Rentokil Initial 1927 plc GSD-500349 LongReach Radio Module User Manual Title page image

Rentokil Initial 1927 plc LongReach Radio Module Title page image

Users Manual - MMT

Adam O’Callaghan/JMcMulti Mouse Trap Connect (MMT) User Guide16-04-18 –GSD-100694 Version 1.0
2MMT - Overview•Retrofittable to TinCat models from Victor and JT Eaton. •Retrofittable to Little Pete models from JT Eaton•Battery Powered•Reports activations directly to PestNet Online•Based on RI Connect LongReach 868/915MHz Technology
3Introduction to the PestConnect SystemMMT Connect UnitsControl Panel
4MMT Technical DetailsBattery Supply2 x AA Cell Alkaline BatteriesDimensions 112mm x 38mm x 60mmMaterial 20% Glass Filled PCWeight 173gOperating Temperature -20 to +50 CelciusMounting JT Eaton & Victor TinCat’sJT Eaton Little PeteStandards/Certifications FCCIP Rating IP67
5Product Exploded View
6MMT Sensor –Key Hardware Features 1 / 2Infra Red light Sensors scan inside the trap, monitoring for rodent activity.2 x Hidden until lit LED’s show the technician the status of the trap
7MMT Sensor –Key Hardware Features 2 / 2Battery compartment –housing 2 x AA Alkaline Batteries
8In box componentsLive Catch Connect SensorAnti reflection labelRubber Bungs (x2) Fixing Bolts (x2)NB: For each box of 10 x MMT sensors 1x Pest Key and 2x allen keys will be providedTrap Fixing Bracket
9Install Step 1 –Remove Front Cover using Pest KeyStep 1 Step 2Step 3
10Install Step 3 –Align Infra Red Sensors Lenses to the openings in the trapInfra red sensor lenses align with the traps on the RHS as shown above for Tin Cat.NB: For Little Pete there is only one alignment option.Victor Tin Cat JT Eaton Tin Cat
11Install Step 4 –Bolt Sensor to trapPosition LED Lenses to Trap Holes as shown above.Take the Trap Fixing Bracket and Orientate as shown above. Place the Trap Fixing Bracket over the LED Lenses and hold together for bolting (see next page).JT Eaton Tin CatVictor Tin Cat
12Install Step 4 –Bolt Sensor to trapBolts FittedTighten bolts using allen key provided or any suitable 8mm allen key.Please note that the above bolt configuration is for Victor Tin Cat.Use the other set of holes for bolting the JT Eaton Tin Cat. Tighten bolts & ensure sensor is securely fitted to the trap. The Sensor should be parallel to trap as shown left.Second BoltFirst Bolt
13Install Step 5 –Fit Rubber BungsFit the two supplied rubber bungs to the sensor using the allen key supplied. This is required to close and seal the two unused holes to prevent water ingress (mandatory).Please note that this bolt configuration is for Victor Tin Cat.Use the other set of holes for rubber bungs sealing the JT Eaton Tin Cat. Push the bung firmly down to fully insert as shown. The top of the rubber bung must be level or sub flush to the top surface in both positions.
14Install Step 6 –Fit Label to TrapFit the supplied black label inside the Victor/JT Eaton at the opposite end of the trap from the sensor (mandatory).Peel back the release liner to reveal the adhesive and adhere accordingly.Please note that this configuration (Picture left) is Victor Tin Cat.Identical required for JT Eaton Tin Cat. Ensure that the are two holes open.
15Install Step 7 –Fit Rubber Sealing Boot.Orientate and Push Fit the supplied Black Rubber Sealing Boot to the Sensor in position shown left (mandatory).
16Install Step 8 –Install BatteriesNote 1: Only use suitable AA Alkaline BatteriesNote 2: The trap lid MUST BE CLOSED during the battery installation to avoid false triggers during the final setup stage, pictures for reference only.
17Install Step 9 –Replace the CoverRight hand side first, ensuring clip is engagedSNAP!
18Fitment to Little PeteTo fit the MMT sensor to a Little Pete trap.Follow all of the previous steps (identical hole configuration to JT Eaton Tin Cat).Ensure label is flat and smooth when finished.Align label with top edge of entrance housing
19Connect Setup Sequence (1/2)(Read all steps through before starting)Upon initial Power Up the two LED’S go into a Red Level Crossing Effect.Open Trap and break the infra red sensor beams.
20Connect Setup Sequence (2/2)(Read all steps through before starting)Close Lid LED’s now flash Red/Blue untilconnected to the control panel atwhich point 5 blue flashes willindicate a successful connection.Connection can take upto 2minutesdepending on the number ofrepeaters installed, wait until the “5blue flashes” are seenTrap is now connected and ready to be placed in situ and left.
21Technician Service Mode (1/2) Place pest key over the magnet target area for a few seconds and then remove and watch for blue LEDs (Level Crossing Effect).
22Technician Service Mode (2/2) 2 x Blue LED’s flash every 3 seconds indicating it is now ok to open the lid of the trap to service. Servicing can commence.To rearm the trap swipe the magnet again and repeat the ‘Connect Setup Sequence’ by testing the IR’s and confirming the system has reconnected to the Control Panel.
23LED’s & TroubleshootingLED Sensor State Detail ActionSingle Solid Red During Power on Battery Level Low Replace BatteryRed Level Crossing LEDDuring Power on Trap awaiting sensor test Open Lid and break the infra red beams with handRed & Blue Flashing LEDSetup Attempting connection to Control PanelPlease wait5 x Blue LED FlashesSetup /Connection to Control PanelSensor has successfully connected to the Control PanelNo action required5 x Red LED FlashesSetup / Connection to Control PanelSensor has been unable to connect to the Control Panel.Reduce the distance from sensor to Control Panel or install a repeater.Single flashing blue LEDSetup One set of Infra Red sensors has been tested, awaiting test of other set.Replace hand in trap and swipe left to right, place hand closer to sensor. Replace sensor if fault persistsSolid Green LEDSetup Infra Red Sensors have not been triggered within 30 secondsBegin setup again. Replace sensor if unable to clear fault.Rapid Flashing Green LEDSetup One set of IR’s has passed, one set has failed and 30 seconds has elapsedBegin setup again. Replace sensor if unable to clear fault2 x Solid Blue LED’sMag swipe Sensor entering service mode Wait 3 seconds for the trap to enter service modeBlue Level Crossing LEDService Mode Trap is in service mode, it is safe to open the trap without sending false trigger alerts to the Control PanelService trapSolid RED LED –Flashing Blue LEDEntering Service ModeLow Battery has been detected Replace battery
Thank you

Navigation menu