SEBINE Technology WTH WTH User Manual

SEBINE Technology, Inc. WTH Users Manual

Users Manual

WTHWTH_ENG_20120201.hwp 1 WTH System ManualVer 1.00SEBINE Technology, Inc.
WTHWTH_ENG_20120201.hwp 2CONTENTS1. Summary1.1 Product Introduction1.2 Specification2. Device Summary 2.1 Power Supply2.2 USB communication connection2.3 LED Indicator3. Wi-Fi wireless communication environmental setting3.1 Wireless LAN(AP) setting3.2 WTH settingAppendix 1. WTH USB Driver InstallationAppendix 2. WTH UDP Server InstallationAppendix 3. Document HistoryAppendix 4. Dimension
WTHWTH_ENG_20120201.hwp 41. Outline1.1 Product IntroductionWTH is a sensor to detect temperature and humidity wirelessly by using ISM 2.4GHz frequency bandwidth. WTH transmits the temperature. humidity, and smoke detection data at each user set-up period via UDP communication method. Users can configure their own setting for WTH via serial communication program. ※ Keep the filter of a sensor clean.
WTHWTH_ENG_20120201.hwp 51.1.1 Product Application ExamplesProduct Application Examples1.1.2 Product Application ArealDepartment Store, Public Office, GymnasiumlMuseum, School, Manufacturing FactorylOffice Building, Movie Theater, Shipbuilding/Marine1.1.3 Product PackageWTH main body, USB cable, User manuel, Utility CD
WTHWTH_ENG_20120201.hwp 61.2 SpecificationItem Specification Name WTH Dimension 110mm(L)×80mm(W)×33mm(H) Housing ABS Weight 300g (w/o Battery, Antenna) Power Supply AA size 3.6Volt LITHIUM BATTERY 1EA or 2EA Current Consumption Tx 190mA, Rx 140mA (@3.6Vdc) Operating Temperature -40℃ ~ +85℃ RF Features• Frequency : 2412 ~ 2472 MHz• Standard Supported: IEEE 802.11b• Transmitter Power : Max. 7mW• Modulation : IEEE 802.11b : DSSS : 1Mb/s and 2Mb/s IEEE 802.11b : CCK : 5.5Mb/s and 11Mb/s• Channels: Europe – 13 channels USA – 11 channels Performance • RF Data Rate: 1Mb/s to 11Mbps I/O Interface • USB ConnectorAntennaInterface• SMA(Female, Reverse)• Impedance 50ΩSensor Temperature/Humidity• Accuracy Humidity : ±3.0 Temperature : ±0.4 @℃WTH Specification
WTHWTH_ENG_20120201.hwp 72. Device SummaryWTH inside2.1 Power SupplyWTH operates using on or two AA size 3.6Volt LITHIUM BATTERIES. Be careful with battery orientation. 2.2 USB communication connectionTo use WTH, proper setting is necessary for wireless environment to be installed. For setting, connect PC and WTH using USB cable provided in the package. For detailed settings after USB communication connection, see section 3.2. 2.3 LED IndicatorLED turns on during operation when serially connected battery power drops below 3.4V. The WTH may malfunction under 3.4V so batteries need to be changed.
WTHWTH_ENG_20120201.hwp 83. Wi-Fi wireless communication environmental setting3.1 Wireless LAN(AP) settingTo use WTH, wireless LAN(AP) setting is needed for WTH connection.3.1.1 SSID setting(required)When WTH is connected to wireless LAN(AP), SSID is being searched. Thus, SSID must be set on AP and SSID(network) notification function should be used. 3.1.2 Password disabled setting for AP(required)WTH does not use encrypted method for minimizing the system correct consumption. Thus, set password disabled for AP.3.1.3 DHCP disabled(option)WTH does not use DHCP. Wireless LAN(AP) executes or stops DHCP server setting. 3.1.4 MAC Address registration(option)When password is disabled for wireless LAN(AP), the Mac address of WTH is registered to wireless LAN(AP) so that only the registered Mac Address is permitted. This prevents network overflow.
WTHWTH_ENG_20120201.hwp 93.2 WTH settingTo use WTH, Wi-Fi wireless communication environment setting is necessary. 3.2.1 Connection between WTH and PCTo set the wireless communication environment for WTH, connect PC with WTH using the USB cable provided at product purchase. The connection sequence is shown below. ※ Before connection, install USB driver of WTH.[See Appendix 1. USB driver installation]Step 1. With batter inserted at WTH, set System Power SW OFF.WTH setting - POWER SWStep 2. Connect one port of USB cable to PC, and the other port to WTH.Step 3. Switch Mode Selection SW to USB side.WTH setting - Mode Selection SW
WTHWTH_ENG_20120201.hwp 10Step 4. Execute the serial communication program. ▶ Serial communication program setting- Baud Rate : 115200- Data Bit : 8- Stop Bit : 1- Parity Bit : NoneStep 5. Set the System Power SW of WTH ON. When correctly connected, data are shown on serial communication program shown below.Data output via serial communication program
WTHWTH_ENG_20120201.hwp 113.2.2 Wi-Fi wireless communication environment setting of WTHStep 1. SSID settingInsert the SSID of wireless LAN(AP) to be connected with WTH.▶ Data Format : <SSID>󺊈▶ Example : sebinetech󺊈WTH setting - SSID Input
WTHWTH_ENG_20120201.hwp 12Step 2. Static Configuration of Network Parameters settingInsert the information for WTH for connection to wireless LAN(AP). ▶ Data Format : <Src Address>,<Net-mask>,<Gateway>󺊈▶ Example : 192.168.30.21,255.255.255.0,192.168.0.1󺊈WTH setting - Network Parameters Input
WTHWTH_ENG_20120201.hwp 13Step 3. Static Configuration of DNS settingInsert DNS server info for WTH for connection to wireless LAN(AP). ▶ Data Format : <DNS1 IP>,<DNS2 IP>󺊈▶ Example : 168.126.63.1,168.126.63.2󺊈WTH setting - DNS Server Input
WTHWTH_ENG_20120201.hwp 14Step 4. UDP Clients settingInsert IP and Port number of server to which WTH sends data.▶ Data Format : <Dest-Address>,<Port>󺊈▶ Example : 192.168.0.50,3030󺊈WTH setting - UDP Clients Input
WTHWTH_ENG_20120201.hwp 15Step 5. Period settingInsert a period for WTH to send data.▶ Data Format : <time><time unit>󺊈 ※ <time> must be 2 digit▶ Example : 30s󺊈▶ s : sec m : min h : hourWTH setting - Period Input
WTHWTH_ENG_20120201.hwp 163.2.3 Disconnection between WTH and PC When all settings are done, a message “Please Reboot!!" appears. Serial communication program is terminated. When necessary, device manager removes the device.Step 1. Shut down the serial communication program.Step 2. Set the System Power SW of WTH off.Step 3. Remove the port to WTH at device management and remove USB cable from WTH. Step 4. Set the Mode Selection SW to MCU.3.2.4 WTH UDP Server ExecutionFrom user manual and utility CD in package, run WTH Setup.msi to install the demo server. [Appendix 2. See WTH UDP Server installation guide]3.2.5 Run and check of WTHAfter all settings are done, run the installed WTH UDP Server and set the System Power SW of WTH to ON. If the setting of WTH is correctly done, data appear on demo server as shown below.WTH operation check - demo server
WTHWTH_ENG_20120201.hwp 17Appendix 1. WTH USB Driver Installation1. Run “CP210x_VCP.exe" from user manual and utility CD in package. Install by following the procedure below. Step 1. USB Driver InstallationStep 2. USB Driver Installation
WTHWTH_ENG_20120201.hwp 18Step 3. USB Driver InstallationStep 4. USB Driver Installation - Default folder
WTHWTH_ENG_20120201.hwp 19Step 5. USB Driver InstallationStep 6. USB Driver Installation Complete
WTHWTH_ENG_20120201.hwp 20Step 7. USB Driver Installation - Window Device Manager
WTHWTH_ENG_20120201.hwp 21Appendix 2. WTH UDP Server InstallationRun WTH Setup.msi from user manual and utility CD in package to install WTH UDP Server.Step 1. WTH UDP Server InstallStep 2. WTH UDP Server Install
WTHWTH_ENG_20120201.hwp 22Step 3. WTH UDP Server InstallStep 4. WTH UDP Server Install
WTHWTH_ENG_20120201.hwp 23Step 5. WTH UDP Server Install
WTHWTH_ENG_20120201.hwp 24Appendix 3. Document InformationVersion H/W Version Date Changes1.0 WTH-GS-SMK Ver1.2 SMK-NIS Ver1.0 2011.08.30 Initial Release Version
WTHWTH_ENG_20120201.hwp 25Appendix 4. Dimension
WTHWTH_ENG_20120201.hwp 26SEBINE Technology, Inc.Homepage : www.sebinetech.comE-mail : tech@sebinetech.comRN 302, Daedeok Radio Engineering Center, 694, Tamnip-dong, Yuseong-gu, Daejeon, Korea 305-510Tel : 82-42-935-2084, 2085Fax : 82-42-935-2088

Navigation menu