S and C Electric TSIICONTRL2 TripSaver Service Center Configurable Controller2 User Manual Form974 indd

Download:
Mirror Download [FCC.gov]
Document ID	3162867
Application ID	EpN8speiI3Rlyl4fOt7rWg==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	138.29kB (1728607 bits)
Date Submitted	2016-10-13 00:00:00
Date Available	2016-10-13 00:00:00
Creation Date	2016-10-04 14:46:49
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2016-10-04 15:22:06
Document Title	Form974.indd
Document Creator	Adobe InDesign CC 2015 (Macintosh)

S&C TripSaver® II Cutout-Mounted Recloser
Controller Module
and USB Dongle User Guide
Table of Contents
Section
Page
Introduction
Qualified Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Read this Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Proper Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Retain this Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hardware
Contents of TripSaver II Controller Module . . . . . . . . . . . 4
S&C Form 974 (10-16)
© S&C Electric Company 2016, all rights reserved
Section
Page
Software
Download Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Install Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Launch Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connect to a TripSaver II Controller Module
and USB Dongle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Introduction
Qualified Persons
WARNING
The equipment covered by this publication must be installed, operated, and maintained by
qualified persons who are knowledgeable in the installation, operation, and maintenance
of radios in electric power distribution equipment, along with the associated hazards. A
qualified person is a radio technician who is qualified to install transmission-power-limited
radio equipment per FCC Part 15 and who is trained and competent in:
• The skills and techniques necessary to distinguish exposed live parts from nonlive
parts of electrical equipment
• The skills and techniques necessary to determine the proper approach distances
corresponding to the voltages to which the qualified person will be exposed
• The proper use of the special precautionary techniques, personal protective
equipment, insulating and shielding materials, and insulated tools for working on or
near exposed energized parts of electrical equipment
These instructions are intended only for such qualified persons. They are not intended
to be a substitute for adequate training and experience in safety procedures for this type
of equipment.
Read this
Form
Proper Application
NOTICE
Thoroughly and carefully read this form before programming, operating, or maintaining
your S&C TripSaver II Controller Module and USB Dongle User Guide.
WARNING
The equipment in this publication must be selected for a specific application. The
application must be within the ratings furnished for the selected equipment.
Retain this
Form
2   S&C Form 974
This form should be available for reference wherever a Controller Module and USB
Dongle User Guide is to be used. Retain this form in a location where you can easily
retrieve and refer to it.
Introduction
Regulatory
Information
This device complies with part 15 of the FCC rules and regulations regarding unlicensed
transmissions. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference and (2) this device must accept any interference.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil est conforme aux normes Industry Canada exemptes de licence RSS
standard(s). Son fonctionnement est soumis aux deux conditions suivantes : (1) cet
appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute
interférence, y compris les interférences susceptibles de provoquer un fonctionnement
indésirable.
IMPORTANT! Changes or modifications not expressly approved by S & C Electric Company
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
CAN ICES-3 (A)/NMB-3(A)
TripSaverII Controller Details
Model number: TSII-CONTRL2
Model number: TSII-CONTRL3
FCC ID: U3D-TSIICONTRL2
TripSaverII USB Dongle Details
Model Number: TSII-DONGLE
FCC ID: RUN1322C-USB
IC: 6744A-1322XUSB
S&C Form 974   3
Hardware
Contents of
TripSaver II
Controller Module
Ac Adapter
Power Outlet Plug Adapters
USB Dongle
Contoller Module
This Manual
S&C Form 974
Software
Download Software
IntelliLink® TripSaver II Controller Module Setup Software is available for download only
to customers who have purchased the module. For each controller module purchased,
the user is entitled to install and use S&C IntelliLink TripSaver II Controller Module
Setup Software on no more than two computers at a time. The latest software release is
posted on the S&C Automation Customer Support Portal at www.sandc.com/support/
automation-customer-support-portal.asp. You will need a username and password to
log in to the portal. If you are a new S&C customer, complete the form in the lower section
of the webpage and a new username and password will be sent to you. If you already have
a password, click the Log-In To Secure Site button. Enter the username and password
to log into the portal. Download the installer ILTS Setup-1.165.15712.0 from the portal.
Install Software
Double-click the downloaded installer file and follow the on-screen instructions. The
installer will automatically install the Microsoft .NET framework onto your computer if
the required .NET version is missing. You will need administrative privileges to finish the
installation.
Launch Software
Click the green ILTS icon on your desktop or in the Start menu to launch the TripSaver
II Controller Module Setup Software. A warning screen will be displayed right after the
software is launched. Read the message carefully and understand the warning.
Proceed by clicking the green I have read and understand the above warning button.
Once you launch the software, you can configure and save settings under the Standalone (Offline) mode.
S&C Form 974   5
Connect to a TripSaver II Controller Module
To connect to a TripSaver II Controller Module to apply
your new settings, follow these steps.
Step 1
Install USB Transceiver
A USB transceiver must be installed on your computer to
communicate with a TripSaver II Controller Module. Insert
the USB transceiver into any USB port on your computer.
See Figure 1. The installation process should be automatic.
Note: You do not need the USB transceiver to be installed to
install the software and to run the software in Standalone
(offline) mode.
Step 2
Assemble Power Supply and Power Up TripSaver II
Controller Module
Figure 1. Insert the USB transceiver.
A TripSaver II Controller Module must be powered by the
power module to enable its communication capability.
Complete the following steps before attempting to
communicate with your TripSaver II Controller Module:
(a) Insert the connector from the power module onto the
pins in the TripSaver II Controller Module, as shown in
Figure 2.
(b) Install the proper power outlet plug adapter onto the
AC adapter. See Figure 3.
(c) Plug the ac adapter into a wall outlet. See Figure 4.
Figure 2. Insert the connector from the power module.
Figure 3. Insert power outlet plug adapter.
Figure 4. Plug the adapter into a wall outlet.
S&C Form 974
Connect to a TripSaver II Controller Module
(d) To verify that your TripSaver II Controller Module is
powered up, place a magnet next to the controller
module and observe the LCD screen. See Figure 5. If
the LCD screen begins to scroll, it indicates
the unit has been successfully powered up.
Your setup, at the end of Step 2, should look like the
picture in Figure 5..
Figure 5. Verify module is powered up.
S&C Form 974   7
Connect to a TripSaver II Controller Module
Step 3
Obtain Transceiver ID
A Transceiver ID unique to each TripSaver II Controller
Module is needed to establish communications between
your computer and the device. See Figure 6. The ID consists
of a 32-digit character string in the format of
“0019C900.00020000. _ _ _ _ _ _ _ _ . _ _ _ _ _ _ _ _”.
You must enter the ID in order to communicate with each
TripSaver II Controller Module.
The Transceiver ID is also labelled on the top of the
controller module side attached to each TripSaver II
Controller Module when it leaves S&C Electric Company.
Step 4
Figure 6. The transceiver ID.
Connect to Device
To connect to a TripSaver II Controller Module, select
Connection>Connect to Device from the main menu
or click the Connect to Device icon
in the quick access
toolbar. Make sure that the USB transceiver is already
plugged into your computer.
Enter last 16 digits here
Next, a Transceiver ID Request dialog box will appear.
See Figure 7. Enter the Transceiver ID of the TripSaver II
Controller Module you want to connect to, and click on
the OK button to connect. The first 16 digits of the ID are
pre-typed. You only need to enter the last 16 digits.
During the connection process, a status bar will be
displayed. Wait about ten seconds for the connection
process to finish, or click the Cancel button to cancel the
connection process.
You will be able to see the Status Screen after your
TripSaver II Controller Module is successfully connected.
Now, you can view existing settings, status information, and
event logs of the TripSaver II Controller Module, or apply
new settings to the device.
S&C Form 974
Figure 7. Enter the tranceiver ID number.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Language                        : en-US
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Create Date                     : 2016:10:04 14:46:49-05:00
Modify Date                     : 2016:10:04 15:22:06-05:00
Metadata Date                   : 2016:10:04 15:22:06-05:00
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Version ID                      : 1
Instance ID                     : uuid:e0376442-9e7b-4ee6-abf4-05ff0ed4c7f6
Original Document ID            : adobe:docid:indd:5e627ac3-6e08-11de-b9de-d42728619a65
Document ID                     : xmp.id:008ca7a9-b5b4-4157-915b-ed8b39cd975b
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:2cc05c63-ceaa-46da-a7f5-aa63ab5ee22f
Derived From Document ID        : xmp.did:c0089cd8-f88c-4b0c-9827-85e0fa4c652f
Derived From Original Document ID: adobe:docid:indd:5e627ac3-6e08-11de-b9de-d42728619a65
Derived From Version ID         : 1
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Macintosh)
History Changed                 : /
History When                    : 2016:10:04 14:46:49-05:00
Format                          : application/pdf
Title                           : Form974.indd
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Page Count                      : 8
Creator                         : Adobe InDesign CC 2015 (Macintosh)

EXIF Metadata provided by EXIF.tools