SAT AMERICA LI102W BARCODE SCANNER User Manual user manual

SAT AMERICA INC BARCODE SCANNER user manual

user_manual

Download: SAT AMERICA LI102W BARCODE SCANNER User Manual user manual
Mirror Download [FCC.gov]SAT AMERICA LI102W BARCODE SCANNER User Manual user manual
Document ID4044532
Application ID6yDp2X44vChZDZ1K3gqrqQ==
Document Descriptionuser_manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize102.93kB (1286575 bits)
Date Submitted2018-10-22 00:00:00
Date Available2018-10-22 00:00:00
Creation Date2018-09-11 10:57:29
Producing SoftwareCorel PDF Engine Version 17.1.0.572
Document Lastmod2018-09-11 10:57:29
Document Title1230105001 一维无线条码扫描器带底座简易说明V2.0（英文）.cdr
Document CreatorCorelDRAW X7
Document Author: Administrator

Model No.: SAT LI102W
1D Barcode Scanner
1 Scanner overview
LED Indicator
Buzzar
Quick Start Guide
3 Cable connection guide
4 Scanning method and distance
（1）USB Data cable
Scanning window
Scanner
Trigger Bu on
1D
Cradle LED
Indicator
Cardle
2 Cable plug&Unplug
Contents:● Barcode Scanner ●Cradle
● Quick Start Guide
● USB / RS232 Cable
● Power Adapter (Rs232 only )
No. :1230105001
5 Charging method
①
（2）RS232 Data cable
v2.0
① Plug as picture above
Pairing Guide
Transmitter(Scanner)
Method
Working mode：
②
Following working mode can be set directly.
t di
st
Correct
Wrong
121311113
121311113
5CM
Inventory mode setting
Following working mode can be set directly.
*Real- me mode
Upload data
Inventory mode
Data sum
Cache mode
Clear Data
Note:
Pair in one step
bes
～1
NOTE: LED beam should be full coveraged
on the bar code
② Press the buckle click,
then pull out the cable
First step: Insert the cradle as above picture. the green light
of the cradle will con nue（ on not able to pair when
green light flashing.）
Second step: A er insert the cradle , it must be scan the
below bar code within 20s
The
e6
anc
Real me mode: Scan and transmit data will automa cally lost
if upload failed.
Cache mode: Same as real me mode if connec on normal.
Scan bar codes will be automa cally restore if connec on
failed. Will upload one by one if connec on return as normal.
Inventory Mode : Scanning bar codes will be restored without
upload.
Will upload once scan “Upload data”barcode.
Will clear once scan“Clear data”.
Will check sum once scan”Data sum” .
Upload data: Bar code data will transmit to terminal once
scan this bar code.
Date sum: Scan “Data sum”bar code to check the scanner
restore data sum.
Clear data: Scan“Clear data” and clear all the restore
data in scanner
Wierless Settings
This part is valid for wireless se ngs only
①Defaults Parameter
The default se ng allows the scanner to be restored
to the factory se ng state.
Set up process：
③ Suffix
④Sleep Time Setting
Set up process：
The sleep me means the me between the last opera on move and
auto turn off the scanner. User able to scan the corresponding bar code
of the sleep me which is needed to accomplish the sleep me se ng.
❶Scan the bar code of“Enter Setting”.
Set up process：
❶Scan the bar code of“Sleep Time”.
Enter Se ng
❷Scan the bar code of "Custom Suffix".
Sleep Time
❶Scan the bar code of“Enter Setting”.
Enter Se ng
❷Scan the bar code of “Restore Defaults”.
❷Scan one of the bar code below as sleep me.
Custom Suffix
❸Scan one of bar code below as suffix
20S
Restore Defaults
❸Scan the bar code of "Exit and Save".
Configura on method: Scan the func on bar code directly.
Enable Numeric Keypad
Green light on
Red light blinks
Green light blinks once
Green light blinks twice
Red light on
Blue light on
Green light on
Green light blinking
Descrip on
Power on/ Working normally
Pairing match
Upload successfully
Upload failed
Low ba ery
Charging normal
Charging complete
Pairing unsuccessful
3min
*0x0D （CR）
Cradle
5min
②Numeric Keypad
LED Status
Scanner
60s
None
Exit and Save
Light
0x0A （LF）
15min
TAB
❹Scan the bar code of “Exit and Save”.
Exit and Save
30min
None sleep
❸Scan the bar code of “Exit and Save”.
Green light blinks 30s
Red light on
Green light blinks once
Green light on
Pairing state
USB iden fy failed
Uploaded successfully
Working normally
Exit and Save
*Disable Numeric Keypad
Decode Settings
This part is valid for decode se ngs only
Se ng Step
Scan the bar code of “Enter se ng”
Enter Se ng
① Trigger Mode
Single decode : When a bar code has been decoded, the reader will
be turned off. The reader must be triggered again to read another
label.
③ Dalay for repeating to
read the same barcode
Con nuous decode : The reader will produce as much data as it
can decode regardless whether it is the same or not. This mode is
mainly used for demonstra on and diagnosis.
*Single Read
500ms（F0205）
1000ms（F0210）
Con nuous Read
Scan the func on bar codes
② Reading Mode
2000ms（F0220）
④ Auto trigger（optional）
Disable repeat read（F0100）
Scan the bar code of “Exit and Save”
Exit and Save
Disable auto trigger（H0000）
*Enable repeat read （F0101）
Mul ple read（F0102）
Mul ple read: The same label can only be decoded again a er
the label has not been detected for a number of
scans. This mode can only be programmed in
Con nuous read trigger mode.
* Enable auto trigger（H0001）
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
Warning: Changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Profile CMM Type                : Linotronic
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : Hewlett-Packard
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : Hewlett-Packard
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 2
Create Date                     : 2018:09:11 10:57:29+08:00
Modify Date                     : 2018:09:11 10:57:29+08:00
Producer                        : Corel PDF Engine Version 17.1.0.572
Author                          : Administrator
Creator                         : CorelDRAW X7
Title                           : 1230105001 一维无线条码扫描器带底座简易说明V2.0（英文）.cdr
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2ARCJ-LI102W

Navigation menu