SOYAL TECHNOLOGY AR-888 Access Controller User Manual

SOYAL TECHNOLOGY CO., LTD. Access Controller User Manual

User_Manual

Download: SOYAL TECHNOLOGY AR-888 Access Controller User Manual
Mirror Download [FCC.gov]SOYAL TECHNOLOGY AR-888 Access Controller User Manual
Document ID2916889
Application IDA979AuG++JKc1UzwVlIuhA==
Document DescriptionUser_Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize25.69kB (321180 bits)
Date Submitted2016-03-01 00:00:00
Date Available2016-03-01 00:00:00
Creation Date2016-01-13 17:57:05
Producing SoftwareAdobe PDF Library 10.0.1
Document Lastmod2016-01-13 17:57:06
Document TitleUser_Manual
Document CreatorAdobe InDesign CS6 (Windows)

SOYAL
®
AR-888
V150708
ACCESS CONTROL SYSTEM
Contents
AR-888 Series
1 Product (US / EU)
2 User Guide
3 Terminal Cables
CN1
CN2
WG-Input
4 Tools
CN4
RS-485
CN5
Flat Head Hex
Socket Screw:
M3x8
CN9
Duress
5 EVA foam gasket (US/ EU)
Iron bar*2
(Inserted into Product)
Bottom Cover
FCC Statement (part15.21,15.105)
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Installation
Take off two Iron bars from the of bottom body A and and mounting plate B. Pull the
cables from the square holes of the eva foam gasket and mounting plate.
A.
B.
C.
(Excluded)
Use a screwdriver to screw the eva foam gasket C and mounting plate B onto the
wall with Flat Head Cap Philips Tapping Screws (Excluded, the Installer should
prepare before installation. The screws shall not be screwed too tight, or it
could lead to the deformation of the mounting plate.
In-wall
Depth
32mm
Connect the cables to the backside of body A and attach A to B . To fix A on B by inserting
two Iron bars from the bottom of A + B.
Attach the Back Cover D to A. Use the Allen key and screws to assemble the Back
Cover onto the body.
(Excluded)
Hands-off and clear any objects around the 888 (H/K). Turn on the power and
LED will light-up and beep will sound. Wait the Touch IC start for 10 sec. to operate.
D.
Cable selection: Use AWG 22-24 Shielded
Twist Pair to avoid star wiring. Use CAT5 for
TCP/IP connection.
(Excluded)
Indicators:
1*Bi-Color
AR-888
(H/K/U)
3*One Color
LED
AR-PBI-888 1*Bi-Color
Green-Red
Green
(Optional)
White
(Stand-By)
Red
(Optional)
Green-Red
(Exchangeable)
US Mounting Hole: 73x48x40mm(HxWxD)
/ Screw hole pitch : 84mm
Suitable for 70X118 1-module flushmounting box.( Australian, Italy,
USA(501E) Standard)
EU Mounting Hole: 57x53x40mm(HxWxD)
/ Screw hole pitch: 60mm
Suitable for 86X86 flush-mounting box.
(UK, Continental Europe, Germany
Standard)
Steps of Ferrite Core Installation
Power DC Input cable
1. Open up the Ferrite Core box
2. To wind the DC in Cable around the Ferrite Core two times
3. The close up the Ferrite Core
www.soyal.com
Flush-Mounted Series
Basic Commands
Wiring Diagrams
Alarm Output 3-Lift Control Wiring
Enter program mode
123456
AR-401RO16B
Node ID 001
Lift
Controller
Change program code
AR-321L485
Host
BA+
BConverter
A+
RX
Input 6-digit PWD twice
SET
09 654321654321
Add Card User
(Please list down each User Address
and its Card ID)
User Range: 00000~03000
Delete Card User
10 00001 00005
Ex.: 00001 start user address at
00001 and scanned 50 pcs of
card one by one; next time, input
16 15 14 13 12 11 10
24 23 22 21 20 19 18 17
32 31 30 29 28 27 26 25
M6 Mode
Ex.:
00001 start user address at 00001
00005 end user address at 00001
Totally 5 user cards will be
disabled.
PIN=0000 (Disable)
M4/M8 Mode (4/8 beeps
while engtering progrm
mode)
(Delete all cards and parameters)
29 20
Alarm Output 1- Alarm Wiring
UUUUU
FFFFFFFF
064
128
(Enable)
(Disable)
Enable Door Open Too Long Alarm
Enable Arming while exit
program mode
N.C.
N.O.
COM
CTL
12V
External
Relay
Stop Alarm by Push Button
24
24
064
000
(Enable)
(Disable)
Exit Button Wiring
POWER
12VDC
Push Button
AR-PBI888
AR-888 (H)
CN9
Hall-Effect Sensor (Active Low)
CN1
Door Sensor Wiring
N.C.
LA+
LB-
or
Electric Bolt
CN2
GND
DC12V
Alarm
PB
Door SEN.
COM
N.C.
N.O.
Door Lock Wiring
GND
Duress
Arming
Stand-Alone
/Networking
Controller
CN4
Magnetic Lock
WG1
WG0
Buzzer
GLED
RLED
CN5
Electric Strike
M4/M8 Mode
13 00001 4321
WG Reader Wiring
M6 Mode
17 4321
CN1
WG
Open
Open
Short
Short
Short
RST/Bits
Open
Short
Open
Short
Open
Hall-Effect Sensor (Active Low)
GND
DC12V
Card Present
AR-888 (K/U)
13.56MHz WG/ABA Format
(Change by wires connection)
Format SET 1
SET 2
WG 26
Open
Open
WG 34
Open
To GND
ABA-10 To GND
Open
ABA-5-5 To GND To GND
GND
GLED Input (Active High)
RLED Input (Active High)
Note
HEX
HEX
BCD10
BCD
SET1 (Format)
SET2 (Format)
13.56MHz
LA+ (FW Only)
LB- (FW Only)
CN2
WG-Buzzer
WG-GLED
RLED
Reserved
WG0
WG1
CN4 13.56MHz
02 007
Networking Connection Wiring
Set up Node ID
Ex. Node 32 connected to PC
00
032
00
009
032
032
Ex. Node 9 conected to 716E
032=Node ID of Access Controller
032=Virtual 716E Node ID
032=Door number
(All Range:001~254)
009=Node ID of Access Controller
Range: 001~254)
Notice:
Each CH up to
At every 32 units or at every300M
connection to add a RS485 Booster.
Suggest to connect up to 32 units for
each CH of AR-727CM
8 Nodes
BCH2
A+
BCH1
A+
BHost
A+
WG
RST
Format
WG 26
WG 34
RS-232
ABA-8
ABA-10
AR-888 (K/U)
CN9
WG Reader
AR-888 (K/U)
125kHz WG/ABA/RS232 Format
(Change by shorted on PCB)
Exit program mode
21
Alarm
Door Contact
PIN=0000 (Disable)
18 015
FF
S=Set=0~3
FFFFFFFF=0 (Disable) / 1 (Enable)
28
28
Reset to Factory
Default Value
Add Card+PIN User
Set up Door Close Time
UUUUU
GND
GLED Input (Active High)
RLED Input (Active High)
15 1234
TTT: 001~600=1~600 sec.
601~609=0.1~0.9sec.
000=On/ Off (Latch)
(Disable)
Occupied Alarm Output to support
M6 Mode (6 beeps)
Set up Door Relay Time
27
CN1
12 00001 1234
(Enable)
UUUUU=User Address=00000~03000
FF=Floor number=1~32
N.O.
COM
N.C.
GND
DC12V
Delete All User Cards
29 29
Add PIN User
002
000
Assign Users (Single Floor)
N.C.
N.O.
COM
CTL
12V
19*00051*00001#
Attach/Present Card
One by One
24
24
Assign Floor User (Multi-Floor)
Ex. Assign user
address 1 to access
to 1, 3, 5, 7 floor
21*00001*0*01010101#
Lock
M4/M8 Mode
M6 Mode (Must set up 17*0000#)
22 1
External
Relay
10 00001 9 00005
19 00001 00001
Floor/ Stop
Enable Life Control
Alarm Output 2- WG Dual Door
Control Wiring
User Range: 00000~03000
M4/M8 Mode
TTT: 001~600=1~600 sec.
V150708
CN5
125kHz
Multi-Door
Controller
Node ID
001
Converter
AR-321CM
AR-727CM
AR-888(H)
Node ID
254
AR-888(H)
Node ID
032
AR-888(H)
Node ID
002
www.soyal.com
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Instance ID                     : uuid:d123b04d-60de-49d6-9300-b2627c6bf8b4
Original Document ID            : adobe:docid:indd:6bb7d298-5bc0-11e2-9c94-f3300fefe47f
Document ID                     : xmp.id:58624B00DCB9E511B488B39287F2F888
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:08F2A9101CB5E5119A6AE4CF1C176F3A
Derived From Document ID        : xmp.did:9FD8A4EC1BB5E5119A6AE4CF1C176F3A
Derived From Original Document ID: adobe:docid:indd:6bb7d298-5bc0-11e2-9c94-f3300fefe47f
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2016:01:13 17:57:05+08:00
Create Date                     : 2016:01:13 17:57:05+08:00
Modify Date                     : 2016:01:13 17:57:06+08:00
Metadata Date                   : 2016:01:13 17:57:06+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CS6 (Windows)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2ACLEAR-888

Navigation menu