SOYAL TECHNOLOGY AR-888 Access Controller User Manual

SOYAL TECHNOLOGY CO., LTD. Access Controller User Manual

User_Manual

SOYALACCESS CONTROL SYSTEM®AR-888 V150708ContentsFCC Statement (part15.21,15.105)AR-888 Series InstallationSteps of Ferrite Core Installationwww.soyal.com67A. B. C.D.132(Excluded)(Excluded)In-wallDepth32mm(Excluded)Cable selection: Use AWG 22-24 Shielded Twist Pair to avoid star wiring. Use CAT5 for TCP/IP connection.451Product (US / EU) 2User GuideCN1 CN93Terminal Cables 5EVA foam gasket (US/ EU)4ToolsFlat Head Hex Socket Screw: M3x8Iron bar*2(Inserted into Product)Bottom CoverCN5DuressCN4RS-485CN2WG-InputTake off two Iron bars from the of bottom body A and and mounting plate B. Pull the cables from the square holes of the eva foam gasket and mounting plate. Use a screwdriver to screw the eva foam gasket C and mounting plate B onto the wall with Flat Head Cap Philips Tapping Screws (Excluded, the Installer should prepare before installation. The screws shall not be screwed too tight, or it could lead to the deformation of the mounting plate. Connect the cables to the backside of body A and attach A to B . To x A on B by inserting two Iron bars from the bottom of A + B. Attach the Back Cover D to A. Use the Allen key and screws to assemble the Back Cover onto the body. Hands-off and clear any objects around the 888 (H/K). Turn on the power and LED will light-up and beep will sound. Wait the Touch IC start for 10 sec. to operate.Power DC Input cable 1. Open up the Ferrite Core box 2. To wind the DC in Cable around the Ferrite Core two times3. The close up the Ferrite CoreChanges or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help. US Mounting Hole: 73x48x40mm(HxWxD) / Screw hole pitch : 84mmSuitable for 70X118 1-module ush-mounting box.( Australian, Italy, USA(501E) Standard) EU Mounting Hole: 57x53x40mm(HxWxD) / Screw hole pitch: 60mmSuitable for 86X86 ush-mounting box. (UK, Continental Europe, Germany Standard)Indicators: AR-888(H/K/U)1*Bi-Color Green-Red3*One Color LEDGreen(Optional)White(Stand-By)Red(Optional)AR-PBI-888 1*Bi-Color Green-Red (Exchangeable)
V150708 CN1CN9CN2CN5DC12VCard Present WG-BuzzerWG-GLEDRLEDGNDGNDReservedWG0WG1CN4LA+ (FW Only)LB- (FW Only)13.56MHz 125kHz13.56MHzAR-888 (K/U)SET1 (Format)SET2 (Format)WGRSTWG Reader29 20 GLED Input (Active High) RLED Input (Active High)Basic Commands Wiring Diagramswww.soyal.com Door Lock Wiring Door Sensor Wiring WG Reader Wiring Networking Connection WiringExit program modePIN=0000 (Disable)PIN=0000 (Disable)Add PIN UserM4/M8 Mode13 00001 4321M6 Mode17 4321Add Card+PIN UserSet up Door Relay TimeSet up Door Close TimeTTT: 001~600=1~600 sec. 601~609=0.1~0.9sec. 000=On/ Off (Latch) TTT: 001~600=1~600 sec.Add Card UserEx.: 00001 start user address at 00001 and scanned 50 pcs of card one by one; next time, input 19*00051*00001#User Range: 00000~03000(Please list down each User Address and its Card ID)M4/M8 Mode19 00001 00001M6 Mode (Must set up 17*0000#)22 1Delete Card UserDelete All User CardsReset to Factory Default ValueEx.: 00001 start user address at 0000100005 end user address at 00001Totally 5 user cards will be disabled.User Range: 00000~03000(Delete all cards and parameters)M4/M8 Mode10 00001 900005M6 Mode10 00001 0000529 29 Attach/Present CardOne by One02 00718 015 M4/M8 Mode (4/8 beeps while engtering progrm mode)12 00001 1234M6 Mode (6 beeps) 15 1234CN1CN9CN2CN5CN4DC12V WG0Alarm BuzzerPB GLEDDoor SEN. RLEDCOMN.C.LA+N.O.LB-GNDGNDDuressArmingWG1AR-888 (H)Stand-Alone/NetworkingControllerElectric BoltorMagnetic LockDoor ContactN.C.Electric StrikeAR-888 (K/U)125kHz WG/ABA/RS232 Format(Change by shorted on PCB)Format WG RST/BitsWG 26 Open OpenWG 34 Open ShortRS-232 Short OpenABA-8 Short ShortABA-10 Short OpenAR-888 (K/U)13.56MHz WG/ABA Format(Change by wires connection)Format SET 1 SET 2 NoteWG 26 Open Open HEXWG 34 Open To GND HEXABA-10 To GND Open BCD10ABA-5-5 To GND To GND BCD Exit Button WiringCN1COMN.C.GNDDC12VN.O.Push ButtonAR-PBI888At every 32 units or at every300M connection to add a RS485 Booster.Suggest to connect up to 32 units for each CH of AR-727CMNotice: 032=Node ID of Access Controller032=Virtual 716E Node ID032=Door number(All Range:001~254)009=Node ID of Access Controller Range: 001~254)Set up Node IDEx. Node 32 connected to PC00 032 032 032Ex. Node 9 conected to 716E00 009 Alarm Output 1- Alarm WiringN.C.N.O.COMCTL12VEnable Door Open Too Long Alarm24 064 (Enable)24 000 (Disable)Stop Alarm by Push Button Alarm Output 2- WG Dual Door Control WiringLock 28 064 (Enable)28 128 (Disable)Occupied Alarm Output to support SET Floor/ StopFFFFFFFF0 876543211 16 15 14 13 12 11 10 92 24 23 22 21 20 19 18 173 32 31 30 29 28 27 26 25 Alarm Output 3-Lift Control Wiring B-A+HostAR-401RO16BNode ID 001LiftControllerB-A+AR-321L485ConverterRX24 002 (Enable)24 000 (Disable)Enable Life Control21 UUUUU SFFFFFFFFAssign Floor User (Multi-Floor)S=Set=0~3FFFFFFFF=0 (Disable) / 1 (Enable)Ex. Assign user address 1 to access to 1, 3, 5, 7 oor21*00001*0*01010101#Assign Users (Single Floor)27 UUUUU FFUUUUU=User Address=00000~03000FF=Floor number=1~32123456Enter program modeChange program code Input 6-digit PWD twicePOWER12VDCGNDGLED Input (Active High) RLED Input (Active High) Hall-Effect Sensor (Active Low) Hall-Effect Sensor (Active Low)ExternalRelayAlarm Enable Arming while exit program mode N.C.N.O.COMCTL12VExternalRelayFlush-Mounted Series09 654321654321AR-888(H)Node ID002AR-888(H)Node ID032AR-888(H)Node ID254B-A+B-A+B-A+ HostCH1CH2Each CH up to 8 Nodes Node ID001Multi-DoorControllerConverterAR-321CMAR-727CM

Navigation menu