Raven E1003925 Remote Control Transmitter User Manual 99300799 pmd
Raven Industries Remote Control Transmitter 99300799 pmd
Raven >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 679123 |
| Application ID | o0dNDNHtIb0A5rDtsX3JXQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 9.98kB (124771 bits) |
| Date Submitted | 2006-07-10 00:00:00 |
| Date Available | 2006-07-10 00:00:00 |
| Creation Date | 2006-07-05 13:15:42 |
| Producing Software | Acrobat Distiller 6.0.1 (Windows) |
| Document Lastmod | 2006-07-10 15:07:34 |
| Document Title | 99300799.pmd |
| Document Creator | PageMaker 7.0 |
| Document Author: | abumls1 |
OPERATION GUIDE TRANSMISSION INDICATOR LIGHT HEAD UP/DOWN BUTTON Press and hold to raise or lower the head section. PROGRAM SET BUTTON Press to capture any position of the bed as a programmed position (3 unique positions). Press the recall buttons (“P1, P2 or P3”) to return bed to any of the preset positions. To Program Preset Positions: 1. Set the head and/or foot to the desired position. 2. Press the program set button once. 3. Press position recall button “P1” to save position. 4. Repeat steps 1 thru 3 above to program favorite positions for “P2” and “P3”. HEAD MASSAGE BUTTON Press the “+” symbol to activate the head massager at a preset intensity. Press and hold the “+” symbol to intensify head massager. Press and hold the “–” symbol to decrease head massager intensity. STOP BUTTON Press to immediately stop all active bed functions. FLAT BUTTON Press to return bed to the level position. FOOT UP/DOWN BUTTON Press and hold to raise or lower the foot section. POSITION RECALL BUTTONS Press to activate a position set by the program button. FOOT MASSAGE BUTTON Press the “+” symbol to activate the foot massager at a preset intensity. Press and hold the “+” symbol to intensify foot massager. Press and hold the “–” symbol to decrease foot massager intensity. NEUROSAGE ON/OFF BUTTON Press to activate or deactivate the Neurosage wave vibration system. NEUROSAGE WAVE INTENSITY BUTTON Press and hold the “+” symbol to intensify Neurosage wave intensity. Press and hold the “–” symbol to decrease Neurosage wave intensity. MASSAGE NOTE: When activated, the massage system will launch the prior intensity setting used and automatically shut off after 30 minutes. To restart Neurosage wave, press the Neurosage on/off button. To restart head or foot massagers, press the “+” symbol on the head or foot massage button/s. IMPORTANT: Read advisory information in the owners manual carefully before using this product. The potential for electrical shock exists if electrical components are not installed or operated properly. See back of page for additional programming features... EDR10488 4/05 Document Part No. 99300799 www.lpadjustablebeds.com © Leggett & Platt, Inc. 4002 PROGRAMMING To set channels on a single base: 1. Plug the bed into a power source and within 30 seconds, press the head up button on the hand control until the transmission indicator light illuminates. This will confirm that the hand control and the bed are communicating. 2. The hand control channel is now programmed. To set channels for 2 or more beds to operate independently: 1. Unplug all beds from their power sources. 4002 BATTERY REPLACEMENT Requires (2) CR2032 3 volt batteries. REMOVAL: 1. Remove the battery compartment cover located on the back of the hand control (FIGURE 1). 2. Press the roundshaped tab (FIGURE 2) and each battery will eject from the plastic captive clip (FIGURE 3). 3. Grasp and remove batteries. Note position of batteries when removing for replacement. 2. Plug in the first bed to be programmed and within 30 seconds, press the head up button on the hand control until the transmission indicator light illuminates. This will confirm that the hand control and the bed are communicating. 3. Repeat steps 1 and 2 with each base requiring programming (It is important to use the specific hand control that will be used to operate the bed). Beds prior programmed with the remote need not be unplugged. FIGURE 2 BATTERIES FIGURE 1 REPLACEMENT: 4. Position the new batteries face-up and insert into the plastic captive clips (reverse of removal). 5. Carefully push batteries in and down to install. PUSH DOWN ON TAB TO EJECT BATTERIES 4. Multiple beds are now programmed for independent operation. Note: In the event of power failure or if bed is inadvertently unplugged from the electrical power source, wait 30 seconds (after power is restored) before using any hand control. This will prevent bases from learning and working simultaneously. PUSH IN (SLIGHTLY) AND SLIDE OFF BATTERY COMPARTMENT COVER 6. Replace battery compartment cover. WHEN BATTERY EJECTS FROM CAPTIVE CLIP, ROTATE UP AND OUT OF BATTERY COMPARTMENT TO REMOVE FIGURE 3 Re: Certification for Raven Transmitter Model(s): E1003925 FCC ID: KSME1003925 IC: 2004A-E1003925 USER'S MANUAL INFORMATION (PRELIMINARY) The User's Manual is in preparation. The following material will also be contained in the manual: WARNING: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 3 XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:bc9b15bf-bbb2-4854-9f32-0e0c8d8a586e Producer : Acrobat Distiller 6.0.1 (Windows) Creator Tool : PageMaker 7.0 Modify Date : 2006:07:10 15:07:34-04:00 Create Date : 2006:07:05 13:15:42-04:00 Metadata Date : 2006:07:10 15:07:34-04:00 Document ID : uuid:7bb2b5ea-75b1-4bbf-a0b7-9d2b6f2f2cae Format : application/pdf Title : 99300799.pmd Creator : abumls1 Author : abumls1EXIF Metadata provided by EXIF.tools