SPAL USA RCU6RX REMOTE CONTOLLER (RX) User Manual RCU6 INSTRUCTIONS
SPAL USA REMOTE CONTOLLER (RX) RCU6 INSTRUCTIONS
SPAL USA >
USERS MANUAL
®
Installation Manual &
Operation Instructions
RCU6
Limited Warranty Statement
SPAL USA WARRANTY STATEMENT
SPAL USA warrants this product to be free from defects in material and workmanship for a
period of one (1) year from the date of sale to the original purchaser, and not more than two (2)
years from the date of manufacture. SPAL USA will repair this product free of charge if, in the
judgment of SPAL USA, it has been proven defective within the warranty period. The product
should be returned, at the customer expense, to the location of original purchase. This warranty
does not cover any expenses incurred in the removal and/or reinstallation of the product.This
warranty does not apply to any product damaged by improper installation, accidental misuse,
abuse, improper line voltage, fire, flood, lightning, or other acts of God, or a product altered or
repaired by anyone other than SPAL USA.This warranty is in lieu of other warranties, expressed
or implied, including any implied warranty of merchantability. No person is authorized to assume
for SPAL USA any other liability concerning the sale of this product.
IMPORTANT-KEEP YOUR INVOICE WITH THIS WARRANTY STATEMENT!
07/04
8
Trouble Shooting Reverse Polarity Wiring Problems
Switch doesn't work properly but the shaved kit transmitters do work
Step 1 Did you purchase a switch kit designed for three switches and only use two switches?
YES - Connect third switch
NO - Check wiring
Switch works properly but shaved kit transmitters do not work
Step 1 Does the LED on the remote light up when you press the transmitter button?
YES - Transmitter works properly continue to step 2
NO - Replace transmitter battery
Step 2 Can you hear the receiver make a clicking sound when you press channel 1 or 2 on
the transmitter?
YES - Receiver and relay work properly. Go to step 4
NO - Go to step 3
Step 3 Does the LED on the receiver light up when the transmitter button is pressed?
YES - Transmitter is properly learned and OK, go to Step 4
NO - Check power and ground to the receiver and then reprogram the transmitters
Step 4 Use a test light to check for voltage at pin 87 of the relay. Did the test show greater
than 10 volts?
YES - The relay checked works properly. The other side of the motor is not properly grounded.
NO - Connect pin 87 to a proper voltage source.
SPAL USA, 512 Tuttle Street, Des Moines, IA 50309-4618
info@spalusa.com, www.spal-usa.com
Main/Sales: 800-345-0327, Sales: 888-SPAL-USA
Tech Support Line: 800-454-7725
V
III
I
VI
IV
II
YELLOW
RED
BLUE / WHITE
GRAY
YELLOW / RED
BLUE
WHITE
WHITE / BLACK
FUSE
(1) Receiver (2) Remotes (2) Wire Harnesses
2
Installation Instructions for
RCU6
This kit is designed to operate six functions via the 6-button remote controls.
These channels can be used to operate power door locks, power door releases, trunk
releases, control linear actuators, or roll up or down power windows.
All channels can be Positive or Negative outputs depending on how the input
wire is connected. Please refer to the diagrams on page __?_ of this instruction
manual for positive, and negative, wiring diagrams and other recommendations, such
as reverse polarity for power windows.
**Proper wiring is critical to the correct operation of this product. Make sure all wires
are properly connected, properly grounded, free of potential damage, and are correctly
fused**
FUSE
Each Kit Contains The Following Components
B
Y
R
TT
AE
Output From Receiver 87A
86 85
30
87
+ 12 VDC
FUSE
30
87A
87
85
86
Output From Receiver
Power Window
Motor
S
W
I
T
C
H
4
Y
T
BATER
85
86
30
87
Output From Receiver 87A
+ 12 VDC Output
+ 12 VDC
FUSE
Optional Wiring Diagrams
Positive Output
Negative Output
Reverse Polarity Output
T
BATY
ER
Output From Receiver
86
Ground Output
30
87A
87
85
GROUND
FUSE
+ 12 VDC
FOR POWER WINDOWS TWO RELAYS MUST BE PLACED BETWEEN THE SWITCH AND THE
WINDOW MOTOR. THE DASHED LINES INDICATE WHERE THE WIRES MUST BE CUT.
5
W
I
R
E
S
W
I
T
C
H
**In a reverse polarity system, a switch that rests at ground must be used.**
Positive Output
To Device
Ground Output
To Device
V
III
I
VI
IV
II
Negative Output From Receiver
Positive Output From Receiver
FCC ID INFORMATION
FCC ID#: KNF6TX
"This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation."
Industry Canada
IC ID#: XXXXXX-6TX (XXXXXX will be replaced with the company number issued by Canada)
“The term “IC:” before the radio certification number only signifies that Industry Canada technical
specifications were met.”
Disclaimer Statement
Caution: changes or modifications not expressly approved by SPAL USA will void the user's
authority to operate the equipment.
V
III
I
VI
IV
II
Reprogramming the Remote Transmitters:
**This RCU6 can accept up to 4 SPAL remote transmitters (Part # RCU6TX)**
The remote transmitters are shipped Pre-Programmed. In the event that a remote
transmitter loses the programmed code, or if you wish to add more remote
transmitters, follow these instructions:
•Make sure ignition is OFF.
•Locate the programming button located on the side of the receiver, next to the LED.
•Press the programming button 3 times (The LED will light).
•Press Button 1 on each remote you wish to program (The LED will turn off for a
moment, then back on with each remote transmitter it recognizes)
•The LED will remain lit for approx. 10 seconds after the last remote transmitter
has been recognized.
•Wait for the LED to go out. Then test each remote transmitter for proper function.
To Operate: Press:
Channel 1 Button I
Channel 2 Button II
Channel 3 Button III
Channel 4 Button IV
Channel 5 Button V
Channel 6 Button VI
Basic Function of the SPAL Shaved Door Kit
The remote control supplied with your kit has four buttons, but is capable of controlling
6 channels.
Channel 1:
Channel 2:
Channel 3:
Channel 4:
Channel 5:
Channel 6:
Operation Section
Programming Section
3
Basic Functions Of The Remote Control
5
Optional Wiring Section
Item to be Description Relay Type # of Relays Diagram
Activated of Function Required
1 Power window motor Move window up & down SPDT 2 Reverse
1 Power window motor Move window one direction SPDT 1 Reverse
Linear actuator Move in & out SPDT 2 Reverse
Solenoid Activate Solenoid SPST 1 Positive or Negative
Trunk Release Open the Trunk SPST 1 Positive or Negative
Door lock actuator Lock & unlock SPDT 2 Reverse
SPST = Single pole single throw relay, 30 or 40 amp
SPDT = Single pole double throw relay 30 or 40 amp
Relays can either be purchased from SPAL USA or from your local auto parts store.
Wiring Options
Positive outputs are +12VDC
Negative outputs are ground
Both outputs are capable of handling 10Amps
V
III
I
VI
IV
II
Receiver Mounting and Wiring:
**The receiver must be mounted inside the vehicle to avoid moisture**
**Do not plug in the receiver module until all the wiring is complete**
**Do Not Ground the Antenna**
ANTENNA
GND
+12V
LED
PROGRAMMING BUTTON
YELLOW
RED
BLUE / WHITE
GRAY
YELLOW / RED
BLUE
WHITE
WHITE / BLACK
+12V
IGN
CH 6 OUTPUT
CH 4 OUTPUT
CH 2 OUTPUT
CH 5 OUTPUT
CH 1 OUTPUT
CH 3 OUTPUT
FUSE
FUSE
Mounting / Wiring Section
Connector 1 Connector 2
Pin # Wire Color Circuit Wire Color Circuit
1Red Input Red Positive 12 VDC
2Yellow Ignition Black Ground
3Blue/White Channel 6
4Gray Channel 4
5Yellow/Red Channel 2
6Blue Channel 5
7White Ignition 1
8White/Black Channel 3
ANTENNA
GND
+12V
PROGRAMMING BUTTON
LED
RED GROUND
IGN
CH 6 OUTPUT
CH 4 OUTPUT
CH 3 OUTPUT
CH 1 OUTPUT
CH 5 OUTPUT
CH 2 OUTPUT
GRAY
BLUE
WHITE / BLACK
WHITE
YELLOW / RED
BLUE / WHITE
YELLOW
FUSE
FUSE
Positive Output
Negative Output