SDI Technologies IBT372 Waterproof & Shockproof Wireless Stereo Speaker User Manual iBT373 QSG

SDI Technologies Inc. Waterproof & Shockproof Wireless Stereo Speaker iBT373 QSG

Contents

User Manual-2

QUICK START GUIDE
Contact Us: 1•800•288 • 2792
For full waranty and full instructions
visit: www.ihome.com/support
Speakerphone
» The speaker must be on and connected with a paired Bluetooth device to recieve calls
» When a call is received, playing music is muted to hear the ring tone. Press the
Bluetooth/Speakerphone Button to answer call. For call waiting function, use
phone controls on your device.
» Press the Bluetooth/Speakerphone Button again to end call and resume previous function.
iBT373
FCC ID: EMOIBT372
IC: 986B-IBT372
FCC Information
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
• Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3 (B)/NMB-3(B)
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
le dispositif a été évalué à satisfaire l'exigence générale de l'exposition aux rf.
l'appareil peut être utilisé dans des conditions d'exposition portatif sans restriction.
iBT373-170105-A (EN) Printed in China
QUICK START GUIDE CHARGE UNIT BEFORE
USE - ABOUT 5 HOURS
In the Box » iBT373 speaker » USB charging cable » Carry Strap
» Connect the micro-USB plug on the included charging
cable to the USB Charging jack on the speaker.
»
USB AC adaptor
(not included)
Contact Us: 1•800•288 • 2792
Color Changing Modes
» Press and hold the Power Button for 2 seconds to power on iBT373
» Press the Color Mode Button to cycle through these modes:
Slow Fade Fast Change Favorite Color Pulse to Music Preset Pulsing O
For full waranty and full instructions
visit: www.ihome.com/support
iBT373 QSG
Size: 280W x 160H (mm)
Folded size: 140W x 160H
material: 260gsm2 art card, 2C + 1C
Date: Jan 10, 2016
FRONT
BACK
This device uses an internal non-replaceable rechargeable lithium-ion battery that should
last the lifetime of the device. If you suspect your battery may be dead, try charging it for
an extended period of time and try resetting the unit. If this fails, contact Customer
Service at 1-800-288-2792.
WARNING/DISPOSAL OF UNIT
Do NOT attempt to change the battery. Doing so will void the warranty and could cause
injury and damage to your device.
To dispose of the unit, follow the instructions below:
• Never dispose of used batteries/electronics with ordinary solid wastes, since they contain
toxic substances.
• Always dispose of used batteries/electronics in accordance with the prevailing community
regulations.
• Many electronics retailers now recycle batteries and other electronic components at no
charge.
GENERAL BATTERY PRECAUTIONS
• Never use or charge a battery if it appears to be leaking, discolored, deformed, or in any
way abnormal.
• Never disassemble the unit or attempt to remove battery as that could cause leakage of
alkaline solution or other electrolytic substances.
• Avoid charging a rechargeable battery when the temperature is not within 5°C - 35° C (41°
- 95° Fahrenheit).
• Never expose a battery to any liquid.
• Never expose a battery to excessive heat such as direct sunlight or fire. Never use a
battery pack in an unventilated vehicle where excessive internal temperatures may be
encountered.
• Always keep batteries out of the reach of infants and small children.
Internal Rechargeable Lithium-ion Battery
Aux-In
Waterproof Operation
» To play aux audio, connect a standard audio cable (not included) to the headphone jack
of your audio device and connect the other end to the aux-in jack on iBT373.
» Press and hold the Power Button for 2 seconds on the unit to turn it on.
» Power on the aux audio device and use the controls on the device to play or pause audio, and to
navigate tracks. Make sure to pause any connected Bluetooth device to hear aux audio.
» Press the or buttons to adjust the system volume. You can also adjust volume on your device.
Charging Status indicator
Solid red = charging Red LED o = fully charged Flashing red = low battery
Bluetooth: Pairing & Playing
» Make your device “discoverable” by turning on Bluetooth mode
» Press and hold the Power Button for 2 seconds to power on iBT373
» Select “iHome iBT372” on your device’s Bluetooth
menu to complete pairing
» Press the Play/Pause Button to play and pause audio from
your Bluetooth device. Navigate tracks from your device.
» Use the and buttons to control iBT373 volume
» The first time the unit is powered
on it will enter auto-pairing mode
» Power on speaker
» Press and hold the Bluetooth/
Speakerphone Button for 2 seconds
Pairing the First Time Manual Pairing
iHome
iBT373
-OR-
» For proper waterproof operation, make sure the waterproof cover on the right side of the unit is
completely flush with the unit by pressing along the entire edge of the cover until it is completely
and securely in place.
Voice Commands
» NOTE: The unit must be powered on and linked to a Bluetooth phone to use voice commands.
» Press and hold the Play/Pause/Voice Command Button to access the voice command protocol
associated with your device’s operating system (Siri for iOS devices, “OK, Google” for Android
devices, etc.)
PMS7469C
Model: iBT373
Color Changing Rechargeable
Bluetooth Speaker with Speakerphone
Model: iBT373
Color Changing Rechargeable
Bluetooth Speaker with Speakerphone
water
tight
not
water
tight
Connect USB cable to USB port and the other end to your
device to charge.

Navigation menu