S and C Electric TSIICONTRL2 TripSaver Service Center Configurable Controller2 User Manual Module Integration Instruction
S&C; Electric Company TripSaver Service Center Configurable Controller2 Module Integration Instruction
Contents
- 1. Module Integration Instruction
- 2. Users manual
Module Integration Instruction
6601 North Ridge Boulevard Chicago, Illinois 60626-3997 Telephone (773) 338-1000 Fax (773) 338-3657 Module Integration Instructions To integrate the TSIICONTRL2 module in a host product the following instructions need to be followed Power requirements: When powering the unit from the CT terminals, the maximum input current should not exceed 1.6Arms @50/60 Hz continuously. Note: Once the module is fully charged the CT input terminals will be shorted as a virtue of this design. The charging level can be controlled by software When powering the unit from the SEPIC terminals, the input voltage limits should not exceed 25V (upper limit) or be lower than 5V (lower limit). The module can draw currents as high as 1A. Input voltage polarity is not critical for the proper functionality of the module. The module’s box is metalized and connected to the ground reference of the electronics. Current sensing terminals are floating with respect to the internal grounds (differential input). Special care should be taken to reduce induced noise in the system ( sensor and CT shielding is recommended) Environment requirements: The module is not sealed from the environment point of view. It relies on the host product to provide protection against water entry and condensation. Host equipment is fully tested at all environmental conditions to protect control module residing inside. Communication requirements: This module is designed operate in the presence of interface This module is also designed to coexist with other 2.4GHz products, even multiple modules in the nearby area Input/output signals: This module can take up to 105Arms @50/60Hz input surge current up to 0.5 seconds Grounding requirements: Sensing signals Only the current sensing have a differential input and its input should not exceed +/-10V All other sensing signals are single ended. Drivers: The main two drives can put out voltage in the +/-225V range (peak voltage of the PWM technique) with currents as high as 10A Display: When handling the module, avoid applying any pressure on the LCD Protect the LCD against 380 nm UV wavelengths. 6601 North Ridge Boulevard Chicago, Illinois 60626-3997 Telephone (773) 338-1000 Fax (773) 338-3657 Connections: The module has 4 connectors distributes as follows Signal Name Current sensor input Current sensor input Connector J12/TE Connectivity J12/TE Connectivity Pin CT input terminal CT input terminal J2/TE Connectivity J2/TE Connectivity Driver 1_P Position Sensor Drive 1 N J8/Molex J8/Molex J8/Molex Driver 2 P Driver 2 N J9/Molex J9/Molex J10/TE Connectivity J10/TE Connectivity J10/TE Connectivity J10/TE Connectivity J10/TE Connectivity 13V External Sensor AGND SEPIC input SEPIC input This module is primarily designed to work with S&C’s host products.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : muhammad.tabani Create Date : 2016:07:11 10:00:05-05:00 Modify Date : 2016:07:11 10:00:05-05:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 11.0 (Windows) Format : application/pdf Title : Microsoft Word - TSII Module Integration Instructions.doc Creator : muhammad.tabani Document ID : uuid:19574dfa-4d9c-44d4-8fe8-8d599749719d Instance ID : uuid:38fff24c-130a-4dfc-8e9d-a5680874b1a4 Page Count : 2EXIF Metadata provided by EXIF.tools