
 site.
Warning
Newer Version identified at the 
site.
Warning
Newer Version identified at the 
site.
Warning
Newer Version Identified!
Warning
Remarks
ODU release is newer than
NMS release. Wizards are
not available. NMS will be
used just for monitoring.
Upgrade the NMS
Setting the Events Preferences
You can define a color for the traps to be displayed in the Event Log window, according to the severity of the event. The severity is predefined.
 To set the trap color:
1. From the Tools menu, choose Preferences.
The Preferences dialog box appears.
2. Click the Events Tab:
Figure 7-7: Preferences dialog box
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-12
RADWIN Manager Traps
3. Select the event type and click on the
Chapter 7
button.
A color chart opens.
4. Select the desired color.
5. Repeat for all of the event types.
 To set the trap background color:
• Click Background Color to change the text background.
 To reset the event colors:
• Click Reset Settings to return to the default color settings.
Saving the Events Log
You can save recorded events in an Events Log text file. New alarms are
automatically added to the text file, as they enter the Events Log.
 To save the Events Log:
1. From the Tools menu, choose Preferences.
The Preferences dialog box appears
2. Click the Events Tab.
3. Select the file to save.
4. Click the check box to open the file for saving.
Click the
button and in the Select File dialog box indicate in which folder
and under what name the Events Log file is to be saved, and click OK.
Note
To store the Events Log, first define the IP address, subnet mask, default
gateway and trap address of the managing computer (see Configuring
the ODU Address on page 6-4 for details).
Reverting Alarm Messages
Alarm messages can be reverted to their default values by choosing the
Advanced tab from the Preferences dialog:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-13
RADWIN Manager Traps
Chapter 7
Just click the Restore Defaults button, followed by OK.
Active Alarms
Upon setting a trap destination, applicable events are reported as active
alarms to the user. The active alarms are saved and can be viewed in the
Active Alarms window.
 To view summary of saved alarms:
• From the Tools menu, choose Active Alarm Summary.
The Active Alarms Summary window opens:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-14
RADWIN Manager Traps
Chapter 7
Figure 7-8: Active Alarms Summary
The following table provides an explanation of the command buttons
Table 7-6: Active Alarms command buttons
Command
Action
Save
Saves the alarms in CSV or text format for further analysis.
Refresh
Reads the alarms from the ODU.
Site
Selects site for the active alarms.
Close
Closes the active alarm window.
Remote Power Fail Indication
Remote power fail indication indicates to one side that the other side has
had a power failure. The failed site sends a final trap indication about the
power loss just before powering off.
A “Dying-Gasp” circuit identifies the power failure at a minimum interval of
20 milliseconds before the ODU or IDU powers off. During that interval a
message notifying the power failure is sent to Site B. Alarm output number
4 indicates power failure at Site B.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-15
Troubleshooting
Chapter 7
Troubleshooting
Use the following table to troubleshoot LED fault indications:
Table 7-7: LED fault indicators
LED
Status
Remedy
PWR
Off
Check that AC adapter is connected to the IDU-E and the AC
power outlet.
IDU
Orange
Check that the IDU/ODU cable is properly wired and connected.
ODU
Red
Check that the IDU/ODU cable is properly wired and connected.
AIR I/F
Orange
Complete the installation procedure from the management software.
Red
Check the ODU Antenna alignment. Check that the radio configuration of both site A and site B units are the same (channel and
Link ID).
SVC
Off
Use the following table to troubleshoot faults in the system:.
Table 7-8: Troubleshooting
Symptom
Remedy
No power
Ensure that power is connected to the IDU.
Ensure that the ODU cable is properly wired and connected.
No signal
Complete the installation procedure from the RADWIN Manager
Check the ODU alignment. Check that the radio configuration of both site A
and site B units are the same (channel and Link ID.
Weak signal
received
Check the ODU alignment, reconfigure the link.
Check the alignment tone sounds the Best Signal sequence.
Replacing an ODU
Prior to any action ensure that both ODUs have the same software version.
You can see this on the inventory panels for each site.
For Site A, click Site A | Inventory and note the ODU software version.
Repeat this for Site B using Site B | Inventory.
If either ODU has an old software version, perform a software upgrade. It is
important to configure the new ODU exactly the same as the old ODU to
avoid configuration mismatches, which will disrupt the link.
An ODU may be reconfigured in several ways.
•
Use the backup Configuration
If a backup of the configuration is available, restore that configuration using Site A| Restore.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-16
Restoring Factory Setup
•
Chapter 7
Manual Configuration
The new ODU can be configured manually according to the link configuration. Remember to use the same settings for Link ID, channels, link password, IP addresses, and names.
Restoring Factory Setup
 To restore factory setup:
1. Set the remaining ODUs back to the factory setup by using the Site A
|Advanced option.
2. Activate the second ODU and carry out a new Installation.
Online Help
Online help can be accessed from the Help menu on the main screen of the
RADWIN 1000/2000/5000 Manager.
Figure 7-9: Online Help for RADWIN 1000/2000/5000
Customer Support
Customer support for this product can be obtained from the local VAR, Integrator or distributor from whom it was purchased.
For further information, please contact the RADWIN 1000/2000/5000 distributor nearest to you or one of RADWIN's offices worldwide (see RADWIN Worldwide Offices at the beginning of this manual).
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
7-17
Appendix A
Technical Specifications
Configuration
Architecture
IDU to ODU Interface
ODU: Outdoor Unit with Integrated Antenna or Connectorized for External Antenna
IDU: Indoor Unit for service interfaces or PoE device for
Ethernet only
Outdoor CAT-5e cable; Maximum cable length: 100 m
Radio
Capacity
Range
Channel Bandwidth
Up to 270Mbps at 40MHz channel bandwidth in the 5.3/5.4
IC and 5.8 GHz spectrum bands
Up to 130Mbps at 20MHz channel bandwidth in the 3.5/3.6
GHz spectrum bands
Up to 120 km / 75 miles
5, 10, and 20 MHz
40 MHz in the 5.3/5.4 IC and 5.8 GHz spectrum bands
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
A-1
Radio
Appendix A
Frequency Bands
Band
Regulations
5.725 – 5.850 GHz
FCC / IC
5.725 – 5.825 GHz
FCC(UNII)/IC
5.250 – 5.350 GHz (excluding 40 MHz channel bandwidth and 6dBi antenna
assembly gain)
FCC
5.250 – 5.350 GHz (including
40 MHz channel bandwidth
and 6dBi antenna assembly
gain)
IC
5.470 – 5.725 GHz (excluding 40 MHz channel bandwidth and 6dBi antenna
assembly gain)
FCC
5.470 – 5.725 GHz (including
40 MHz channel bandwidth
and 6dBi antenna assembly
gain)
IC
4.940 – 4.990 GHz
2.400 – 2.4835 GHz
FCC
3.650 – 3.700 GHz
3.475 – 3.650 GHz
Band
5.725 – 5.850 GHz
IC
Max Tx Power
Antenna
29.95 dBm
28 dBi Dish
29.95 dBm
24 dBi Integral Flat
29.95 dBm
23 dBi External Flat
23 dBm
14 dBi External Flat
20 dBm
16.5 dBi External Flat
28 dBm
8 dBi assembly
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
A-2
Radio
Appendix A
Band
5.250 – 5.350 GHz
5.470 – 5.725 GHz
5.725 – 5.825 GHz
Max Tx Power
Antenna
1.9 dBm
28 dBi Dish
6.5 dBm
23.5 dBi Integral Flat
7.5 dBm
22.5 dBi External Flat
23.5dBm
6 dBi assembly
7.4 dBm
14 dBi External Flat
7.4 dBm
15.5 dBi External Flat
23.5 dBm
6 dBi assembly
1.6 dBm
28 dBi Dish
6.3 dBm
23.5 dBi Integral Flat
7.3 dBm
22.5 dBi External Flat
23.7 dBm
6 dBi assembly
7.2 dBm
14 dBi External Flat
7.2 dBm
16.5 dBi External Flat
23.7 dBm
6 dBi assembly
23.8 dBm
28 dBi Dish
26.4 dBm
22.5 dBi Integral Flat
26.4 dBm
23.5 dBi External Flat
29.4 dBm
6 dBi assembly
24.4 dBm
14 dBi External Flat
24 dBm
16.5 dBi External Flat
29.3 dBm
6 dBi assembly
21 dBi Integral Flat
21 dBi External Flat
4.940 – 4.990 GHz
31 dBm
28 dBi Dish
14 dBi External Flat
15 dBi External Flat
2.400 – 2.4835 GHz
25.5 dBm(*)
20 dBi External Flat
25.5 dBm(*)
17.5 dBi Integral Flat
23.7 dBm
20 dBi External Flat
23.7 dBm
17.5 dBi Integral Flat
21 dBi Integral Flat
3.475 – 3.650 GHz
26 dBm
22 dBi External Flat
24 dBi Dish
13 dBi External Flat
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
A-3
Radio
Appendix A
Band
Max Tx Power
Antenna
13.5 dBi assembly
26 dBm
3.650 – 3.700 GHz
13 dBi External Flat
21 dBi Integral Flat
20 dBm
22 dBi External Flat
17 dBm
24 dBi Dish
24 dBm
17 dBi assembly
(*) Relevant for RADWIN 1000 RW-1020-0150 / RADWIN 2000 RW-20200150 models only
Channel Bandwidth
5, 10, and 20 MHz, (10MHz not supported in the 5.8 GHz
band)
Radio Modulation
2x2 MIMO-OFDM (BPSK/QPSK/16QAM/64QAM)
Adaptive Modulation &
Coding
Supported
Automatic Channel Selection
Supported
Radio Regulation
FCC 47 CFR Part 15 Subpart C, E, Part 90 Subpart Y, Z
IC (Canada) RSS-210, RSS-111, RSS-192, RSS-197
Duplex Technology
TDD
Error Correction
FEC k = 1/2, 2/3, 3/4, 5/6
Encryption
AES 128
Rate – Single Antenna
[Mbps]
6.5
13
19.5
26
39
52
58.5
65
Rate – Single Antenna in the
5.8 GHz spectrum band
[Mbps]
13.5
27
40.5
54
81
108
121.5
135
Rate – Dual Antenna [Mbps]
13
26
39
52
78
104
117
130
Rate –Dual Antenna in the
5.8 GHz spectrum band
[Mbps]
27
54
81
108
162
216
243
270
Modulation
FEC [k=]
BPSK
1/2
Max Tx Power [dBm]
Sensitivity (dBm) @BER
<10e-11 (20MHz)
QPSK
1/2
3/4
25
-88
-86
-83
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
16QAM
64QAM
1/2
3/4
2/3
24
21
19
-81
-80
-72
3/4
5/6
18
-70
-67
A-4
Ethernet Interface
Appendix A
Ethernet Interface
Throughput
Up to 270Mbps in the 5.3/5.4 IC and 5.8 GHz spectrum
bands
Number of Ethernet ports
IDU-C and E: 2; PoE Device: 1
Type
10/100BaseT with Auto-Negotiation (IEEE 802.3u)
Framing/Coding
IEEE 802.3
Line Impedance
100 Ω
VLAN Support
Transparent
Connector
RJ-45
Maximum Frame Size
2048 Bytes
Bridge
Layer 2, self-learning of up to 2047 MAC addresses (IEEE
802.1Q), hub/Bridge selectable mode
Latency
3 msec (typical)
Management
Management Application
RADWIN Manager
Protocol
SNMP and Telnet
Mechanical
ODU with Integrated Antenna: 37.1/14.84(W) x 37.1/
14.84(H) x 9.00/3.6(D) cm/in; 3.5 kg / 7 lbs
Dimensions
ODU Connectorized: 18.0/7.2(W) x 27.0/10.8(H) x 5.5/
2.2(D) cm/in; 1.5 kg / 3.0 lbs
IDU-C: 43.6/17.2(W) x 4.5/1.7(H) x 21/8.3(D) cm; 1.5 kg /
3.3 lbs
IDU-E: 22/8.7(W) x 4.4/1.7(H) x 17/6.7(D) cm/in; 0.5 Kg /
1.1 lbs
Power
Power Feeding
Dual feeding, -20 to -60 VDC (AC/DC converter is available)
Power Consumption
< 35 W (IDU+ODU)
Environmental
ODU: -35°C to +60°C / -31°F to +140°F
Operating Temperatures
Humidity
IDU-C: 0°C to +50°C / 32°F to +122°F
IDU-E: -5°C to 45°C / 32°F to 122°F
ODU: Up to 100% non-condensing, IP67
IDU: 90% non-condensing
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
A-5
Safety
Appendix A
Safety
FCC/IC (cTUVus)
UL 60950-1, CAN/CSA 60950-1 C22.2
ETSI
EN/IEC 60950-1
EMC
FCC
CFR47 Class B, Part15, Subpart B
ETSI
EN 300 386 (2005), EN 301 489-1 (2001), EN 301 489-4
(2002)
CAN/CSA-CEI/IEC
CISPR 22-02
AS/NZS
CISPR 22:2002
Air Interface
RADWIN 1000/2000/5000 is available in several different frequency band
ranges that comply with ETSI, FCC and IC regulations.
The RADWIN 1000 RW-1020-0150 / RADWIN 2000 RW-2020-0150 is available only in the 2.4GHz frequency band range that complies with FCC and
IC regulations.
The RADWIN 1000 3GHz Band / RADWIN 2000 3GHz Band / RADWIN 5000
3GHz Band support the 3.5 / 3.6 GHz frequency bands and comply with FCC
and IC regulations.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
A-6
Appendix B
Wiring Specifications
ODU-IDU Cable
The ODU-IDU cable is shielded/outdoor class CAT-5e, 4 twisted-pair 24
AWG terminated with RJ-45 connectors on both ends. A cable gland on the
ODU side provides hermetic sealing.
The following table shows the connector pinout:
Table B-1: ODU-IDU Connector Pinout
Function
Color
IDU RJ-45
ODU
RJ-45
Ethernet (RxN)
White/Green
twisted
Ethernet (RxT)
Green
pair
Ethernet (TxT)
White/Orange
twisted
pair
twisted
pair
twisted
pair
Ethernet (TxN)
Orange
Power (+)
Blue
Power (+)
White/Blue
Power ()
White/Brown
Power ()
Brown
User Port Connectors
LAN Port
The LAN 10/100BaseT interface terminates in an 8-pin RJ-45 connector,
wired in accordance to table B-2.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
B-1
LAN Port
Appendix B
Table B-2: Fast Ethernet Connector Pinout
Pin
Signal
Function
TD (+)
Transmit Data
(positive)
TD (–)
Transmit Data
(negative)
RD (+)
Receive Data
(positive)
RD (–)
Receive Data
(negative)
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
B-2
IDU-C Alarm Connector
Appendix B
IDU-C Alarm Connector
The IDU-C Alarm interface is a 25 pin D type female connector. Its pinout is
listed in table B-3.
Table B-3: IDU-C Alarm Connector (Dry-Contact)
I/O
Description
Pin
Input 1
Positive
14
Input 1
Negative
15
Input 2
Positive
16
Input 2
Negative
17
Input 3
Positive
18
Input 3
Negative
19
Input 4
Positive
20
Input 4
Negative
21
Output 1
Normally Open
Output 1
Common
Output 1
Normally
Closed
Output 2
Normally Open
Output 2
Common
Output 2
Normally
Closed
Output 3
Normally Open
Output 3
Common
Output 3
Normally
Closed
Output 4
Normally Open
10
Output 4
Common
11
Output 4
Normally
Closed
12
The following diagram describes how to connect external input and output
alarms.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
B-3
IDU-C Alarm Connector
Note
Appendix B
•
Use an external current limit resistor to limit the current at the output
relays to 1 Ampere. Such resistor is not required if the equipment
connected to the IDU supports current limiting to 1 Amp.
•
The voltage of the input alarm must be within the range of -10 to -50
VDC.
Figure B-1: Example for connecting the alarm connector
DC Power Terminal
Table B-4: Terminal Block 3-pin -48VDC
Function
Pin
Right
Chassis
Center
–
Left
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
B-4
Appendix C
Pole and Wall Installation
ODU Mounting Kit Contents
Table C-1: Bill of Materials: ODU mounting kit
Item
Qty
Large Clamp (see figure C-1)
Small Clamp (see figure C-2)
Arm (see figure C-3)
Screw hex head M8x40
Screw hex head M8x70
Washer flat M8
Washer spring M8
M8 Nuts
Figure C-1: Large Clamp
Figure C-2: Small Clamp
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
Figure C-3: Arm
C-1
Mounting RADWIN 1000/2000/5000 on a pole
Appendix C
Mounting RADWIN 1000/2000/5000 on a pole
Figure C-4: Mounting on a pole
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
C-2
Mounting RADWIN 1000/2000/5000 on a Wall
Appendix C
Mounting RADWIN 1000/2000/5000 on a Wall
Figure C-5: Mounting on a Wall
Mounting an External Antenna
Optional external antennas can be mounted on a pole. The external mounting kit varies according to the specific antenna.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
C-3
Appendix D
Link Budget Calculator
Overview
The Link Budget Calculator is a utility for calculating the expected performance of the RADWIN 1000/2000/5000 wireless link and the possible configurations for a specific link range.
The utility allows you to calculate the expected RSS of the link, and find the
type of services and their effective throughput as a function of the link
range and deployment conditions.
User Input
You are required to enter or choose the following parameters. Depending
on the product, some of the parameters have a default value that cannot be
changed.
•
Product (or Regulation and Band)
•
Channel Bandwidth (fixed to 20 MHz for RADWIN 1000/2000/5000)
•
Tx Power (maximum Tx power per modulation is validated)
•
Antenna Type (cannot be changed for ODU with integrated antenna)
•
Antenna Gain per site (cannot be changed for integrated antenna)
•
Cable Loss per site (cannot be changed for integrated antenna)
•
Required Fade Margin
•
Rate (and Adaptive check box)
•
Service Type (Ethernet Only for RADWIN 1000/2000/5000 version
2.1)
•
Required Range
Link Budget Calculator Internal Data
For each product (or Regulation and Band) the calculator stores the following data required for link budget calculations:
•
Maximum Transmit power (per modulation)
•
Receiver Sensitivity (per modulation) for Ethernet service and for
TDM services at various BER
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-1
Calculations
Appendix D
•
Maximum linear input power (used to calculate minimum distance)
•
Antenna gain and cable loss for ODU with integrated antenna
•
Available Channel Bandwidths
Calculations
EIRP
EIRP = TxPower + AntennaGain SiteA – CableLoss SiteA
Expected RSS and Fade Margin
ExpectedRSS = EIRP – PathLoss + AntennaGain SiteB – CableLoss SiteB
where:
Site A is the transmitting site
Site B is the receiving site
PathLoss is calculated according to the free space model,
PathLoss = 32.45 + 20  log 10 frequency MHz  + 20  log 10 RequiredRange Km 
ExpectedFadeM arg in = Sensitivity – ExpectedRSS
where Sensitivity is dependent on air-rate.
Min and Max Range
MinRange is the shortest range for which
ExpectedRSS  MaxInputPower per air-rate.
MaxRange (with Adaptive checked) is the largest range for which
ExpectedRSS  Sensitivity , at the highest air-rate for which this relationship is true. In a link with adaptive rate this will be the actual behavior.
MaxRange (for a given air-rate) is the largest range for which
ExpectedRSS  Sensitivity + RequiredFadeM arg in .
Service
The Ethernet throughput is calculated according to internal product algorithms.
Availability
The Service Availability calculation is based on the Vigants Barnett method
which predicts the downtime probability based on a climate factor (C factor).
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-2
Antenna Height
Appendix D
Availability = 6  10
 10
–7
 Cfactor  frequency GHz   RequiredRangeKM 
–-----------------------------------------------------------ExpectedFadeM arg in
10
Antenna Height
The recommended antenna height required for line of sight is calculated as
the sum the Fresnel zone height and the boresight height. See About the
Fresnel Zone below.
The Fresnel zone height is calculated as:
300
----------------------------------  ExpectedRange
----------------------------------------frequency GHz
0.6  ------------------------------------------------------------------------------------------ExpectedRange
----------------------------------------- + ExpectedRange
----------------------------------------2
The boresight clearance height is calculated as:
Maean
ExpectedRange
+ ----------------------------------------2
– R Maean
where R Mean = 6367.4425Km .
Running the Link Budget Calculator
The Link Budget Calculator is supplied on the RADWIN Manager CD. It may
be run stand-alone from the CD or from the RADWIN Manager application.
 To run the Link Budget Calculator from the CD:
1. Insert the RADWIN Manager CD into the drive on the managing computer. In the window which opens, click the Link Budget Calculator
option.
2. If the CD autorun application does not start by itself, then point your
browser to
Z:\RADWIN\Setup\DATA\Link Budget Calculator.htm
where Z should be replaced with your own CD drive name.
 To run the Link Budget Calculator from the RADWIN Manager:
• Choose Help | Link Budget Calculator from the main menu of the
RADWIN Manager as in the following figure:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-3
Running the Link Budget Calculator
Appendix D
Figure D-1: Accessing the Link Budget Calculator
However invoked, your browser displays the following page:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-4
Running the Link Budget Calculator
Appendix D
Figure D-2: Link Budget Screen
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-5
Running the Link Budget Calculator
•
Appendix D
Microsoft Internet Explorer users may see a warning message like
this:
Click the yellow bar and follow the instructions to allow blocked
content.
Note
•
Mozilla FireFox and Google Chrome users may see a warning message like this:
You may ignore it and continue.
 To use the Link Budget Calculator for RADWIN 1000/2000/5000:
1. Choose a product from the drop-down list (or choose a Regulation and
Band):
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-6
Running the Link Budget Calculator
Appendix D
Figure D-3: Product selector
2. Enter the radio details. Note that Rate is chosen from a drop-down list:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-7
Running the Link Budget Calculator
Appendix D
Figure D-4: Rate selector
The Rate shown, defines the air-interface rate in Mbps. The system
operates in TDD mode and has the overhead of the air-interface protoco.l Thus, the Ethernet actual throughput is provided by the Ethernet
Rate.
For a given air-rate, Ethernet throughput will decrease with increasing range
due to propagation delay.
Note
The Fade margin is the minimum required for LOS conditions. For
degraded link conditions, a larger Fade margin should be used.
The EIRP is given in dBm and Watts.
3. If the required range between the two link sites is known, you may enter
it directly. Alternatively, you may enter the latitude and longitude of each
site in the link, in which case the distance between them will be calculated and displayed.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-8
Running the Link Budget Calculator
Appendix D
Figure D-5: Calculation of distance from site coordinates
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-9
Running the Link Budget Calculator
Appendix D
4. Located to the right of the green Coordinates button is a dropdown list of
Climactic C Factor values.
Figure D-6: Climactic C Factors
For help about what these mean, click the ? button to the right of the list
in figure D-6.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-10
Running the Link Budget Calculator
Appendix D
Figure D-7: Climactic C Factor description
In figure D-8 we display a map of the world showing C Factor contours:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-11
Running the Link Budget Calculator
Appendix D
Figure D-8: World map showing C Factor contours
5. Click Calculate to obtain the required performance estimate.
Placing the cursor in any other calculated field will also update the
calculated results.
Note
The Expected Performance parameters are calculated and displayed:
•
Expected RSS - the expected RSS that the RADWIN Manager
shows when the RADWIN 1000/2000/5000 ODUs are optimally
aligned
•
Ethernet Rate - maximum throughput available for the chosen
parameter combination
•
Antenna height for LOS – the minimum antenna height required
for line-of-sight operation. It is the sum of the height required for
boresight clearance due to the earth’s curvature plus the height
required to clear the Fresnel zone
If the expected performance is not suitable for your application, try different
parameters and repeat the calculation.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-12
About the Fresnel Zone
Appendix D
About the Fresnel Zone
The Fresnel zone (pronounced "frA-nel", with a silent “s”) is an elliptically
shaped conical zone of electromagnetic energy that propagates from the
transmitting antenna to the receiving antenna. It is always widest in the
middle of the path between the two antennas.
Figure D-9: Fresnel zone
Fresnel loss is the path loss occurring from multi-path reflections from
reflective surfaces such as water, and intervening obstacles such as buildings or mountain peaks within the Fresnel zone.
Radio links should be designed to accommodate obstructions and atmospheric conditions, weather conditions, large bodies of water, and other
reflectors and absorbers of electromagnetic energy.
The Fresnel zone provides us with a way to calculate the amount of clearance that a wireless wave needs from an obstacle to ensure that the obstacle does not attenuate the signal.
There are infinitely many Fresnel zones located coaxially around the center
of the direct wave. The outer boundary of the first Fresnel zone is defined
as the combined path length of all paths, which are half wavelength (1/2 )
of the frequency transmitted longer than the direct path. If the total path
distance is one wavelength (1 ) longer than the direct path, then the outer
boundary is said to be two Fresnel zones. Odd number Fresnel zones reinforce the direct wave path signal; even number Fresnel zones cancel the
direct wave path signal.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-13
About the Fresnel Zone
Appendix D
The amount of the Fresnel zone clearance is determined by the wavelength
of the signal, the path length, and the distance to the obstacle. For reliability, point-to-point links are designed to have at least 60% of the first Fresnel
zone clear to avoid significant attenuation.
The concept of the Fresnel zone is shown in figure D-9 above. The top of
the obstruction does not extend far into the Fresnel zone, leaving 60% of
the Fresnel zone clear; therefore, the signal is not significantly attenuated.
For more about Fresnel zone, see http://en.wikipedia.org/wiki/
Fresnel_zone.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
D-14
Appendix E
Lightning Protection and
Grounding Guidelines
Meticulous implementation of the guidelines in this appendix will provide
best protection against electric shock and lightning.
100% protection is neither implied nor possible.
Warning
This appendix is at best a guide. The actual degree of lightning protection
required depends on local conditions and regulations.
Note
The RADWIN 1000/2000/5000™ Lightning protection system consists of the
following components:
•
Grounding for the antenna coax cable
•
Grounding for each IDU and ODU
•
External Primary Surge Suppressor units and grounding for the outdoor cable
•
Internal ESD protection circuits over the Power/Telecom lines
Grounding for Antenna Cable
A Grounding Kit must be connected to the coax antenna cable and reliably
grounded as shown in Figure X. The grounding kit is an Andrew Type
223158-2 (www.andrew.com). See figure E-1 below.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
E-1
Grounding for Indoor/Outdoor Units
Appendix E
Figure E-1: Grounding antenna cables
Grounding for Indoor/Outdoor Units
ODU Grounding
RADWIN 1000/2000/5000™ uses a Shielded CAT-5e cable to interconnect
the Outdoor (ODU) and Indoor (IDU) units.
However, this shielding does not provide a good Lightning Discharge path,
since it can not tolerate the high Lightning Current surges.
To provide an alternate Lightning Discharge path, the ODU and antenna
grounding posts should be connected to ground point by a 10 AWG short
copper wire.
The device should be permanently connected to ground.
IDU Grounding
The IDUs grounding post should be connected to the internal ground point,
using a grounding wire of at least 10 AWG. The grounding wire should be
connected to a grounding rod or the building grounding system.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
E-2
External Lightning Surge Suppressors and Grounding
Appendix E
The device should be permanently connected to ground.
External Lightning Surge Suppressors and Grounding
A Grounding Kit and Surge Arrestor Unit must be located near the ODU and
properly grounded as illustrated in figure E-2 and figure E-3 below:
Figure E-2: Grounding a typical pole installation
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
E-3
External Lightning Surge Suppressors and Grounding
Appendix E
Figure E-3: Grounding a typical wall installation
The next figure shows a close-up of the rear of grounded ODU:
Figure E-4: ODU Surge Suppressor and grounding
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
E-4
External Lightning Surge Suppressors and Grounding
Appendix E
The Transtector protection circuits shown in figure E-5 below, utilize silicon
avalanche diode technology. The unit consists of an outdoor rated NEMA 3R
type enclosure with easy mounting flanges, ground stud attachment and
easy wiring.
The ALPU-POE features RJ-45 protection circuits for the ODU-IDU data pairs
(pins 1,2 & 3,6) and DC power (pins 4,5 & 6,7 with the pairs bonded).
The unit is designed to be wall mounted. An optional set of bracket is available to allow a wide range of pole mount applications. A dedicated ground
stud is provided inside the unit that must be bonded to the nearest grounding system (or Master Ground bar) for proper surge protection.
The system wiring is installed with RJ-45 type connectors that can feed
directly into the chassis without having to cut, splice or route through awkward strain relief holes.
Figure E-5: Transtector’s Surge Suppressor
 To mount the lightning protection devices:
1. Mount the device as close to the ODU as possible. Mount the unit so that
the cable connectors are at the bottom (to prevent water from penetrating), with the strain reliefs facing the ground.
2. Remove the cover by unscrewing the front of the unit.
3. Mount the unit to an outside surface using the two mounting holes.
4. Connect the ODU-IDU cable using the RJ-45 jack.
5. Connect one cable between the ODU and the suppressor using an RJ-45
jack.
6. Connect the suppressor’s ground stud to a grounding point. Use the
appropriate wire gauge and type, keeping the wire as short as possible,
less than 1m (3’), between the stud and the site grounding point.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
E-5
External Lightning Surge Suppressors and Grounding
Appendix E
7. Replace the cover.
Note
There may also be regulatory requirements to cross bond the ODU-IDU CAT5e cable at regular intervals up the mast. This may be as frequent as every
10 meters (33 feet).
A second Surge Arrestor Unit should be mounted at the building entry point
and must be grounded, as shown in figure E-3 above.
 To mount the lightning protection at the building entry point:
1. Mount the device outside the building, located as near as possible to the
entrance of the CAT-5e ODU-IDU cable. Mount the unit so that the cable
connectors are at the bottom (to prevent water from penetrating), with
the strain reliefs facing the ground.
2. Remove the cover by unscrewing the front of the unit.
3. Mount the unit to an outside surface using the two mounting holes.
4. Connect the ODU-IDU cable using the RJ-45 jack.
5. Connect one cable between the IDU and the suppressor using an RJ-45
jack.
6. Connect the suppressor’s ground stud to a grounding point. Use the
appropriate wire gauge and type, keeping the wire as short as possible,
less than 1m (3’), between the stud and the site grounding point.
7. Replace the cover
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
E-6
Internal ESD Protection circuits
Appendix E
Figure E-6: Surge Suppressor and grounding at building entry point
Internal ESD Protection circuits
RADWIN 1000/2000/5000™ is designed to meet the ETSI/FCC/Aus/NZ/CSA
EMC and Safety requirements. To fulfill these requirements, the system's
Telecom lines at the ODU/IDU are Transformer-isolated and include internal
ESD (Electro-Static-Discharge) Protection circuits.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
E-7
Appendix F
FCC/IC DFS Installation
Procedure
FCC/IC 5.4/5.3 GHz Links: Background
The FCC/IC regulation for 5.4/5.3 GHz allows unlicensed wireless data
equipment, provided that it does not interrupt radar services. If radar activity is detected, the equipment must automatically change frequency channel. This feature is termed Dynamic Frequency Selection (DFS). According
to the standard, a channel with active radar is prohibited from use for 30
minutes. Before using a channel for transmission, the radio equipment must
probe it for radar signals for a period of 60 seconds.
Note
The FCC/IC regulations for 5.4 GHz band requires the frequency range
5600 – 5650 MHz to be banned from use. The FCC regulation for 5.4 GHz
band requires that within 35 km radius from any (Terminal Doppler
Weather Radars) TDWR location the frequency range 5570 – 5680 MHz
shall be banned from use.
Follow the instructions in the last section of this chapter.
RADWIN radio products support DFS as well as ACS.
An immediate consequence of the FCC/IC regulation for 5.4/5.3 GHz is that
the standard method of link installation using a single default fixed installation channel, cannot be used.
Instead of the installation procedure of Chapter 4, a link activation
method is used. The ODUs do not transmit until they are both configured
and in place. An activation button may be found by navigating to
Site:Location|Air Interface.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-1
FCC/IC 5.4/5.3 GHz Link Activation
Appendix F
The ODUs are either supplied from the factory ready for use at 5.4 GHz or
5.3 GHz FCC/IC or alternatively, they can be set up for these bands using
the RADWIN Manager.
Note
The following procedure is generic to all relevant RADWIN radio products.
What you see on your running RADWIN Manager may differ in some details
from the screen captures used to illustrate this chapter.
FCC/IC 5.4/5.3 GHz Link Activation
 To Activate a FCC/IC 5.4/5.3 GHz Link:
1. Install RADWIN Manager software as usual.
2. Connect the PC to the IDU-ODU pair to be used as the local site.
3. Run the RADWIN Manager and log in as Installer. You will see the following window:
Figure F-1: Activating an ODU - Inactive link
When the Manager Main Screen is displayed it appears with the Link Status label red and showing Inactive.
4. Click Site:Location | Air Interface for the logged in site.
5. The Air Interface dialog box opens:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-2
FCC/IC 5.4/5.3 GHz Link Activation
Appendix F
Figure F-2: Air Interface dialog box
6. Enter the Link ID and note it for use with the second site of the link.
7. Check the Master radio button.
8. Click OK. The following window appears:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-3
FCC/IC 5.4/5.3 GHz Link Activation
Appendix F
Figure F-3: The local ODU after activation - Probing
Notice that the Link ID is shown in the Link details pane (circled).
9. Repeat the above procedure for the remote ODU, ensuring that in the Air
Interface window, that you enter exactly the same Link ID, but this time
that you check the Slave radio button.
If both ODUs are powered up, after a minute or so a link will be established. If you are still connected to the remote site (from the previous
steps), the window of figure F-3 will look like this:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-4
FCC/IC 5.4/5.3 GHz Link Configuration
Appendix F
Figure F-4: Both sites activated and awaiting configuration
FCC/IC 5.4/5.3 GHz Link Configuration
The Configuration procedure may be carried out from either site using the
Configuration wizard as shown in Chapter 5.
Both sites in a FCC/IC 5.4/5.3 GHz Link must be configured
identically.
Note
The only difference is in the Channel Settings window:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-5
FCC/IC 5.4/5.3 GHz Link Configuration
Appendix F
Figure F-5: Channel Select dialog box - ACS permanently enabled
ACS cannot be disabled.
Note
Upon completion of the wizard, the Site configuration dialogs can be used in
the usual way. Once operational, the RADWIN Manager window is the same
as for other radio equipment models.
Here is the RADWIN Manager main window upon completion of the wizard:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-6
FCC 5.4GHz Device Registration
Appendix F
Figure F-6: FCC/IC 5.4/5.3 GHz operational
FCC 5.4GHz Device Registration
The FCC requires that devices installed within 35 km of any TDWR location
should be registered in the voluntary WISPA sponsored database.
The FCC has published a TDWR Location Information table that lists the
exact location of all TDWR towers (see table F-1 at the end of the chapter).
1. When installing a 5.4 GHz device define your exact location (latitude and
longitude)
2. Use the TDWR Location Information table to determine if the distance
between the device and any TDWR tower is less than 35 km.
3. If the distance is less than 35 km then register the device in the
voluntary WISPA sponsored database (following section)
4. Disable the frequencies between 5570 – 5680 MHz from the available
channels list.
5. The frequency range between 5.600 to 5.650 GHz is not included in the
available channels list.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-7
Registering the Device
Appendix F
Registering the Device
 To register a device:
1. Enter the website http://www.spectrumbridge.com/udia/home.aspx and
follow the instructions.
At your first entry into the site, you will be required to register as a user:
2. Click the User Registration button to enter the registration page.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-8
Registering the Device
Appendix F
3. Fill in the registration page and click Register.
4. To complete device registration enter the Register Device tab as shown:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-9
Registering the Device
Appendix F
You are offered this:
5. Fill in the required information in the preceding web page and click the
Register Device button.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-10
TDWR Table
Appendix F
TDWR Table
The following table contains the latitude and longitude locations of Terminal
Doppler Weather Radars (TDWR). Use this table to determine if the Master
or Client device installed is within 35 km radius of a TDWR location. If one
of the installed devices is within 35 km radius of any TDWR location then
disable all frequencies between 5570 – 5680 MHz from the available channels list.
Table F-1: Latitude and longitude locations of TDWRs
STATE
CITY
LONGITUDE
LATITUDE
FREQUENCY
TERRAIN
ELEVATION
(MSL) [ft]
ANTENNA
HEIGHT
ABOVE
TERRAIN
[ft]
AZ
PHOENIX
W 112 09 46
N 33 25 14
5610 MHz
1024
64
CO
DENVER
W 104 31 35
N 39 43 39
5615 MHz
5643
64
FL
FT LAUDERDALE
W 080 20 39
N 26 08 36
5645 MHz
113
FL
MIAMI
W 080 29 28
N 25 45 27
5605 MHz
10
113
FL
ORLANDO
W 081 19 33
N 28 20 37
5640 MHz
72
97
FL
TAMPA
W 082 31 04
N 27 51 35
5620 MHz
14
80
FL
WEST PALM BEACH
W 080 16 23
N 26 41 17
5615 MHz
20
113
GA
ATLANTA
W 084 15 44
N 33 38 48
5615 MHz
962
113
IL
MCCOOK
W 087 51 31
N 41 47 50
5615 MHz
646
97
IL
CRESTWOOD
W 087 43 47
N 41 39 05
5645 MHz
663
113
IN
INDIANAPOLIS
W 086 26 08
N 39 38 14
5605 MHz
751
97
KS
WICHITA
W 097 26 13
N 37 30 26
5603 MHz
1270
80
KY
COVINGTON CINCINNATI
W 084 34 48
N 38 53 53
5610 MHz
942
97
KY
LOUISVILLE
W 085 36 38
N 38 02 45
5646 MHz
617
113
LA
NEW ORLEANS
W 090 24 11
N 30 01 18
5645 MHz
97
MA
BOSTON
W 070 56 01
N 42 09 30
5610 MHz
151
113
MD
BRANDYWINE
W 076 50 42
N 38 41 43
5635 MHz
233
113
MD
BENFIELD
W 076 37 48
N 39 05 23
5645 MHz
184
113
MD
CLINTON
W 076 57 43
N 38 45 32
5615 MHz
249
97
MI
DETROIT
W 083 30 54
N 42 06 40
5615 MHz
656
113
MN
MINNEAPOLIS
W 092 55 58
N 44 52 17
5610 MHz
1040
80
MO
KANSAS CITY
W 094 44 31
N 39 29 55
5605 MHz
1040
64
MO
SAINT LOUIS
W 090 29 21
N 38 48 20
5610 MHz
551
97
MS
DESOTO COUNTY
W 089 59 33
N 34 53 45
5610 MHz
371
113
NC
CHARLOTTE
W 080 53 06
N 35 20 14
5608 MHz
757
113
NC
RALEIGH DURHAM
W 078 41 50
N 36 00 07
5647 MHz
400
113
NJ
WOODBRIDGE
W 074 16 13
N 40 35 37
5620 MHz
19
113
NJ
PENNSAUKEN
W 075 04 12
N 39 56 57
5610 MHz
39
113
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-11
TDWR Table
Appendix F
Table F-1: Latitude and longitude locations of TDWRs (Continued)
STATE
CITY
LONGITUDE
LATITUDE
FREQUENCY
TERRAIN
ELEVATION
(MSL) [ft]
ANTENNA
HEIGHT
ABOVE
TERRAIN
[ft]
NV
LAS VEGAS
W 115 00 26
N 36 08 37
5645 MHz
1995
64
NY
FLOYD BENNETT FIELD
W 073 52 49
N 40 35 20
5647 MHz
97
OH
DAYTON
W 084 07 23
N 40 01 19
5640 MHz
922
97
OH
CLEVELAND
W 082 00 28
N 41 17 23
5645 MHz
817
113
OH
COLUMBUS
W 082 42 55
N 40 00 20
5605 MHz
1037
113
OK
AERO. CTR TDWR #1
W 097 37 31
N 35 24 19
5610 MHz
1285
80
OK
AERO. CTR TDWR #2
W 097 37 43
N 35 23 34
5620 MHz
1293
97
OK
TULSA
W 095 49 34
N 36 04 14
5605 MHz
712
113
OK
OKLAHOMA CITY
W 097 30 36
N 35 16 34
5603 MHz
1195
64
PA
HANOVER
W 080 29 10
N 40 30 05
5615 MHz
1266
113
PR
SAN JUAN
W 066 10 46
N 18 28 26
5610 MHz
59
113
TN
NASHVILLE
W 086 39 42
N 35 58 47
5605 MHz
722
97
TX
HOUSTON INTERCONTL
W 095 34 01
N 30 03 54
5605 MHz
154
97
TX
PEARLAND
W 095 14 30
N 29 30 59
5645 MHz
36
80
TX
DALLAS LOVE FIELD
W 096 58 06
N 32 55 33
5608 MHz
541
80
TX
LEWISVILLE DFW
W 096 55 05
N 33 03 53
5640 MHz
554
31
UT
SALT LAKE CITY
W 111 55 47
N 40 58 02
5610 MHz
4219
80
VA
LEESBURG
W 077 31 46
N 39 05 02
5605 MHz
361
113
WI
MILWAUKEE
W 088 02 47
N 42 49 10
5603 MHz
820
113
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
F-12
Appendix G
MIB Reference
Introduction
About the MIB
The RADWIN MIB is a set of APIs that enables external applications to control RADWIN equipment.
The MIB is divided into public and a private API groups:
•
Public: RFC-1213 (MIB II) variables, RFC-1214 (MIB II) System and
Interfaces sections
•
Private: Controlled by RADWIN and supplements the public group.
This appendix describes the public and private MIB used by RADWIN.
Terminology
The following terms are used in this appendix.
Term
Meaning
MIB
Management Information Base
API
Application Programming Interface
SNMP
Simple Network Management Protocol
In addition, the MIB uses internally, the older notions of Local site and
Remote site where this manual would use site A and site B.
To avoid burdening the reader, this appendix will follow the MIB usage.
Interface API
Control Method
The RADWIN Manager application provides all the means to configure and
monitor a RADWIN 1000/2000/5000 link, communicating with the SNMP
agent in each ODU. Each SNMP agent contains data on each of the IDUs
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
G-1
Community String
Appendix G
and ODUs in the link. Both agents communicate with each other over the air
using a proprietary protocol.
Each ODU has a single MAC address and a single IP address.
Note
To control and configure the device using the MIB, you should adhere to the
following rules:
•
The connection for control and configuration is to the local site, over
any SNMP/UDP/IP network.
•
All Parameters should be consistent between both of the ODUs. Note
that inconsistency of air parameters can break the air connection. To
correct air parameters inconsistency you must reconfigure each of
the ODUs.
•
Common practice is to configure the remote site first and then to
configure the local site.
•
For some of the configuration parameters additional action must be
taken before the new value is loaded. Please refer to the operation
in the parameters description.
•
Some of the MIB parameters values are product dependent. It is
strongly recommend using the RADWIN Manager Application for
changing these values. Setting wrong values may cause indeterminate results.
Community String
To control a link, all SNMP requests should go to the local site IP address.
The RADWIN Manager uses the Read Community strings public for the
local ODU and public-remote for the remote ODU. It uses Write Community strings netman for the local ODU and netman-remote for the
remote ODU. These are the factory defaults.
Private MIB Structure
The sections in the private RADWIN MIB and its location in the MIB tree are
shown in figure G-1 below:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
G-2
Private MIB Structure
Appendix G
Figure G-1: Top Level Sections of the private MIB
The products MIB section contains the definition of the Object IDs for the
two form factors of the ODU, Integrated Antenna and Connectorized
(referred in the MIB as external antenna):
The ODU MIB contains the sections: Admin, Service, Ethernet, Bridge, Air,
PerfMon and Agent.
The IDU MIB contains the sections: Admin, Service, Ethernet, Bridge and
TDM.
The general MIB include a single generic parameter that is used by all traps
as a trap description parameter.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
G-3
MIB Parameters
Appendix G
MIB Parameters
The following section describes all of the MIB parameters. The MIB parameters follow the following naming convention:
...

For each of the configuration and control parameters (parameters with
read-write access), the “Description” column describes when the new value
is effective. It is recommended that you perform the appropriate action to
make the values affective immediately after any change. Where a change is
required on both sides of the link, it is recommended that you change both
sides of the link first and then perform the action.
Supported Variables from the RFC 1213 MIB
Table G-1: Supported RFC 1213 Variables (Sheet 1 of 2)
Access
Name
OID
Type
ifIndex
.1.3.6.1.2.1.2.2.1.1.xa
Integer
RO
A unique value for each interface.Its value ranges
between 1 and the value of ifNumber.The value for
each interface must remain constant at least from
one re-initialization of the entity's network
management system to the next re-initialization.
ifDescr
.1.3.6.1.2.1.2.2.1.2
DisplayString
RO
A textual string containing information about the
interface.This string should include the name of
the manufacturer, the product name and the
version of the hardware interface.
ifType
.1.3.6.1.2.1.2.2.1.3
Integer
RO
The type of interface, distinguished according to
the physical/link protocol(s) immediately `below'
the network layer in the protocol stack.
ifSpeed
.1.3.6.1.2.1.2.2.1.5
Gauge
RO
An estimate of the interface's current bandwidth in
bits per second.For interfaces which do not vary in
bandwidth or for those where no accurate
estimation can be made, this object should ontain
the nominal bandwidth.
ifPhysAddress
.1.3.6.1.2.1.2.2.1.6
Phys-Address
RO
The interface's address at the protocol layer
immediately `below' the network layer in the
protocol stack. For interfaces which do not have
such an address (e.g., a serial line), this object
should contain an octet string of zero length.
ifAdminStatus
.1.3.6.1.2.1.2.2.1.7
Integer
RW The desired state of the interface. The testing(3)
state indicates that no operational packets can be
passed.
ifOperStatus
.1.3.6.1.2.1.2.2.1.8
Integer
RO
The current operational state of the interface. The
testing(3) state indicates that no operational
packets can be passed.
ifInOctets
.1.3.6.1.2.1.2.2.1.10.x
Counter
RO
The total number of octets received on the
interface, including framing characters.
ifInUcastPkts
.1.3.6.1.2.1.2.2.1.11.x
Counter
RO
The number of subnetwork-unicast packets
delivered to a higher-layer protocol.
ifInNUcastPkts
.1.3.6.1.2.1.2.2.1.12.x
Counter
RO
The number of non-unicast (i.e., subnetworkbroadcast or subnetwork-multicast) packets
delivered to a higher-layer protocol.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
Description
G-4
MIB Parameters
Appendix G
Table G-1: Supported RFC 1213 Variables (Sheet 2 of 2)
Access
Name
OID
Type
Description
ifInErrors
.1.3.6.1.2.1.2.2.1.14.x
Counter
RO
The number of inbound packets that contained
errors preventing them from being deliverable to a
higher-layer protocol.
ifOutOctets
.1.3.6.1.2.1.2.2.1.16.x
Counter
RO
The total number of octets transmitted out of the
interface, including framing characters.
ifOutUcastPkts
.1.3.6.1.2.1.2.2.1.17.x
Counter
RO
The total number of packets that higher-level
protocols requested be transmitted to a
subnetwork-unicast address, including those that
were discarded or not sent.
ifOutNUcastPkts
.1.3.6.1.2.1.2.2.1.18.x
Counter
RO
The total number of packets that higher-level
protocols requested be transmitted to a nonunicast (i.e., a subnetwork-broadcast or
subnetwork-multicast) address, including those
that were discarded or not sent.
a. x is the interface ID
MIB Parameters
Table G-2: Private MIB Parameters (Sheet 1 of 14)
Type
Access
Name
OID
winlink1000OduAdmProductType
1.3.6.1.4.1.4458.1000.1.1.1
DisplayString
RO
ODU configuration description.
winlink1000OduAdmHwRev
1.3.6.1.4.1.4458.1000.1.1.2
DisplayString
RO
ODU Hardware Version.
winlink1000OduAdmSwRev
1.3.6.1.4.1.4458.1000.1.1.3
DisplayString
RO
ODU Software Version.
winlink1000OduAdmLinkName
1.3.6.1.4.1.4458.1000.1.1.4
DisplayString
RW Link Name. A change is effective immediately.
winlink1000OduAdmResetCmd
1.3.6.1.4.1.4458.1000.1.1.5
Integer
RW Reset Command. A set command with a value of 3
will cause a device reset. The read value is always
0.
winlink1000OduAdmAddres
1.3.6.1.4.1.4458.1000.1.1.6
IpAddress
RW ODU IP address. A change is effective after reset.
The parameter is kept for backward compatibility.
Using the alternative parameter:
winlink1000OduAdmIpParamsCnfg is
recommended.
winlink1000OduAdmMask
1.3.6.1.4.1.4458.1000.1.1.7
IpAddress
RW ODU Subnet Mask. A change is effective after
reset. The parameter is kept for backward
compatibility. Using the alternative parameter:
winlink1000OduAdmIpParamsCnfg is
recommended.
winlink1000OduAdmGateway
1.3.6.1.4.1.4458.1000.1.1.8
IpAddress
RW ODU default gateway. A change is effective after
reset. The parameter is kept for backward
compatibility. Using the alternative parameter:
winlink1000OduAdmIpParamsCnfg is
recommended.
winlink1000OduAdmBroadcast
1.3.6.1.4.1.4458.1000.1.1.10
Integer
RW This parameter is reserved for the Manager
application provided with the product.
winlink1000OduAdmHostsTable
Description
N/A Trap destinations table. Each trap destination is
defined by an IP address and a UDP port. Up to 10
addresses can be configured.
winlink1000OduAdmHostsEntry
N/A Trap destinations table entry.
winlink1000OduAdmHostsIndex
RO
winlink1000OduAdmHostsIp
1.3.6.1.4.1.4458.1000.1.1.12.1.2
IpAddress
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
Trap destinations table index.
RW Trap destination IP address. A change is effective
immediately.
G-5
MIB Parameters
Appendix G
Table G-2: Private MIB Parameters (Sheet 2 of 14)
Access
Name
OID
Type
Description
winlink1000OduAdmHostsPort
1.3.6.1.4.1.4458.1000.1.1.12.1.3
Integer
RW UDP port of the trap destination. A change is
effective immediately.
winlink1000OduBuzzerAdminState
1.3.6.1.4.1.4458.1000.1.1.13
Integer
RW This parameter controls the activation of the
buzzer while the unit is in install mode. A change is
effective immediately. The valid values are:
disabled (0) enabled (1).
winlink1000OduProductId
1.3.6.1.4.1.4458.1000.1.1.14
DisplayString
RO
winlink1000OduReadCommunity
1.3.6.1.4.1.4458.1000.1.1.15
DisplayString
RW Read Community String. This parameter always
returns ***** when retrieving its value. It is used by
the Manager application to change the Read
Community String. The SNMP agent accepts only
encrypted values.
winlink1000OduReadWriteCommunity
1.3.6.1.4.1.4458.1000.1.1.16
DisplayString
RW Read/Write Community String. This parameter
always returns ***** when retrieving its value. It is
used by the Manager application to change the
Read/Write Community String. The SNMP agent
accepts only encrypted values.
winlink1000OduTrapCommunity
1.3.6.1.4.1.4458.1000.1.1.17
DisplayString
RW Trap Community String. This parameter is used by
the Manager application to change the Trap
Community String. The SNMP agent accepts only
encrypted values.
winlink1000OduAdmSnmpAgentVersion
1.3.6.1.4.1.4458.1000.1.1.18
Integer
RO
Major version of the SNMP agent.
winlink1000OduAdmRemoteSiteName
1.3.6.1.4.1.4458.1000.1.1.19
DisplayString
RO
Remote site name. Returns the same value as
sysLocation parameter of the remote site.
winlink1000OduAdmSnmpAgentMinorVe
rsion
1.3.6.1.4.1.4458.1000.1.1.20
Integer
RO
Minor version of the SNMP agent.
winlink1000OduAdmLinkPassword
1.3.6.1.4.1.4458.1000.1.1.21
DisplayString
RW Link Password. This parameter always returns
***** when retrieving its value. It is used by the
Manager application to change the Link Password.
The SNMP agent accepts only encrypted values.
winlink1000OduAdmSiteLinkPassword
1.3.6.1.4.1.4458.1000.1.1.22
DisplayString
RW Site Link Password. This parameter always returns
***** when retrieving its value. It is used by the
Manager application to change the Link Password
of the site. The SNMP agent accepts only
encrypted values.
winlink1000OduAdmDefaultPassword
1.3.6.1.4.1.4458.1000.1.1.23
Integer
RO
This parameter indicates if the current Link
Password is the default password.
winlink1000OduAdmConnectionType
1.3.6.1.4.1.4458.1000.1.1.24
Integer
RO
This parameter indicates if the Manager
application is connected to the local ODU or to the
remote ODU over the air. A value of 'unknown'
indicates community string mismatch.
winlink1000OduAdmBackToFactorySetti
ngsCmd
1.3.6.1.4.1.4458.1000.1.1.25
Integer
RW Back to factory settings Command. A change is
effective after reset. The read value is always 0.
winlink1000OduAdmIpParamsCnfg
1.3.6.1.4.1.4458.1000.1.1.26
DisplayString
RW ODU IP address Configuration. The format is:
|||
winlink1000OduAdmVlanID
1.3.6.1.4.1.4458.1000.1.1.27
Integer
RW VLAN ID. Valid values are 1 to 4094. Initial value is
0 meaning VLAN unaware.
winlink1000OduAdmVlanPriority
1.3.6.1.4.1.4458.1000.1.1.28
Integer
RW VLAN Priority. 0 is lowest priority 7 is highest
priority.
This parameter is reserved for the Manager
application provided with the product.
winlink1000OduAdmSN
1.3.6.1.4.1.4458.1000.1.1.29
DisplayString
RO
winlink1000OduSrvMode
1.3.6.1.4.1.4458.1000.1.2.1
Integer
RW System mode. The only value that can be set is
installMode; normalMode reserved to the Manager
application provided with the product. A change is
effective after link re-synchronization.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
IDU Serial Number
G-6
MIB Parameters
Appendix G
Table G-2: Private MIB Parameters (Sheet 3 of 14)
Access
Name
OID
Type
Description
winlink1000OduSrvBridging
1.3.6.1.4.1.4458.1000.1.2.3
Integer
RO
Bridging Mode. Valid values are: disabled (0)
enabled (1).
winlink1000OduEthernetRemainingRate
1.3.6.1.4.1.4458.1000.1.3.1
Integer
RO
Current Ethernet bandwidth in bps.
winlink1000OduEthernetIfTable
N/A ODU Ethernet Interface table.
winlink1000OduEthernetIfEntry
N/A ODU Ethernet Interface table entry.
winlink1000OduEthernetIfIndex
1.3.6.1.4.1.4458.1000.1.3.2.1.1
Integer
RO
ODU Ethernet Interface Index.
winlink1000OduEthernetIfAddress
1.3.6.1.4.1.4458.1000.1.3.2.1.5
DisplayString
RO
ODU MAC address.
winlink1000OduEthernetIfAdminStatus
1.3.6.1.4.1.4458.1000.1.3.2.1.6
Integer
RW Required state of the interface.
winlink1000OduEthernetIfOperStatus
1.3.6.1.4.1.4458.1000.1.3.2.1.7
Integer
RO
winlink1000OduEthernetIfFailAction
1.3.6.1.4.1.4458.1000.1.3.2.1.8
Integer
RW Failure action of the interface.
winlink1000OduEthernetNumOfPorts
1.3.6.1.4.1.4458.1000.1.3.3
Integer
RO
Current operational state of the interface.
Number of ODU network interfaces.
winlink1000OduBridgeBasePortTable
N/A ODU Bridge Ports table.
winlink1000OduBridgeBasePortEntry
N/A ODU Bridge Ports table entry.
winlink1000OduBridgeBasePortIndex
RO
ODU Bridge Port Number.
winlink1000OduBridgeBaseIfIndex
RO
IfIndex corresponding to ODU Bridge port.
winlink1000OduBridgeTpMode
1.3.6.1.4.1.4458.1000.1.4.4.101
Integer
RW ODU bridge mode. A change is effective after
reset. Valid values: hubMode (0) bridgeMode (1).
winlink1000OduBridgeTpPortTable
N/A ODU Transparent Bridge Ports table.
winlink1000OduBridgeTpPortEntry
N/A ODU Transparent Bridge Ports table entry.
winlink1000OduBridgeTpPortIndex
RO
ODU Transparent Bridge Port Number.
winlink1000OduBridgeTpPortInFrames
1.3.6.1.4.1.4458.1000.1.4.4.3.1.3
Counter
RO
Number of frames received by this port.
winlink1000OduBridgeTpPortOutFrames
1.3.6.1.4.1.4458.1000.1.4.4.3.1.4
Counter
RO
Number of frames transmitted by this port.
winlink1000OduBridgeTpPortInBytes
1.3.6.1.4.1.4458.1000.1.4.4.3.1.10 Counter
RO
Number of bytes received by this port.
winlink1000OduBridgeTpPortOutBytes
1.3.6.1.4.1.4458.1000.1.4.4.3.1.10 Counter
RO
Number of bytes transmitted by this port.
winlink1000OduAirFreq
1.3.6.1.4.1.4458.1000.1.5.1
Integer
RW Installation Center Frequency. Valid values are
product dependent. A change is effective after link
re-synchronization.
winlink1000OduAirDesiredRate
1.3.6.1.4.1.4458.1000.1.5.2
Integer
RW Deprecated parameter actual behavior is readonly. Required Air Rate. For Channel Bandwidth of
20 10 5 MHz divide the value by 1 2 4 respectively.
winlink1000OduAirSSID
1.3.6.1.4.1.4458.1000.1.5.3
DisplayString
RW Reserved for the Manager application provided
with the product.
winlink1000OduAirTxPower
1.3.6.1.4.1.4458.1000.1.5.4
Integer
RW Required Transmit power in dBm . This is a
nominal value while the actual transmit power
includes additional attenuation. The min and max
values are product specific. A change is effective
immediately.
winlink1000OduAirSesState
1.3.6.1.4.1.4458.1000.1.5.5
Integer
RO
Current Link State. The value is active (3) during
normal operation.
winlink1000OduAirMstrSlv
1.3.6.1.4.1.4458.1000.1.5.6
Integer
RO
This parameter indicates if the device was
automatically selected into the radio link master or
slave. The value is undefined if there is no link.
winlink1000OduAirResync
1.3.6.1.4.1.4458.1000.1.5.8
Integer
RW Setting this parameter to 1 will cause the link to
restart the synchronization process.
winlink1000OduAirRxPower
1.3.6.1.4.1.4458.1000.1.5.9.1
Integer
RO
Received Signal Strength in dBm.
winlink1000OduAirTotalFrames
1.3.6.1.4.1.4458.1000.1.5.9.2
Counter
RO
Total Number of received radio frames.
winlink1000OduAirBadFrames
1.3.6.1.4.1.4458.1000.1.5.9.3
Counter
RO
Total number of received radio frames with CRC
error.
winlink1000OduAirCurrentRate
1.3.6.1.4.1.4458.1000.1.5.9.4
Integer
RO
Deprecated parameter. Actual rate of the air
interface in Mbps. For Channel Bandwidth of 20 10
5 MHz divide the value by 1 2 4 respectively.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
G-7
MIB Parameters
Appendix G
Table G-2: Private MIB Parameters (Sheet 4 of 14)
Access
Name
OID
Type
Description
winlink1000OduAirCurrentRateIdx
1.3.6.1.4.1.4458.1000.1.5.9.5
Integer
RO
winlink1000OduAirTxPower36
1.3.6.1.4.1.4458.1000.1.5.10
Integer
RW Deprecated parameter. Actual behavior is readonly.
winlink1000OduAirTxPower48
1.3.6.1.4.1.4458.1000.1.5.11
Integer
RW Deprecated parameter. Actual behavior is readonly.
winlink1000OduAirCurrentTxPower
1.3.6.1.4.1.4458.1000.1.5.12
Integer
RO
Index of current air rate.
Current Transmit Power in dBm. This is a nominal
value while the actual transmit power includes
additional attenuation.
winlink1000OduAirMinFrequency
1.3.6.1.4.1.4458.1000.1.5.13
Integer
RO
Minimum center frequency in MHz.
winlink1000OduAirMaxFrequency
1.3.6.1.4.1.4458.1000.1.5.14
Integer
RO
Maximum center frequency in MHz.
winlink1000OduAirFreqResolution
1.3.6.1.4.1.4458.1000.1.5.15
Integer
RO
Center Frequency resolution. Measured in MHz if
value < 100 otherwise in KHz.
winlink1000OduAirCurrentFreq
1.3.6.1.4.1.4458.1000.1.5.16
Integer
RO
Current Center Frequency. Measured in MHz if
center frequency resolution value < 100 otherwise
in KHz.
winlink1000OduAirNumberOfChannels
1.3.6.1.4.1.4458.1000.1.5.17
Integer
RO
Number of channels that can be used.
winlink1000OduAirChannelsTable
N/A Table of channels used by automatic channels
selection (ACS).
winlink1000OduAirChannelsEntry
N/A ACS channels table entry.
winlink1000OduAirChannelsIndex
1.3.6.1.4.1.4458.1000.1.5.18.1.1
Integer
RO
Channel Index.
winlink1000OduAirChannelsFrequency
1.3.6.1.4.1.4458.1000.1.5.18.1.2
Integer
RO
Channel frequency in MHz.
winlink1000OduAirChannelsOperState
1.3.6.1.4.1.4458.1000.1.5.18.1.3
Integer
RW Channel state. Can be set by the user. Automatic
Channel Selection uses channels that are
AirChannelsOperState enabled and
AirChannelsAvail enabled. A change is effective
after link re-synchronization. Valid values: disabled
(0) enabled (1).
winlink1000OduAirChannelsAvail
1.3.6.1.4.1.4458.1000.1.5.18.1.4
Integer
RO
Channel state. Product specific and cannot be
changed by the user. Automatic Channel Selection
uses channels that are AirChannelsOperState
enabled and AirChannelsAvail enabled. Valid
values: disabled (0) enabled (1).
winlink1000OduAirDfsState
1.3.6.1.4.1.4458.1000.1.5.19
Integer
RO
Radar detection state. Valid values: disabled (0)
enabled (1).
winlink1000OduAirAutoChannelSelection 1.3.6.1.4.1.4458.1000.1.5.20
State
Integer
RO
Deprecated parameter. Indicating Automatic
Channel Selection availability at current channel
bandwidth. Valid values: disabled (0) enabled (1).
winlink1000OduAirEnableTxPower
1.3.6.1.4.1.4458.1000.1.5.21
Integer
RO
Indicating Transmit power configuration enabled or
disabled.
winlink1000OduAirMinTxPower
1.3.6.1.4.1.4458.1000.1.5.22
Integer
RO
Minimum Transmit power in dBm.
winlink1000OduAirMaxTxPowerTable
N/A Table of Maximum transmit power per air rate in
dBm.
winlink1000OduAirMaxTxPowerEntry
winlink1000OduAirMaxTxPowerIndex
N/A Maximum Transmit power table entry.
1.3.6.1.4.1.4458.1000.1.5.23.1.1
Integer
RO
Air interface rate index.
Maximum Transmit power in dBm.
winlink1000OduAirMaxTxPower
1.3.6.1.4.1.4458.1000.1.5.23.1.2
Integer
RO
winlink1000OduAirChannelBandwidth
1.3.6.1.4.1.4458.1000.1.5.24
Integer
RW Channel bandwidth in KHz. A change is effective
after reset.
winlink1000OduAirChannelBWTable
N/A Channel Bandwidths table.
winlink1000OduAirChannelBWEntry
N/A Channel Bandwidth table entry.
winlink1000OduAirChannelBWIndex
1.3.6.1.4.1.4458.1000.1.5.25.1.1
Integer
RO
Channel Bandwidth index.
winlink1000OduAirChannelBWAvail
1.3.6.1.4.1.4458.1000.1.5.25.1.2
Integer
RO
Channel Bandwidth availability product specific.
Options are: Not supported supported with manual
channel selection supported with Automatic
Channel Selection.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
G-8
MIB Parameters
Appendix G
Table G-2: Private MIB Parameters (Sheet 5 of 14)
OID
Type
winlink1000OduAirRFD
1.3.6.1.4.1.4458.1000.1.5.26
Integer
winlink1000OduAirRatesTable
Access
Name
RO
Description
Current radio frame duration in microseconds.
N/A Air Rate indexes table for current channel
bandwidth.
winlink1000OduAirRatesEntry
N/A Air Rate indexes table entry.
winlink1000OduAirRatesIndex
1.3.6.1.4.1.4458.1000.1.5.27.1.1
Integer
RO
Air Rate index.
winlink1000OduAirRatesAvail
1.3.6.1.4.1.4458.1000.1.5.27.1.2
Integer
RO
Air Rate availability depending on air interface
conditions.
winlink1000OduAirDesiredRateIdx
1.3.6.1.4.1.4458.1000.1.5.28
Integer
RW Required Air Rate index. 0 reserved for Adaptive
Rate. A change is effective immediately after Set
operation to the master side while the link is up.
winlink1000OduAirLinkDistance
1.3.6.1.4.1.4458.1000.1.5.29
Integer
RO
Link distance in meters. A value of -1 indicates an
illegal value and is also used when a link is not
established.
winlink1000OduAirLinkWorkingMode
1.3.6.1.4.1.4458.1000.1.5.30
Integer
RO
Link working mode as a result of comparing
versions of both sides of the link. Possible modes
are: Unknown - no link Normal - versions on both
sides are identical with full compatibility with
restricted compatibility or versions on both sides
are different with software upgrade or versions
incompatibility.
winlink1000OduAirMajorLinkIfVersion
1.3.6.1.4.1.4458.1000.1.5.31
Integer
RO
Major link interface version
winlink1000OduAirMinorLinkIfVersion
1.3.6.1.4.1.4458.1000.1.5.32
Integer
RO
Minor link interface version
winlink1000OduAirHssDesiredOpState
1.3.6.1.4.1.4458.1000.1.5.40.1
Integer
RW Required Hub Site Synchronization operating
state.
winlink1000OduAirHssCurrentOpState
1.3.6.1.4.1.4458.1000.1.5.40.2
Integer
RO
Current Hub Site Synchronization operating state.
winlink1000OduAirHssSyncStatus
1.3.6.1.4.1.4458.1000.1.5.40.3
Integer
RO
Hub Site Synchronization sync status.
winlink1000OduAirHssExtPulseStatus
1.3.6.1.4.1.4458.1000.1.5.40.4
Integer
RO
Hub Site Synchronization external pulse detection
status.
winlink1000OduAirHssExtPulseType
1.3.6.1.4.1.4458.1000.1.5.40.5
Integer
RO
Hub Site Synchronization external pulse type.
winlink1000OduAirHssDesiredExtPulseT
ype
1.3.6.1.4.1.4458.1000.1.5.40.6
Integer
RW Hub Site Synchronization required external pulse
type. Valid values for read write: {typeA(2)
typeB(3) typeC(4) typeD(5)}. Valid value for read
only: {notApplicable(1)}.
winlink1000OduAirHssRfpTable
N/A ODU Radio Frame Patterns (RFP) Table.
winlink1000OduAirHssRfpEntry
N/A ODU RFP Table entry.
winlink1000OduAirHssRfpIndex
1.3.6.1.4.1.4458.1000.1.5.40.7.1.1 Integer
RO
ODU RFP Table index. The index represent the
Radio Frame Pattern: typeA(2) typeB(3) typeC(4)
typeD(5).
winlink1000OduAirHssRfpEthChannelB
W5MHz
1.3.6.1.4.1.4458.1000.1.5.40.7.1.2 Integer
RO
Represents the compatibility of Ethernet service
under Channel BW of 5MHz in the specific Radio
Frame Pattern.
winlink1000OduAirHssRfpTdmChannelB
W5MHz
1.3.6.1.4.1.4458.1000.1.5.40.7.1.3 Integer
RO
Represents the compatibility of TDM service under
Channel BW of 5MHz in the specific Radio Frame
Pattern.
winlink1000OduAirHssRfpEthChannelB
W10MHz
1.3.6.1.4.1.4458.1000.1.5.40.7.1.4 Integer
RO
Represents the compatibility of Ethernet service
under Channel BW of 10MHz in the specific Radio
Frame Pattern.
winlink1000OduAirHssRfpTdmChannelB
W10MHz
1.3.6.1.4.1.4458.1000.1.5.40.7.1.5 Integer
RO
Represents the compatibility of TDM service under
Channel BW of 10MHz in the specific Radio Frame
Pattern.
winlink1000OduAirHssRfpEthChannelB
W20MHz
1.3.6.1.4.1.4458.1000.1.5.40.7.1.6 Integer
RO
Represents the compatibility of Ethernet service
under Channel BW of 20MHz in the specific Radio
Frame Pattern.
winlink1000OduAirHssRfpTdmChannelB
W20MHz
1.3.6.1.4.1.4458.1000.1.5.40.7.1.7 Integer
RO
Represents the compatibility of TDM service under
Channel BW of 20MHz in the specific Radio Frame
Pattern.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
G-9
MIB Parameters
Appendix G
Table G-2: Private MIB Parameters (Sheet 6 of 14)
Access
Name
OID
Type
winlink1000OduAirLockRemote
1.3.6.1.4.1.4458.1000.1.5.41
Integer
RW This parameter enables locking the link with a
specific ODU. The following values can be set:
Unlock (default) - The ODU is not locked on a
specific remote ODU. Unlock can only be
performed when the link is not connected. Lock The ODU is locked on a specific remote ODU.
Lock can only be performed when the link is
active.
winlink1000OduAirAntennaGain
1.3.6.1.4.1.4458.1000.1.5.42
Integer
RW Current Antenna Gain in 0.1 dBi resolution. User
defined value in case of external antenna. Legal
range:
MinAntennaGain - Alarm.
externalAlarmInPort2Alarm
106
major
The trap is sent every time an alarm occurs in the External Alarm Input of
port #2. Contains a single parameter which is its description: 1 Description: External Alarm 2 -  - Alarm.
bitFailedAlarm
107
critical
The trap is sent in case there is no way to recover from the situation.
Contains two parameters: 1 - Description: ODU power up built in test
failed. Error code is: %n. 2 - %n number.
wrongConfigurationLoadedAlarm
108
major
The trap is sent in case there is a way to recover from the situation.
Contains two parameters: 1 - Description: Wrong configuration loaded.
Error code is: %n. 2 - %n number.
lanPort1DisconnectedAlarm
109
major
Indicates the LAN port 1 status changed to disconnected. Contains a
single parameter which is its description: 1 - Description: LAN port 1
status changed to disconnected.
lanPort2DisconnectedAlarm
110
major
Indicates the LAN port 2 status changed to disconnected. Contains a
single parameter which is its description: 1 - Description: LAN port 2
status changed to disconnected.
mngPortDisconnectedAlarm
111
major
Indicates the management port status changed to disconnected.
Contains a single parameter which is its description: 1 - Description:
Management port status changed to disconnected.
externalAlarmInPort3Alarm
112
major
The trap is sent every time an alarm occurs in the External Alarm Input of
port #3. Contains a single parameter which is its description: 1 Description: External Alarm 3 -  - Alarm.
externalAlarmInPort4Alarm
113
major
The trap is sent every time an alarm occurs in the External Alarm Input of
port #4. Contains a single parameter which is its description: 1 Description: External Alarm 4 -  - Alarm.
swVersionsMismatchFullCompatibilityAlarm
114
warning
The trap is sent in case SW versions mismatch with full link functionality.
Contains a single parameter which is its description: 1 - Description:
Software versions mismatch - full link functionality
swVersionsMismatchRestrictedCompatibilityAlarm
115
minor
The trap is sent in case SW versions mismatch with restricted link
functionality. Contains a single parameter which is its description: 1 Description: Software versions mismatch - restricted link functionality
swVersionsMismatchSoftwareUpgradeRequired
116
major
The trap is sent in case SW versions mismatch and SW upgrade is
required. Contains a single parameter which is its description: 1 Description: Software versions mismatch - Software upgrade required
swVersionsIncompatible
117
critical
The trap is sent in case SW versions are incompatible. Contains a single
parameter which is its description: 1 - Description: SW Versions
incompatible
tdmBackupAlarm
121
major
Indicates that the TDM backup link was activated. Contains a single
parameter, which is its description: 1 - Description: TDM backup alarm backup link was activated.
linkLockUnautorizedRemoteODU
122
major
Indicates that the remote ODU is unautorized. Contains a single
parameter which is its description: 1 - Description: Unauthorized remote
ODU connection rejected.
linkLockUnautorizedODU
123
major
Indicates that the ODU is unautorized. Contains a single
parameter which is its description: 1 - Description: Unauthorized ODU
connection rejected.
tdmServiceClear
200
normal
Indicates that TDM Service fault is cleared. Contains a single parameter,
which is its description: 1 - Description: TDM Service - Normal.
ethServiceOpened
201
normal
Indicates that Ethernet Service has been opened. Contains a single
parameter,3 which is its description: 1 - Description: Ethernet Service has
been opened.
encryptionClear
203
normal
Indicates that encryption is OK. Contains a single parameter which is its
description: 1 - Description: Encryption Status - Normal.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
G-20
RADWIN Manager Traps
Appendix G
Table G-3: MIB Traps (Sheet 4 of 4)
Name
ID
Severity
Description
changeLinkPasswordClear
204
normal
Indicates that the Link Password was changed successfully. Contains a
single parameter which is its description: 1 - Description: Link Password
has been changed at/on: %s. %s - Is the Local Site name or Remote Site
name or both sides of the Link.
externalAlarmInPort1Clear
204
normal
This Trap is sent every time an External Alarm Input fault of port # 1 is
cleared. Contains a single parameter which is its description: 1 Description: External Alarm 1 -  - Alarm Cleared.
externalAlarmInPort2Clear
206
normal
This Trap is sent every time an External Alarm Input fault of port # 2 is
cleared. Contains a single parameter which is its description: 1 Description: External Alarm 2 -  - Alarm Cleared.
lanPort1Clear
209
normal
Indicates the LAN port 1 status changed to connected. Contains two
parameters: 1 - Description: LAN port 1 status changed to connected %s. 2 - %s Is the Eth. mode (speed & duplex).
lanPort2Clear
210
normal
Indicates the LAN port 2 status changed to connected. Contains two
parameters: 1 - Description: LAN port 2 status changed to connected %s. 2 - %s Is the Eth. mode (speed & duplex).
mngPort2Clear
211
normal
Indicates the management port status changed to connected. Contains
two parameters: 1 - Description: Management port status changed to
connected - %s. 2 - %s Is the Eth. mode (speed & duplex).
externalAlarmInPort3Clear
211
normal
This Trap is sent every time an External Alarm Input fault of port # 3 is
cleared. Contains a single parameter which is its description: 1 Description: External Alarm 3 -  - Alarm Cleared.
externalAlarmInPort4Clear
213
normal
This Trap is sent every time an External Alarm Input fault of port # 4 is
cleared. Contains a single parameter which is its description: 1 Description: External Alarm 4 -  - Alarm Cleared.
swVersionsMatchFullCompatibilityClear
214
normal
The trap is sent in case SW versions match. Contains a single parameter
which is its description: 1 - Description: Software Versions compatible
swVersionsMatchRestrictedCompatibilityClear
215
normal
The trap is sent in case SW versions match and link functionality is not
restricted. Contains a single parameter which is its description: 1 Description: Software Versions compatible
swVersionsMatchSoftwareUpgradeRequiredClear
216
normal
The trap is sent in case SW versions match and SW upgrade is
successful. Contains a single parameter which is its description: 1 Description: Software Versions compatible
swVersionsCompatibleClear
217
normal
The trap is sent in case SW versions compatible Contains a single
parameter which is its description: 1 - Description: Software Versions
compatible
tdmBackupClear
221
normal
linkLockAutorizedODU
223
normal
Indicates that the ODU is autorized. Contains a single parameter which
is its description: 1 - Description: Authorized ODU connection permitted.
linkAuthenticationDisabled
224
normal
Indicates that the Link Lock is disabled. Contains a single parameter
which is its description: 1 - Description: Link Authentication has been
disabled
RADWIN Manager Traps
The RADWIN Manager application issues traps to indicate various events.
These traps are shown in the RADWIN Managerr Events Log.
A list of Trap Messages as displayed by the RADWIN Manager is shown in
table 7-5.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
G-21
Appendix H
External Alarms
Specification
External Alarms Specification
The IDU-C supports external input and output alarms through a standard
DB25 pin female connector.
Input alarms
The input alarms are raised by events from external equipment, such as
a fire warning, door open or air conditioner failure.
Output alarms
Output alarms are generated through dry contact relays to indicate various system events according to the following table. An alarm is raised if
at least one of the conditions is met.
Table H-1: Output Alarms Pinout
Alarm
Description
Alarm On Conditions
Alarm Off Condition
Output 1
Air interface Alarm
•
•
•
Link is down
Link in installation mode
Link authentication problem
Output 2
Equipment Alarm
•
•
•
Both ODU and IDU are in
Built in Test (BIT) error
operational state
No connection to the ODU
Incompatible software
Output 3
Service Alarm at Site B
N/A
Permanently off
Output 4
Power Failure at Site B
Link Loss due to Power Failure
at Site B
Link is up or down without power failure indication within the last two
seconds
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
Link is up
H-1
Appendix I
Combo Configuration Tool
What is the Combo Configuration Tool?
The RADWIN 1000/2000/5000 is supplied preconfigured to a default frequency band and regulation. The user may however, reconfigure it to use
any one of the supported frequency bands shown in the following example:
Product
Default Band
FCC/IC 5.8 GHz
FCC/IC 5.3 GHz
2050
FCC/IC 5.4 GHz
FCC/IC 4.9 GHz
FCC/IC 2.4 GHz
The Combo Configuration Tool is a software utility supplied by RADWIN to
change the link frequency band. It runs as familiar Windows Wizard.
This appendix will walk you through the Wizard. It also provides help for
common problems encountered during the configuration.
Who may use the Combo Configuration Tool
The Combo Configuration Tool is a password protected utility intended for
the use of RADWIN accredited personnel at the user’s site, RADWIN Customer Support Engineers or Professional Installers conversant with FCC
requirements.
Caveat to the use of the Combo Configuration Tool
It is the user’s responsibility to operate the system according to local regulations and to acquire the relevant permits or licenses for the frequency band
selected, if applicable.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
I-1
Prerequisites to using the Combo Configuration Tool
Appendix I
Prerequisites to using the Combo Configuration Tool
To use the Tool, you need a PC running Windows 2000 or Windows XP Pro
to be connected to the RADWIN 1000/2000/5000 link.
Operating the Combo Configuration Tool
The tool is supplied as an executable called ComboConfigurationTool.exe. It
should be copied to a convenient directory on a hard disk from where it can
be run from a command line, or placed on the desktop and opened with a
double click.
The Combo Configuration Tool is a Wizard, which guides you through the
process of changing the frequency band.
Before using the Combo Configuration Tool
Before starting:
 Obtain the IP address of both the local ODU and remote ODUs of
the link
 Make a note of the correct required frequency band
 If the link uses external antennas, ensure that they support your
required frequency band
Also, note that
1. The procedure below must be carried out for both ODUs in the link.
2. Changing the frequency band may affect the available Link Budget and
system performance.
Using the Combo Configuration Tool
 To change the link frequency band:
1. Open the Tool from a command line or double clicking it on the desktop.
The following Welcome screen appears:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
I-2
Using the Combo Configuration Tool
Appendix I
2. Click Next. The window below is displayed:
3. Enter the ODU IP address and password.
4. Click Next. The following progress panel is displayed:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
I-3
Using the Combo Configuration Tool
Appendix I
Upon completion the following screen is displayed:
The checked item is the currently configured frequency band.
5. Check the box with the required frequency band. If you do not see the
required frequency band in the above window, click Cancel and consult
RADWIN Customer Support.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
I-4
Using the Combo Configuration Tool
Appendix I
6. Otherwise, click Next. The following window is displayed:
7. If the legal notice is acceptable, click the “I accept” radio button, and
then click Next. Two successive progress panels are displayed. The configuration may take several minutes.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
I-5
If you receive an error message
Appendix I
Upon successful completion of the configuration process, the following
termination window is displayed:
8. Click Finish to exit the Wizard as shown.
9. Repeat the whole process for the second ODU in the link.
If you receive an error message
The last stage above may terminate unsuccessfully due to an error. Error
messages are posted to a window like this:
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
I-6
If you receive an error message
Appendix I
The following table sets out possible errors:
Error Number Error Text Message
(nn)
Common message preamble:
The Configure procedure has failed with the following error: ERROR nn
occurred:
120
Failed to communicate with the ODU. Please verify the existence of a stable IP connection and try again.
940
Product is not identified.
1040
The ODU is not a Combo product.
1020
A configuration problem detected. Aborting.
The only items requiring explanation are errors 940 and 1020.
Error 940 may arise as a result of an ODU firmware problem. Error 1020 will
appear for any reason not caught by the other entries in the table. In all
such cases, you should consult with RADWIN Customer Support.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
I-7
Appendix J
Regional Notice: French
Canadian
Procédures de sécurité
Généralités
Avant de manipuler du matériel connecté à des lignes électriques ou de
télécommunications, il est conseillé de se défaire de bijoux ou de tout autre
objet métallique qui pourrait entrer en contact avec les éléments sous tension.
Mise à la terre
Tous les produits RADWIN doivent être mis à la terre pendant l'usage courant. La mise à la terre est assurée en reliant la fiche d'alimentation à une
prise de courant avec une protection de terre. En outre:
•
La cosse de masse sur l'IDU-C doit être constamment connectée à
la protection de terre, par un câble de diamètre de 18 AWG ou plus.
Le matériel monté sur rack doit être installé seulement sur des racks
ou armoires reliés à la terre
•
Une ODU doit mise à la terre par un câble de diamètre de 12 AWG
ou plus
•
Il ne doit pas y avoir de fusibles ou d'interrupteurs sur la connection
à la terre
De plus:
•
Il faut toujours connecter la terre en premier et la déconnecter en
dernier
•
Il ne faut jamais connecter les câbles de télécommunication à du
matériel non à la terre
•
Il faut s'assurer que tous les autres câbles sont déconnectés avant
de déconnecter la terre
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
J-1
Protection contre la foudre
Appendix J
Protection contre la foudre
L'utilisation de dispositifs de protection contre la foudre dépend des exigences réglementaires et de l'utilisateur final. Toutes les unités extérieures
RADWIN sont conçues avec des circuits de limitation de surtension afin de
minimiser les risques de dommages dus à la foudre. RADWIN conseille l'utilisation d'un dispositif de parafoudre supplémentaire afin de protéger le
matériel de coups de foudre proches.
Matériel supplémentaire requis
L'équipement requis pour l'installation du matériel est le suivant:
•
Pince à sertir RJ-45 (si un câble pré-assemblé ODU/IDU n'est pas
utilisé)
•
Perceuse (pour le montage sur mur seulement)
•
Câbles de terre IDU et ODU
•
Clef 13 mm (½)
•
Câble ODU - IDU si non commandé (type extérieur, CAT-5e, 4 paires
torsadées, 24 AWG)
•
Colliers de serrage
•
Ordinateur portable avec Windows 2000 ou Windows XP.
Précautions de sécurité pendant le montage de ODU
Avant de connecter un câble à l'ODU, la borne protectrice de masse (visse)
de l'ODU doit être connectée à un conducteur externe protecteur ou à un
pylône relié à la terre. Il ne doit pas y avoir de fusibles ou d'interrupteurs
sur la connection à la terre.
Seulement un personnel qualifié utilisant l'équipement de sécurité approprié
doit pouvoir monter sur le pylône d'antenne. De même, l'installation ou le
démontage de ODU ou de pylônes doit être effectuée seulement par des
professionnels ayant suivi une formation.
 Pour monter l'ODU:
1. Vérifier que les supports de fixation de l'ODU sont correctement mis à la
terre.
2. Monter l'unité ODU sur le pylône ou sur le mur; se référer à la Installation sur pylône et mur au dessous.
3. Connecter la câble de terre au point de châssis sur l'ODU.
4. Relier le câble ODU-IDU au connecteur ODU RJ-45.
5. Visser les presses-étoupe de câbles pour assurer le scellement hermétique des unités ODU.
6. Attacher le câble au pylône ou aux supports en utilisant des colliers classés UV.
7. Répéter la procédure sur le site distant.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
J-2
Connecter la terre à IDU-C
Appendix J
Ne pas se placer en face d'une ODU sous tension.
Prudence
Connecter la terre à IDU-C
Connecter un câble de terre de 18 AWG à la borne de masse de l'appareil.
L'appareil doit être constamment connecté à la terre.
Prudence
•
Les appareils sont prévus pour être installés par un personnel de service.
•
Les appareils doivent être connectés à une prise de courant avec une
protection de terre.
•
Le courant CC du IDU-C doit être fourni par l'intermédiaire d'un disjoncteur bipolaire et le diamètre du câble doit être de 14 mm avec un
conduit de 16 mm.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
J-3
Installation sur pylône et mur
Appendix J
Installation sur pylône et mur
L' ODU ou l'O-PoE peuvent être montés sur un pylône ou un mur.
Contenu du kit de montage ODU
Le kit de montage ODU comprend les pièces suivantes:
•
une grande clame (voir figure J-1)
•
une petite clame (voir figure J-2)
•
un bras (voir figure J-3)
•
quatre visses hex tête M8x40
•
deux visses hex tête M8x70
•
quatre rondelles plates M8
•
trois rondelles élastiques M8
•
deux écrous M8.
Figure J-1: grande clame
Figure J-2: petite clame
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
Figure J-3: bras
J-4
Montage sur un pylône
Appendix J
Montage sur un pylône
Figure J-4: Montage sur un pylône
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
J-5
Montage sur un mur
Appendix J
Montage sur un mur
Figure J-5: Montage sur un mur
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
J-6
Montage d'une antenne externe
Appendix J
Montage d'une antenne externe
L'antenne externe optionnelle peut être montée sur un pylône.
Contenu du kit de montage d'une antenne externe
Le kit de montage d'une antenne externe comprend les pièces suivantes
•
Douze rondelles plates
•
Huit rondelles élastiques
•
Huit écrous hex
•
Quatre boulons
•
Un support en U
•
Un support à pivotement
•
Deux courroies de fixation en métal
 Pour installer une antenne externe sur un pylône:
1. Attacher le support en U à l'arrière de l'antenne en utilisant quatre rondelles plates, quatre rondelles élastiques et quatre écrous hex.
2. Attacher le support à pivotement au support en U en utilisant huit rondelles plates, quatre rondelles élastiques, quatre écrous hex et quatre
boulons.
3. Passer les deux courroies de fixation par les fentes verticales dans le support à pivotement.
4. Attacher l'antenne au pylône en utilisant les deux courroies de fixation .
Ajuster l'inclinaison nécessaire en utilisant l'échelle angulaire et serrer tous
les boulons et écrous à la position requise.
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
J-7
Index
Index
AAR
1-4
4-17, 6-20, G-8, G-8
ACS
6-10
aging time, ODU Bridge Mode
1-12, 1-12
Air Interface
A-1
Technical Specifications, general
Alarms
7-9
Active
7-14
summary
B-3
Connector
H-1
External , specification
Antennas
3-13
Align with beeper
3-13
Aligning
3-13
bipolar
3-14
Buzzer signals
3-14
monopolar
E-1
Cable, grounding
3-13
Connecting
1-10
Described
External
3-7
Mounting
3-5
Package Contents
C-3
External, Mounting
1-11
Flat panel
1-12
Parabolic Dish
4-19, 5-18
Settings
1-8
types
Applications
1-2
Broadband Access
1-2
IP Backhaul
1-3
Private Networks
1-2
WiMAX
1-4
Automatic Adaptive Rate, see AAR
Automatic Channel Selection, see ACS
1-4
Automatic Repeat Request
backup
configuration file
ODU replacement
Beeper
mute
muting and restoring
restore
6-2
7-16
Bridge mode,Telnet commands
Buzzer, see Beeper
6-21
Changing link password
4-16
4-17, 5-12
Channel, selecting
Community Strings
6-16
Changing
6-15
Editing
6-14, G-2
Factory Default
6-16
Forgotten passwords
G-2
MIB
4-4
passwords
6-14
Read-Only
6-14
Read-Write
6-14
Trap
6-3
Configuration Parameters
Configuring
6-2, 6-9, 6-11, 6-12, 6-18
Advanced
6-2
Air Interface
5-1
Air interface
6-1
Bridge mode
6-1
Community values.
6-2
contact person
6-2
Date and Time
6-1
Ethernet mode
5-1
Frequency channel
6-2
Security
5-1
Service parameters
6-2
System
5-1
System parameters
6-1
Transmit power
6-2
View Inventory
4-17, 5-12
Connecting user equipment
7-17
Customer Support
Date and time, setting
Default log on password
DFS
Configuration
Link Activation
6-2, 6-7
4-4
F-1
F-5
F-2
6-17
6-3
6-17
RADWIN 1000/2000/5000 User ManualVersion 2.6.50p1
Index 1
E
Transmission (Tx) power
1-4
Events
color codes
log
priority
7-12
7-2, 7-4
7-13
Factory Defaults
6-14, G-2
6-19
Reset to
Factory Setup
7-17
Restoring
F-1
FCC/IC DFS Installation Procedure
4-21, 4-22, A-4, A-4
FEC
Forward Error Correction, see FEC
Gateway
Telnet display
6-2
6-20
IDU
6-10
Aging time
6-10
aging time, ODU Bridge Mode
3-12
Connecting to ODU
1-8
described
IDU-C
B-3
Alarm Connector
B-4
Connectors
1-9
Front panel
3-10
Described
3-10, 3-11, 4-2
LEDs
3-8
Mounting
3-11, 3-12
Power connections
3-4
Package Contents
1-8
Products
Indoor Unit, see IDU
Installation
4-10
Menu and Toolbar Functionality
5-22
Post Configuration main window
4-27
Post Installation main window
see Link, Installation
6-3, 6-3, 6-12
Installation Mode
6-16
Inventory
6-12
Displaying
6-2
IP address
6-20
Telnet display
Key Features of Radio Link
Advanced Air Interface
Capacity
Combo Frequency Products
Installation and management
Range performance
Security
Spectral Efficiency
1-4
1-3
1-4
1-4
1-4
1-5
1-3
LBC
7-4
D-6
Browser warnings
D-2
Calculations
D-10
Climactic C Factors
D-1
described
D-13
Fresnel Zone, described
D-1
Internal data
D-3
Running
D-1
User input
E-1
Lightning and Grounding Guidelines
Link
Budget Calculator, see LBC
5-1
Configuration
5-10
Overview
5-11
Step 1 - Start Wizard
5-11
Step 2- System Parameters
5-12
Step 3 - Channel Settings
Step 4 - Tx Power and Antenna Settings
5-18
5-20
Step 5 - Services
5-21
Step 6 - Summary and exit
4-18
default frequency
4-9
default Settings
7-1
Information
Air Interface Thresholds
7-9
BBER Threshold
7-9
RSL Threshold
7-9
Air Interface Thresholds, setting
Alarms
7-14
Active summary
7-14
Error detection and
7-15
output
7-14
saved
7-3
Compatibility
7-3
Trap messages
7-4
Events Log
Events log
Events references
trap
7-13
background color
7-13
default colors
7-12
foreground color
7-12
Preferences
7-13
saving
7-4, 7-4
Monitor log
7-4
saving
7-17
Online Help
7-8
Performance data, explained
7-4
Performance monitoring
7-5
Performance Reports
7-15
Remote Power Fail Indication
7-15
“Dying-Gasp” circuit
7-16
Troubleshooting
4-7
Installation
RADWIN 1000/2000/5000 User ManualVersion2.6.50p1
Index 2
ODU
C-1
Mast and Wall
4-13
Overview
4-14
Step 1 - Start Wizard
4-14
Step 2 - System Parameters
4-17
Step 3 - Channel Settings
Step 4 - Tx Power and Antenna Settings
4-19
4-20
Background
4-25
Step 5 - Services
4-26
Step 6 - Summary and Exit
4-9, 4-15, 6-20, 7-16, 7-16, 7-17
Link ID
4-3
Login
Login Errors
4-6
Incorrect IP Address
4-6
Incorrect password
4-5
Unsupported Device
4-5
Login showing Community Options
4-2
Manager Software
4-15
Name
1-5, 7-17
Password
4-16
changing
5-22
Post Configuration main window
4-27
Post Installation main window
7-3
Reinstalling/Realigning
4-15
Site names
7-4
Link Budget Calculator, see LBC
4-9, 4-15, 6-20, 7-16, 7-16, 7-17
Link ID
Link Site
2-1
Planning
2-1
Survey
2-2
Stage 1 - Preliminary Survey
2-3
Stage 2 - Physical Survey
Additional Indoor Site Requirements
2-4
Additional Outdoor Site Requirements
2-4
2-4
Stage 3 - RF Survey
Login Errors
4-6
Incorrect IP Address
4-6
Incorrect password
4-5
Unsupported Device
Management
Addresses
and trap addresses
Configuring the Site
Screen, Telnet
Manager Software
Change log on password
Events Log
Installing
Main window
Details pane
Main menu
Toolbar
6-4
6-1
6-2
6-22
4-7
5-8
4-1
5-1
5-6
5-3
5-2
main window
Monitor pane
Ethernet Service
4-5
5-7
5-7
5-7
Radio Interface,
5-7
Radio signal strength
4-6
Off-line functionality
5-9
Status Bar
Manual
1-14
Chapters by Audience
1-16
Conventions
1-14
Terminology
MIB
G-1
About
G-2
Community String
G-1
Interface API
G-4
Parameters
G-2
Private
G-5
Private Parameters
G-1
Reference
Supported Variables from the RFC 1213 G-4
G-1
Terminology
G-18
Traps
G-18
Parameters
ODU
Bridge Mode
aging time
Connectorized
described
form factors
Installation, Mast and Wall
Integrated Antenna
Mounting Kit
Package Contents
Products
Replacing
With integrated antenna
1-7
6-10
1-6, 1-7
1-6
1-7
C-1
1-6, 1-7
C-1
3-2
1-8
7-16
1-10
Package, contents of
3-2
Password
4-4, 4-4
Community
4-4
Default
4-4
default log on
1-5, 7-17
Link
4-1
PC, Minimum Requirements
Performance
7-2
Monitor
7-4
Performance Monitoring, set time interval
PoE
1-9
Described
PoE device, see PoE
Power over Ethernet, see PoE
Protection
E-3
External Lightning Surge Suppressors
RADWIN 1000/2000/5000 User ManualVersion2.6.50p1
Index 3
Grounding
Antenna cable
IDUs
ODUs
Internal ESD Protection circuits
E-1
E-2
E-2
E-7
Radio Link
1-13
Accessories
Additional Tools and Materials Required 3-5
3-12
Connecting user equipment
1-5
Described
1-13
Documentation set
Hardware Installation
3-7
External Antennas
3-8
Indoor
3-7
Lightning protection
3-8
Mounting U
3-6
ODU
3-6
Outdoor
3-8
Outdoor connections
3-5
Sequence
3-2
Package Contents
3-4
IDU
3-2
ODU
Package contents
3-5
External Antennas
4-22
Transmission rates
Radio Outdoor Unit, see ODU
7-16
Replacing an ODU
6-2
restore configuration file
Safety Practices
3-1
3-1
Grounding
Preventing overexposure to RF energy 3-1
4-17, 5-12
Selecting channel
Site
Configuration
6-18
Configuration Files
6-18
backup to
Configuration files
6-19
restore from
6-20
Configuration with Telnet
Dialog
6-4
Change Tx Power
6-9
Ethernet Properties
Configuring
6-9
Bridge
Maximum information rate 6-12
6-11
Ports Mode
Ethernet PropertiesIDU Aging time 610
6-2
Functions
6-12
Inventory
6-2
Menu bar
6-7
Setting the date and time
6-3
View Air Iinterface details
6-5
VLAN Settings
Lost or forgotten VLAN ID 6-7
6-6
Priority number
6-6
VLAN ID
6-17
External Alarm Inputs
6-19
Reset site
6-19
Reset site to factory defaults
Reset site, preserve current configuration
6-19
6-13
Security Features
6-14
Community Strings
6-15
Editing
6-16
Forgotten paswwords
6-15
Initial log on defaults
6-5
Default Gateway
6-5, 6-5
IP address
6-5
Trap Destination
Technical Specifications
Air Interface
Air Interface, general
Configuration
EMC
Environmental
Ethernet Interface
Management
Mechanical
Power
Safety
Trap messages
typical installation
A-6
A-1
A-1
A-6
A-5
A-5
A-5
A-5
A-5
A-6
7-3
3-5
User equipment, connecting
4-17, 5-12
Wiring Specifications
Alarm
Connector
IDU-C
Connectors
IDU-C
User Port
LAN
Ports
ODU-IDU Cable
Ports
LAN
User Port Connectors
RADWIN 1000/2000/5000 User ManualVersion2.6.50p1
B-1
B-3
B-4
B-1
B-1
B-1
B-1
B-1
Index 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : DAF
Create Date                     : 2011:10:24 08:45:51Z
Modify Date                     : 2011:10:27 13:33:59+02:00
Subject                         : 1.790 User Manual
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : FrameMaker 10.0.1
Metadata Date                   : 2011:10:27 13:33:59+02:00
Format                          : application/pdf
Title                           : STW
Creator                         : DAF
Description                     : 1.790 User Manual
Producer                        : Acrobat Distiller 10.1.1 (Windows)
Document ID                     : uuid:1ca50a1a-7657-449a-8e1c-e15bf0c062c0
Instance ID                     : uuid:d18455a4-f6c9-44d4-a631-c4ed75c7e080
Page Mode                       : UseOutlines
Page Count                      : 125

EXIF Metadata provided by EXIF.tools