Ruckus SmartCell Gateway™ 200 Command Line Interface Reference Guide For RuckOS 3.0 SCG Ruck OS 3 0 Cli Rg 20141203

SCG-200 Command Line Interface Reference Guide for RuckOS 3.0 scg-3-0-cli-rg--20141203

User Manual: Ruckus SCG-200 Command Line Interface Reference Guide for RuckOS 3.0

Open the PDF directly: View PDF .
Page Count: 382

Download
Open PDF In Browser	View PDF

Ruckus Wireless
SmartCell Gateway 200
™

™

Command Line Interface Reference Guide for
RuckOS 3.0

Part Number 800-70675-001 Rev A
Published November 2014
www.ruckuswireless.com

Copyright Notice and Proprietary Information
Copyright 2014. Ruckus Wireless, Inc. All rights reserved.
No part of this documentation may be used, reproduced, transmitted, or translated, in any form or by any means,
electronic, mechanical, manual, optical, or otherwise, without prior written permission of Ruckus Wireless, Inc.
(“Ruckus”), or as expressly provided by under license from Ruckus.

Destination Control Statement
Technical data contained in this publication may be subject to the export control laws of the United States of America.
Disclosure to nationals of other countries contrary to United States law is prohibited. It is the reader’s responsibility to
determine the applicable regulations and to comply with them.

Disclaimer
THIS DOCUMENTATION AND ALL INFORMATION CONTAINED HEREIN (“MATERIAL”) IS PROVIDED FOR GENERAL
INFORMATION PURPOSES ONLY. RUCKUS AND ITS LICENSORS MAKE NO WARRANTY OF ANY KIND, EXPRESS
OR IMPLIED, WITH REGARD TO THE MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY, NON-INFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE, OR THAT THE
MATERIAL IS ERROR-FREE, ACCURATE OR RELIABLE. RUCKUS RESERVES THE RIGHT TO MAKE CHANGES OR
UPDATES TO THE MATERIAL AT ANY TIME.

Limitation of Liability
IN NO EVENT SHALL RUCKUS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, DATA OR USE, INCURRED BY YOU OR ANY
THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT OR TORT, ARISING FROM YOUR ACCESS TO, OR USE
OF, THE MATERIAL.

Trademarks
Ruckus Wireless, Ruckus, the bark logo, ZoneFlex, FlexMaster, ZoneDirector, SmartMesh, Channelfly, Smartcell,
Dynamic PSK, and Simply Better Wireless are trademarks of Ruckus Wireless, Inc. in the United States and other
countries. All other product or company names may be trademarks of their respective owners.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

2

Contents

About This Guide
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1

Introduction to the SCG Command Line Interface
Overview of the SCG Command Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Accessing the Command Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
What You Will Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connect the Administrative Computer to SCG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Start and Configure the SSH Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using SSH Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using Serial Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Log On to CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2

Configuration Commands
config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3rd-zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
acct-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
config-admin-radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
adv-forwarding-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
ap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
ap-auto-tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
ap-cert-check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
ap-control-mgmt-tos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
ap-heartbeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
ap-portal-cert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
ap-root-ca . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
ap-sci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
auth-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
cgf-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
changepassword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

3

Contents

clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
cluster-ip-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
cluster-redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
data-plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
dhcp-service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
do. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
dp-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3

67
67
68
70
72
73
74
75

Configuration Commands
eap-aka . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
eap-sim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
encrypt-mac-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
event db-persistence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
event email . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
event snmp-trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
event-email . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
ftp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
ftp-test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
ggsn-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
hlr-mnc-ndc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
hlr-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
hlr-system-wide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
hostname . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
hotspot-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
ip default-gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
ip internal-subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
ip name-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
ip separate-access-core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
l2ogre-profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
l3ogre-profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
lbs-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
license import . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

4

Contents

lineman . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
logging console. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
lwapp2scg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
mgmt-acl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
mvno . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
network-traffic-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
no 3rd-zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
no acct-profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
no admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
no admin-radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
no adv-forwarding-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
no ap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
no ap auto-tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
no ap-cert-check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
no ap-control-mgmt-tos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
no ap-root-ca . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
no ap-sci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
no auth-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
no cgf-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
no cls-sess msisdn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
no cls-sess . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
no control-plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
no data-plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
no dhcp-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
no domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
no dp-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
no eap-aka . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
no eap-sim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
no encrypt-mac-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
no event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
no ftp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
no ggsn-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
no hlr-mnc-ndc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
no hlr-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
no hotspot-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
no interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
no ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
no l2ogre-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
no l3ogre-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

5

Contents

no lbs-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
no lineman . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
no logging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
no mvno . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
no network-traffic-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
no pmipv6-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
no radius-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
no report. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
no rks-gre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
no role . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
no snmp-trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
no snmp-v2-community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
no snmp-v3-user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
no soft-gre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
no subpackages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
no ttg-pdg-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
no user-agent-blacklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
no user-role . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
no user-traffic-profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
no zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
northbound-authtype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
northbound-portal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
ntp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
pmipv6-profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
q-in-q-ethertype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
radius-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
rks-gre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
role . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213

4

Configuration Commands
sms-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
smtp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
snmp-trap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
snmp-v2-community. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
snmp-v3-user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
soft-gre. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
stats-upload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
subpackages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

6

Contents

syslog-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
ttg-pdg-profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
user-agent-blacklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
user-role . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
user-traffic-profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
web-cert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
zone-template. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
zone-zd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280

5

Debug Commands
debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
ap-cli . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
do. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
execute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
export log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
no screen-pagination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
screen-pagination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288

6

Setup Commands
rbddump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290

7

Show Commands
show 3rd zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
show admin-activity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
show alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
show ap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
show ap-stats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
show backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
show backup-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
show backup-config-state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
show backup-network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
show backup-state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

7

Contents

show backup-upgrade-state. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
show cgf-cnxn-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
show cgf-tx-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
show client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
show clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
show cls-sess . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
show cls-sess-range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
show cluster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
show cluster-state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
show control-plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
show control-plane-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
show cpuinfo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
show data-plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
show data-plane-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
show dhcp-relay-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
show dhcp-server-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
show diskinfo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
show event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
show ggsn-cnxn-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
show ggsn-gtpc-stats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
show history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
show hlr-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
show hlr-sctp-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
show interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
show internal-subnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
show ip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
show license . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
show lma-connectivity-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
show lma-signaling-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
show meminfo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
show ntp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
show radius-proxy-stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
show radius-server-stats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
show report-result. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
show rogue-aps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
show running-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334
show service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348
show ttg-client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
show upgrade-history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

8

Contents

show upgrade-state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
show version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
show zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351

8

System Commands
? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354
backup config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
backup network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
backup-upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
cluster in-service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
copy backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
copy backup-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
copy backup-network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
copy client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
copy report-result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
delete backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
delete backup-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
delete backup-network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362
delete client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362
diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363
enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365
enable  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365
exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
no service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
reload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
reload ap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
reload data-plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
reload now . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
remote ap-cli . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
restore config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
restore local . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372
restore network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
service restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

9

Contents

service start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374
set-factory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376
shutdown now . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376
upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377

Index

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

10

About This Guide
This SmartCell Gateway™ (SCG) 200 Command Line Interface Reference Guide
contains the syntaxes and commands for configuring and managing the SCG from
the command line interface.
This guide is written for service operators and system administrators who are
responsible for managing, configuring, and troubleshooting Ruckus Wireless
devices. Consequently, it assumes a basic working knowledge of local area
networks, wireless networking, and wireless devices.
NOTE: This guide assumes that the SmartCell Gateway has already been installed
as described in Getting Started Guide.
Most user guides and release notes are available in Adobe Acrobat Reader Portable
Document Format (PDF) or HTML on the Ruckus Wireless Support Web site at
https://support.ruckuswireless.com/documents.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

11

About This Guide
Document Conventions

Document Conventions
Table 1 and Table 2 list the text and notice conventions that are used throughout
this guide.
Table 1.

Text conventions

Convention

Description

monospace

Represents information as it [Device name]>
appears on screen

monospace bold

Represents information that [Device name]> set
you enter
ipaddr 10.0.0.12

default font bold

Keyboard keys, software
buttons, and field names

On the Start menu, click All
Programs.

italics

Screen or page names

Click Advanced Settings.
The Advanced Settings page
appears.

Table 2.

Example

Notice conventions

Notice Type

Description

NOTE

Information that describes important features or instructions

CAUTION!

Information that alerts you to potential loss of data or potential
damage to an application, system, or device

WARNING!

Information that alerts you to potential personal injury

Related Documentation
For a complete list of documents that accompany this release, refer to the Release
Notes.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

12

About This Guide
Documentation Feedback

Documentation Feedback
Ruckus Wireless is interested in improving its documentation and welcomes your
comments and suggestions. You can email your comments to Ruckus Wireless at:
docs@ruckuswireless.com
When contacting us, please include the following information:
• Document title
• Document part number (on the cover page)
• Page number (if appropriate)
For example:
• Ruckus Wireless SmartCell Gateway 200 Administrator Guide (Release 3.0)
• Part number: 800-70672-001
• Page 88

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

13

Introduction to the SCG Command
Line Interface

1

In this chapter:
• Overview of the SCG Command Line Interface
• Accessing the Command Line Interface

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

14

Introduction to the SCG Command Line Interface
Overview of the SCG Command Line Interface

Overview of the SCG Command Line Interface
The SCG command line interface (CLI) is a software tool that enables you to
configure and manage SmartCell Gateway 200. Using the command line interface,
you can issue commands from an operating system prompt, such as the Microsoft
Windows command prompt or a Linux operating system terminal. Each command
performs a specific action for configuring device settings or returning information
about the status of a specific device feature.

Accessing the Command Line Interface
The SCG-200 has a built-in command line interface (CLI) that you can use to
configure SCG settings and manage access points. This section describes the
requirements and the procedure for accessing the SCG CLI.

What You Will Need
To access the SCG CLI, you will need the following:
1 A computer that you want to designate as administrative computer
2 A network connection to SCG (if you want to use an SSH connection) or an RS232 serial to RJ45 cable (if you want to use a serial connection)
3 An SSH (secure shell) client

Connect the Administrative Computer to SCG
Connect the administrative computer to SCG either through the network or directly
using an RS-232 serial to RJ45 cable.
1 If you want to use an SSH connection, connect the administrative computer to
the same subnet or broadcast domain as the Management (Web) interface of
the SCG.
2 If you want to use a serial connection, make sure that both the administrative
computer and the SCG are both powered on. And then, do the following:
• Connect the RJ45 end of the cable to the port labeled |O|O| (console port)
on the SCG. See Figure 1 for the location of the console port.
• Connect the RS-232 end of the cable to a COM port on the administrative
computer.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

15

Introduction to the SCG Command Line Interface
Accessing the Command Line Interface

Figure 1. Location of console port

Start and Configure the SSH Client
Before starting this procedure, make sure that the SSH client is already installed on
the administrative computer.
NOTE: The following procedure describes how to use PuTTY, a free and open
source telnet/SSH client, to access the SCG CLI. If you are using a different SSH
client, the procedure may be slightly different (although the connection settings
should be the same). For more information on PuTTY, visit www.putty.org.
See the following sections depending on your connection method:
• Using SSH Connection
• Using Serial Connection

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

16

Introduction to the SCG Command Line Interface
Accessing the Command Line Interface

Using SSH Connection
If you have connected the administrative computer to the same subnet or broadcast
domain as the Management (Web) interface of the SCG, follow these steps to start
and configure the SSH client.
1 Start PuTTY. The PuTTY configuration dialog box appears, showing the Session
screen as seen in Figure 2.
2 In Connection type, select SSH.
Figure 2. Selecting SSH as a connection type

3 Enter the IP address of the Management (Web) interface of the SCG in the Host
Name (or IP address) field as seen in Figure 2.
4 Click Open. The PuTTY console appears and displays the login prompt. See
Figure 6.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

17

Introduction to the SCG Command Line Interface
Accessing the Command Line Interface

Using Serial Connection
If you have connected the administrative computer to the console port on the SCG
using an RS-232 serial to RJ45 cable, follow these steps to start and configure the
SSH client.
1 Start PuTTY. The PuTTY Configuration dialog box appears, showing the Session
screen as seen in Figure 3.
2 In Connection type, select Serial if you are connecting via serial cable.
Figure 3. Selecting serial as a connection type

3 Under Category, click Connection > Serial. The serial connection options appear
on the right side of the dialog box, displaying PuTTY’s default serial connection
settings. See Figure 4.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

18

Introduction to the SCG Command Line Interface
Accessing the Command Line Interface

Figure 4. PuTTy’s default serial connection setting

4 Configure the serial connection settings as follows. See Figure 5.
• Serial line to connect to: Type the COM port name to which you connected
the RS-232 cable.
• Bits per second: 115200
• Data bits: 8
• Stop bits: 1
• Parity: None
• Flow control: None

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

19

Introduction to the SCG Command Line Interface
Accessing the Command Line Interface

Figure 5. PuTTY’s serial connection settings for connecting to SCG

5 Click Open. The PuTTY console appears and displays the login prompt as seen
in Figure 6.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

20

Introduction to the SCG Command Line Interface
Accessing the Command Line Interface

Figure 6. PuTTY console displaying the login prompt

You have completed configuring the SSH client to connect to the SCG CLI.

Log On to CLI
The following describes the process for logging on to the CLI.
• Log on to the SCG using putty/Xssh (any other application) using the user
credentials of login name and password as given.
NOTE: You cannot use 'admin' as a password, which is used during the SCG
installation procedure.
• The Ruckus Wireless SCG CLI welcome message appears with the CLI prompt
as seen in Figure 7.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

21

Introduction to the SCG Command Line Interface
Accessing the Command Line Interface

Figure 7. Welcome to SCG

• You are now logged into the SCG CLI as a user with limited privileges by looking
at the CLI prompt. If you are in limited mode, the prompt appears as ruckus>
(with a greater than sign). To view a list of commands that are available at the
root level or user mode, enter help or ? as seen in Figure 7 and Figure 8.
NOTE: To change the CLI prompt to a privileged mode, see step 5.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

22

Introduction to the SCG Command Line Interface
Accessing the Command Line Interface

Figure 8. Using Show Commands

• As a user with limited privileges, you can view a history of commands that were
previously executed and ping a device as seen in Figure 9.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

23

Introduction to the SCG Command Line Interface
Accessing the Command Line Interface

Figure 9. Using the Ping command

• If you want to run more commands, you need to switch to privileged mode by
entering enable and the password at the root prompt as seen in Figure 10. The
prompt changes from ruckus> to ruckus# (with a pound sign) as seen in Figure
10. Refer to enable command for details.
Figure 10. Changing to privileged mode

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

24

2

Configuration Commands

This chapter describes the commands that you can use to configure, enable, and
disable various SCG components. The following table lists the commands.
NOTE: For easy access and reading, the configuration chapter has been split into
three chapters based on the alphabetical order of commands.
Table 3.

Configuration commands

3rd-zone

acct-profile

admin

ap

ap-autotagging

ap-cert-check ap-controlmgmt-tos

ap-heartbeat

ap-portal-cert

ap-root-ca

ap-sci

auth-profile

cgf-service

changepasswor clock
d

cluster-ip-list

clusterredundancy

data-plane

dhcp-service

dp-group

domain

do

config-admin- adv-forwardingradius
profile

config
To execute commands in configuration mode, you need to change the mode to:
ruckus(config)#
Example
SCG30# config
SCG30(config)#

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

25

Configuration Commands
3rd-zone

3rd-zone
To create or update the third party AP zone configuration, use the following
command.
ruckus(config)# 3rd-zone 
Syntax Description
This command uses the following syntax:
name: AP zone name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# 3rd-zone indus-ap

Related Commands
Table 4 lists the related to 3rd-zone configuration commands.
Table 4.

Commands related to ruckus(config-3rd-zone).

Syntax and Type

Parameters (if any)

Description

ruckus(config-3rd-zone)# accessnetwork

[qinq-l2 | l2ogre]

Sets the access network to Qin-Q layer 2 or L2oGRE.

Type: Privileged
ruckus(config-3rd-zone)# acct-interval : Interval to
send interim update
Type: Privileged

Sets the accounting interval.

ruckus(config-3rd-zone)# acct-server
Type: Privileged

Sets the accounting service.

ruckus(config-3rd-zone)# acctservice-profile



Sets the accounting service
profile.



Sets the accounting for TTG
session.

Type: Privileged
ruckus(config-3rd-zone)# acct-ttgsession
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

26

Configuration Commands
3rd-zone

Table 4.

Commands related to ruckus(config-3rd-zone).

Syntax and Type

Parameters (if any)

ruckus(config-3rd-zone)# auth-server
Type: Privileged
ruckus(config-3rd-zone)# authservice-profile

Description
Sets the authentication
service.



Sets the authentication service
profile.

Type: Privileged
ruckus(config-3rd-zone)# auth-type

Sets the authentication service
type.

Type: Privileged
ruckus(config-3rd-zone)# corenetwork

Sets the core network.

Type: Privileged
ruckus(config-3rd-zone)# description



Sets the description,

Type: Privileged
ruckus(config-3rd-zone)# do

Executes the do command.

Type: Privileged
ruckus(config-3rd-zone)# end
Type: Privileged

Ends the current configuration
session and returns to
privileged EXEC mode.

ruckus(config-3rd-zone)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-3rd-zone)# forwarding- 
service-profile

Sets the core network
forwarding profile.

Type: Privileged
ruckus(config-3rd-zone)# help

Displays the help.

Type: Privileged
ruckus(config-3rd-zone)# hotspotprofile



Sets the hotspot (WISPr)
service profile.

ruckus(config-3rd-zone)# ip

single-ip 

Type: Privileged

ip-range  

Sets the access network
source IP address.

Type: Privileged

subnet  

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

27

Configuration Commands
3rd-zone

Table 4.

Commands related to ruckus(config-3rd-zone).

Syntax and Type

Parameters (if any)

Description

ruckus(config-3rd-zone)# move

domain 

Moves the zone to another
domain.



Sets the 3rd party zone name.



Sets the access network traffic
profile.

ruckus(config-3rd-zone)# no

acct-server

Type: Privileged

acct-service-profile

Disables and deletes
commands.

Type: Privileged
ruckus(config-3rd-zone)# name
Type: Privileged
ruckus(config-3rd-zone)# networktraffic-profile
Type: Privileged

acct-ttg-session
ip
radius-client
vlan-tag
ruckus(config-3rd-zone)# radius-client default-share-secret

Type: Privileged

Sets the RADIUS client
options.

single-ip 

ip-range  

subnet  

ruckus(config-3rd-zone)# vlan-tag
Type: Privileged

s-vlan   c-vlan  
s-vlan   c-vlan   vlanmapping 


SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

28

Configuration Commands
acct-profile

Table 4.

Commands related to ruckus(config-3rd-zone).

Syntax and Type

Parameters (if any)

Description

ruckus(config-3rd-zone)# vlan-type

qinq

Type: Privileged

strip-qinq

Sets the core network VLAN
mapping type.

strip-svlan-preservecvlan
strip-qinq-add-vlan

map-svlan-preservecvlan
qinq 
strip-all
preserve-all
strip-all-add-vlan 

acct-profile
To create or update the accounting service profile configuration, use the following
command:
ruckus(config)# acct-profile 
Syntax Description
This command uses the following syntax:
name: Accounting service profile name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# acct-profile rad-profile

Related Commands
• Table 5 lists the related acct-profile configuration commands.
• Table 6 lists the related acct-profile-realm configuration commands.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

29

Configuration Commands
acct-profile

Table 5 lists the related acct-profile configuration commands.
Table 5.

Commands related to ruckus(config-acct-profile).

Syntax and Type

Parameters (if any)

Description

ruckus(config-acct-profile)# default

no-match-realm acct


Set the default service.

no-realm acct 

No matching or no realm found
based on the default accounting
service and accounting service
name.



Set the description.

Type: Privileged

ruckus(config-acct-profile)#
description
Type: Privileged
ruckus(config-acct-profile)# do

Executes the do command.

Type: Privileged
ruckus(config-acct-profile)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-acct-profile)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-acct-profile)# help

Displays the help.

Type: Privileged
ruckus(config-acct-profile)# name



Sets the accounting service
profile name.

realm 

Disables the realm based on the
realm name.



Set the accounting service
realm.

Type: Privileged
ruckus(config-acct-profile)# no
Type: Privileged
ruckus(config-acct-profile)# realm
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

30

Configuration Commands
admin

Table 6 lists the related acct-profile-realm configuration commands.
.

Table 6.

Commands related to ruckus(config-acct-profile-realm)

Syntax and Type

Parameters (if any)

ruckus(config-acct-profile-realm)# acct-service 

Description
Sets the accounting service.

Type: Privileged
ruckus(config-acct-profile-realm)# do

Executes the do command.

Type: Privileged
ruckus(config-acct-profile-realm)# end
Type: Privileged

Ends the current
configuration session and
returns to privileged EXEC
mode.

ruckus(config-acct-profile-realm# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-acct-profile-realm)# help

Displays the help.

Type: Privileged
ruckus(config-acct-profile-realm)# name



Sets the realm name.

Type: Privileged

admin
To create or update the administrator’s profile (including the email address, login ID
and password), use the following command:
ruckus(config)# admin 
Once you enter the config-admin context, you can configure the rest of the
administrator’s profile (see example below).
Syntax Description
This command uses the following syntax:
name: Administrator user name
Default
This command has no default settings.
Command Mode
Config

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

31

Configuration Commands
admin

Example
ruckus(config)# admin joe
ruckus(config-admin)# email joe@company.com
ruckus(config-admin)# password admin!234
ruckus(config-admin)# phone 22870001
ruckus(config-admin)# real-name "Joe Admin"
ruckus(config-admin)# title CTO
ruckus(config-admin)# radius radius-1
ruckus(config-admin-radius)# ip 1.1.1.1
ruckus(config-admin-radius)# port 1813
ruckus(config-admin-radius)# realm tw1
ruckus(config-admin-radius)# shared-secret 11
Retype: **
ruckus(config-admin-radius)# exit
ruckus(config-admin)# exit
ruckus(config)#

Related Commands
Table 7 lists the related admin configuration commands.
Table 7.

Commands related to ruckus(config-admin)

Syntax and Type

Parameters (if any)

ruckus(config-admin)# do

Description
Executes the do command.

Type: Privileged
ruckus(config-admin)# email



Set the user’s email details.

Type: Privileged
ruckus(config-admin)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-admin)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-admin)# help

Displays the help.

Type: Privileged
ruckus(config-admin)# password



Set the password for user.



Set the phone number of the
user.

Type: Privileged
ruckus(config-admin)# phone
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

32

Configuration Commands
config-admin-radius

Table 7.

Commands related to ruckus(config-admin)

Syntax and Type

Parameters (if any)

Description

ruckus(config-admin)# real-name



Set the real name of the user.



Set the user’s job title.

Type: Privileged
ruckus(config-admin)# title
Type: Privileged

config-admin-radius
To configure the RADIUS server for administrators use the following command:
ruckus(config)# admin-radius
Syntax Description
This command uses the following syntax:
name: RADIUS server name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# admin-radius aaa-auth

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

33

Configuration Commands
config-admin-radius

Related Commands
Table 8 lists the related admin-radius-service configuration commands.
Table 8.

Commands related to ruckus(config-radius-service)

Syntax and Type

Parameters (if any)

ruckus(config-admin-radius)# do

Description
Executes the do command.

Type: Privileged
ruckus(config-admin-radius)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-admin-radius)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-admin-radius)# help

Displays the help.

Type: Privileged
ruckus(config-admin-radius)# ip



Sets the IP addresses of the
primary RADIUS server.

ruckus(config-admin-radius)# name
Type: Privileged



Sets the RADIUS server name.

ruckus(config-admin-radius)# port



Sets the port addresses of the
primary RADIUS server.

Type: Privileged

Type: Privileged
ruckus(config-admin-radius)# realm
Type: Privileged

ruckus(config-admin-radius)# service
Type: Privileged

ruckus(config-admin-radius)# sharedsecret
Type: Privileged

Sets the realms.
 Multiple
realms supported.
Use a comma (,) to
separate realms
(example:home1,hom
e2)
: Multiple Sets the services.
services supported.
Use a comma (,) to
separate services
(example:home1,hom
e2)

Shared secret
between 1 and 255.

Sets the shared secret of the
primary RADIUS server.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

34

Configuration Commands
adv-forwarding-profile

Table 8.

Commands related to ruckus(config-radius-service)

Syntax and Type

Parameters (if any)

Description

ruckus(config-admin-radius)# test
Type: Privileged




Tests the RADIUS server based
on the user credentials.

ruckus(config-admin-radius)# type

[ radius | tacacs ]]

Sets the admin authentication
type,

Type: Privileged

adv-forwarding-profile
To enter the advanced (mixed mode) profile configuration, use the following
command:
ruckus(config)# adv-forwarding-profile 
Syntax Description
This command uses the following syntax:
name: Profile name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# adv-forwarding-profile ttg-pdg

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

35

Configuration Commands
adv-forwarding-profile

Related Commands
• Table 9 lists related adv-forwarding-profile configuration commands.
• Table 10 lists the related adv-forwarding-profile-apn configuration commands.
Table 9 lists commands related to adv-forwarding-profile configuration commands.
Table 9.

Commands related to ruckus(config-adv-forwarding-profile)

Syntax and Type

Parameters (if any)

Description

ruckus(config-adv-forwardingprofile)# apn

nioi 

Creates or updates the
forwarding policy for APN
configuration commands.

ni 

Type: Privileged
ruckus(config-adv-forwardingprofile)# default

Sets the APN default settings.

Type: Privileged
ruckus(config-adv-forwardingprofile)# description



Sets the description. Length is
between 1 and 128.

apn 

Delete forwarding policies for
APN or default APNs for realm.

Type: Privileged
ruckus(config-adv-forwardingprofile)# no

realm 

Type: User
ruckus(config-adv-forwardingprofile)# realm

Creates or updates the default
APN for realm.

Type: Privileged
ruckus(config-adv-forwardingprofile)# do

Executes the do command.

Type: Privileged
ruckus(config-adv-forwardingprofile)# end
Type: Privileged
ruckus(config-adv-forwardingprofile)# exit

Ends the current configuration
session and returns to privileged
EXEC mode.
Exits from the EXEC.

Type: Privileged
ruckus(config-adv-forwardingprofile)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

36

Configuration Commands
adv-forwarding-profile

Table 10 lists the related adv-forwarding-profile-apn configuration commands.
Table 10.

Commands related to ruckus(config-adv-forwarding-profile-apn)

Syntax and Type

Parameters (if any)

ruckus(config-adv-forwarding-profileapn)# profile

Description
Sets the forwarding service
profile.

Type: Privileged
ruckus(config-adv-forwarding-profileapn)# route-type

[ bridge | l3ogre ]

Sets the route type to either
bridge or L3oGRE.

Type: Privileged
ruckus(config-adv-forwarding-profileapn)# do

Executes the do command.

Type: Privileged
ruckus(config-adv-forwarding-profileapn)# end
Type: Privileged
ruckus(config-adv-forwarding-profileapn)# exit

Ends the current configuration
session and returns to privileged
EXEC mode.
Exits from the EXEC.

Type: Privileged
ruckus(config-adv-forwarding-profileapn)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

37

Configuration Commands
ap

ap
To update the AP configuration, use the following commands:
ruckus(config)# ap 
ruckus(config)# ap pre-prov > >
ruckus(config)# ap swap > >
Syntax Description
This command uses the following syntax:
 lock
: AP MAC address
lock: Lock AP
 ap pre-prov > >
: AP MAC address
pre-prov: Update Pre-provision configuration
: Import the pre-provision APs from a CSV file using FTP
: FTP URL, format: ftp://:@/
export: Exports the pre-provision APs to a CSV file using FTP
 ap swap > >
: AP MAC address
swap: Update Swap configuration
: Imports the pre-provision APs from a CSV file using FTP
: FTP URL, format: ftp://:@/
export: Exports the pre-provision APs to a CSV file using FTP
 move zone 
: AP MAC address
move: Move AP
zone: Target AP Zone
: AP Zone name
Default
This command has no default settings.
Command Mode
Config

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

38

Configuration Commands
ap

Example
ruckus(config)# ap mac
SCG30(config)# ap A1:87:45:34:56:FE
ruckus(config)# ap pre-prov >
SCG30(config)# ap pre-prov import ftp://
ruckus:ruckus1!@172.19.7.100/backup/AP_ad8745345
ruckus(config)# ap swap >
SCG30(config)# ap swap export ftp://ruckus:ruckus1!@172.19.7.100

Related Commands
• Table 11 lists the related ap profile configuration commands.
• Table 12 lists the related ap model configuration commands.
• Table 13 lists the related ap model lan1 configuration commands.
Table 11 lists the related ap profile configuration commands.
Table 11. Commands related to ruckus(config-ap).
Syntax and Type

Parameters (if any)

ruckus(config-ap)# admin

  Sets the administrative logon
credentials.

Type: Privileged

Description

ruckus(config-ap)# admin-mode   Sets the administrative mode to either
locked or unlocked.
Type: Privileged
ruckus(config-ap)# ap-logon



Sets the access point administration
login credentials.



Sets the model specification (overrides
the zone configuration).

Type: Privileged
ruckus(config-ap)# ap-model
Type: Privileged
ruckus(config-ap)# ap-password 
Type: Privileged
ruckus(config-ap)# bonjourgateway

Sets the access point administrative
password.
Enables the bonjour gateway.

Type: Privileged
ruckus(config-ap)# bonjourpolicy

Enables the bonjour policy.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

39

Configuration Commands
ap

Table 11. Commands related to ruckus(config-ap).
Syntax and Type

Parameters (if any)

Description

ruckus(config-ap)# clientadmission-control

2.4g

Enables the client admission control.

Type: Privileged

2.4g minClientCount


5g

Min Client Count
(Default: 10)
2.4g maxRadioLoad

Max Radio Load
(Default: 75%)
2.4g
minClientThroughput
:
Min Client Throughput
(Default: 0.0Mbps)
5g minClientCount

Min Client Count
(Default: 20)
5g maxRadioLoad

Max Radio Load
(Default: 75%)
5g
minClientThroughput

Min Client Throughput
(Default: 0.0Mbps)
ruckus(config-ap)# description
Type: Privileged
ruckus(config-ap)# gps
Type: Privileged



Sets the model specification (overrides
the zone configuration).

  Sets the GPS coordinates to latitude
and longitude values.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

40

Configuration Commands
ap

Table 11. Commands related to ruckus(config-ap).
Syntax and Type

Parameters (if any)

Description

ruckus(config-ap)# gps-latitude



Sets the GPS coordination latitude.



Sets the GPS coordination longitude.

Type: Privileged
ruckus(config-ap)# gpslongitude
Type: Privileged
ruckus(config-ap)# do

Executes the do command.

Type: Privileged
ruckus(config-ap)# end
Type: Privileged

Ends the current configuration session
and returns to privileged EXEC mode.

ruckus(config-ap)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-ap)# help

Displays the help.

Type: Privileged
ruckus(config-ap)# hotspot20
Type: Privileged

 [ swe | cze | Sets the hotspot 2.0 settings.
spa | eng | chi | ger | fre
| jpn | dan | tur | dut ]
: Name
swe: Swedish
cze: Czech
spa: Spanish
eng: English
chi: Chinese
ger: German
fre: French
jpn: Japanese
dan: Danish
tur: Turkish
dut: Dutch

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

41

Configuration Commands
ap

Table 11. Commands related to ruckus(config-ap).
Syntax and Type

Parameters (if any)

Description

ruckus(config-ap)# ip

address 



Sets the IP address and primary and
secondary DNS servers.

Type: Privileged

name-server  secondary
ruckus(config-ap)# location



Sets the location.

Type: Privileged
ruckus(config-ap)# mesh
Type: Privileged

[ root | disable | auto | Sets the mesh mode to either:
mesh ]
• root: Root AP
• disable: Disable
• auto: Auto
• mesh: Mesh AP

ruckus(config-ap)# model

Sets the model specifications. It
overrides the zone configuration.

Type: Privileged
ruckus(config-ap)# name



Sets the AP name.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

42

Configuration Commands
ap

Table 11. Commands related to ruckus(config-ap).
Syntax and Type

Parameters (if any)

Description

ruckus(config-ap)# no

admin

Disables the configuration.

Type: Privileged

bonjour-gateway
client-admissioncontrol
description
hotspot20
ip 
 
location
model
override-clientadmission-control
override-smart-mon
radio
smart-mon
swap-in-ap
syslog
uplink-ap

ruckus(config-ap)# overrideclient-admission-control

<2.4g> <5g>

Overrides the client admission control.

Type: Privileged
ruckus(config-ap)# overridesmart-mon

Overrides the smart monitor.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

43

Configuration Commands
ap

Table 11. Commands related to ruckus(config-ap).
Syntax and Type

Parameters (if any)

Description

ruckus(config-ap)# radio

2.4g channel


Sets the radio channels.

Type: Privileged

5g channel 
2.4g channelization

5g channelization

2.4g tx-power 
5g tx-power 
2.4g wlan-service
5g wlan-service
2.4g wlan-group

5g wlan-group

2.4g roam [ enable |
disable ]
5g roam [ enable |
disable ]
ruckus(config-ap)# smart-mon
Type: Privileged

interval 

Enables the smart monitor.

threshold 
ruckus(config-ap)# swap-in-ap
Type: Privileged



Sets the AP Mac IP address for swapin.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

44

Configuration Commands
ap

Table 11. Commands related to ruckus(config-ap).
Syntax and Type

Parameters (if any)

Description

ruckus(config-ap)# syslog

enable   Enable the syslog
server

Sets the syslog server.

Type: Privileged

enable   [
Local2 | Keep Original |
Local1 | Local5 | Local6
| Local0 | Local7 |
Local3 | Local4 ] [ Error |
Critical | Warning | All |
Alert | Notice | Info |
Emergency ]
disable - Disables the
syslog server
ruckus(config-ap)# uplink

[ smart | manual ]

Type: Privileged

Sets the uplink selection to either smart
or manual.

ruckus(config-ap)# uplink-ap

Sets the uplink to manual access point.

Type: Privileged
ruckus(config-ap)# zone



Move the access point to another zone.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

45

Configuration Commands
ap

Table 12 lists the related to ap-model configuration commands.
Table 12. Commands related to ruckus(config-ap-model)
Syntax and Type

Parameters (if any)

ruckus(config-ap-model)# ext-ant 2.4g  - 2.4
with DBI number
Type: Privileged

Description
Enables the external antenna.

2.4gg  [ 3 | 2
] - 3/2 antennas
5g  - 5g with
DBI number
5gg  [ 2 | 3 ]
- 5gg with 2/3
antennas
ruckus(config-ap-model)#
internal-heater

Enables the internal heater.

Type: Privileged
ruckus(config-ap-model)# lan1

Sets the LAN configurations from 1 to
5.

ruckus(config-ap-model)# lan2
ruckus(config-ap-model)# lan3
ruckus(config-ap-model)# lan4
ruckus(config-ap-model)# lan5
Type: Privileged
ruckus(config-ap-model)# led

Enables the status of LEDs.

Type: Privileged
ruckus(config-ap-model)# ledmode

Sets the LED mode.

Type: Privileged
ruckus(config-ap-model)# lldp

Enables link layer discovery protocol.

Type: Privileged
ruckus(config-ap-model)# lldpad-interval



Sets the LLDP advertise interval.



Sets the LLDP hold time.

Type: Privileged
ruckus(config-ap-model)# lldphold-time
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

46

Configuration Commands
ap

Table 12. Commands related to ruckus(config-ap-model)
Syntax and Type

Parameters (if any)

ruckus(config-ap-model)# lldpmgmt

Description
Enables LLDP management IP TLV.

Type: Privileged
ruckus(config-ap-model)# no

ext-ant

Type: Privileged

internal-heater

Disables or deletes the settings that
have been configured.

lan1
lan2
lan3
lan4
lan5
led
lldp
lldp-mgmt
poe-out-port
radio-band
ruckus(config-ap-model)# poeout-port

Enables the PoE out port.

Type: Privileged
ruckus(config-ap-model)# radioband

${value}

Switches the radio band.

Type: Privileged
ruckus(config-ap-model)# do

Executes the do command.

Type: Privileged
ruckus(config-ap-model)# end
Type: Privileged

Ends the current configuration session
and returns to privileged EXEC mode.

ruckus(config-ap-model)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-ap-model)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

47

Configuration Commands
ap

Table 13 lists the related to ap-model-lan1 configuration commands.
Table 13. Commands related to ruckus(config-ap-model-lan1)
Syntax and Type

Parameters (if any)

Description

ruckus(config-ap-model-lan1)#
8021x

<802.1x-type>

Sets 802.1x.



Sets the authentication service
configurations.



Sets the authentication service
configurations.

Type: Privileged
ruckus(config-ap-model-lan1)#
acct-service
Type: Privileged
ruckus(config-ap-model-lan1)#
auth-service
Type: Privileged
ruckus(config-ap-model-lan1)#
mac-bypass

Sets the MAC bypass.

Type: Privileged
ruckus(config-ap-model-lan1)#
members



Sets the AP model configurations.

Type: Privileged
ruckus(config-ap-model-lan1)# no acct-service
Type: User

mac-bypass

Disables or deletes the settings that
have been configured.

ruckus(config-ap-model-lan1)#
supplicant

mac

Sets the supplicant.

Type: Privileged

custom 


ruckus(config-ap-model-lan1)#
type

[trunk-port | access- Sets the port type.
port | general-port]

Type: Privileged
ruckus(config-ap-model-lan1)#
vlan-untag-id



Sets the VLAN untag IID.

Type: Privileged
ruckus(config-ap-model-lan1)# do

Executes the do command.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

48

Configuration Commands
ap-auto-tagging

Table 13. Commands related to ruckus(config-ap-model-lan1)
Syntax and Type

Parameters (if any)

ruckus(config-ap-model-lan1)#
end

Description
Ends the current configuration session
and returns to privileged EXEC mode.

Type: Privileged
ruckus(config-ap-model-lan1)#
exit

Exits from the EXEC.

Type: Privileged
ruckus(config-ap-model-lan1)#
help

Displays the help.

Type: Privileged

ap-auto-tagging
To setup critical access point auto tagging rules or to enable auto tagging critical
access points, use the following command:
ruckus(config)# ap-auto-tagging 
ruckus(config)# ap-auto-tagging rule  [ g | m ]>>
Syntax Description
This command uses the following syntax:
enable: Enable the auto tagging critical APs
rule: Select the auto tagging rule
daily-threshold: Daily traffic bytes that exceeds the threshold rule
g: Threshold value in gigabytes
m: Threshold value in megabytes
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# ap-auto-tagging enable
SCG30(config)# ap-auto-tagging rule daily-threshold 90 g

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

49

Configuration Commands
ap-auto-tagging

Related Commands
Table 14 lists the related to ap-auto-tagging configuration commands.
Table 14. Commands related to ruckus(config-ap-auto-tagging)
Syntax and Type

Parameters (if any)

ruckus(config-ap-auto-tagging)#
enable

Description
Enables the auto tagging for critical
APs.

Type: Privileged
ruckus(config-ap-auto-tagging)#
no



Disables the auto tagging for critical
APs.



Sets the auto tagging rule to daily traffic
bytes, which exceeds the threshold
rule.



Sets the threshold value.

[m|g]

Sets the unit to either megabytes or
gigabytes.

Type: Privileged
ruckus(config-ap-auto-tagging)#
rule
Type: Privileged
ruckus(config-ap-auto-tagging)#
threshold
Type: Privileged
ruckus(config-ap-auto-tagging)#
unit
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

50

Configuration Commands
ap-cert-check

ap-cert-check
To enable the access point certificate check, use the following command:
ruckus(config)# ap-cert-check
Syntax Description
This command has no arguments or keywords.
Default
This command has the default settings of enable.
Command Mode
Config
Example
SCG30(config)# ap-cert-check
Successful operation

ap-control-mgmt-tos
To enable the access control and management traffic type of service and values,
use the following command:
ruckus(config)# ap-control-mgmt-tos 
Syntax Description
This command has no arguments or keywords.
Default
This command uses the following syntax:
value: TOS value
Command Mode
Config
Example
SCG30(config)# ap-control-mgmt-tos 10

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

51

Configuration Commands
ap-heartbeat

ap-heartbeat
To setup the access point heartbeat, use the following command:
ruckus(config)# ap-heartbeat 
Syntax Description
This command uses the following syntax:
seconds: Interval in seconds, which the AP sends the heartbeat to the SCG such
as: 30, 60, 150 and 300
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# ap-heartbeat 30

ap-portal-cert
To update the AP portal certificate configuration, use the following command:
ruckus(config)# ap-portal-cert
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30SCG30(config)# ap-portal-cert

Related Commands
• Table 15 lists the related to ap-portal-cert configuration commands.
• Table 16 lists the related to ap-portal-cert-generate-csr configuration
commands.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

52

Configuration Commands
ap-portal-cert

Table 15 lists the related to ap-portal-cert configuration commands.
Table 15. Commands related to ruckus(config-ap-portal-cert)
Syntax and Type

Parameters (if any)

ruckus(config-ap-portal-cert)#
generate-csr



Type: Privileged

ruckus(config-ap-portal-cert)#
upload-cert
Type: Privileged

ruckus(config-ap-portal-cert)# do

Description

Generates the certificate signing
FTP URL, format: ftp:/ request.
:@[/
]


Uploads the certificate.

FTP URL, format: ftp:/
:@[/
]
Executes the do command.

Type: Privileged
ruckus(config-ap-portal-cert)# end
Type: Privileged

Ends the current configuration session
and returns to privileged EXEC mode.

ruckus(config-ap-portal-cert)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-ap-portal-cert)#
help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

53

Configuration Commands
ap-portal-cert

Table 16 lists the related to ap-portal-cert-generate-csr configuration commands.
Table 16. Commands related to ruckus(config-ap-portal-cert-generate-csr)
Syntax and Type

Parameters (if any)

Description

ruckus(config-ap-portal-certgenerate-csr)# city



Sets the city name.



Sets the domain name.



Sets the county.



Sets the email address.



Sets the organization name.



Sets the state name.



Sets the unit name.

Type: Privileged
ruckus(config-ap-portal-certgenerate-csr)# common-name
Type: Privileged
ruckus(config-ap-portal-certgenerate-csr)# country
Type: Privileged
ruckus(config-ap-portal-certgenerate-csr)# email
Type: Privileged
ruckus(config-ap-portal-certgenerate-csr)# organization
Type: Privileged
ruckus(config-ap-portal-certgenerate-csr)# state
Type: Privileged
ruckus(config-ap-portal-certgenerate-csr)# unit
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

54

Configuration Commands
ap-root-ca

ap-root-ca
To update the AP root CA, use the following command:
ruckus(config)# ap-root-ca 
Syntax Description
This command uses the following syntax:
ftp-url: AP Root CA file, FTP URL Format: ftp://:@/
)
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# ap-root-ca ftp://mahan:ruckus1!@172.19.7.100/
backup/AP_ad87453456fe.csv

ap-sci
To enable the access point sci, use the following command:
ruckus(config)# ap-sci enable
Syntax Description
This command uses the following syntax:
enable: Enables the AP SCI.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# ap-sci enable

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

55

Configuration Commands
auth-profile

auth-profile
To enter authentication service profile configuration, use the following command:
ruckus(config)# auth-profile 
Syntax Description
This command uses the following syntax:
name: Authentication service profile name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# auth-profile aaa-auth

Related Commands
• Table 17 lists the related auth profile configuration commands.
• Table 18 lists the related auth profile realm configuration commands.
Table 17 lists the related auth-profile configuration commands.
Table 17. Commands related to ruckus(config-auth-profile)
Syntax and Type

Parameters (if any)

Description

ruckus(config-auth-profile)# aaainterim-acct-interval



Sets the interim accounting
interval for hosted AAA server.



Set the session idle timeout for
hosted AAA server.



Set the session timeout for hosted
AAA server

Type: Privileged
ruckus(config-auth-profile)# aaasession-idle-timeout
Type: Privileged
ruckus(config-auth-profile)# aaasession-timeout
Type: Privileged
ruckus(config-auth-profile)# aaasupport

Enables hosted AAA support.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

56

Configuration Commands
auth-profile

Table 17. Commands related to ruckus(config-auth-profile)
Syntax and Type

Parameters (if any)

ruckus(config-auth-profile)# default

Description
Sets default services.

Type: Privileged
ruckus(config-auth-profile)#
description



Sets the descriptions.

Type: Privileged
ruckus(config-auth-profile)# do

Executes the do command.

Type: Privileged
ruckus(config-auth-profile)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-auth-profile)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-auth-profile)# help

Displays the help.

Type: Privileged
ruckus(config-auth-profile)# gppsupport

Enables 3GPP support.

Type: Privileged
ruckus(config-auth-profile)# no

gpp-support

Type: Privileged

aaa-support

Disables GPP, AAA or Realm
support.

realm 
ruckus(config-auth-profile)# realm



Sets the realm.



Sets the mobile country code.



Sets the mobile network code.

Type: Privileged
ruckus(config-auth-profile)# sgsnmcc
Type: Privileged
ruckus(config-auth-profile)# sgsnmnc
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

57

Configuration Commands
auth-profile

Table 18 lists the related auth-profile-realm configuration commands.
Table 18. Commands related to ruckus(config-auth-profile-realm)
Syntax and Type

Parameters (if any)

ruckus(config-auth-profile-realm)#
auth-method

Description
Sets the authorization method.

Type: Privileged
ruckus(config-auth-profile-realm)#
auth-service



Sets the authentication service.



Sets the dynamic VLAN ID.

Type: Privileged
ruckus(config-auth-profile-realm)#
dynamic-vlan
Type: Privileged
ruckus(config-auth-profile-realm# do

Executes the do command.

Type: Privileged
ruckus(config-auth-profile-realm)#
end
Type: Privileged
ruckus(config-auth-profile-realm)#
exit

Ends the current configuration
session and returns to privileged
EXEC mode.
Exits from the EXEC.

Type: Privileged
ruckus(config-auth-profile-realm)#
help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

58

Configuration Commands
cgf-service

cgf-service
To setup the CGF service configuration, use the following command:
ruckus(config)# cgf-service 
Syntax Description
This command uses the following syntax:
name: CGF service name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# cgf-service charge-ser

Related Commands
• Table 19 lists the related cgf service profile configuration commands.
• Table 20 lists the related cgf service ftp server configuration commands.
• Table 21 lists the related cgf service server configuration commands.
Table 19 lists the related cgf-service profile configuration commands.
Table 19. Commands related to ruckus(config-cgf-service) profile
Syntax and Type

Parameters (if any)

ruckus(config-cgf-service)# autoexport-ftp

Description
Enables the auto export through
FTP.

Type: Privileged
ruckus(config-cgf-service)# cdrnode-id



Enables the node ID. The length
range is between 1 and 20.



Sets the CDR response timeout.

Type: Privileged
ruckus(config-cgf-service)# cdrresponse-timeout
Type: Privileged
ruckus(config-cgf-service)# cdr-retry 

Sets the CDR retries.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

59

Configuration Commands
cgf-service

Table 19. Commands related to ruckus(config-cgf-service) profile
Syntax and Type
ruckus(config-cgf-service)# cdrsend-apn-network-id

Parameters (if any)

Description
Enables in sending the APN
network identifier to the CDR.

Type: Privileged
ruckus(config-cgf-service)# cdrsend-apn-op-id

Enables sending the APN
operator identifier.

Type: Privileged
ruckus(config-cgf-service)# cdrsend-apn-sel-mode

Enables sending the APN
selection mode.

Type: Privileged
ruckus(config-cgf-service)# cdrsend-charging-sel-mode

Enables sending the charging
characteristic selection mode.

Type: Privileged
ruckus(config-cgf-service)# cdrsend-diag

Enables sending the diagnostic
to the CDR.

Type: Privileged
ruckus(config-cgf-service)# cdrsend-dyn-addr-flag

Enables in sending the dynamic
mode address flag.

Type: Privileged
ruckus(config-cgf-service)# cdrsend-local-record-sn

Enables in sending the local
record sequence number.

Type: Privileged
ruckus(config-cgf-service)# cdrsend-msisdn

Enables in sending the MSISDN.

Type: Privileged
ruckus(config-cgf-service)# cdrsend-node-id

Enables in sending the node ID
to the CDR.

Type: Privileged
ruckus(config-cgf-service)# cdrsend-pdp-addr

Enables in sending the PDF
address to the CDR.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

60

Configuration Commands
cgf-service

Table 19. Commands related to ruckus(config-cgf-service) profile
Syntax and Type

Parameters (if any)

ruckus(config-cgf-service)# cdrsend-pdp-type

Description
Enables in sending the PDF type
to the CDR.

Type: Privileged
ruckus(config-cgf-service)# cdrsend-rat-type

Enables in sending the RAT type.

Type: Privileged
ruckus(config-cgf-service)# cdrsend-sgsn-addr

Enables in sending the SGSN
address to the CDR.

Type: Privileged
ruckus(config-cgf-service)# cdrsgsn-plmn-id

Enables the SGSN/WAG PLMN
identifier

Type: Privileged
ruckus(config-cgf-service)# cdrtraffic-vol

Enables listing traffic volumes.

Type: Privileged
ruckus(config-cgf-service)# cdr-ttg

Sets the CDR for TTG.

Type: Privileged
ruckus(config-cgf-service)# cdr-type [s-cdr | w-cdr]
Type: Privileged

Sets the CDR type as S-CDR or
W-CDR.

ruckus(config-cgf-service)#
charging-mode

[ local-binary-file | server | Sets the charging service type.
both ]

Type: Privileged

local-binary-file: Local
Binary File
server: Server
both: Both

ruckus(config-cgf-service)#
description



Sets the CGF service
description.

Type: Privileged
ruckus(config-cgf-service)# do

Executes the do command.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

61

Configuration Commands
cgf-service

Table 19. Commands related to ruckus(config-cgf-service) profile
Syntax and Type

Parameters (if any)

ruckus(config-cgf-service)# end

Description

Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-cgf-service)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-cgf-service)# help

Displays the help.

Type: Privileged
ruckus(config-cgf-service)# exportschedule

daily  
hour 

Sets the export schedule based
on hours and minutes or daily.



Sets the file lifetime.

Type: Privileged
ruckus(config-cgf-service)# file-lifetime
Type: Privileged
ruckus(config-cgf-service)# file-time- 
limit

Sets the file timer interval.

Type: Privileged
ruckus(config-cgf-service)# ftpserver



Sets the FTP server setting by
defining the host server.

Type: Privileged
ruckus(config-cgf-service)# ftpserver-test

Tests the FTP settings.

Type: Privileged
ruckus(config-cgf-service)# gtpecho-retry



Set the retries of GTP echo
response.



Sets the retries of GTP echo
timeout.

Type: Privileged
ruckus(config-cgf-service)# gtpecho-timeout
Type: Privileged
ruckus(config-cgf-service)# lbo
Type: Privileged

Enables CDR for direct IP access
(LBO).

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

62

Configuration Commands
cgf-service

Table 19. Commands related to ruckus(config-cgf-service) profile
Syntax and Type

Parameters (if any)

Description

ruckus(config-cgf-service)# lbonode-id



Enables the node ID. The length
range is between 1 and 20.

Type: Privileged
ruckus(config-cgf-service)# lbosend-local-record-sn

Enables in sending the local
record sequence number.

Type: Privileged
ruckus(config-cgf-service)# lbosend-node-id

Enables the node identifier.

Type: Privileged
ruckus(config-cgf-service)# max-cdr- 
request

Sets the maximum CDRs per
request.

Type: Privileged
ruckus(config-cgf-service)# no

auto-export-ftp

Type: Privileged

cdr-send-apn-network-id

Disable various options.

cdr-send-apn-sel-mode
cdr-send-apn-op-id
cdr-send-charging-selmode
cdr-send-diag
cdr-send-dyn-addr-flag
cdr-send-local-record-sn
cdr-send-msisdn
cdr-send-node-id
cdr-send-pdp-addr
cdr-send-pdp-type
cdr-send-rat-type

.................................continued

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

63

Configuration Commands
cgf-service

Table 19. Commands related to ruckus(config-cgf-service) profile
Syntax and Type

Parameters (if any)

Description

ruckus(config-cgf-service)# no

cdr-send-sgsn-addr

Disables various options.

Type: Privileged

cdr-sgsn-plmn-id
cdr-traffic-vol
cdr-ttg
lbo
lbo-send-local-record-sn
lbo-send-node-id
server 

ruckus(config-cgf-service)# recordlimit



Sets the record limit.

ruckus(config-cgf-service)# server

 priority [up | down]

Type: Privileged



Sets the server’s IP address. The
DNS server’s priority can also be
changed by moving the priority
either up or down.

Type: Privileged

Table 20 lists the related cgf-service-ftp-server configuration commands.
Table 20. Commands related to ruckus(config-cgf-service-ftp-server)
Syntax and Type

Parameters (if any)

Description

ruckus(config-cgf-service-ftpserver)# password



Sets the username for the FTP
server.



Sets the FTP server port.



Sets the remote directory for the
FTP server.

Type: Privileged
ruckus(config-cgf-service-ftpserver)# port
Type: Privileged
ruckus(config-cgf-service-ftpserver)# remote-dir
Type: Privileged
ruckus(config-cgf-service-ftpserver)# test

Tests the FTP settings.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

64

Configuration Commands
cgf-service

Table 20. Commands related to ruckus(config-cgf-service-ftp-server)
Syntax and Type

Parameters (if any)

Description

ruckus(config-cgf-service-ftpserver)# username



Sets the username for the FTP
server.

Type: Privileged
ruckus(config-cgf-service-ftpserver)# do

Executes the do command.

Type: Privileged
ruckus(config-cgf-service-ftpserver))# end

Ends the current configuration
session and returns to privileged
EXEC mode.

Type: Privileged
ruckus(config-cgf-service-ftpserver)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-cgf-service-ftpserver)# help

Displays the help.

Type: Privileged

Table 21 lists the related cgf-service-server configuration commands.
Table 21. Commands related to ruckus(config-cgf-service-server)
Syntax and Type

Parameters (if any)

Description

ruckus(config-cgf-service-server)#
port



Sets the server port.

Type: Privileged
ruckus(config-cgf-service-server)#
do

Executes the do command.

Type: Privileged
ruckus(config-cgf-service-server)#
end
Type: Privileged
ruckus(config-cgf-service-server)#
exit

Ends the current configuration
session and returns to privileged
EXEC mode.
Exits from the EXEC.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

65

Configuration Commands
changepassword

Table 21. Commands related to ruckus(config-cgf-service-server)
Syntax and Type

Parameters (if any)

ruckus(config-cgf-service-server)#
help

Description
Displays the help.

Type: Privileged

changepassword
To change the administrative password, use the following command:
ruckus(config)# changepassword  
Syntax Description
This command uses the following syntax:
old password: Existing password
new password: Changed password.
The password must contain at least eight characters with at least one number,
one letter, and one special character (~ ! @ # $ % ^ & * ( ) - _ = + [ ] { } \ | ; : ' "
, . < > / ?) except ` or $(.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# changepassword
Old Password: ruckus1!
New Password:ruckus2!

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

66

Configuration Commands
clock

clock
To update the system clock or the timezone configuration, use the following
command:
ruckus(config)# clock timezone 
Syntax Description
This command uses the following syntax:
timezone: Sets the system clock timezone
: Timezone name of the domain
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# clock timezone Africa/Nairobi

cluster-ip-list
To update the node IP address mapping list of the cluster configuration, use the
following command:
ruckus(config)# cluster-ip-list 
Syntax Description
This command uses the following syntax:
ip-mappings: Node IP mapping list, which is space separated.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# cluster-ip-list : :

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

67

Configuration Commands
cluster-redundancy

SCG30(config)# cluster-ip-list 172.19.18.96:172.19.13.56
172.19.15.67:172.19.10.07

cluster-redundancy
To create or update a cluster redundancy configuration, use the following
command:
ruckus(config)# cluster-redundancy
Syntax Description
This command has no arguments or keywords
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# cluster-redundancy

Related Commands
• Table 22 lists the related cluster redundancy configuration commands.
• Table 23 lists the related cluster redundancy cluster configuration commands.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

68

Configuration Commands
cluster-redundancy

Table 22 lists the related cluster redundancy configuration commands.
Table 22. Commands related to ruckus(config-cluster-redundancy)
Syntax and Type

Parameters (if any)

Description

ruckus(config-cluster-redundancy)#
cluster



Create or update the cluster
redundancy configuration.

Type: Privileged

 priority [ up |
down ]

ruckus(config-cluster-redundancy)# do

Executes the do command.

Type: Privileged
ruckus(config-cluster-redundancy)#
enable

Enables the cluster
redundancy configuration.

Type: Privileged
ruckus(config-cluster-redundancy)# end
Type: Privileged

Ends the current configuration
session and returns to
privileged EXEC mode.

ruckus(config-cluster-redundancy)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-cluster-redundancy)# help

Displays the help.

Type: Privileged
ruckus(config-cluster-redundancy)# no
Type: Privileged



Disables the enable option.



Table 23 lists the related cluster redundancy cluster configuration commands.
Table 23. Commands related to ruckus(config-cluster-redundancy-cluster)
Syntax and Type

Parameters (if any)

Description

ruckus(config-cluster-redundancycluster)# ip-list



Sets the control IP address
list.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

69

Configuration Commands
data-plane

data-plane
To update the dataplane configuration, use the following command:
ruckus(config)# data-plane  < forward-stp>
Syntax Description
This command uses the following syntax:
: Name of the dataplane
forward-stp: Disables the STP package bridge
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# data-plane indus4d1

Related Commands
Table 24 lists the related data plane configuration commands
Table 24. Commands related to ruckus(config-data-plane)
Syntax and Type

Parameters (if any)

Description

ruckus(config-data-plane)# ip

route 



Sets the IP configuration
commands.

Type: Privileged

address dhcp
address  

secondary 

name-server 
secondary
route   

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

70

Configuration Commands
data-plane

Table 24. Commands related to ruckus(config-data-plane)
Syntax and Type

Parameters (if any)

Description

ruckus(config-data-plane)# no

ip secondary

Disables / deletes options.

Type: Privileged

ip name-server
secondary
ip route 


ip route  

vlan

ruckus(config-data-plane)# do

Executes the do command.

Type: Privileged
ruckus(config-data-plane)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-data-plane)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-data-plane)# help

Displays the help.

Type: Privileged
ruckus(config-data-plane)# vlan

 secondary

Updates the VLAN configuration.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

71

Configuration Commands
dhcp-service

dhcp-service
To setup the DHCP service configuration, use the following command.
ruckus(config)# dhcp-service 
Syntax Description
This command uses the following syntax:
name: HCP service name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# dhcp-service dhcp1

Related Commands
Table 25 lists the related dhcp service profile configuration commands.
Table 25. Commands related to ruckus(config-dhcp-service)
Syntax and Type

Parameters (if any)

Description

ruckus(config-dhcp-service)#
description



Sets the description.

server secondary

Disables the secondary DHCP
server.

 [secondary |
primary]

Sets the IP address for DHCP
secondary and primary servers.

Type: Privileged
ruckus(config-dhcp-service)# no
Type: Privileged
ruckus(config-dhcp-service)# server
Type: Privileged
ruckus(config-dhcp-service)# do

Executes the do command.

Type: Privileged
ruckus(config-dhcp-service)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-dhcp-service)# exit

Exits from the EXEC.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

72

Configuration Commands
do

Table 25. Commands related to ruckus(config-dhcp-service)
Syntax and Type

Parameters (if any)

ruckus(config-dhcp-service)# help

Description
Displays the help.

Type: Privileged

do
To setup the do command, use the following command.
ruckus(config)# do
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# do

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

73

Configuration Commands
dp-group

dp-group
To enable and set the dataplane grouping, use the following command.
ruckus(config)# dp-group 
Syntax Description
This command uses the following syntax:
: Dataplane groups, which is comma separated DP MAC
addresses in a group. For example, 3 DP value is seen as “,”.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# dp-group dp1-172.19.7.100 dp2-172.19.8.120

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

74

Configuration Commands
domain

domain
To create or update the domain configuration, use the following command:
ruckus(config)# domain 
Syntax Description
This command uses the following syntax:
name: Name of the domain
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# domain indusap1

Related Commands
• Table 26lists the related to domain configuration commands.
• Table 27 lists the related domain 3rd-zone configuration commands.
• Table 28 lists the related domain-zone configuration commands.
• Table 29 lists the related domain-zone-aaa configuration commands.
• Table 30 lists the related domain-zone-ap-group configuration commands.
• Table 31 lists the related domain-zone-ap-group-lldp configuration commands.
• Table 32 lists the related to domain-zone-ap-model configuration commands.
• Table 33 lists the related domain-zone-ap-model-lan1 configuration commands.
• Table 34 lists the related domain-zone-ap-registration-rule configuration
commands.
• Table 35 lists the related domain-zone-bonjour-policy configuration commands.
• Table 37 lists the related domain-zone-device-policy configuration commands.
• Table 38 lists the related domain-zone-device-policy policy rule configuration
commands.
• Table 39 lists the related zone-guest-access configuration commands.
• Table 40 lists the related domain-zone-hotspot configuration commands.
• Table 41 lists the related domain-zone-l2-acl configuration commands.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

75

Configuration Commands
domain

• Table 42 lists the related domain-zone-web-authentication configuration
commands.
• Table 43 lists the related domain-zone-wlan configuration commands.
• Table 44 lists the related domain-zone-wlan-group configuration commands.
• Table 45 lists the related domain-zone-wlan-scheduler configuration commands.
Table 26 lists the related to domain configuration commands.
Table 26. Commands related to ruckus(config-domain)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain)# 3rd-zone



Creates or updates a Third Party
AP zone in the current domain.

Type: Privileged




Adds an administrator and
assign a role in the current
domain.

ruckus(config-domain)# description



Sets the domain description.

Type: Privileged
ruckus(config-domain)# admin

Type: Privileged
ruckus(config-domain)# do

Executes the do command.

Type: Privileged
ruckus(config-domain)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-domain)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-domain)# help

Displays the help.

Type: Privileged
ruckus(config-domain-)# no

admin 

Type: Privileged

zone 

Disable or remove configuration
settings in the current domain,

ruckus(config-domain)# parent



Sets the parent domain name.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

76

Configuration Commands
domain

Table 26. Commands related to ruckus(config-domain)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain)# zone

 - AP zone
name

Create or update an AP zone in
the current domain.

Type: Privileged

 template
 - Create from
template
 clone 
- Clone from an existing
AP zone
 ap-firmware
 Change AP firmware
 clusterswitch-over  Enable cluster
switchover
ruckus(config-domain)# zone-zd
Type: Privileged

 import


Create AP zone from ZD backup
file.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

77

Configuration Commands
domain

Table 27 lists the related domain 3rd-zone configuration commands.
Table 27. Commands related to ruckus(config-domain-3rd-zone)
Syntax and Type

Parameters (if any)

ruckus(config-domain-3rd-zone)#
acct-interval

 Number of Sets the accounting interval.
minutes to send interim
updates.

Type: Privileged
ruckus(config-domain-3rd-zone)#
acct-server

Description

Sets the accounting service.

Type: Privileged
ruckus(config-domain-3rd-zone)#
acct-service-profile



Sets the accounting service profile
configuration.

Type: Privileged
ruckus(config-domain-3rd-zone)#
acct-ttg-session

Enables accounting for TTG
sessions.

Type: Privileged
ruckus(config-domain-3rd-zone)#
auth-server

Sets the authentication service.

Type: Privileged
ruckus(config-domain-3rd-zone)#
auth-service-profile



Sets the authentication service
profile configuration.

Type: Privileged
ruckus(config-domain-3rd-zone)#
auth-type

Sets the authentication server
type.

Type: Privileged
ruckus(config-domain-3rd-zone)#
core-network

Sets the core network.

Type: Privileged
ruckus(config-domain-3rd-zone)#
description



Sets the description.



Sets the core network forwarding
service profile.

Type: Privileged
ruckus(config-domain-3rd-zone)#
forwarding-service-profile
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

78

Configuration Commands
domain

Table 27. Commands related to ruckus(config-domain-3rd-zone)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-3rd-zone)#
hotspot-profile



Sets the hotspot profile
configuration.

Type: Privileged
ruckus(config-domain-3rd-zone)# ip single-ip 
Type: Privileged

ip-range  

Adds access network source IP
address.

subnet  
ruckus(config-domain-3rd-zone)#
move

domain 

Moves the zone to another
domain.



Sets the network traffic profile.

Type: Privileged
ruckus(config-domain-3rd-zone)#
network-traffic-profile
Type: Privileged
ruckus(config-domain-3rd-zone)# no acct-server
Type: Privileged

acct-service-profile

Disables and deletes configuration
options.

acct-ttg-session
ip
radius-client
vlan-tag
ruckus(config-domain-3rd-zone)#
radius-client

default-share-secret


Type: Privileged

single-ip 


Sets the configuration for RADIUS
client.

ip-range  

subnet  


SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

79

Configuration Commands
domain

Table 27. Commands related to ruckus(config-domain-3rd-zone)
Syntax and Type

Parameters (if any)

ruckus(config-domain-3rd-zone)#
vlan-tag

Adds access network Q-in-Q
s-vlan 
VLAN tags.
 c-vlan
 

Type: Privileged

Description

s-vlan 
 c-vlan
  vlan-mapping


ruckus(config-domain-3rd-zone)#
vlan-type

qinq

Type: Privileged

strip-svlan-preservecvlan

strip-qinq

Sets the core network VLAN
mapping type.

strip-qinq-add-vlan

map-svlan-preservecvlan
add-svlan-preservecvlan 
strip-all
preserve-all
strip-all-add-vlan

ruckus(config-domain-3rd-zone)# do

Executes the do command.

Type: Privileged
ruckus(config-domain-3rd-zone)#
end
Type: Privileged
ruckus(config-domain-3rd-zone)#
exit

Ends the current configuration
session and returns to privileged
EXEC mode.
Exits from the EXEC.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

80

Configuration Commands
domain

Table 27. Commands related to ruckus(config-domain-3rd-zone)
Syntax and Type

Parameters (if any)

ruckus(config-domain-3rd-zone)#
help

Description
Displays the help.

Type: Privileged

Table 28 lists the related domain-zone configuration commands.
Table 28. Commands related to ruckus(config-domain-zone)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone)# aaa



Creates or updates the AAA
server configuration.

ruckus(config-domain-zone)# adjthreshold

2.4g ${value}

Type: Privileged

Value is minimum = 1
and maximum = 100

Sets the adjacent radio
threshold of the client load
balancing.

ruckus(config-domain-zone)# apfirmware



Type: Privileged
5g ${value}

Sets the AP firmware.

Type: Privileged
ruckus(config-domain-zone)# ap-group 
Type: Privileged
ruckus(config-domain-zone)# ap-logon 
Type: Privileged
ruckus(config-domain-zone)# ap-model 

Creates or updates the AP
group configuration.
Sets the login ID for the AP
administrator.

Type: Privileged

Sets the AP model
configuration.

ruckus(config-domain-zone)# appassword

Sets the password for the AP
administrator.

Type: Privileged
ruckus(config-domain-zone)# apreboot-timeout

default-gateway


Type: Privileged

control-gateway [
 ]

Sets the AP reboot timeout.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

81

Configuration Commands
domain

Table 28. Commands related to ruckus(config-domain-zone)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone)# apregistration-rule



Creates or updates the AP
registration rule configuration.

2.4g 

Sets the background scanning.

Type: Privileged
ruckus(config-domain-zone)#
background-scan

5g 

Type: Privileged
ruckus(config-domain-zone)# bandbalancing

2.4g  2.4g

Type: Privileged

: Percentage of
clients on 2.4G band

Sets the band balance.

2.4G band

ruckus(config-domain-zone)# bonjourgateway

Enables the bonjour gateway.

Type: Privileged
ruckus(config-domain-zone)# bonjourpolicy



Creates or updates the bonjour
policy.

ruckus(config-domain-zone)# channel

2.4g 

Sets the channel.

Type: Privileged

5g indoor 

Type: Privileged

5g outdoor 
ruckus(config-domain-zone)#
channelization

2.4g [ 20 | 40 ]

Sets the channelization.

5g [ 40 | 20 ]

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

82

Configuration Commands
domain

Table 28. Commands related to ruckus(config-domain-zone)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone)# clientadmission-control

2.4g

Enables the client admission
control.

Type: Privileged

2.4g minClientCount


5g

2.4g maxRadioLoad

2.4g
minClientThroughput
5g minClientCount

5g maxRadioLoad

5g
minClientThroughput

ruckus(config-domain-zone)# countrycode



Sets the country code.



Sets the description,



Sets the devise policy.



Sets the guest access.

Type: Privileged
ruckus(config-domain-zone)#
description
Type: Privileged
ruckus(config-domain-zone)# devicepolicy
Type: Privileged
ruckus(config-domain-zone)# guestaccess
Type: Privileged
ruckus(config-domain-zone)# headroom 2.4g 
Type: Privileged

5g: 5 GHz radio

ruckus(config-domain-zone)# hotspot



Type: Privileged

Sets the headroom (# of clients)
of client load balancing.
Creates or updates the WISPr
hotspot configuration.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

83

Configuration Commands
domain

Table 28. Commands related to ruckus(config-domain-zone)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone)# indoorchannel

Description
Enables the indoor channels.

Type: Privileged
ruckus(config-domain-zone)# l2-acl



Type: Privileged
ruckus(config-domain-zone)# lbs

Sets the layer 2 access control
list.
Enables the location based
service.

Type: Privileged
ruckus(config-domain-zone)# lbsservice

Sets the location based service.

Type: Privileged
ruckus(config-domain-zone)# loadbalancing

2.4g

Sets the client load balancing.

5g

Type: Privileged
ruckus(config-domain-zone)# mesh

Enables mesh networking.

Type: Privileged
ruckus(config-domain-zone)# meshname



Sets the mesh name (ESSID).



Sets the mesh passphrase.

[ dynamic | static ]

Sets the mesh uplink auto
selection to either dynamic or
static link metrics.

domain 

Moves the zone to another
domain.

Type: Privileged
ruckus(config-domain-zone)# meshpassphrase
Type: Privileged
ruckus(config-domain-zone)# meshuplink-selection
Type: Privileged
ruckus(config-domain-zone)# move
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

84

Configuration Commands
domain

Table 28. Commands related to ruckus(config-domain-zone)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone)# no

aaa 

Type: Privileged

ap-group 

Disables and deletes
commands.

ap-registration-rule

background-scan
<2.4g> <5g>
band-balancing
bonjour-gateway
bonjour-policy
client-admissioncontrol <2.4g> <5g>
description
device-policy
guest-access
hotspot 
indoor-channel
l2-acl
lbs
load-balancing
mesh
roam
smart-mon
smart-roamdisconnect-event
syslog-enabled
timezone-dst
web-authentication
wlan 
wlan-group 
wlan-scheduler
ruckus(config-domain-zone)# roam

2.4g

Type: Privileged

5g

Sets the smart roam.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

85

Configuration Commands
domain

Table 28. Commands related to ruckus(config-domain-zone)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone)# rouge-ap- [ disable | enable ] detection
Disables or enables
rogue access points
Type: Privileged

Description
Sets the report rouge access
point.

report-all [ disable |
enable ] - Enables or
disables all rogue
devices
report-only-malicious [
enable | disable ] Enables or disables
only malicious rogue
device types
report-ssid-spoofing [
disable | enable ] Enables or disables
malicious rogue
devices which have
SSID spoofing
report-same-network [
enable | disable ] Enables or disables
malicious rogue
devices which have
same network
report-mac-spoofing [
disable | enable ] Enables or disables
malicious rogue
devices which have
MAC IP address
spoofing
protect-frommalicious [ disable |
enable ] - Enables or
disables the network
from malicious rogue
access points

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

86

Configuration Commands
domain

Table 28. Commands related to ruckus(config-domain-zone)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone)# smartmon

interval 

Sets the smart monitor interval.

threshold 

Type: Privileged
ruckus(config-domain-zone)# smartroam-disconnect-event

Enables smart roam disconnect
event.

Type: Privileged
ruckus(config-domain-zone)# syslogenabled

Enables the external syslog
server for APs for the specified
zone.

Type: Privileged
ruckus(config-domain-zone)# syslogfacility
Type: Privileged

[ Local7 | Local1 |
Sets the syslog server facility,
Local6 | Keep Original
| Local0 | Local4 |
Local5 | Local3 |
Local2 ]

ruckus(config-domain-zone)# syslog-ip 
Type: Privileged
ruckus(config-domain-zone)# syslogport



Sets the IP address for the
syslog server.
Sets the port number for the
syslog server.

Type: Privileged
ruckus(config-domain-zone)# syslogpriority
Type: Privileged

[ Alert | Info | Critical | Sets the syslog server priority.
Warning | Notice |
Emergency | All | Error ]

ruckus(config-domain-zone)# timezone System - Follows the Sets the timezone for zone.
SCG time zone setting
Type: Privileged
System [  ]
Select the time zone
from system database
User-defined [  ]
User defined time zone
Time zone
abbreviation (example:
GMT, CST, EST)

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

87

Configuration Commands
domain

Table 28. Commands related to ruckus(config-domain-zone)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone)# timezone- [  ]
dst
 
 
Type: Privileged

Description
Sets the user defined timezone
for daylight savings.

ruckus(config-domain-zone)# timezone- [ ] For example, for GMT offset.
8, -7:45
Type: Privileged
ruckus(config-domain-zone)# tunnelprofile



Sets the AP GRE tunnel profile.

Type: Privileged
ruckus(config-domain-zone)# tunnelencrypt

Sets the tunnel encryption.

Type: Privileged
ruckus(config-domain-zone)# tunneltype

[ gre | gre-udp ]

Sets the tunnel type.

Type: Privileged
ruckus(config-domain-zone)# tx-power 2.4g ${value}
Type: Privileged

Sets the TX power adjustment.

5g ${value}
Value is minimum = 1
and maximum = 100

ruckus(config-domain-zone)# weakbypass

2.4g ${value}

Type: Privileged

Value is minimum = 1
and maximum = 100

ruckus(config-domain-zone)# webauthentication



Sets the web authentication.



Creates or updates the WLAN/
ESSID configuration.



Creates or updates the WLAN
group configuration.

5g ${value}

Sets the weak bypass threshold
of the client load balancing.

Type: Privileged
ruckus(config-domain-zone)# wlan
Type: Privileged
ruckus(config-domain-zone)# wlangroup
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

88

Configuration Commands
domain

Table 28. Commands related to ruckus(config-domain-zone)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone)# wlanscheduler



Creates or updates the WLAN
scheduler configuration.

Type: Privileged
ruckus(config-domain-zone)# do

Executes the do command.

Type: Privileged
ruckus(config-domain-zone)# end
Type: Privileged

Ends the current configuration
session and returns to
privileged EXEC mode.

ruckus(config-domain-zone)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-domain-zone)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

89

Configuration Commands
domain

Table 29 lists the related domain-zone-aaa configuration commands.
Table 29. Commands related ruckus(config-domain-zone-aaa)
Syntax and Type

Parameters (if any)

ruckus(config-domain-aaa)# admindomain

Description
Enables the admin domain
name.

Type: Privileged
ruckus(config-domain-aaa)# admindomain-name



Creates or updates the admin
domain.



Creates or updates the admin
password.

ruckus(config-domain-zone-aaa)#
backup

ip 

Type: Privileged

shared-secret 

Enables backup of RADIUS
support and set related
settings.

ruckus(config-domain-aaa)# basedomain



Type: Privileged
ruckus(config-domain-aaa)# adminpassword
Type: Privileged
port 

Set the base domain.

Type: Privileged
ruckus(config-domain-aaa)# description 

Sets the description.

Type: Privileged
ruckus(config-domain-aaa)# globalcatalog

Enables the global catalog
support.

Type: Privileged
ruckus(config-domain-zone-aaa)# ip



Set IP addresses of primary
RADIUS server.



Sets the key attributes for the
primary RADIUS server.

ruckus(config-domain-zone-aaa)# no

backup

Type: Privileged

global-catalog

Disables or deletes
configuration settings.

Type: Privileged
ruckus(config-domain-zone-aaa)# keyattribute
Type: Privileged

no-response-fail

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

90

Configuration Commands
domain

Table 29. Commands related ruckus(config-domain-zone-aaa)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-aaa)# noresponse-fail

Description
Enables no response fail.

Type: Privileged
ruckus(config-domain-zone-aaa)#
password



Sets the password for the
primary RADIUS server.



Sets the port number of the
primary RADIUS server.



Sets the response window.



Sets the revive interval.



Sets the search filter.



Sets the shared secret of the
primary RADIUS server.




Tests the connectivity of the
AAA server.

[ radius | radius-acct |
LDAP | AD ]

Sets the RADIUS type.



Sets the windows domain
name.



Sets the zombie period.

Type: Privileged
ruckus(config-domain-zone-aaa)# port
Type: Privileged
ruckus(config-domain-zone-aaa)#
response-window
Type: Privileged
ruckus(config-domain-zone-aaa)#
revive-interval
Type: Privileged
ruckus(config-domain-zone-aaa)#
search-filter
Type: Privileged
ruckus(config-domain-zone-aaa)#
shared-secret
Type: Privileged
ruckus(config-domain-zone-aaa)# test
Type: Privileged
ruckus(config-domain-zone-aaa)# type
Type: Privileged
ruckus(config-domain-zone-aaa)#
windows-domain
Type: Privileged
ruckus(config-domain-zone-aaa)#
zombie-period
Type: Privileged
ruckus(config-domain-zone-aaa)# do

Executes the do command.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

91

Configuration Commands
domain

Table 29. Commands related ruckus(config-domain-zone-aaa)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-aaa)# end

Description

Type: Privileged

Ends the current configuration
session and returns to
privileged EXEC mode.

ruckus(config-domain-zone-aaa)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-domain-zone-aaa)# help

Displays the help.

Type: Privileged

Table 30 lists the related domain-zone-ap-group configuration commands.
Table 30. Commands related to ruckus(config-domain-zone-ap-group)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-ap-group)#
channel

2.4g ${value}

Sets the channel.

Type: Privileged

5g outdoor ${value}

ruckus(config-domain-zone-ap-group)#
channelization

2.4g [ 20 | 40 ]

5g indoor ${value}
Sets the channelization.

5g [ 40 | 20 ]

Type: Privileged
ruckus(config-domain-zone-ap-group)#
client-admission-control

2.4g

Type: Privileged

2.4g minClientCount


5g

Enables the client admission
control.

Min Client Count
(Default: 10)
2.4g maxRadioLoad

Max Radio Load
(Default: 75%)
2.4g
minClientThroughput
:
Min Client Throughput
..................continued
(Default: 0.0Mbps)

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

92

Configuration Commands
domain

Table 30. Commands related to ruckus(config-domain-zone-ap-group)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-ap-group)#
client-admission-control

5g minClientCount


Enables the client admission
control.

Type: Privileged

Min Client Count
(Default: 20)
5g maxRadioLoad

Max Radio Load
(Default: 75%)
5g
minClientThroughput

Min Client Throughput
(Default: 0.0Mbps)

ruckus(config-domain-zone-ap-group)#
description



Sets the description.

ruckus(config-domain-zone-ap-group)#
external-antenna

 5g [
disable | enable ]

Sets the external antenna for
specific AP model.

Type: Privileged

 5g gain


Type: Privileged

 5g [ 3antennas | 2-antennas ]
 2.4g gain

 2.4g [
enable | disable ]
 2.4g [ 2antennas | 3-antennas ]
ruckus(config-domain-zone-ap-group)#
internal-heater

 [ enable | Sets the internal heater for
disable ]
specific AP model.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

93

Configuration Commands
domain

Table 30. Commands related to ruckus(config-domain-zone-ap-group)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-ap-group)#
lbs

Description
Enables the location based
service.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
lbs-service

Sets the location based
service.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
led-mode



Sets the LED mode for specific
AP model.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
lldp

 [ enable | Sets the LLDP for a specific AP
disable ]
model.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
member

add 

Sets the AP group member.

move-to  

It adds a new access point to
current AP group.

remove 

The AP Mac address removes
the access point from the
current AP group and moves it
to other AP group.

ruckus(config-domain-zone-ap-group)#
no

channel 2.4g

Disables / deletes the
configuration settings.

Type: Privileged

channel 5g outdoor

Type: Privileged

channel 5g indoor
channelization 2.4g
channelization 5g
client-admissioncontrol
description
external-antenna  5g
external-antenna  2.4g
external-antenna
${model}

..................continued

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

94

Configuration Commands
domain

Table 30. Commands related to ruckus(config-domain-zone-ap-group)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-ap-group)#
no

internal-heater

Disables / deletes the
configuration settings.

Type: Privileged

led-mode

lbs
lldp
override-clientadmission-control
override-lbs
poe-out
port-setting
radio-band
status-leds
tx-power 2.4g
tx-power 5g
wlan-group 2.4g
wlan-group 5g

ruckus(config-domain-zone-ap-group)#
override-client-admission-control

2.4g
5g

Overrides the client admission
control settings.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
override-lbs

Overrides the location based
service to zone settings.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
poe-out

 [ enable | Sets the PoE out port for a
disable ]
specific AP model.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
port-setting



Sets the port settings for
specific AP model.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
radio-band

 [ 2.4g | 5g ] Switches the radio band for a
specific AP model.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

95

Configuration Commands
domain

Table 30. Commands related to ruckus(config-domain-zone-ap-group)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-ap-group)#
status-leds

 [ enable | Sets the status LED for
disable ]
specific AP model.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
tx-power

2.4g ${value}

Type: Privileged

5g ${value}

ruckus(config-domain-zone-ap-group)#
wlan-group

2.4g
5g

Sets the TX power adjustment.

Sets the WLAN group
configurations.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
do

Executes the do command.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
end
Type: Privileged
ruckus(config-domain-zone-ap-group)#
exit

Ends the current configuration
session and returns to
privileged EXEC mode.
Exits from the EXEC.

Type: Privileged
ruckus(config-domain-zone-ap-group)#
help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

96

Configuration Commands
domain

Table 31 lists the related domain-zone-ap-group-lldp configuration commands.
Table 31. Commands related to ruckus(config-domain-zone-ap-group lldp)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-ap-grouplldp)# lldp-ad-interval



Sets the LLDP advertise
interval in seconds from the
range 1 to 300.



Type: Privileged

Sets the LLDP hold time in
seconds from the range 60 to
1200.

ruckus(config-domain-zone-ap-grouplldp)# lldp-mgmt

Enables the LLDP
management IP TLV.

Type: Privileged
ruckus(config-domain-zone-ap-grouplldp)# lldp-hold-time

Type: Privileged

Table 32 lists the related to domain-zone-ap-model configuration commands.
Table 32. Commands related to ruckus(config-domain-zone-ap-model)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-ap-model)#
ext-ant

2.4g 

Sets the external antenna.

Type: Privileged

5g 

2.4gg  [ 3 | 2 ]
5gg  [ 2 | 3 ]

ruckus(config-domain-zone-ap-model)#
internal-heater

Enables international heater.

Type: Privileged
ruckus(config-domain-zone-ap-model)#
lan1

Sets the LAN configurations
from 1 to 5.

ruckus(config-domain-zone-ap-model)#
lan2
ruckus(config-domain-zone-ap-model)#
lan3
ruckus(config-domain-zone-ap-model)#
lan4
ruckus(config-domain-zone-ap-model)#
lan5
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

97

Configuration Commands
domain

Table 32. Commands related to ruckus(config-domain-zone-ap-model)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-ap-model)#
led

Description
Enables the status of led.

Type: Privileged
ruckus(config-domain-zone-ap-model)#
led-mode

Sets the led mode
description

Type: Privileged
ruckus(config-domain-zone-ap-model)#
lldp

Enables the Link Layer
Discovery Protocol (LLDP).

Type: Privileged
ruckus(config-domain-zone-ap-model)#
lldp-ad-interval



Sets the LLDP advertise
interval.



Sets the LLDP hold time.

Type: Privileged
ruckus(config-domain-zone-ap-model)#
lldp-hold-time
Type: Privileged
ruckus(config-domain-zone-ap-model)#
lldp-mgmt

Enables the LLDP
management IP TLV.

Type: Privileged
ruckus(config-domain-zone-ap-model)#
no

ext-ant

Type: Privileged

lan1

internal-heater

Disables or deletes the
settings that have been
configured.

lan2
lan3
lan4
lan5
led
lldp
lldp-mgmt
poe-out-port
radio-band

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

98

Configuration Commands
domain

Table 32. Commands related to ruckus(config-domain-zone-ap-model)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-ap-model)#
poe-out-port

Description
Enables the PoE out port

Type: Privileged
ruckus(config-domain-zone-ap-group)#
radio-band

${value}

Switches the radio band for a
specific AP model.

Type: Privileged
ruckus(config-domain-zone-ap-model)#
do

Executes the do command.

Type: Privileged
ruckus(config-domain-zone-ap-model)#
end

Ends the current
configuration session and
returns to privileged EXEC
mode.

Type: Privileged
ruckus(config-domain-zone-ap-model)#
exit

Exits from the EXEC.

Type: Privileged
ruckus(config-domain-zone-ap-model)#
help

Displays the help.

Type: Privileged

Table 33 lists the related domain-zone-ap-model-lan1 configuration commands.
Table 33. Commands related to ruckus(config-domain-zone-ap-model-lan1)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-ap-modellan1)# 8021x

<8021x-type>

Sets the 802.1x.



Sets the accounting service
configurations.



Sets the authentication
service configurations.

Type: Privileged
ruckus(config-domain-zone-ap-modellan1)# acct-service
Type: Privileged
ruckus(config-domain-zone-ap-modellan1)# auth-service
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

99

Configuration Commands
domain

Table 33. Commands related to ruckus(config-domain-zone-ap-model-lan1)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-ap-modellan1)# mac-bypass

Description
Sets the MAC authentication
bypass.

Type: Privileged
ruckus(config-domain-zone-ap-modellan1)# members



Sets the members.

acct-service
mac-bypass

Disables or deletes the
settings that have been
configured.

mac

Sets the supplicant.

Type: Privileged
ruckus(config-domain-zone-ap-modellan1)# no
Type: Privileged
ruckus(config-domain-zone-ap-modellan1)# supplicant
Type: Privileged

custom 


ruckus(config-domain-zone-ap-modellan1)# type

[ trunk-port | accessport | general-port ]

Sets the port type.



Sets the VLAN untag ID.

Type: Privileged
ruckus(config-domain-zone-ap-modellan1)# vlan-untag-id
Type: Privileged
ruckus(config-domain-zone-ap-modellan1)# do

Executes the do command.

Type: Privileged
ruckus(config-domain-zone-ap-modellan1)# end
Type: Privileged
ruckus(config-domain-zone-ap-modellan1)# exit

Ends the current
configuration session and
returns to privileged EXEC
mode.
Exits from the EXEC.

Type: Privileged
ruckus(config-domain-zone-ap-modellan1)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

100

Configuration Commands
domain

Table 34 lists the related domain-zone-ap-registration-rule configuration
commands.
Table 34. Commands related to ruckus(config-domain-zone-ap-registration-rule)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-apregistration-rule)# description



Sets the description.

Type: Privileged
ruckus(config-domain-zone-apregistration-rule)# gps

  Sets the GPS coordinates.


Type: Privileged
ruckus(config-domain-zone-apregistration-rule)# ip-range

 

Sets the IP address range
from and to IP address.



Sets the provision tags.

 

Sets the subnet IP address
and subnet mask.

[ gps | provision-tag |
ip-range | subnet ]

Sets the rule type.

Type: Privileged
ruckus(config-domain-zone-apregistration-rule)# provision-tag
Type: Privileged
ruckus(config-domain-zone-apregistration-rule)# subnet
Type: Privileged
ruckus(config-domain-zone-apregistration-rule)# type
Type: Privileged
ruckus(config-domain-zone-apregistration-rule)# do

Executes the do command.

Type: Privileged
ruckus(config-domain-zone-apregistration-rule)# end
Type: Privileged
ruckus(config-domain-zone-apregistration-rule)# exit

Ends the current
configuration session and
returns to privileged EXEC
mode.
Exits from the EXEC.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

101

Configuration Commands
domain

Table 34. Commands related to ruckus(config-domain-zone-ap-registration-rule)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-apregistration-rule)# help

Description
Displays the help.

Type: Privileged

Table 35 lists the related domain-zone-bonjour-policy configuration commands.
Table 35. Commands related to ruckus(config-domain-zone-bonjour-policy)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-bonjourpolicy)# description



Sets the description.



Deletes the rules based on
the rule priority.



Sets the bonjour policy set of
rules based on the rule
priority.

Type: Privileged
ruckus(config-domain-zone-bonjourpolicy)# no rule
Type: Privileged
ruckus(config-domain-zone-bonjourpolicy)# rule
Type: Privileged
ruckus(config-domain-zone-bonjourpolicy)# do

Executes the do command.

Type: Privileged
ruckus(config-domain-zone-bonjourpolicy)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-domain-zone-bonjourpolicy)# end
Type: Privileged
ruckus(config-domain-zone-bonjourpolicy)# help

Ends the current
configuration session and
returns to privileged EXEC
mode.
Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

102

Configuration Commands
domain

Table 36 lists the related domain-zone-bonjour-policy-rule configuration commands.
Table 36. Commands related to ruckus(config-domain-zone-bonjour-policy-rule)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-bonjourpolicy-rule)# bridge-service

Description
Sets the bridge service.

Type: Privileged
ruckus(config-domain-zone-bonjourpolicy-rule)# from-vlan



Sets the from VLAN.



Sets the notes.

Type: Privileged
ruckus(config-domain-zone-bonjourpolicy-rule)# notes
Type: Privileged
ruckus(config-domain-zone-bonjourpolicy-rule)# protocol

Sets the bridge service
when it is 'other'.

Type: Privileged
ruckus(config-domain-zone-bonjourpolicy-rule)# to-vlan



Sets the VLAN.

Type: Privileged

Table 37 lists the related domain-zone-device-policy configuration commands.
Table 37. Commands related to ruckus(config-domain-zone-device-policy)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-device-policy)# [ allow | block ]
default-action

Description
Sets the default action to
either allow or block.

Type: Privileged
ruckus(config-domain-zone-device-policy)# 
description

Sets the description.

Type: Privileged
ruckus(config-domain-zone-device-policy# [  ]
no policy-rule

Deletes the device policy
rules.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

103

Configuration Commands
domain

Table 37. Commands related to ruckus(config-domain-zone-device-policy)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-device-policy)#
policy-rule

Description
Sets the device policy.

Type: Privileged
ruckus(config-domain-zone-device-policy)#
do

Executes the do command.

Type: Privileged
ruckus(config-domain-zone-device-policy)#
exit

Exits from the EXEC.

Type: Privileged
ruckus(config-domain-zone-device-policy)#
end

Ends the current
configuration session and
returns to privileged EXEC
mode.

Type: Privileged
ruckus(config-domain-zone-device-policy)#
help

Displays the help.

Type: Privileged

Table 38 lists the related domain-zone-device-policy-policy-rule configuration
commands.
Table 38. Commands related to ruckus (config-domain-zone-device-policy-policy rule)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-device-policypolicy-rule)# action

[ allow | block ]

Sets the default action to
either allow or block.



Sets the description.

[  ]

Sets the downlink rate
limiting.

Type: Privileged
ruckus(config-domain-zone-device-policypolicy-rule)# description
Type: Privileged
ruckus(config-domain-zone-device-policypolicy-rule)# downlink

Rate limiting (mbps)

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

104

Configuration Commands
domain

Table 38. Commands related to ruckus (config-domain-zone-device-policy-policy rule)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-device-policypolicy-rule)# no vlan

Description
Resets the VLAN number.

Type: Privileged
ruckus(config-domain-zone-device-policypolicy-rule)# type

[  ]

Sets the device type.

[  ]

Sets the uplink rate limiting.

Type: Privileged
ruckus(config-domain-zone-device-policypolicy-rule)# uplink

Rate limiting (mbps)

Type: Privileged
ruckus(config-domain-zone-device-policypolicy-rule)# vlan

[  ]]

Sets the VLAN number.

Type: Privileged

Table 39 lists the related zone-guest-access configuration commands.
Table 39. Commands related to ruckus (config-zone-guest-access)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-guest-access)# 
description

Description
Sets the description.

Type: Privileged
ruckus(config-domain-zone-guest-access)#
enable-terms-and-conditions

Enables the web portal
terms and conditions.

Type: Privileged
ruckus(config-domain-zone-guest-access)# 
grace-period

Sets the grace period.

Type: Privileged
ruckus(config-domain-zone-guest-access)#
language

Sets the language.

Type: Privileged
ruckus(config-domain-zone-guest-access)# enable-terms-andno
conditions
Type: Privileged

Disables the various
options.

sms-gateway
terms-and-conditions

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

105

Configuration Commands
domain

Table 39. Commands related to ruckus (config-zone-guest-access)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-guest-access)# 
session-timeout

Description

Type: Privileged

Sets the session timeout
as per the specified
minutes.

ruckus(config-domain-zone-guest-access)#
sms-gateway

Sets the guest pass for
the SMS gateway.

Type: Privileged
ruckus(config-domain-zone-guest-access)# original
start-page
redirect 
Type: Privileged

Sets the start page.

ruckus(config-domain-zone-guest-access)#
terms-and-conditions
Type: Privileged

Sets the terms and
conditions for the web
portal.

ruckus(config-domain-zone-guest-access)#
title

Sets the title for the web
portal.

Type: Privileged

Table 40 lists the related domain-zone-hotspot configuration commands.
Table 40. Commands related to ruckus(config-domain-zone-hotspot)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-hotspot)#
description



Sets the description.



Sets the grace period.



Sets the location ID.



Sets the location name.

Type: Privileged
ruckus(config-domain-zone-hotspot)#
grace-period
Type: Privileged
ruckus(config-domain-zone-hotspot)#
location-id
Type: Privileged
ruckus(config-domain-zone-hotspot)#
location-name
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

106

Configuration Commands
domain

Table 40. Commands related to ruckus(config-domain-zone-hotspot)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-hotspot)#
logon-url

internal

Sets the logon model

external 

Type: Privileged
ruckus(config-domain-zone-hotspot)# no
Type: Privileged
ruckus(config-domain-zone-hotspot)#
session-timeout

walled-garden 
options.


Sets the sessions timeout.

ruckus(config-domain-zone-hotspot)#
smart-client-support

none

Sets the smart client
support.

Type: Privileged

only 

Type: Privileged
enable

ruckus(config-domain-zone-hotspot)# start- original
page
redirect 
Type: Privileged

Sets the start page.

ruckus(config-domain-zone-hotspot)#
walled-garden

Enables Walled Garden.
Allows unauthorized
destinations. Commaseparated IP, IP range,
CIDR and regular
expression domain name
list

Type: Privileged

ruckus(config-domain-zone-hotspot)# do
Type: Privileged
ruckus(config-domain-zone-hotspot)# end



Executes the do
command.

Type: Privileged

Ends the current
configuration session and
returns to privileged EXEC
mode.

ruckus(config-domain-zone-hotspot)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-domain-zone-hotspot)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

107

Configuration Commands
domain

Table 41 lists the related domain-zone-l2-acl configuration commands.
Table 41. Commands related to ruckus(config-domain-zone-l2-acl)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-l2-acl)# action

[ allow | block ]

Sets the handling action to
allow or block.



Sets the description.

${value}

Sets the MAC value.

Type: Privileged
ruckus(config-domain-zone-l2-acl)#
description
Type: Privileged
ruckus(config-domain-zone-l2-acl)# mac
Type: Privileged
ruckus(config-domain-zone-l2-acl)# no mac ${value}

Disables the MAC value.

Type: Privileged

Table 42 lists the related domain-zone-web-authentication configuration
commands.
Table 42. Commands related to ruckus (config-domain-zone-web-authentication)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-webauthentication)# description



Sets the description.



Sets the grace period.

Type: Privileged
ruckus(config-domain-zone-webauthentication)# grace-period
Type: Privileged
ruckus(config-domain-zone-webauthentication)# language

Sets the language.

Type: Privileged
ruckus(config-domain-zone-webauthentication)# session-timeout



Sets the session timeout as
per the specified minutes.

original

Sets the start page.

Type: Privileged
ruckus(config-domain-zone-webauthentication)# start-page

redirect 

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

108

Configuration Commands
domain

Table 43 lists the related domain-zone-wlan configuration commands.
Table 43. Commands related to ruckus(config-domain-zone-wlan)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-wlan)#
access-network

Description
Enables tunnel WLAN traffic to
the SCG.

Type: Privileged
ruckus(config-domain-zone-wlan)#
acct-delay-time

Enables the acct-delay time.

Type: Privileged
ruckus(config-domain-zone-wlan)#
acct-interval



Set the authentication service.
Enables accounting interval to
send interim updates.



Sets the accounting service.

Type: Privileged
ruckus(config-domain-zone-wlan)#
acct-service
Type: Privileged
ruckus(config-domain-zone-wlan)#
acct-service-use-proxy

Set the accounting service:
Uses the SCG as proxy.

Type: Privileged
ruckus(config-domain-zone-wlan)#
acct-ttg-session

Sets the accounting service.
Enables accounting for TTG
sessions.

Type: Privileged
ruckus(config-domain-zone-wlan)#
auth-method

Sets the authentication method.

Type: Privileged
ruckus(config-domain-zone-wlan)#
auth-service



Sets the authentication service.

Type: Privileged
ruckus(config-domain-zone-wlan)#
auth-service-use-proxy
Type: Privileged
ruckus(config-domain-zone-wlan)#
auth-type

Sets the authentication service.
Enables accounting for TTG
sessions.
Sets the authentication type.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

109

Configuration Commands
domain

Table 43. Commands related to ruckus(config-domain-zone-wlan)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-wlan)#
bss-minrate

[ 5.5mbps | 24mbps |
12mbps | 1mbps |
2mbps ]

Sets the BSS minimum rate.

Type: Privileged
ruckus(config-domain-zone-wlan)#
called-sta

Sets the called STA ID.

Type: Privileged
ruckus(config-domain-zone-wlan)#
client-fingerprinting

Sets the client fingerprinting.

Type: Privileged
ruckus(config-domain-zone-wlan)#
client-tx-rx-statistics

Enables ignore statistics from
unauthorized clients.

Type: Privileged
ruckus(config-domain-zone-wlan)#
core-network
Type: Privileged
ruckus(config-domain-zone-wlan)#
description

[ l3ogre | ttg-pdg |
Sets the core network.
bridge | mixed | l2ogre |
pmipv6 ]


Sets the description,

[  ]

Sets the device policy.

Type: Privileged
ruckus(config-domain-zone-wlan)#
device-policy
Type: Privileged
ruckus(config-domain-zone-wlan)#
dgaf

Disables downstream groupaddress frame forwarding.

Type: Privileged
ruckus(config-domain-zone-wlan)#
dhcp-option-82

Enables DHCP option 82.

Type: Privileged
ruckus(config-domain-zone-wlan)#
dhcp-option-82-format

[ ruckus-gre | soft-gre ] Enables DHCP option 82 format
options.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

110

Configuration Commands
domain

Table 43. Commands related to ruckus(config-domain-zone-wlan)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-wlan)#
disable-band-balancing

Description
Disables radio band balancing
on WLAN.

Type: Privileged
ruckus(config-domain-zone-wlan)#
disable-load-balancing

Disables client load balancing
on WLAN.

Type: Privileged
ruckus(config-domain-zone-wlan)#
disable-wlan

Disables this WLAN service.

Type: Privileged
ruckus(config-domain-zone-wlan)#
dnlink-limit

Sets the downlink rate limiting.

Type: Privileged
ruckus(config-domain-zone-wlan)#
enable-type

Enables the WLAN service type.

Type: Privileged
ruckus(config-domain-zone-wlan)#
enc-algorithm

Sets the encryption algorithm.

Type: Privileged
ruckus(config-domain-zone-wlan)#
enc-method

Sets the encryption method.

Type: Privileged
ruckus(config-domain-zone-wlan)#
enc-passphrase



Sets the encryption
passphrase.

ruckus(config-domain-zone-wlan)#
enc-wep-key




Sets WEP key (HEX).

Type: Privileged

WEP key (HEX), length
should be 10 (WEP-64)
or 26 (WEP-128)

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

111

Configuration Commands
domain

Table 43. Commands related to ruckus(config-domain-zone-wlan)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-wlan)#
force-dhcp

timeout 

Sets the timeout for DHCP in
seconds.

Type: Privileged

timeout: Sets the
disconnect client
timeout interval
: Sets the
disconnect client
timeout in intervals of 5
- 15 seconds

ruckus(config-domain-zone-wlan)#
forwarding-policy

Sets the forwarding policy
configurations.

Type: Privileged
ruckus(config-domain-zone-wlan)#
guest-access



Sets the guest access service.

Type: Privileged
ruckus(config-domain-zone-wlan)#
guest-access-auth-service

Sets the authentication server.

Type: Privileged
ruckus(config-domain-zone-wlan)#
hide-ssid

Hides SSID in beacon
broadcast.

Type: Privileged
ruckus(config-domain-zone-wlan)#
hotspot



Sets the hotspot service.



Sets the hotspot 2.0
configuration.



Sets the inactivity timeout.
Terminates idle user sessions
after the specified seconds of
inactivity.

[  ]

Sets the layer 2 access control
list.

Type: Privileged
ruckus(config-domain-zone-wlan)#
hotspot2
Type: Privileged
ruckus(config-domain-zone-wlan)#
inactivity-timeout
Type: Privileged
ruckus(config-domain-zone-wlan)# l2acl
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

112

Configuration Commands
domain

Table 43. Commands related to ruckus(config-domain-zone-wlan)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-wlan)#
mac-802-11x-format

Sets the MAC authentication.
Sets the MAC address in 802.1X
format.

Type: Privileged
ruckus(config-domain-zone-wlan)#
mac-auth

Description



Sets the MAC authentication.



Sets the maximum clients.
Allows clients per AP radio to
associate with this WLAN.
Range is between 1 and 512.
Sets the management Tx rates.

Type: Privileged

[ 5.5mbps | 48mbps |
6mbps | 2mbps |
36mbps | 1mbps |
18mbps | 12mbps |
54mbps | 9mbps |
11mbps | 24mbps ]

ruckus(config-domain-zone-wlan)# no

access-network

Type: Privileged

acct-delay-time

Disables or deletes the
configuration settings.

Type: Privileged
ruckus(config-domain-zone-wlan)#
max-clients
Type: Privileged
ruckus(config-domain-zone-wlan)#
mgmt-tx-rate

acct-service
acct-service-use-proxy
acct-ttg-session
auth-service-use-proxy
bss-minrate
client-fingerprinting
client-tx-rx-statistics
device-policy
dgaf
dhcp-option-82
disable-bandbalancing
disable-load-balancing
disable-wlan
dnlink-limit

................................continue

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

113

Configuration Commands
domain

Table 43. Commands related to ruckus(config-domain-zone-wlan)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-wlan)# no

force-dhcp

Type: Privileged

hide-ssid

Disables or deletes the
configuration settings.

l2-acl
mac-802-11x-format
mac-auth
ofdm-only (Orthogonal
Frequency Division
Multiplexing)
onboarding-authservice-use-proxy
proxy-arp
qinq-vlan
roam
support-802-11d
uplink-limit
user-traffic-profile
vlan-enabled
wireless-client-isolation
zero-it-activation
zero-it-onboarding
ruckus(config-domain-zone-wlan)#
ofdm-only

Enables OFDM (Orthogonal
Frequency Division Multiplexing)
rates.

Type: Privileged
ruckus(config-domain-zone-wlan)#
onboarding-auth-service



Sets the onboarding
authentication service.

Type: Privileged
ruckus(config-domain-zone-wlan)#
onboarding-auth-service-use-proxy
Type: Privileged

Sets the onboarding
authentication service using the
SCG proxy server.

ruckus(config-domain-zone-wlan)#
priority

Sets the priority as either low or
high.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

114

Configuration Commands
domain

Table 43. Commands related to ruckus(config-domain-zone-wlan)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-wlan)#
proxy-arp

Description
Enables proxy ARP.

Type: Privileged
ruckus(config-domain-zone-wlan)#
qinq-vlan



Enables Q-in-Q VLAN.



Sets the RADIUS NAS ID.



Sets the maximum number of
retries for RADIUS NAS.



Sets the reconnection to the
primary RADIUS NAS.



Sets the RADIUS NAS request
timeout.

Type: Privileged
ruckus(config-domain-zone-wlan)#
radius-nas-id
Type: Privileged
ruckus(config-domain-zone-wlan)#
radius-nas-max-retries
Type: Privileged
ruckus(config-domain-zone-wlan)#
radius-nas-reconnect-primary
Type: Privileged
ruckus(config-domain-zone-wlan)#
radius-nas-request-timeout
Type: Privileged
ruckus(config-domain-zone-wlan)#
radius-nas-type

Sets the RADIUS NAS type.

Type: Privileged
ruckus(config-domain-zone-wlan)#
roam

Enables roaming.

Type: Privileged
ruckus(config-domain-zone-wlan)#
roam-factor

2.4g 

Sets the roam factor.

5g 

Type: Privileged
ruckus(config-domain-zone-wlan)#
scheduler

[  ]

Sets the WLAN scheduler
profile.

Type: Privileged
ruckus(config-domain-zone-wlan)# ssid 
Type: Privileged

Sets the WLAN SSID
configuration.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

115

Configuration Commands
domain

Table 43. Commands related to ruckus(config-domain-zone-wlan)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-wlan)#
support-802-11d

Description
Enables support for 802.11d.

Type: Privileged
ruckus(config-domain-zone-wlan)#
uplink-limit

Sets the uplink rate limiting.

Type: Privileged
ruckus(config-domain-zone-wlan)#
user-traffic-profile

Sets the user traffic profile.

Type: Privileged
ruckus(config-domain-zone-wlan)#
vlan-enabled

Enables dynamic VLAN.

Type: Privileged
ruckus(config-domain-zone-wlan)#
vlan-id



Sets the VLAN ID



Sets the web authentication
service.

Type: Privileged
ruckus(config-domain-zone-wlan)#
web-authentication
Type: Privileged
ruckus(config-domain-zone-wlan)#
wireless-client-isolation

Sets the wireless client Isolation.

Type: Privileged
ruckus(config-domain-zone-wlan)#
zero-it-activation
Type: Privileged
ruckus(config-domain-zone-wlan)#
zero-it-onboarding

Enables zero-it activation
(WLAN users are provided with
wireless configuration installer
after they log in).

Type: Privileged

Enables zero-it device
registration from the guest
portal.

ruckus(config-domain-zone-wlan)# do

Executes the do command.

Type: Privileged
ruckus(config-domain-zone-wlan)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

116

Configuration Commands
domain

Table 43. Commands related to ruckus(config-domain-zone-wlan)
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-wlan)# exit

Description
Exits from the EXEC.

Type: Privileged
ruckus(config-domain-zone-wlan)# help

Displays the help.

Type: Privileged

Table 44 lists the related domain-zone-wlan-group configuration commands.
.

Table 44. Commands related to ruckus(config-domain-zone-wlan-group).
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-wlangroup)# description



Sets the description,

wlan 

Disables or removes WLAN
from this group.

Type: Privileged
ruckus(config-domain-zone-wlangroup)# no
Type: Privileged
ruckus(config-domain-zone-wlangroup)# wlan

 vlan  Sets a WLAN in this group or
overrides VLAN setting.
nasid 

Type: Privileged

 nasid 
vlan 
 vlan 
 nasid 


ruckus(config-domain-zone-wlangroup# do

Executes the do command.

Type: Privileged
ruckus(config-domain-zone-wlangroup)# end
Type: Privileged
ruckus(config-domain-zone-wlangroup# exit

Ends the current configuration
session and returns to
privileged EXEC mode.
Exits from the EXEC.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

117

Configuration Commands
domain

Table 44. Commands related to ruckus(config-domain-zone-wlan-group).
Syntax and Type

Parameters (if any)

ruckus(config-domain-zone-wlangroup)# help

Description
Displays the help.

Type: Privileged

Table 45 lists the related domain-zone-wlan-scheduler configuration commands.
.

Table 45. Commands related to ruckus (config-domain-zone-wlan-scheduler)
Syntax and Type

Parameters (if any)

Description

ruckus(config-domain-zone-wlanscheduler)# description



Sets the description,

${state} ${weekday}
${from} ${to}

Sets the schedule table.

Type: Privileged
ruckus(config-domain-zone-wlanscheduler)# schedule-data
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

118

3

Configuration Commands

This chapter describes the commands that you can use to configure, enable, and
disable various SCG components. The following table lists the commands.
NOTE: For easy access and reading, the configuration chapter has been split into
3 chapters based on the alphabetical order of commands.
Table 46. Configuration commands
eap-aka

eap-sim

encrypt-mac-ip end

event

event dbpersistence

event email

event snmptrap

event-email

exit

ftp-server

ftp-test

ggsn-service

help

hlr-mnc-ndc

hlr-service

hlr-systemwide

hostname

hotspot-profile interface

ip defaultgateway

ip internalsubnet

ip name-server ip route

l2ogre-profile

l3ogre-profile

lbs-service

license import lineman

mgmt-acl

mvno

network-trafficprofile

logging console lwapp2scg

ip separateaccess-core

no 3rd-zone

no acct-profile no admin

no adminradius

no advforwarding-profile

no ap

no ap autotagging

no ap-certcheck

no apcontrolmgmt-tos

no ap-root-ca

no ap-sci

no authprofile

no cgf-service no cls-sess
msisdn

no controlplane

no data-plane no dhcpservice

no domain

no dp-group

no eap-aka

no eap-sim

no event

no ftp-server

no encryptmac-ip

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

no cls-sess

119

Configuration Commands

Table 46. Configuration commands
no ggsnservice

no hlr-mncndc

no hlr-service no hotspotprofile

no ip

no l2ogreprofile

no l3ogreprofile

no lbs-service no lineman

no logging

no mvno

no networktraffic-profile

no pmipv6profile

no report

no rks-gre

no role

no snmp-trap no snmp-v2community

no snmp-v3user

no soft-gre

no
no ttg-pdgsubpackages profile

no user-role

no usertraffic-profile

no zone

northbound- northbound-portal
authtype

ntp-server

pmipv6profile

q-in-qethertype

radiusservice

rks-gre

role

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

no interface

no radius-service

no user-agentblacklist

report

120

Configuration Commands
eap-aka

eap-aka
To setup the EAP-AKA configuration, use the following command.
ruckus(config)# eap-aka 
Syntax Description
This command uses the following syntax:
enable: Enable EAP-AKA
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# eap-aka enable

Related Commands
Table 47 lists the related eap-aka configuration commands.
)

Table 47. Commands related to ruckus(config-eap-aka)
Syntax and Type

Parameters (if any)

ruckus(config-eap-aka)# active-secret

Description
Sets the EAP-AKA active secret
key number.

Type: Privileged
ruckus(config-eap-aka)# cachecleanup

Enables cache cleanup setting.

Type: Privileged
ruckus(config-eap-aka)# cachecleanup-time

 

Sets the cache cleanup setting.



Sets the cache history length.

Type: Privileged
ruckus(config-eap-aka)# cachehistory-len
Type: Privileged
ruckus(config-eap-aka)# fast-reauth

Enables re-authentication
support.

Type: Privileged
ruckus(config-eap-aka)# max-reauth
Type: Privileged



Sets the maximum successive
re-authentication.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

121

Configuration Commands
eap-aka

Table 47. Commands related to ruckus(config-eap-aka)
Syntax and Type

Parameters (if any)

Description

ruckus(config-eap-aka-sim)# no

cache-cleanup

Disables various options.

Type: Privileged

fast-reauth
secret
user-id-privacy

ruckus(config-eap-aka)# reauth-realm 
Type: Privileged
ruckus(config-eap-aka)# secret



Sets the re-authentication
realm.
Adds EAP-AKA secret key.

Type: Privileged
ruckus(config-eap-aka)# user-idprivacy

Enables the user Id privacy
support.

Type: Privileged
ruckus(config-eap-aka)# do

Executes the do command.

Type: Privileged
ruckus(config-eap-aka)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-eap-aka)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-eap-aka)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

122

Configuration Commands
eap-sim

eap-sim
To setup the EAP-SIM configuration, use the following command.
ruckus(config)# eap-sim 
Syntax Description
This command uses the following syntax:
enable: Enable EAP-SIM
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# eap-sim enable

Related Commands
Table 48 lists the related eap-sim configuration commands.
Table 48. Commands related to ruckus(config-eap-sim)
Syntax and Type

Parameters (if any)

ruckus(config-eap-sim)# active-secret

Description

Type: Privileged

Sets the EAP-SIM active secret
key number.

ruckus(config-eap-sim)# cachecleanup

Enables the cache cleanup
settings.

Type: Privileged
ruckus(config-eap-sim)# cachecleanup-time

 

Set the cache cleanup settings.



Set the cache history length.

Type: Privileged
ruckus(config-eap-sim)# cachehistory-len
Type: Privileged
ruckus(config-eap-sim)# fast-reauth
Type: Privileged

Enables re-authentication
support.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

123

Configuration Commands
eap-sim

Table 48. Commands related to ruckus(config-eap-sim)
Syntax and Type

Parameters (if any)

Description

ruckus(config-eap-sim)# max-reauth



Sets the maximum successive
re-authentication.

ruckus(config-eap-sim)# no

cache-cleanup

Disables various options.

Type: Privileged

fast-reauth

Type: Privileged

secret
user-id-privacy:
ruckus(config-eap-sim)# reauth-realm 

Sets the re-authentication realm.

Type: Privileged
ruckus(config-eap-sim)# secret



Adds EAP-SIM secret key.

Type: Privileged
ruckus(config-eap-sim)# user-idprivacy

Enables the user Id privacy
support.

Type: Privileged
ruckus(config-eap-sim)# do

Executes the do command.

Type: Privileged
ruckus(config-eap-sim)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-eap-sim)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-eap-sim)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

124

Configuration Commands
encrypt-mac-ip

encrypt-mac-ip
To enable encryption of MAC and IP address, use the following command.
ruckus(config)# encrypt-mac-ip
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# encrypt-mac-ip
Successful operation

end
To end the current session and returns to privileged EXEC mode, use the following
command.
ruckus(config)# end
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# end

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

125

Configuration Commands
event

event
To update the event notification configuration, use the following command.
ruckus(config)# event 
Syntax Description
This command uses the following syntax:
: Single configuration event notification
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# event 1002

Related Commands
Table 49 lists the related event configuration commands.
Table 49. Commands related to ruckus(config-event)
Syntax and Type

Parameters (if any)

ruckus(config-event)# dbpersistence

Description
Enables the data blade persistence
for the event.

Type: Privileged
ruckus(config-event)# email

Enables the email notification.

Type: Privileged
ruckus(config-event)# no

db-persistence

Type: Privileged

email

Disables various options.

snmp-trap
ruckus(config-event)# snmp-trap

Enables the SNMP trap.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

126

Configuration Commands
event db-persistence

event db-persistence
To enable data base persistence for the event, use the following command.
ruckus(config)# event db-persistence
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# event db-persistence
No. Event Code Category Type Description Severity SNMP Email
DB Persistence
--------- ----------- --------------- ----------------------1 103 AP Communication AP status changed to Managed This event
occurs when AP is appro Informational Enabled
Enabled
Enabled
by the SCG.
2
105
AP Communication
AP rejected
This event occurs when AP is rejected Minor Enabled by the SCG.
3
106
AP Communication
AP firmware updated
This event occurs when AP successful Informational Enabled updates
the firmware details to the SCG.
Please choose Event Codes (separated by ',') to enable DB persistence
events:

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

127

Configuration Commands
event email

event email
To enable event triggers for selected email notification, use the following command.
ruckus(config)# event email 
Syntax Description
This command has no arguments or keywords.
Command Mode
Config
Example
SCG30(config)# event email 305, 214, 113

event snmp-trap
To enable the events to trigger the SNMP trap, use the following command.
ruckus(config)# event snmp-trap 
Syntax Description
This command has no arguments or keywords.
Command Mode
Config
Example
SCG30(config)# event snmp-trap 305,114,102

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

128

Configuration Commands
event-email

event-email
To setup the event to email services, use the following command.
ruckus(config)# event-email 
Syntax Description
This command has no arguments or keywords.
Command Mode
Config
Example
SCG30(config)# event-email
SCG30(config-event-email)#

Related Commands
Table 50 lists the related event-email configuration commands.
Table 50. Commands related to ruckus(config-event-email)
Syntax and Type

Parameters (if any)

ruckus(config-event-email)# do

Description
Enables the do command.

Type: Privileged
ruckus(config-event-email)# enable

Enables the email notifications for
events.

Type: Privileged
ruckus(config-event-email)# mail-to



Type: Privileged

Enables the email address
configuration.

ruckus(config-event-email)# end:
Privileged

End the current configuration
session and returns to the
privileged EXEC mode.

ruckus(config-event-email)# exit
Privileged

Exit from the EXEC.

ruckus(config-event-email)# help
Privileged

Display the help message.

ruckus(config-event)# no

enable

Type: Privileged

email

Disables various options.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

129

Configuration Commands
exit

exit
To exit from the EXEC, use the following command.
ruckus(config)# exit
Syntax Description
This command has no arguments or keywords.
Command Mode
Config
Example
SCG30(config)# exit

ftp-server
To update the FTP server for uploading reports configuration, use the following
command.
ruckus(config)# ftp-server 
Once you enter the config-ftp-server context, you can configure the rest of the FTP
server settings (see example below).
Syntax Description
This command has no arguments or keywords
Default
This command has no default settings.
Command Mode
config
Example
SCG30(config)# ftp-server
SCG30(config-ftp-server)#
SCG30(config-ftp-server)#
SCG30(config-ftp-server)#
SCG30(config-ftp-server)#
Retype: ****
SCG30(config-ftp-server)#
SCG30(config)#

ftp1
host 1.1.1.1
port 21
username test
password test
exit

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

130

Configuration Commands
ftp-server

Related Commands
Table 51 lists the related ftp-server commands.
Table 51. Commands related to ruckus(config-ftp-server)
Syntax and Type

Parameters (if any)

ruckus(config-ftp-server)# enable

Enable for uploading reports to the
FTP server.

Type: Privileged
ruckus(config-ftp-server)# host

Description



Sets the FTP server IP address.



Disables uploaded reports to the
FTP server.



Sets the FTP password.



Sets the FTP server port.

[ daily | hourly ]

Sets the statistics data interval.



Sets the FTP remote directory.



Sets the FTP server port.

Type: Privileged
ruckus(config-ftp-server)# no
Type: Privileged
ruckus(config-ftp-server)# password
Type: Privileged
ruckus(config-ftp-server)# port
Type: Privileged
ruckus(config-ftp-server)# statsinterval
Type: Privileged
ruckus(config-ftp-server)# remotedirectory
Type: Privileged
ruckus(config-ftp-server)# port
Type: Privileged
ruckus(config-ftp-server)# test

Test the FTP settings.

Type: Privileged
ruckus(config-ftp-server)# username



Sets the user name.

Type: Privileged
ruckus(config-ftp-server)# do

Executes the do command.

Type: Privileged
ruckus(config-ftp-server)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-ftp-server)# exit

Exits from the EXEC.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

131

Configuration Commands
ftp-test

Table 51. Commands related to ruckus(config-ftp-server)
Syntax and Type

Parameters (if any)

ruckus(config-ftp-server)# help

Description
Displays the help.

Type: Privileged

ftp-test
To test the FTP server connection, use the following command.
ruckus(config)# ftp-test 
Syntax Description
This command uses the following syntax:
: FTP server name
Default
This command has no default settings.
Command Mode
config
Example
SCG30(config)# ftp-server FTP-SERVER
Fail to connection to FTP server

ggsn-service
To create or update the APN resolution to GGSN / PGW configuration, use the
following command.
ruckus(config)# ggsn-service >
ruckus(config)# ggsn-service >
ruckus(config)# ggsn-service >
ruckus(config)# ggsn-service >
ruckus(config)# ggsn-service >
ruckus(config)# ggsn-service >
ruckus(config)# ggsn-service >

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

132

Configuration Commands
ggsn-service

Syntax Description
This command uses the following syntax:
apn 
apn: Creates or updates the APN resolution to GGSN / PGW configuration
: Name of the APN
dns-retry 
dns-retry: Sets the number of DNS retry
: Number of DNS retries
dns-server  priority [down | up ]
dns-server: Sets the DNS server
 DNS server IP address
priority [down | up ]: Change DNS server priority by moving the priority either
up or down.
dns-timeout 
dns-timeout: Sets the DNS response timeout in seconds
: DNS response timeout
request-timer 
request-timer: Sets the echo request timer in seconds
: Echo request timeout
response-timer 
response-timer: Sets the echo response timer in seconds
: Echo response timeout
retry 
retry: Sets the number of retries
: Number of retries
Default
This command has no default settings.

Command Mode
Config

Example
SCG30(config)# ggsn-service apn app1
SCG30(config)# ggsn-service dns-retry 10

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

133

Configuration Commands
ggsn-service

SCG30(config)#
SCG30(config)#
SCG30(config)#
SCG30(config)#
SCG30(config)#

ggsn-service
ggsn-service
ggsn-service
ggsn-service
ggsn-service

dns-server host 1.1.1.1
dns-timeout 120
request-timer 90
response-timer 180
retry 05

Related Commands
Table 52 lists the related ggsn-service-apn configuration commands.
Table 52. Commands related to ruckus(config-ggsn-service-apn)
Syntax and Type

Parameters (if any)

ruckus(config-ggsn-service-apn)# ip 

Description
Sets the GGSN IP address.

Type: Privileged
ruckus(config-ggsn-service-apn)# do

Executes the do command.

Type: Privileged
ruckus(config-ggsn-service-apn)#
end
Type: Privileged
ruckus(config-ggsn-service-apn)#
exit

Ends the current configuration
session and returns to privileged
EXEC mode.
Exits from the EXEC.

Type: Privileged
ruckus(config-ggsn-service-apn)#
help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

134

Configuration Commands
help

help
To display the help message, use the following command.
ruckus(config)# help
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# help

hlr-mnc-ndc
To setup the HLR service MNC to NDC mapping configuration, use the following
command.
ruckus(config)# hlr-mnc-ndc
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# hlr-mnc-ndc 345 346 679

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

135

Configuration Commands
hlr-mnc-ndc

Related Commands
Table 53 lists the related hlr-mnc-ndc server configuration commands.
Table 53. Commands related to ruckus(config-hlr-mnc-ndc)
Syntax and Type

Parameters (if any)

Description

ruckus(config-hlr-mnc-ndc)# mcc



Sets the mobile country code.



Sets the mobile network code.



Type: Privileged

Sets the network destination
code.

ruckus(config-hlr-mnc-ndc)# do

Executes the do command.

Type: Privileged
ruckus(config-hlr-mnc-ndc)# mnc
Type: Privileged
ruckus(config-hlr-mnc-ndc)# ndc

Type: Privileged
ruckus(config-hlr-mnc-ndc)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-hlr-mnc-ndc)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-hlr-mnc-ndc)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

136

Configuration Commands
hlr-service

hlr-service
To setup the HLR service MNC to NDC mapping configuration, use the following
command.
ruckus(config)# hlr-service 
Syntax Description
This command uses the following syntax:
name: Name of the HLR service
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# hlr-service hlr2

Related Commands
• Table 54 lists the related hlr-service configuration commands.
• Table 55 lists the related hlr service sccp gtt configuration commands.
• Table 56 lists the related hlr service sctp configuration commands.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

137

Configuration Commands
hlr-service

Table 54 lists the related hlr-service configuration commands.
Table 54. Commands related to ruckus(config-hlr-service)
Syntax and Type

Parameters (if any)

ruckus(config-hlr-service)# authcaching

Description
Enables authorization caching.

Type: Privileged
ruckus(config-hlr-service)# auth-map- [version3 | version2 ]
version

Sets the authorization MAP
version.

Type: Privileged
ruckus(config-hlr-service)# av-caching

Enables AV caching.

Type: Privileged
ruckus(config-hlr-service)# cachecleanup-time

daily  

Sets the cache cleanup time.



Sets the cache history in
seconds.

[ integer | dotted ]

Sets the default point code
format.

Type: Privileged
ruckus(config-hlr-service)# cachehistory-time
Type: Privileged
ruckus(config-hlr-service)# defaultpoint-code-format
Type: Privileged
ruckus(config-hlr-service)# description 

Sets the description.

Type: Privileged
ruckus(config-hlr-service)# dest-gtindicator

[1|2]

Type: Privileged

1: Global title includes
translation type only

Sets the destination global title
indicator.

2: Global title includes
translation type,
numbering plan,
encoding scheme and
nature of address
indicator

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

138

Configuration Commands
hlr-service

Table 54. Commands related to ruckus(config-hlr-service)
Syntax and Type

Parameters (if any)

Description

ruckus(config-hlr-service)# destnature-addr-indicator

[ 3 | 4 | 1 | 5 | 2 ] where

Sets the destination address
indicator.

Type: Privileged

3: Reserved for National
Use
4: National Significant
Number
1: Unknown
5:International Number
2: Subscriber Number

ruckus(config-hlr-service)# destnumbering-plan
Type: Privileged

ruckus(config-hlr-service)# desttranslation-type

<1>
1: ISDN mobile
numbering plan
(recommendations
E.214)


Sets the destination numbering
plan.

Sets the destination translation
type.

Type: Privileged
ruckus(config-hlr-service)# do

Executes the do command.

Type: Privileged
ruckus(config-hlr-service)# end
Type: Privileged

Ends the current configuration
session and returns to
privileged EXEC mode.

ruckus(config-hlr-service)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-hlr-service)# help

Displays the help.

Type: Privileged
ruckus(config-hlr-service)# eap-simmap-version

[version2 | version3]

Sets the EAP-SIM MAP version.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

139

Configuration Commands
hlr-service

Table 54. Commands related to ruckus(config-hlr-service)
Syntax and Type

Parameters (if any)

Description

ruckus(config-hlr-service)# gt-pointcode



Sets the GT point code.

Type: Privileged

  

ruckus(config-hlr-service)# localnetwork-indicator

[3|2|1|4]

Type: Privileged

3: National

Sets the local network indicator.

where:
2: International Spare
1:International
4: National Spar e

ruckus(config-hlr-service)# local-point- 
code
Type: Privileged

Sets the local point code.

  

ruckus(config-hlr-service)# max-reuse- 
time

Sets the maximum reuse time.

Type: Privileged
ruckus(config-hlr-service)# no

auth-caching

Type: Privileged

av-caching

Disables various options.

sccp-gtt 
sctp 
source-has-point-code
ruckus(config-hlr-service)# routingcontext



Sets the routing context.



Sets the SCCP GTT table
configuration.



Sets the SCTP association to
core network configuration.

Type: Privileged
ruckus(config-hlr-service)# sccp-gtt
Type: Privileged
ruckus(config-hlr-service)# sctp
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

140

Configuration Commands
hlr-service

Table 54. Commands related to ruckus(config-hlr-service)
Syntax and Type

Parameters (if any)

ruckus(config-hlr-service)# sgsn-isdn- 
addr

Description
Sets the SGSN ISDN address.

Type: Privileged
ruckus(config-hlr-service)# source-gt- [ 2 | 1 ]
indicator
Type: Privileged

Sets the source GT indicator to:
2: Global title Includes
translation type, numbering
plan, encoding scheme and
nature of address indicator.
1: Global title includes
translation type only.

ruckus(config-hlr-service)# sourcehas-point-code

Enables the source point code.

Type: Privileged
ruckus(config-hlr-service)# sourcenature-addr-indicator

[3|2|4|1|5]

Type: Privileged

Sets the source nature address
of indicator to:
3: Reserved for National Use
2: Subscriber Number
4: National Significant
Number
1: Unknown
5:International Number

ruckus(config-hlr-service)# sourcenumbering-plan
Type: Privileged

ruckus(config-hlr-service)# sourcetranslation-type

<1>
1: ISDN mobile
numbering plan
(recommendations
E.163 and E.164).


Sets the source numbering
plan.

Sets the source translation type.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

141

Configuration Commands
hlr-service

Table 55 lists the related hlr-service configuration commands.
Table 55. Commands related to ruckus(config-hlr-service-sccp-gtt)
Syntax and Type

Parameters (if any)

Description

ruckus(config-hlr-service-sccp-gtt)#
addr-indicator

[2|1]

Sets the address indicator.
2: Route on SSN

Type: Privileged
ruckus(config-hlr-service-sccp-gtt)#
e164-address

1: Route on GT


Address as per
recommendations E.164.

[2|1]

Sets the GT indicator to:
2: Global title includes
translation type, numbering
plan, encoding scheme and
nature of address indicator.

Type: Privileged
ruckus(config-hlr-service-sccp-gtt)#
gt-indicator
Type: Privileged

1: Global title includes
translation type only.
ruckus(config-hlr-service-sccp-gtt)#
has-point-code

Sets the HAS point codes.

Type: Privileged
ruckus(config-hlr-service-sccp-gtt)#
has-ssn

Enables HAS upstream or
downstream SSN.

Type: Privileged
ruckus(config-hlr-service-sccp-gtt)#
nature-addr-indicator

[3|2|1|5|4]

Type: Privileged

Sets the destination nature of
address indicator to:
3: Reserved for national use
2: Subscriber number
1: Unknown
5: International number
4: National significant number

ruckus(config-hlr-service-sccp-gtt)#
no

has-point-code
has-ssn

Disables and deletes the set
configurations.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

142

Configuration Commands
hlr-service

Table 55. Commands related to ruckus(config-hlr-service-sccp-gtt)
Syntax and Type

Parameters (if any)

Description

ruckus(config-hlr-service-sccp-gtt)#
numbering-plan

[2 | 1]

Sets the numbering plan to:
2: ISDN/telephony numbering
plan (recommendations E.164)

Type: Privileged

1: ISDN mobile numbering plan
(recommendations E.214)
ruckus(config-hlr-service-sccp-gtt)# - 
Sets the point codes.
point-code
  
ruckus(config-hlr-service-sccp-gtt)#
translation-type



Sets the translation type.

Type: Privileged

Table 56 lists the related hlr-service- sctp configuration commands.
Table 56. Commands related to ruckus(config-hlr-service-sctp)
Syntax and Type

Parameters (if any)

Description

ruckus(config-hlr-service-sctp)# adjpoint-code



Sets the point codes.

Type: Privileged

  

ruckus(config-hlr-service-sctp)# dest- 
port

Sets the destination port.

Type: Privileged
ruckus(config-hlr-service-sctp)# max- 
inbound-streams

Sets the maximum inbound
streams.

Type: Privileged
ruckus(config-hlr-service-sctp)# max- 
outbound-streams

Sets the maximum outbound
streams.

Type: Privileged
ruckus(config-hlr-service-sctp)#
source-port



Sets the source port.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

143

Configuration Commands
hlr-system-wide

hlr-system-wide
To setup the HLR system wide configuration, use the following command.
ruckus(config)# hlr-system-wide
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# hlr-system-wide

Related Commands
Table 57 lists the related hlr-system-wide configuration commands.
Table 57. Commands related to ruckus(config-hlr-system-wide)
Syntax and Type
ruckus(config-hlr-system-wide)# do

Parameters (if any)

Description
Executes the do command.

Type: Privileged
ruckus(config-hlr-system-wide)#
enable

Enables MAP gateway.

Type: Privileged
ruckus(config-hlr-system-wide)#
map-gateway-1

Sets the MAP gateway.

Type: Privileged
ruckus(config-hlr-system-wide)#
map-gateway-2

Sets the MAP gateway.

Type: Privileged
ruckus(config-hlr-system-wide)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-hlr-system-wide)# exit

Exits from the EXEC.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

144

Configuration Commands
hostname

Table 57. Commands related to ruckus(config-hlr-system-wide)
Syntax and Type

Parameters (if any)

ruckus(config-hlr-system-wide)# help

Description
Displays the help.

Type: Privileged
ruckus(config-hlr-system-wide)# no
Type: Privileged

Disables the MAP gateway
Disables MAP gateway. services.



Clears MAP gateway 2
ruckus(config-hlr-system-wide)#
traffic-mode

[ override | load-share ] Sets the traffic mode by defining
the override and load share.

Type: Privileged

hostname
To change the hostname, use the following command.
ruckus(config)# hostname 
Syntax Description
This command uses the following syntax:
hostname: Changed hostname
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# hostname

This command will restart some services. Do you want to
continue (or input 'no' to cancel)? [yes/no]

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

145

Configuration Commands
hotspot-profile

hotspot-profile
To create or update the Hotspot (WISPr) service profile configuration, use the
following command.
ruckus(config)# hotspot profile 
Syntax Description
This command uses the following syntax:
name: Name of the Hotspot (WISPr) service profile
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# hotspot htsp1

Related Commands
Table 58 lists the related hotspot-profile configuration commands.
Table 58. Commands related to ruckus(config-hotspot-profile)
Syntax and Type

Parameters (if any)

Description

ruckus(config-hotspot-profile)# description



Sets the description.

Type: Privileged
ruckus(config-hotspot-profile# do

Executes the do command.

Type: Privileged
ruckus(config-hotspot-profile)# end
Type: Privileged

Ends the current
configuration session and
returns to privileged EXEC
mode.

ruckus(config-hotspot-profile)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-hotspot-profile)# grace-period 
Type: Privileged

Sets the EAP-SIM MAP
version.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

146

Configuration Commands
hotspot-profile

Table 58. Commands related to ruckus(config-hotspot-profile)
Syntax and Type

Parameters (if any)

ruckus(config-hotspot-profile)# help

Description
Displays the help.

Type: Privileged
ruckus(config-hotspot-profile)# location-id



Sets the location ID.



Sets the location name.

internal

Sets the logon model.

Type: Privileged
ruckus(config-hotspot-profile)# locationname
Type: Privileged
ruckus(config-hotspot-profile)# logon-url
Type: Privileged
external 
:
Redirects
unauthenticated user
to the URL for
authentication
ruckus(config-hotspot-profile)# name

Renames the hotspot
profile.

Type: Privileged
ruckus(config-hotspot-profile)# no walledgarden
Type: Privileged

ruckus(config-hotspot-profile)# sessiontimeout

 Allows unauthorized
destinations. Comma
separated IP address, IP
address range, CIDR and
domain name list.


Sets the session timeout.
Defined in minutes.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

147

Configuration Commands
hotspot-profile

Table 58. Commands related to ruckus(config-hotspot-profile)
Syntax and Type

Parameters (if any)

ruckus(config-hotspot-profile)# smart-client- none
support
enable
Type: Privileged
only 

Description
Sets the smart client
support.

only
Only smart client
allowed with
instructions for
enabling users to log
on using the Smart
Client application
ruckus(config-hotspot-profile)# start-page

original

Type: Privileged

redirect 

Sets the start page.

: Redirects
to the defined URL
ruckus(config-hotspot-profile)# walledgarden
Type: Privileged

 Enables walled garden.
Allows unauthorized
destinations. Commaseparated IP, IP range, CIDR
and regular expression
domain name list.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

148

Configuration Commands
interface

interface
To setup the interface configuration, use the following command.
ruckus(config)# interface 
ruckus(config)# interface 
ruckus(config)# interface 
ruckus(config)# interface >
Syntax Description
This command has no arguments or keywords.
Default
cluster 
cluster: Sets the cluster interface
: Name of the cluster
control: Sets the interface control configuration
management: Sets the management interface configuration
user-defined 
user-defined: Sets the user defined interface configuration
name: User defined interface name.
Command Mode
Config
Example
SCG30(config)# interface cluster
SCG30(config)# interface control
SCG30(config)# interface management
SCG30(config)# interface user-defined UD1

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

149

Configuration Commands
interface

Related Commands
Table 59 lists the related interface configuration commands.
Table 59. Commands related to ruckus(config-interface)
Syntax and Type

Parameters (if any)

ruckus(config-if)# do

Description
Executes the do command.

Type: Privileged
ruckus(config-if)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-if)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-if# help

Displays the help.

Type: Privileged
ruckus(config-if)# interface



Type: Privileged
ruckus(config-if)# name

Sets the physical interface such
as control interface.
Renames the user-define
interface.

Type: Privileged
ruckus(config-if)# ip



Type: Privileged

Sets the IP address of the
interface. DHCP is the IP
address negotiated by
DHCP.

Sets the IP address.

address  

Sets the IP address of the
interface, where  is
the static IP address,
 is the IP subnet
mask for the specified

ruckus(config-if)# service
Type: Privileged



Sets the services such as
hotspot.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

150

Configuration Commands
ip default-gateway

Table 59. Commands related to ruckus(config-interface)
Syntax and Type

Parameters (if any)

Description

ruckus(config-if)# vlan



Sets the VLAN ID for the
interface.

Type: Privileged

ip default-gateway
To setup the default gateway configuration, use the following command.
ruckus(config)# ip default-gateway cluster
ruckus(config)# ip default-gateway control
ruckus(config)# ip default-gateway management
Syntax Description
This command uses the following syntax:
cluster: Cluster interface
control: Control interface
management: Management interface
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# ip default-gateway control

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

151

Configuration Commands
ip internal-subnet

ip internal-subnet
To setup the IP address internal subnet, use the following command.
ruckus(config)# ip internal-subnet 
Syntax Description
This command uses the following syntax:
: Subnet prefix
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# ip internal-subnet prefix
This command will reboot internal interface, data planes and SMF
service. Do you want to continue?

ip name-server
To setup the name server configuration, use the following command.
ruckus(config)# ip name-server  
Syntax Description
This command uses the following syntax:
ip: Primary DNS server
ip: Secondary DNS server
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# ip name-server ip 172.19.13.56

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

152

Configuration Commands
ip route

ip route
To setup the static rule configuration, use the following command.
ruckus(config)# ip route     
Syntax Description
This command uses the following syntax:
    
: Destination network IP address
: Destination network mask
: Next hop IP address
: Interface
: Distance metric for this route
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# ip route ip 193.12.30.10

ip separate-access-core
To enable access and core gateway, use the following command.
ruckus(config)# ip separate-access-core 
Syntax Description
This command uses the following syntax:
enable: To enable access and core gateway
Default
This command has no default settings.
Command Mode
Config

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

153

Configuration Commands
l2ogre-profile

Example
SCG30(config)# ip separate-access-core enable

l2ogre-profile
To create or update the L2oGRE profile configuration, use the following command.
ruckus(config)# l2ogre-profile 
Syntax Description
This command uses the following syntax:
name: L2oGRE profile name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# l2ogre-profile l2g1

Related Commands
Table 60 lists the related 2ogre-profile configuration commands.
Table 60. Commands related to ruckus(config-l2ogre-profile)
Syntax and Type

Parameters (if any)

Description

ruckus(config-l2ogre-profile)# corenetwork-gateway



Set the core network
gateway IP address.

Type: Privileged
ruckus(config-l2ogre-profile)# description 
Type: Privileged

Sets the description. Length
is between 1 and 128.

ruckus(config-l2ogre-profile)# keep-alive- 
period

Sets the tunnel keep alive
period.

Type: Privileged
ruckus(config-l2ogre-profile)# keep-alive- 
retry

Sets the tunnel keep alive
retries.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

154

Configuration Commands
l2ogre-profile

Table 60. Commands related to ruckus(config-l2ogre-profile)
Syntax and Type

Parameters (if any)

Description

ruckus(config-l2ogre-profile)# no

tunnel-keep-alive

Disables L2oGRE settings.

Type: Privileged
ruckus(config-l2ogre-profile)# tunnelkeep-alive

Enables tunnel keep alive.

Type: Privileged
ruckus(config-l2ogre-profile)# tunnel-mtu auto - Auto MTU size
Type: Privileged
ruckus(config-l2ogre-profile)# do

Sets the tunnel MTU options.

 - Manual MTU
size
Executes the do command.

Type: Privileged
ruckus(config-l2ogre-profile)# end
Type: Privileged

Ends the current
configuration session and
returns to privileged EXEC
mode.

ruckus(config-l2ogre-profile)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-l2ogre-profile)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

155

Configuration Commands
l3ogre-profile

l3ogre-profile
To create or update the L3oGRE profile configuration, use the following command.
ruckus(config)# l3ogre-profile 
Syntax Description
This command uses the following syntax:
name: L3oGRE profile name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# l3ogre-profile l3g1

Related Commands
Table 61 lists the related l3ogre-profile configuration command
.

Table 61. Commands related to ruckus(config-l3ogre-profile)
Syntax and Type

Parameters (if any)

Description

ruckus(config-l3ogre-profile)# corenetwork-gateway



Set the core network
gateway IP address.



Sets the description.
Length is between 1 and
128.



Type: Privileged

Sets the DHCP relay
service.

ruckus(config-l3ogre-profile)# dhcp-relaytunnel

Enables DHCP relay
through tunnel.

Type: Privileged
ruckus(config-l3ogre-profile)# description
Type: Privileged
ruckus(config-l3ogre-profile)# dhcp-relay

Type: Privileged
ruckus(config-l3ogre-profile)# keep-aliveperiod



Sets the tunnel keep alive
period.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

156

Configuration Commands
l3ogre-profile

Table 61. Commands related to ruckus(config-l3ogre-profile)
Syntax and Type

Parameters (if any)

Description

ruckus(config-l3ogre-profile)# keep-aliveretry



Sets the tunnel keep alive
retries.

ruckus(config-l3ogre-profile)# no

dhcp-relay-tunnel

Disables L3oGRE settings.

Type: Privileged

tunnel-keep-alive

ruckus(config-l3ogre-profile)# tunnelinterface

data-plane 
 

Type: Privileged

Sets the gateway tunnel.

Type: Privileged
ruckus(config-l3ogre-profile)# tunnel-keepalive

Enables tunnel keep alive.

Type: Privileged
ruckus(config-l3ogre-profile)# tunnel-mtu
Type: Privileged
ruckus(config-l3ogre-profile)# do
Type: Privileged
ruckus(config-l3ogre-profile)# end

auto - Auto MTU size

Sets the tunnel MTU
 - Manual MTU options.
size
Executes the do
command.

Type: Privileged

Ends the current
configuration session and
returns to privileged EXEC
mode.

ruckus(config-l3ogre-profile)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-l3ogre-profile)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

157

Configuration Commands
lbs-service

lbs-service
To create and update the Location Based Service (LBS) configuration, use the
following command.
ruckus(config)# lbs-service
Syntax Description
This command uses the following syntax:
name: LBS venue name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# lbs-service name
SCG30(config-lbs-service)#

Related Commands
Table 62 lists the related lbs-service configuration command
.

Table 62. Commands related to ruckus(config-lbs-service).
Syntax and Type

Parameters (if any)

ruckus(config-lbs-service)# do

Description
Sets the do command.

Type: Privileged
ruckus(config-lbs-service)# end
Type: Privileged

Ends the current configuration
session and returns to the
privileged EXEC mode.

ruckus(config-lbs-service)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-lbs-service)# help

Displays the help message.

Type: Privileged
ruckus(config-lbs-service)# host




Sets the server address.

Type: Privileged
ruckus(config-lbs-service)# password



Sets the password.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

158

Configuration Commands
license import

Table 62. Commands related to ruckus(config-lbs-service).
Syntax and Type

Parameters (if any)

Description

ruckus(config-lbs-service)# port



Sets the port number.



Sets the LBS venue.

Type: Privileged
ruckus(config-lbs-service)# venue
Type: Privileged

license import
To setup the import licenses, use the following command.
ruckus(config)# license import 
Syntax Description
This command uses the following syntax:
ftp-url: License file. FTP URL format is, ftp://:@/

Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# license import ftp://mahan:ruckus1!@172.19.7.100

lineman
To setup the workflow URL, use the following command.
ruckus(config)# lineman 
Syntax Description
This command uses the following syntax:
: Set the workflow URL
Default
This command has no default settings.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

159

Configuration Commands
logging console

Command Mode
Config
Example
SCG30(config)# lineman https://172.19.10.4:8443

logging console
To enable service logging on the console, use the following command.
ruckus(config)# logging console cli [ error | info ] cli debug
Syntax Description
This command uses the following syntax:
cli: Enable CLI logging on the console
error: Enable CLI logging on the console and change logging level to ERROR
info: Enable CLI logging on the console and change logging level to INFO
debug: Enable CLI logging on the console and change logging level to DEBUG
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# logging console cli error

lwapp2scg
To update the LWAPP to SCG configurations, use the following command.
ruckus(config)# lwapp2scg
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

160

Configuration Commands
lwapp2scg

Example
SCG30(config)# lwapp2scg
SCG30(config)# lwapp2scg

Related Commands
Table 63 lists the related lwapp2scg configuration command
.

Table 63. Commands related to ruckus(config-lwapp2scg).
Syntax and Type

Parameters (if any)

Description

ruckus(config-lwapp2scg)# acl-ap

mac 

Sets the ACL AP.

Type: Privileged

mac: AP MAC IP address
: AP MAC IP
address. Separated with
comma. For example,
1a:2b:3c:4d:5f:60,11:22:
33:44:55:66
serial 
serial: AP serial number
: AP
serial number(s).
Separated with comma.
For example,
123456789012,9876543
21021

ruckus(config-lwapp2scg)# no acl-ap

Deletes the ACL AP.

Type: Privileged
ruckus(config-lwapp2scg)# do

Sets the do command

Type: Privileged
ruckus(config-lwapp2scg)# end
Type: Privileged

Ends the current
configuration session and
returns to the privileged
EXEC mode.

ruckus(config-lwapp2scg)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-lwapp2scg)# help

Displays the help message.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

161

Configuration Commands
mgmt-acl

Table 63. Commands related to ruckus(config-lwapp2scg).
Syntax and Type

Parameters (if any)

Description

ruckus(config-lwapp2scg)# pasv-port



Sets the dynamic data
transmission port range.

Type: Privileged
ruckus(config-lwapp2scg)# policy
Type: Privileged

 Accept by ACL Sets the ACL policy.
AP list
 Accept all
 Deny by ACL AP
list
 Deny all

mgmt-acl
To create or update the management interface access control list configuration, use
the following command.
ruckus(config)# mgmt-acl
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# mgmt-acl

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

162

Configuration Commands
mgmt-acl

Related Commands
Table 64 lists the related mgmt-acl server configuration commands.
.

Table 64. Commands related to ruckus(config-mgmt-acl)
Syntax and Type

Parameters (if any)

ruckus(config-mgmt-acl)# enable

Description
Enables the access control of
the management interface.

Type: Privileged
ruckus(config-mgmt-acl)# no

enable

Type: Privileged

rule

ruckus(config-mgmt-acl)# rule

: ACL rule name

Disables various options.

Type: Privileged

Creates or updates the
management interface ACL
rule configuration.

ruckus(config-mgmt-acl)# do

Executes the do command.

Type: Privileged
ruckus(config-mgmt-acl)# end
Type: Privileged

Ends the current
configuration session and
returns to privileged EXEC
mode.

ruckus(config-mgmt-acl)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-mgmt-acl)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

163

Configuration Commands
mgmt-acl

Table 65 lists the related mgmt-acl-rule configuration commands.
.

Table 65. Commands related to ruckus(config-mgmt-acl-rule)
Syntax and Type

Parameters (if any)

Description

ruckus(config-mgmt-acl-rule)#
description



Description of the server
created.

ruckus(config-mgmt-acl-rule)#
restriction

single : Sets single IP
restriction and IP address

Executes commands within
the context.

Type: Privileged

range  : Sets IP
range restriction with start
and end IP addresses

Type: Privileged

subnet  : Sets
the subnet restriction along
with network address and
subnet mask
ruckus(config-mgmt-acl-rule)# do

Executes the do command.

Type: Privileged
ruckus(config-mgmt-acl-rule)# end
Type: Privileged

Ends the current
configuration session and
returns to privileged EXEC
mode.

ruckus(config-mgmt-acl-rule)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-mgmt-acl-rule)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

164

Configuration Commands
mvno

mvno
To create or update the MVNO configuration, use the following command.
ruckus(config)# mvno 
Syntax Description
This command uses the following syntax:
name: MVNO name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# mvno mv1

Related Commands
• Table 66 lists the related mvno configuration commands.
• Table 67 lists the related mvno-admin configuration commands.
• Table 68 lists the related mvno admin radius configuration commands.
Table 66 lists the related mvno configuration commands.
Table 66. Commands related to ruckus(config-mvno)
Syntax and Type

Parameters (if any)

Description

ruckus(config-mvno)# admin



Adds an administrator account.



Set the RADIUS server for
administrators.

ruckus(config-mvno)# capabilities



Sets the capabilities.

Type: Privileged



Type: Privileged
ruckus(config-mvno)# admin-radius
Type: Privileged






SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

165

Configuration Commands
mvno

Table 66. Commands related to ruckus(config-mvno)
Syntax and Type

Parameters (if any)

Description

ruckus(config-mvno)# description



Sets the description.

Type: Privileged
ruckus(config-mvno)# do

Executes the do command.

Type: Privileged
ruckus(config-mvno)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-mvno)# exit

Exits from the EXEC.

Type: Privileged
ruckus(diagnostic))# help

Displays the help.

Type: Privileged
ruckus(config-mvno)# no

admin-radius

Type: Privileged



Disables and deletes
configuration commands.






wlan
zone
ruckus(config-mvno)# wlan



Adds a WLAN and WLAN name.



Adds a zone and zone name.

Type: Privileged
ruckus(config-mvno)# zone
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

166

Configuration Commands
mvno

Table 67 lists the related mvno-admin configuration commands.
l

Table 67. Commands related to ruckus(config-mvno-admin)
Syntax and Type

Parameters (if any)

Description

ruckus(config-mvno-admin)# email



Set the user’s email details.

Type: Privileged
ruckus(config-mvno-admin)# name 

Set the name of the user.

Type: Privileged
ruckus(config-mvno-admin)#
password



Set the password for user.

Type: Privileged
ruckus(config-mvno-admin)# phone 
Type: Privileged
ruckus(config-mvno-admin)# realname

Set the phone number of the
user.



Set the real name of the user.



Set the user’s job title.

Type: Privileged
ruckus(config-mvno-admin)# title
Type: Privileged
ruckus(config-mvno-admin)# do

Executes the do command.

Type: Privileged
ruckus(config-mvno-admin)# end
Type: Privileged

Ends the current configuration
session and returns to
privileged EXEC mode.

ruckus(config-mvno-admin)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-mvno-admin)# help

Displays the help.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

167

Configuration Commands
mvno

Table 68 lists the related mvno-admin-radius configuration commands.
l

Table 68. Commands related to ruckus(config-mvno-admin-radius)
Syntax and Type

Parameters (if any)

Description

ruckus(config-mvno-admin-radius)#
backup

ip 

Type: Privileged

shared-secret


Enables backup RADIUS
support and its related
settings.

port 

request-timeout

max-retry 
retry-prilnvl 
ruckus(config-mvno-admin-radius)# ip 
Type: Privileged
ruckus(config-mvno-admin-radius)#
no

Sets the IP addresses of
primary RADIUS server.

backup

Disables or deletes the
configuration settings.



Sets the port number of
primary RADIUS server.



Sets the realm service.
Multiple realms are supported
by using a comma (,)
separation. For example,
home1,home2.



Sets the service. Multiple
services are supported by
using a comma (,) separation.
For example, home1,home2.



Sets the shared secret of the
primary RADIUS server. The
length is between 1 and 255
characters.

[ radius | tacacs ]

Sets the authentication type as
either RADIUS or TACAS.

Type: Privileged
ruckus(config-mvno-admin-radius)#
port
Type: Privileged
ruckus(config-mvno-admin-radius)#
realm
Type: Privileged

ruckus(config-mvno-admin-radius)#
service
Type: Privileged
ruckus(config-mvno-admin-radius)#
shared-secret
Type: Privileged
ruckus(config-mvno-admin-radius)#
type
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

168

Configuration Commands
network-traffic-profile

Table 68. Commands related to ruckus(config-mvno-admin-radius)
Syntax and Type

Parameters (if any)

ruckus(config-mvno-admin-radius)#
do

Description
Executes the do command.

Type: Privileged
ruckus(config-mvno-admin-radius)#
end
Type: Privileged
ruckus(config-mvno-admin-radius#
exit

Ends the current configuration
session and returns to
privileged EXEC mode.
Exits from the EXEC.

Type: Privileged
ruckus(config-mvno-admin-radius)#
help

Displays the help.

Type: Privileged

network-traffic-profile
Sets the network traffic profile configuration, use the following command.
ruckus(config)# network-traffic-profile 
Syntax Description
This command uses the following syntax:
name: Name of the network traffic profile
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# network-traffic-profile ntp1

Related Commands
• Table 69 lists the related network profile configuration commands.
• Table 70 lists the related network traffic profile network acl configuration
commands.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

169

Configuration Commands
network-traffic-profile

Table 69 lists the related network-profile configuration commands.
.

Table 69. Commands related to ruckus(config-network-profile)
Syntax and Type

Parameters (if any)

ruckus(config-network-traffic-profile)# [ block | allow ]
default-action

Description
Sets the default action as either
block or allow.

Type: Privileged
ruckus(config-network-traffic-profile)# 
description

Sets the network traffic profile
description.

Type: Privileged
ruckus(config-network-traffic-profile)#
do

Executes the do command.

Type: Privileged
ruckus(config-network-traffic-profile)#
end
Type: Privileged
ruckus(config-network-traffic-profile)#
exit

Ends the current configuration
session and returns to privileged
EXEC mode.
Exits from the EXEC.

Type: Privileged
ruckus(config-network-traffic-profile)#
help

Displays the help.

Type: Privileged
ruckus(config-network-traffic-profile)#
network-acl

Sets the network access control
configurations.

Type: Privileged
ruckus(config-network-traffic-profile)# network-acl
no

Disables or deletes network traffic
profile settings, such as rate limit.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

170

Configuration Commands
network-traffic-profile

Table 70 lists the related network-traffic-profile-network-acl configuration
commands.
Table 70. Commands related to ruckus(config-network-traffic-profile-network-acl)
Syntax and Type

Parameters (if any)

Description

ruckus(config-network-trafficprofile-network-acl)# action

[ allow | block ]

Sets the permission
configurations as either allow or
block.

 subnet-mask


Sets the destination IP address.



Sets the destination port
configurations.

Type: Privileged
ruckus(config-network-trafficprofile-network-acl)# destination-ip
Type: Privileged
ruckus(config-network-trafficprofile-network-acl)# destinationport

range  

Type: Privileged
ruckus(config-network-trafficprofile-network-acl)# direction
Type: Privileged

[ upstream | downstream Sets the direction configurations
as either up stream or down
]
stream.

Type: Privileged

[ esp | udp | sctp | icmp | Sets the protocol configurations.
icmpv6 | igmp | udplite |
ah | tcp ]

ruckus(config-network-trafficprofile-network-acl)# source-ip

 subnet-mask


Sets the source IP address.



Sets the source port
configurations.

ruckus(config-network-trafficprofile-network-acl)# protocol

Type: Privileged
ruckus(config-network-trafficprofile-network-acl)# source-port
Type: Privileged
ruckus(config-network-trafficprofile-network-acl)# do

range  

Executes the do command.

Type: Privileged
ruckus(config-network-trafficprofile-network-acl)# end
Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

171

Configuration Commands
no 3rd-zone

Table 70. Commands related to ruckus(config-network-traffic-profile-network-acl)
Syntax and Type

Parameters (if any)

ruckus(config-network-trafficprofile-network-acl)# exit

Description
Exits from the EXEC.

Type: Privileged
ruckus(config-network-trafficprofile-network-acl)# help

Displays the help.

Type: Privileged

no 3rd-zone
To delete the 3rd Party AP zone configurations, use the following command.
ruckus(config)# no 3rd-zone 
Syntax Description
This command uses the following syntax:
name: 3rd Party AP zone name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no 3rd-zone ap3

no acct-profile
To delete accounting service profile configuration, use the following command.
ruckus(config)# no acct-profile 
Syntax Description
This command uses the following syntax:
name: Accounting service profile name
Default
This command has no default settings.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

172

Configuration Commands
no admin

Command Mode
Config
Example
SCG30(config)# no acct-profile acct1

no admin
To delete the administrator, use the following command.
ruckus(config)# no admin 
Syntax Description
This command uses the following syntax:
username: Name of the administrator to be deleted
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no admin ruckus

no admin-radius
To delete RADIUS servers configurations for administrators, use the following
command.
ruckus(config)# no admin-radius 
Syntax Description
This command uses the following syntax:
name: AAA server name
Default
This command has no default settings.
Command Mode
Config

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

173

Configuration Commands
no adv-forwarding-profile

Example
SCG30(config)# no admin-radius adr1

no adv-forwarding-profile
To delete advanced (mixed mode) profile configuration, use the following command.
ruckus(config)# no adv-forwarding-profile 
Syntax Description
This command uses the following syntax:
name: Advanced (mixed mode) name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no adv-forwarding-profile adv1

no ap
To delete the lock or unlock the access point, use the following command.
ruckus(config)# no ap  lock
Syntax Description
This command uses the following syntax:
mac: AP MAC address
lock: Unlock AP
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no ap 50:A7:33:24:EA:00

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

174

Configuration Commands
no ap auto-tagging

no ap auto-tagging
To disable auto tagging of critical access points, use the following command.
ruckus(config)# no ap auto-tagging 
Syntax Description
This command uses the following syntax:
enable: Disable the auto tagging for critical access point
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no ap auto-tagging enable

no ap-cert-check
To disable the access point certificate check, use the following command.
ruckus(config)# no ap-cert-check
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no ap-cert-check

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

175

Configuration Commands
no ap-control-mgmt-tos

no ap-control-mgmt-tos
To disable the access point control management traffic type of service, use the
following command.
ruckus(config)# no ap-control-mgmt-tos
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no ap-control-mgmt-tos

no ap-root-ca
To disable or delete the access point root ca, use the following command.
ruckus(config)# no ap-root-ca
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no ap-root-ca

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

176

Configuration Commands
no ap-sci

no ap-sci
To disable the access point sci configurations, use the following command.
ruckus(config)# no ap-sci 
Syntax Description
This command uses the following syntax:
enable: Disables the AP SCI.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no ap-sci enable

no auth-profile
To delete an authentication service configuration, use the following command.
ruckus(config)# no auth-profile 
Syntax Description
This command uses the following syntax:
name: Name of the authentication service to be deleted.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no auth-profile ap1

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

177

Configuration Commands
no cgf-service

no cgf-service
To delete CGF service configuration, use the following command.
ruckus(config)# no cgf-service 
Syntax Description
This command uses the following syntax:
name: CGF service name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no cgf-service cgf1

no cls-sess msisdn
To delete the session served by current node for the received MSISDN, use the
following command:
ruckus(config)# no cls-sess msisdn 
Syntax Description
msisdn : MSISDN and MSISDN value. The length of MSISDN should
be between 10 to15 digits.
Default
This command has no default settings.
Command Mode
Privileged
Example
SCG30(config)# no cls-sess msisdn 123456789012345

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

178

Configuration Commands
no cls-sess

no cls-sess
To delete all the sessions served by current node, use the following command:
ruckus(config)# no cls-sess
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Privileged
Example
SCG30(config)# no all-cls-sess

no control-plane
To remove the control plane from the cluster configuration, use the following
command.
ruckus(config)# no control-plane 
Syntax Description
This command uses the following syntax:
name: Control plane name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no control-plane cp1

no data-plane
To disable the STP package bridge of the local dataplane configuration, use the
following command.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

179

Configuration Commands
no dhcp-service

ruckus(config)# no data-plane  forward-stp
Syntax Description
This command uses the following syntax:
name: Dataplane name
forward-stp: Disables the STP package bridge
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no data-plane name indus7-d1

no dhcp-service
To delete DHCP service configuration, use the following command.
ruckus(config)# no dhcp-service 
Syntax Description
This command uses the following syntax:
name: DHCP service name.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no dhcp-service dhps1

no domain
To delete management domains or access point zones in a specific domain
configuration, use the following command.
ruckus(config)# no domain

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

180

Configuration Commands
no domain

Syntax Description
This command uses the following syntax:
 zone 
: Domain name
zone: Deletes AP zones of a specific domain
: AP zone name
 zone  ap 
: Domain name
zone: Deletes AP zones of a specific domain
: AP zone name
ap: Deletes an AP of a specific AP zone
: AP MAC address
 zone  wlan 
: Domain name
zone: Deletes AP zones of a specific domain
: AP zone name
wlan: Deletes WLANs of a specific AP zone
: WLAN name
 zone  aaa 
: Domain name
zone: Deletes AP zones of a specific domain
: AP zone name
aaa: Deletes AAA servers of a specific AP zone
: AAA server name
 zone  hotspot 
: Domain name
zone: Deletes AP zones of a specific domain
: AP zone name
hotspot: Deletes WISPr (Hotspot) of a specific AP zone
: WISPr (Hotspot) name
 zone  hotspot-v2-sp 
: Domain name
zone: Deletes AP zones of a specific domain
: AP zone name

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

181

Configuration Commands
no domain

hotspot-v2-sp: Deletes Hotspot 2.0 service provider profiles of a specific AP
zone
: Service provider profile name
 zone  hotspot-v2-op 
: Domain name
zone: Deletes AP zones of a specific domain
: AP zone name
hotspot-v2-op: Shows Hotspot 2.0 operator profiles of a specific AP zone
: Operator profile name
 zone  ap-group 
: Domain name
zone: Deletes AP zones of a specific domain
: AP zone name
ap-group: Deletes AP groups of a specific AP zone
: AP group name
 zone  wlan-group 
: Domain name
zone: Deletes AP zones of a specific domain
: AP zone name
wlan-group: Delete WLAN groups of a specific AP zone
: WLAN group name
 zone  ap-register-rule 
: Domain name
zone: Deletes AP zones of a specific domain
: AP zone name
ap-register-rule: Deletes AP registration rules of a specific AP zone
 AP registration rule
 zone  cluster-switch-over
: Domain name
zone: Disables the cluster switchover of a specific AP zone
: AP zone name
cluster-switch-over: Disables the cluster switchover

: Domain name

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

182

Configuration Commands
no dp-group

Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no domain indus5-d

no dp-group
To disable the dataplane grouping configuration, use the following command.
ruckus(config)# no dp-group
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no dp-group

no eap-aka
To disable the EAP_AKA configuration, use the following command.
ruckus(config)# no eap-aka 
Syntax Description
This command uses the following syntax:
enable: Disables the EAP-AKA
Default
This command has no default settings.
Command Mode
Config

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

183

Configuration Commands
no eap-sim

Example
SCG30 (config)# no eap-aka enable

no eap-sim
To disable the EAP_SIM configuration, use the following command.
ruckus(config)# no eap-sim 
Syntax Description
This command uses the following syntax:
enable: Disables the EAP-SIM
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no eap-sim enable

no encrypt-mac-ip
To disable the encryption of MAC and IP address, use the following command.
ruckus(config)# no encrypt-mac-ip
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no encrypt-mac-ip
Do you want to continue to disable (or input 'no' to cancel)? [yes/
no]

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

184

Configuration Commands
no event

no event
To disable the trigger to SNMP trap/email configuration, use the following command.
ruckus(config)# no event   
Syntax Description
This command uses the following syntax:
snmp-trap: Disables the trigger to SNMP trap
email: Disables the to trigger email
db-persistence: Disables DB persistence for the even
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no event email 305, 214, 113

no ftp-server
To delete FTP server, use the following command.
ruckus(config)# no ftp-server 
Syntax Description
This command uses the following syntax:
: Name of the FTP server
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no ftp-server ftp1

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

185

Configuration Commands
no ggsn-service

no ggsn-service
To delete GGSN APN resolutions or DNS servers, use the following command.
ruckus(config)# no ggsn-service > >
Syntax Description
This command uses the following syntax:
apn 
apn: APN resolution to GGSN configuration table
: Domain name
dns-server 
dns-server: DNS server
: DNS server IP
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no ggsn-service dns-server host 1.1.1.1

no hlr-mnc-ndc
To delete HLR service MNC to NDC mappings configurations, use the following
command.
ruckus(config)# no hlr-mnc-ndc   
Syntax Description
This command uses the following syntax:
  
mcc: Mobile country code
mnc: Mobile network code
ndc: Network destination code
Default
This command has no default settings.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

186

Configuration Commands
no hlr-service

Command Mode
Config
Example
SCG30(config)# no hlr-mnc-ndc 345 346 679

no hlr-service
To delete HLR service configuration, use the following command.
ruckus(config)# no hlr-service 
Syntax Description
This command uses the following syntax:
hlr-name: HLR service name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no hlr-service hlr11

no hotspot-profile
To delete hotspot service profile configuration, use the following command.
ruckus(config)# no hotspot-profile 
Syntax Description
This command uses the following syntax:
name: Hotspot service profile name
Default
This command has no default settings.
Command Mode
Config

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

187

Configuration Commands
no interface

Example
SCG30(config)# no hotspot-profile hpsp12

no interface
To disable an interface configuration, use the following command.
ruckus(config)# no interface >
Syntax Description
This command uses the following syntax:
user-defined: User defined interface
name: User defined interface name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no interface user-defined UD1

no ip
To remove all IP address static routes, use the following command.
ruckus(config)# no ip   
 [ cluster | management | control ]> 
Syntax Description
This command uses the following syntax:
route: Delete static routes
dest-network: Destination network
network-mask: Destination network mask
next-hop-ip: Next hop IP address
cluster: Cluster interface
management: Management interface
control: Control interface
name-server: Delete all name servers
secondary: Delete secondary name server

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

188

Configuration Commands
no l2ogre-profile

Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no ip route ip 193.12.30.10

no l2ogre-profile
To delete the L2oGRE configuration, use the following command.
ruckus(config)# no l2ogre 
Syntax Description
This command uses the following syntax:
name: L2oGRE profile name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no l2ogre l2g13

no l3ogre-profile
To delete the L3oGRE configuration, use the following command.
ruckus(config)# no l3ogre 
Syntax Description
This command uses the following syntax:
name: L3oGRE profile name
Default
This command has no default settings.

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

189

Configuration Commands
no l3ogre-profile

Command Mode
Config
Example
SCG30(config)# no l3ogre l3g19

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

190

Configuration Commands
no lbs-service

no lbs-service
To delete the location based service venue name. use the following command.
ruckus(config)# no lbs-service 
Syntax Description
This command uses the following syntax:
name: LBS venue name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no lbs-service lbs-service
Do you want to continue to delete (or input 'no' to cancel)? [yes/no]

no lineman
To delete the workflow URL, use the following command.
ruckus(config)# no lineman 
Syntax Description
This command uses the following syntax:
: Deletes the workflow URL
Default
This command has no default settings.
Command Mode
Config
Example
ruckus(config)# no lineman https://172.19.10.4:8443

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

191

Configuration Commands
no logging

no logging
To disable service logging settings, use the following command.
ruckus(config)# no logging 
Syntax Description
This command uses the following syntax:
console: Disables all services that logon to the console and reverts to default
settings.
cli: Disables the CLI logging on the console and changes the default log level
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no logging console cli

no mvno
To delete MVNO configurations, use the following command.
ruckus(config)# no mvno 
Syntax Description
This command uses the following syntax:
name: MVNO name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no mvno mv1

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

192

Configuration Commands
no network-traffic-profile

no network-traffic-profile
To delete the network traffic configuration, use the following command.
ruckus(config)# no network-traffic-profile 
Syntax Description
This command uses the following syntax:
name: Name of the network service to be deleted
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no network-traffic-profile ntp1

no pmipv6-profile
To delete the PMIPv6 profile, use the following command.
ruckus(config)# no pmipv6-profile 
Syntax Description
This command uses the following syntax:
name: PMIPv6 profile name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no pmipv6-profile pmip34

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

193

Configuration Commands
no radius-service

no radius-service
To delete a RADIUS service configuration, use the following command.
ruckus(config)# no radius-service 
Syntax Description
This command uses the following syntax:
name: Name of the RADIUS service to be deleted.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no radius-service rad87

no report
To delete reports, use the following command.
ruckus(config)# no report 
Syntax Description
This command uses the following syntax:
report-title: Report to be deleted
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no report scg-dns-report

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

194

Configuration Commands
no rks-gre

no rks-gre
To delete reports, use the following command.
ruckus(config)# no rks-gre 
Syntax Description
This command uses the following syntax:
name: Ruckus GRE tunnel profile name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no rks-gre GRE1

no role
To delete the role, use the following command.
ruckus(config)# no role 
Syntax Description
This command uses the following syntax:
name: Name of the role to be deleted
Default
This command has no default settings.
Command Mode
Config
Example
ruckus(config)# no role rm34

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

195

Configuration Commands
no snmp-trap

no snmp-trap
To disable SNMP trap configuration, use the following command.
ruckus(config)# no snmp-trap
Syntax Description
This command has no arguments or keywords.
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no snmp-trap 113

no snmp-v2-community
To delete SNMPv2 community, use the following command.
ruckus(config)# no snmp-v2-community 
Syntax Description
This command uses the following syntax:
community: Community name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no snmp-v2-community cm2

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

196

Configuration Commands
no snmp-v3-user

no snmp-v3-user
To delete SNMPv3 user configuration, use the following command.
ruckus(config)# no snmp-v3-user 
Syntax Description
This command uses the following syntax:
user: User name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no snmp-v3-user ud11

no soft-gre
To delete the oft GRE tunnel profile, use the following command.
ruckus(config)# no soft-gre 
Syntax Description
This command uses the following syntax:
name: Soft GRE tunnel profile name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no soft-gre GRE1

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

197

Configuration Commands
no subpackages

no subpackages
To delete subscription packages, use the following command.
ruckus(config)# no subpackages 
Syntax Description
This command uses the following syntax:
name: Name of the subscription package
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no subpackages sub1
Do you want to continue to delete (or input 'no' to cancel)? [yes/no]

no ttg-pdg-profile
To delete TTG+PDG profile configurations, use the following command.
ruckus(config)# no ttg-pdg-profile 
Syntax Description
This command uses the following syntax:
name: TTG PDG profile name
Default
This command has no default settings.
Command Mode
Config
Example
ruckus(config)# no ttg-pdg-profile ttg34

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

198

Configuration Commands
no user-agent-blacklist

no user-agent-blacklist
To delete the user agent blacklisted, use the following command.
ruckus(config)# no user-agent-blacklist 
Syntax Description
This command uses the following syntax:
name: Name of the user agent which is blacklisted
Default
This command has no default settings.
Command Mode
Config
Example
ruckus(config)# no user-agent-blacklist userb1
Do you want to continue to delete (or input 'no' to cancel)? [yes/no]

no user-role
To delete all users except the default user, use the following command.
ruckus(config)# no user-role 
Syntax Description
This command uses the following syntax:
name: Name of the user role
Default
This command has no default settings.
Command Mode
Config
Example
ruckus(config)# no user-role userr1
Do you want to continue to delete (or input 'no' to cancel)? [yes/no]

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

199

Configuration Commands
no user-traffic-profile

no user-traffic-profile
To delete all users traffic profiles, use the following command.
ruckus(config)# no user-traffic-profile 
Syntax Description
This command uses the following syntax:
name: Name of the user traffic profile
Default
This command has no default settings.
Command Mode
Config
Example
ruckus(config)# no user-traffic-profile userp1
Do you want to continue to delete (or input 'no' to cancel)? [yes/no]

no zone
To delete all AP zones, expect staging zone use the following command.
ruckus(config)# no zone
Syntax Description
This command uses the following syntax:
 ap 
: AP zone name
ap: Deletes an AP of a specific AP zone
: AP MAC address
 wlan 
: AP zone name
wlan: Deletes WLANs of a specific AP zone
: WLAN name
 aaa 
: AP zone name
aaa: Delete AAA servers of a specific AP zone

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

200

Configuration Commands
no zone

: AAA server name
 hotspot 
: AP zone name
hotspot: Delete WISPr (Hotspot) of a specific AP zone
: WISPr (Hotspot) name
 hotspot-v2-sp 
: AP zone name
hotspot-v2-sp: Delete Hotspot 2.0 Service Provider Profiles of a specific AP
Zone
: Service Provider profile name
 hotspot-v2-op 
: AP zone name
hotspot-v2-op: Delete Hotspot 2.0 Operator Profiles of a specific AP Zone
: Operator profile name
 ap-group 
: AP zone name
ap-group: Delete AP Groups of a specific AP Zone
: AP Group name
 wlan-group 
: AP zone name
wlan-group: Delete WLAN Groups of a specific AP Zone
: WLAN Group name
 ap-register-rule 
: AP zone name
ap-register-rule: Delete AP Registration Rules of a specific AP Zone
: AP Registration Rule
 cluster-switch-over
: AP zone name
cluster-switch-over: Disables the cluster switchover

: AP zone name

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

201

Configuration Commands
northbound-authtype

Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# no zone induszd3

northbound-authtype
Sets the RADIUS authentication type to northbound portal interface, use the
following command.
ruckus(config)# northbound-authtype
Syntax Description
This command uses the following syntax:
: RADIUS authentication type
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# northbound-authtype PAP
SCG30(config)# northbound-authtype CHAP

northbound-portal
Sets the northbound portal configuration, use the following command.
ruckus(config)# northbound-portal 
Syntax Description
This command uses the following syntax:
password: Password for the northbound portal interface

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

202

Configuration Commands
ntp-server

Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# northbound-portal ruckus1!

ntp-server
Sets the NTP server configuration, use the following command.
ruckus(config)# ntp-server 
Syntax Description
This command uses the following syntax:
ntp-server: NTP server IP/domain name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# ntp-server host 172.19.13.53

pmipv6-profile
Sets the NTP server configuration, use the following command.
ruckus(config)# pmipv6-profile > |  | > | 
Syntax Description
This command uses the following syntax:
global interval 
global: Global LMA and MAG options
interval: Set the LMA keep-alive interval
: LMA keep-alive interval value, which is between 5 and 60

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

203

Configuration Commands
pmipv6-profile

global retry 
global: Global LMA and MAG options
retry: Set the LMA keep-alive retries
: LMA keep-alive retries value, which is between 1 and 10
global refresh-time 
global: Global LMA and MAG options
refresh-time: Binding refresh time
: Binding refresh time value, which is between 4 and 65535

: PMIPv6 profile name
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# pmipv6-profile global refresh-time 120

Related Commands
Table 71 lists the related pmipv6 configuration commands.
.

Table 71. Commands related to ruckus(config-pmipv6-profile).
Syntax and Type

Parameters (if any)

Description

ruckus(config-pmipv6-profile)# apn

: APN Name

Sets the APN value.



Sets the description length
between 1 and 128.

 [ secondary |
primary ]

Sets the LMA IP address.

Type: Privileged
ruckus(config-pmipv6-profile)#
description
Type: Privileged
ruckus(config-pmipv6-profile)# lma-ip
Type: Privileged

ruckus(config-pmipv6-profile)# mac48 [ hexadecimal | decimal ] Sets the Mac48 format.
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

204

Configuration Commands
q-in-q-ethertype

Table 71. Commands related to ruckus(config-pmipv6-profile).
Syntax and Type

Parameters (if any)

Description

ruckus(config-pmipv6-profile)# mn-id

[ mac48 | nai ]

Sets the MN-ID options, which
are:

Type: Privileged

• mac48: Mac48 @ APN type
• nai: NAI from authentication
type
ruckus(config-pmipv6-profile)# no

no lma-ip 

Disables the LMA IP address.

Type: Privileged

q-in-q-ethertype
To change Q-in-Q ether type, use the following command.
ruckus(config)# q-in-q-ethertype <8100> | <9100> | <9200> | <88a8>
Syntax Description
This command uses the following syntax:
[8100 | 9100 | 9200 | 88a8]
8100: 0x8100
9100: 0x9100
9200: 0x9200
88a8: 0x88a8
Default
This command has no default settings.
Command Mode
Config
Example
SCG30(config)# q-in-q-ethertype 9200

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

205

Configuration Commands
radius-service

radius-service
Sets the RADIUS service configurations, use the following command.
ruckus(config)# radius-service 
Syntax Description
This command uses the following syntax:

name: Name of the RADIUS server
Default
This command has no default settings.

Command Mode
Config
Example
SCG30(config)# radius-service rad01

Related Commands
Table 72 lists the related radius-service configuration commands.
Table 72. Commands related to ruckus(config-radius-service)
Syntax and Type

Parameters (if any)

Description

ruckus(config-radius-service)#
backup

ip : Set the IP
address of secondary
RADIUS server

Enables backup RADIUS
support and related settings.

Type: Privileged

port : Set the port
of secondary RADIUS
server
shared-secret : Set the shared
secret of secondary
RADIUS server
ruckus(config-radius-service)#
description



Sets the description of the
RADIUS server created.

Type: Privileged
ruckus(config-radius-service)# do

Executes the do command.

Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

206

Configuration Commands
radius-service

Table 72. Commands related to ruckus(config-radius-service)
Syntax and Type

Parameters (if any)

ruckus(config-radius-service)# end

Description

Type: Privileged

Ends the current configuration
session and returns to privileged
EXEC mode.

ruckus(config-radius-service)# exit

Exits from the EXEC.

Type: Privileged
ruckus(config-radius-service)# help

Displays the help.

Type: Privileged
ruckus(config-radius-service)# ip



Type: Privileged

Sets the IP addresses of the
primary RADIUS server.

ruckus(config-radius-service)# max- 
retry

Sets the maximum number of
retries.

Type: Privileged
ruckus(config-radius-service)# mor

[ <0 or 10-4096> ]

Sets the maximum outstanding
requests per server.

ruckus(config-radius-service)# no

backup

Disables various options.

Type: Privileged

no-response-fail

ruckus(config-radius-service)# port



Sets the port addresses of the
primary RADIUS server.



Sets the reconnect time to the
primary RADIUS server.



Sets the request timeout in
seconds.



Sets the response window in
seconds.



Sets the revive interval period in
seconds.

Type: Privileged

Type: Privileged
ruckus(config-radius-service)#
reconnect-primary
Type: Privileged
ruckus(config-radius-service)#
request-timeout
Type: Privileged
ruckus(config-radius-service)#
response-window
Type: Privileged
ruckus(config-radius-service)#
revive-interval
Type: Privileged

SmartCell Gateway 200 Command Line Interface Reference Guide for RuckOS 3.0, 800-70675-001 Rev A

207

Configuration Commands
report

Table 72. Commands related to ruckus(config-radius-service)
Syntax and Type

Parameters (if any)

Description

ruckus(config-radius-service)#
sanity-timer



Sets the sanity timer in seconds.



Sets the shared secret of the
primary RADIUS server.




Tests the RADIUS server based
on the user credentials.

[ <10-90 %> ]

Sets the percentage of
maximum number of
outstanding requests.

[ radius | radius-acct ]

Sets the RADIUS type and
RADIUS accounting type.



Sets the zombie period in
seconds.

Type: Privileged
ruckus(config-radius-service)#
shared-secret
Type: Privileged
ruckus(config-radius-service)# test
Type: Privileged
ruckus(config-radius-service)#
threshold
Type: Privileged
ruckus(config-radius-service)# type
Type: Privileged
ruckus(config-radius-service)#
zombie-period
Type: Privileged

report
Sets the report configurations, use the following command.
ruckus(config)# report