Ricoh RFAPL02 Full-Color MFP User Manual 3 of 3

Ricoh Company Ltd Full-Color MFP 3 of 3

Contents

User Manual 3 of 3

=hgg^\mbg`mhma^?ma^kg^mCgm^k_Z\^Nabll^\mbhg]^l\kb[^lahpmh\hgg^\m?ma^kg^mbgm^k_Z\^\Z[e^mhma^?ma^kg^mbgm^k_Z\^(ƯƯC_ma^fZbgihp^klpbm\ablhg&mnkgbmh__(Ư Ol^ma^_heehpbg`?ma^kg^m\Z[e^l(Ư Oglab^e]^]Npblm^]JZbk=Z[e^"ONJ#hkMab^e]^]Npblm^]JZbk=Z[e^"MNJ#Zg]=Zm^`hkrmri^/hkfhk^+( ;_^kkbm^\hk^_hkma^?ma^kg^mbgm^k_Z\^\Z[e^bllniieb^]pbmamablfZ\abg^(GZd^Zehhibgma^\Z[e^Z[hnm/\f",(+bg\a#"+#_khfma^fZ\abg^^g]h_ma^\Z[e^(;mmZ\ama^_^kkbm^\hk^(BBM011S,( GZd^lnk^ma^fZbgihp^klpbm\ah_ma^fZ\abg^blh__(-( =hgg^\mma^?ma^kg^mbgm^k_Z\^\Z[e^mhma^+*<;M?'N)+**<;M?'NRihkm(BHI014S.( =hgg^\mma^hma^k^g]h_ma^?ma^kg^mbgm^k_Z\^\Z[e^mhZg^mphkd\hgg^\mbhg]^ob\^ln\aZlZan[(,(=hgg^\mbg`ma^GZ\abg^022The Ferrite Core of the cable #8 in the test report's 4.2 Comfiguration of tested system is described in the separated manual.The separated manual is supplied when you buy the option, so it is NOT described in the Users manual.
11. Switch the MBU battery jumper switch [A] to “ON” position. Make sure that the MBU board is firmly connected to the FCU. 12. Reinstall the controller box. 13. Attach the handset support bracket and handset bracket to the copier, and then connect the handset cord with the ferrite core to the "TEL" jack if you install the handset to the machine. For details, refer to the "Hand Set Installation" in the Service Manual for the Fax Unit (D393). 14. Attach the ferrite core to the telephone cord. 15. Connect the telephone cord to the "LINE 1" jack. InstallationInstallation-6As for the Ferrite Core of the cable #2 in the test report's 4.2 Comfiguration of tested system, please see 14 of this page of the service manual (installation-6).Because ｔhis cable is professional installation, the service manual is only for service men, and it is not supplied to the users. 
7. Attach the socket of harness [A] (LINE2) and the socket of harness [C] (LINE3) to the modular bracket for SG3. 8. Connect the harness [A] (LINE2) to the first SG3 board ¶ and the harness [C] (LINE3) to the second SG3 board · ( x 4). 9. Attach the modular bracket for SG3 to the controller box ( x 2). 10. Reinstall the controller box. 11. Attach the ferrite core to the telephone cord for single SG3 board installation, or the two ferrite cores to the telephone cords for double-SG3 board installation. 12. Connect the telephone cord to the "LINE 2" jack for single SG3 board installation, or connect the telephone cords to the "LINE2" and "LINE3" jacks for double-SG3 board installation. 13. Connect the power plug to a power outlet and turn on the main power switch. 14. Enter the service mode. Set bit 1 of communication switch 16 to “1” (SP1-104-023). 15. Set bit 3 of communication switch 16 to "1" (SP1-104-023) if you have installed two SG3 boards. 16. Exit the service mode. 17. Turn the main power switch off and on. 18. Print out the system parameter list. Then check that “G3” shows as an option. 19. Set up and program the items required for PSTN-2 communications. InstallationInstallation-13As for the Ferrite Core of the cable #3 and 4 in the test report's 4.2 Comfiguration of tested system, please see 11, 12 of this page of the service manual (installation-13).
6. Install the scanner left cover on the machine. 7. Attach the clamp to the location [E]. 8. Set the handset on the handset bracket. 9. Put the ferrite core [F] on the handset cord as shown. The length [G] must be 90 mm. 10. Clamp the hand set cord. 11. Connect the handset cable to the “TEL” jack at the rear of the machine. InstallationInstallation-16As for the Ferrite Core of the cable #10 in the test report's 4.2 Comfiguration of tested system, please see 15 of this page of the service manual (installation-16).

Navigation menu