Raven E1003925 Remote Control Transmitter User Manual 99300799 pmd

Raven Industries Remote Control Transmitter 99300799 pmd

User Manual

EDR10488 4/05Document Part No. 99300799© Leggett & Platt, Inc.OPERATION GUIDEMASSAGE NOTE:When activated, the massage system will launch the prior intensity setting used and automaticallyshut off after 30 minutes. To restart Neurosage wave, press the Neurosage on/off button. To restarthead or foot massagers, press the “+” symbol on the head or foot massage button/s.IMPORTANT:Read advisory information in the owners manual carefully before using this product. Thepotential for electrical shock exists if electrical components are not installed or operatedproperly.See back of page for additional programming features...FOOT UP/DOWN BUTTONPress and hold to raise orlower the foot section.HEAD UP/DOWN BUTTONPress and hold to raise orlower the head section.POSITION RECALL BUTTONSPress to activate a position setby the program button.FLAT BUTTONPress to return bedto the level position.HEAD MASSAGE BUTTONPress the “+” symbol to activate thehead massager at a preset intensity.Press and hold the “+” symbol tointensify head massager. Press andhold the “–” symbol to decrease headmassager intensity.PROGRAM SET BUTTONPress to capture any positionof the bed as a programmedposition (3 unique positions).Press the recall buttons (“P1,P2 or P3”) to return bed toany of the preset positions.To Program Preset Positions:1. Set the head and/or foot tothe desired position.2. Press the program set buttononce.3. Press position recall button“P1” to save position.4. Repeat steps 1 thru 3 aboveto program favorite positionsfor “P2” and “P3”.TRANSMISSIONINDICATOR LIGHTFOOT MASSAGE BUTTONPress the “+” symbol toactivate the foot massager ata preset intensity. Press andhold the “+” symbol tointensify foot massager. Pressand hold the “–” symbol todecrease foot massagerintensity.STOP BUTTONPress to immediately stopall active bed functions.NEUROSAGE ON/OFF BUTTONPress to activate or deactivatethe Neurosage wave vibrationsystem.NEUROSAGE WAVE INTENSITY BUTTONPress and hold the “+” symbol to intensifyNeurosage wave intensity. Press and holdthe “–” symbol to decrease Neurosagewave intensity.www.lpadjustablebeds.com
4002 BATTERY REPLACEMENTRequires (2) CR2032 3 volt batteries.REMOVAL:1. Remove the batterycompartment coverlocated on the back ofthe hand control(FIGURE 1).2. Press the round-shaped tab (FIGURE 2)and each battery willeject from the plasticcaptive clip (FIGURE 3).3. Grasp and removebatteries. Noteposition of batterieswhen removing forreplacement.REPLACEMENT:4. Position the newbatteries face-upand insert into theplastic captive clips(reverse of removal).5. Carefully pushbatteries in anddown to install.6. Replace batterycompartment cover.FIGURE 1PUSH IN (SLIGHTLY)AND SLIDE OFFBATTERYCOMPARTMENTCOVERFIGURE 3WHEN BATTERY EJECTSFROM CAPTIVE CLIP,ROTATE UP AND OUTOF BATTERYCOMPARTMENTTO REMOVE4002 PROGRAMMINGTo set channels on a single base:1. Plug the bed into a powersource and within 30 seconds,press the head up button onthe hand control until thetransmission indicator lightilluminates. This will confirmthat the hand control and thebed are communicating.2. The hand control channel isnow programmed.To set channels for 2 or morebeds to operate independently:1. Unplug all beds from theirpower sources.2. Plug in the first bed to beprogrammed and within 30seconds, press the head upbutton on the hand control untilthe transmission indicator lightilluminates. This will confirmthat the hand control and thebed are communicating.3. Repeat steps 1 and 2 with eachbase requiring programming (Itis important to use the specifichand control that will be usedto operate the bed). Beds priorprogrammed with the remoteneed not be unplugged.4. Multiple beds are nowprogrammed for independentoperation.Note: In the event of powerfailure or if bed is inadvertentlyunplugged from the electricalpower source, wait 30 seconds(after power is restored) beforeusing any hand control. Thiswill prevent bases fromlearning and workingsimultaneously.FIGURE 2PUSH DOWNON TAB TOEJECT BATTERIESBATTERIES
Re: Certification for Raven Transmitter Model(s): E1003925 FCC ID: KSME1003925 IC: 2004A-E1003925 USER'S MANUAL INFORMATION (PRELIMINARY) The User's Manual is in preparation. The following material will also be contained in the manual: WARNING: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.

Navigation menu