SEBINE Technology WTH WTH User Manual

SEBINE Technology, Inc. WTH Users Manual

Users Manual

Download: SEBINE Technology WTH WTH User Manual
Mirror Download [FCC.gov]SEBINE Technology WTH WTH User Manual
Document ID1630038
Application IDT5V5ObJDQi0E6cywEOf0Yw==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize229.53kB (2869180 bits)
Date Submitted2012-02-02 00:00:00
Date Available2012-02-02 00:00:00
Creation Date2012-02-01 19:43:44
Producing SoftwareezPDF Builder 2006
Document Lastmod2012-02-01 13:58:10
Document TitleUsers Manual
Document CreatorezPDF Builder 2006

WTH
WTH
System Manual
Ver 1.00
SEBINE Technology, Inc.
WTH_ENG_20120201.hwp
WTH
CONTENTS
1. Summary
1.1 Product Introduction
1.2 Specification
2. Device Summary
2.1 Power Supply
2.2 USB communication connection
2.3 LED Indicator
3. Wi-Fi wireless communication environmental setting
3.1 Wireless LAN(AP) setting
3.2 WTH setting
Appendix 1. WTH USB Driver Installation
Appendix 2. WTH UDP Server Installation
Appendix 3. Document History
Appendix 4. Dimension
WTH_ENG_20120201.hwp
WTH
1. Outline
1.1 Product Introduction
WTH is a sensor to detect temperature and humidity wirelessly by using
ISM 2.4GHz frequency bandwidth. WTH transmits the temperature. humidity, and
smoke detection data at each user set-up period via UDP communication method.
Users can configure their own setting for WTH via serial communication program.
※ Keep the filter of a sensor clean.
WTH_ENG_20120201.hwp
WTH
1.1.1 Product Application Examples
Product Application Examples
1.1.2 Product Application Area
l Department Store, Public Office, Gymnasium
l Museum, School, Manufacturing Factory
l Office Building, Movie Theater, Shipbuilding/Marine
1.1.3 Product Package
WTH main body, USB cable, User manuel, Utility CD
WTH_ENG_20120201.hwp
WTH
1.2 Specification
Item
Specification
Name
WTH
Dimension
110mm(L)×80mm(W)×33mm(H)
Housing
ABS
Weight
300g (w/o Battery, Antenna)
Power Supply
Current
AA size 3.6Volt LITHIUM BATTERY 1EA or 2EA
Consumption
Operating
Temperature
Tx 190mA, Rx 140mA (@3.6Vdc)
-40℃ ~ +85℃
• Frequency : 2412 ~ 2472 MHz
• Standard Supported: IEEE 802.11b
• Transmitter Power : Max. 7mW
RF Features
• Modulation : IEEE 802.11b : DSSS : 1Mb/s and 2Mb/s
IEEE 802.11b : CCK : 5.5Mb/s and 11Mb/s
• Channels: Europe – 13 channels
USA
Performance
I/O
Interface
– 11 channels
• RF Data Rate: 1Mb/s to 11Mbps
• USB Connector
Antenna
• SMA(Female, Reverse)
Interface
• Impedance 50Ω
Sensor
Temperature • Accuracy
/Humidity
Humidity : ±3.0
Temperature : ±0.4 @℃
WTH Specification
WTH_ENG_20120201.hwp
WTH
2. Device Summary
WTH inside
2.1 Power Supply
WTH operates using on or two AA size 3.6Volt LITHIUM BATTERIES. Be careful
with battery orientation.
2.2 USB communication connection
To use WTH, proper setting is necessary for wireless environment to be installed.
For setting, connect PC and WTH using USB cable provided in the package. For
detailed settings after USB communication connection, see section 3.2.
2.3 LED Indicator
LED turns on during operation when serially connected battery power drops below
3.4V. The WTH may malfunction under 3.4V so batteries need to be changed.
WTH_ENG_20120201.hwp
WTH
3. Wi-Fi wireless communication environmental setting
3.1 Wireless LAN(AP) setting
To use WTH, wireless LAN(AP) setting is needed for WTH connection.
3.1.1 SSID setting(required)
When WTH is connected to wireless LAN(AP), SSID is being searched.
Thus, SSID must be set on AP and SSID(network) notification function should be
used.
3.1.2 Password disabled setting for AP(required)
WTH does not use encrypted method for minimizing the system correct
consumption. Thus, set password disabled for AP.
3.1.3 DHCP disabled(option)
WTH does not use DHCP. Wireless LAN(AP) executes or stops DHCP
server setting.
3.1.4 MAC Address registration(option)
When password is disabled for wireless LAN(AP), the Mac address of WTH
is registered to wireless LAN(AP) so that only the registered Mac Address is
permitted. This prevents network overflow.
WTH_ENG_20120201.hwp
WTH
3.2 WTH setting
To
use
WTH,
Wi-Fi
wireless
communication
environment
setting
is
necessary.
3.2.1 Connection between WTH and PC
To set the wireless communication environment for WTH, connect PC with
WTH using the USB cable provided at product purchase. The connection sequence
is shown below.
※ Before connection, install USB driver of WTH.[See Appendix 1. USB driver
installation]
Step 1. With batter inserted at WTH, set System Power SW OFF.
WTH setting - POWER SW
Step 2. Connect one port of USB cable to PC, and the other port to WTH.
Step 3. Switch Mode Selection SW to USB side.
WTH setting - Mode Selection SW
WTH_ENG_20120201.hwp
WTH
Step 4. Execute the serial communication program.
▶ Serial communication program setting
- Baud Rate : 115200
- Data Bit : 8
- Stop Bit : 1
- Parity Bit : None
Step 5. Set the System Power SW of WTH ON. When correctly connected,
data are shown on serial communication program shown below.
Data output via serial communication program
WTH_ENG_20120201.hwp
10
WTH
3.2.2 Wi-Fi wireless communication environment setting of WTH
Step 1. SSID setting
Insert the SSID of wireless LAN(AP) to be connected with WTH.
▶ Data Format : 
▶ Example :
sebinetech
WTH setting - SSID Input
WTH_ENG_20120201.hwp
11
WTH
Step 2. Static Configuration of Network Parameters setting
Insert the information for WTH for connection to wireless LAN(AP).
▶ Data Format : ,,
▶ Example : 192.168.30.21,255.255.255.0,192.168.0.1
WTH setting - Network Parameters Input
WTH_ENG_20120201.hwp
12
WTH
Step 3. Static Configuration of DNS setting
Insert DNS server info for WTH for connection to wireless LAN(AP).
▶ Data Format : ,
▶ Example : 168.126.63.1,168.126.63.2
WTH setting - DNS Server Input
WTH_ENG_20120201.hwp
13
WTH
Step 4. UDP Clients setting
Insert IP and Port number of server to which WTH sends data.
▶ Data Format : ,
▶ Example : 192.168.0.50,3030
WTH setting - UDP Clients Input
WTH_ENG_20120201.hwp
14
WTH
Step 5. Period setting
Insert a period for WTH to send data.
▶ Data Format :
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : ezPDF Builder 2006
Creator Tool                    : ezPDF Builder 2006
Modify Date                     : 2012:02:01 13:58:10-08:00
Create Date                     : 2012:02:01 19:43:44+09:00
Metadata Date                   : 2012:02:01 13:58:10-08:00
Document ID                     : uuid:e0854e3c-7487-47b0-ba4376fdd794a0f1
Instance ID                     : uuid:275d4365-2936-4d2e-afe8-a6f67019cd67
Format                          : application/pdf
Has XFA                         : No
Page Count                      : 26
Creator                         : ezPDF Builder 2006
EXIF Metadata provided by EXIF.tools
FCC ID Filing: Y9AWTH

Navigation menu