SPAL USA RCU6RX REMOTE CONTOLLER (RX) User Manual RCU6 INSTRUCTIONS

Download:
Mirror Download [FCC.gov]
Document ID	473245
Application ID	ymPVahT0ftPmUAYbVdRcZw==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.75kB (134360 bits)
Date Submitted	2004-09-27 00:00:00
Date Available	2004-09-27 00:00:00
Creation Date	2004-09-10 16:44:08
Producing Software	Acrobat Distiller 5.0.5 for Macintosh
Document Lastmod	2004-09-10 16:44:08
Document Title	RCU6-INSTRUCTIONS
Document Creator	QuarkXPressª: AdobePS 8.7.3 (301)

Trouble Shooting Reverse Polarity Wiring Problems
Switch doesn't work properly but the shaved kit transmitters do work
Step 1
Did you purchase a switch kit designed for three switches and only use two switches?
YES - Connect third switch
NO - Check wiring
®
Switch works properly but shaved kit transmitters do not work
Step 1
Does the LED on the remote light up when you press the transmitter button?
YES - Transmitter works properly continue to step 2
NO - Replace transmitter battery
Step 2
Can you hear the receiver make a clicking sound when you press channel 1 or 2 on
the transmitter?
YES - Receiver and relay work properly. Go to step 4
NO - Go to step 3
Step 3
Does the LED on the receiver light up when the transmitter button is pressed?
YES - Transmitter is properly learned and OK, go to Step 4
NO - Check power and ground to the receiver and then reprogram the transmitters
Step 4
Use a test light to check for voltage at pin 87 of the relay. Did the test show greater
than 10 volts?
YES - The relay checked works properly. The other side of the motor is not properly grounded.
NO - Connect pin 87 to a proper voltage source.
II
III
IV
VI
Limited Warranty Statement
SPAL USA WARRANTY STATEMENT
SPAL USA warrants this product to be free from defects in material and workmanship for a
period of one (1) year from the date of sale to the original purchaser, and not more than two (2)
years from the date of manufacture. SPAL USA will repair this product free of charge if, in the
judgment of SPAL USA, it has been proven defective within the warranty period. The product
should be returned, at the customer expense, to the location of original purchase. This warranty
does not cover any expenses incurred in the removal and/or reinstallation of the product.This
warranty does not apply to any product damaged by improper installation, accidental misuse,
abuse, improper line voltage, fire, flood, lightning, or other acts of God, or a product altered or
repaired by anyone other than SPAL USA.This warranty is in lieu of other warranties, expressed
or implied, including any implied warranty of merchantability. No person is authorized to assume
for SPAL USA any other liability concerning the sale of this product.
IMPORTANT-KEEP YOUR INVOICE WITH THIS WARRANTY STATEMENT!
Installation Manual &
Operation Instructions
SPAL USA, 512 Tuttle Street, Des Moines, IA 50309-4618
info@spalusa.com, www.spal-usa.com
Main/Sales: 800-345-0327, Sales: 888-SPAL-USA
Tech Support Line: 800-454-7725
RCU6
07/04
Each Kit Contains The Following Components
(1) Receiver
(2) Remotes
Positive Output
(2) Wire Harnesses
RED
II
II
III
IV
III
IV
Optional Wiring Diagrams
FUSE
+ 12 VDC
FUSE
YELLOW
BLUE / WHITE
VI
FUSE
VI
87
GRAY
YELLOW / RED
87A
Negative
From Receiver
OutputOutput
From Receiver
86
BLUE
85
WHITE
30
B AT
Positive Output
+ 12ToVDC
Output
Device
WHITE / BLACK
TE R
Negative Output
FCC ID INFORMATION
FCC ID#: KNF6TX
"This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation."
Industry Canada
IC ID#: XXXXXX-6TX (XXXXXX will be replaced with the company number issued by Canada)
“The term “IC:” before the radio certification number only signifies that Industry Canada technical
specifications were met.”
GROUND
87
87A
Positive
From Receiver
OutputOutput
From Receiver
+ 12 VDC
86
FUSE
85
30
B AT
Ground Output
To Device
Ground Output
TE R
Reverse Polarity Output
Disclaimer Statement
Caution: changes or modifications not expressly approved by SPAL USA will void the user's
authority to operate the equipment.
+ 12 VDC
FUSE
87
87A
Output From Receiver
Installation Instructions for
RCU6
This kit is designed to operate six functions via the 6-button remote controls.
These channels can be used to operate power door locks, power door releases, trunk
releases, control linear actuators, or roll up or down power windows.
All channels can be Positive or Negative outputs depending on how the input
wire is connected. Please refer to the diagrams on page __?_ of this instruction
manual for positive, and negative, wiring diagrams and other recommendations, such
as reverse polarity for power windows.
**Proper wiring is critical to the correct operation of this product. Make sure all wires
are properly connected, properly grounded, free of potential damage, and are correctly
fused**
86
5S
WW
I II
R TT
E CCH
85
B AT
30
TE R
30
Output From Receiver
86
85
87A
87
Power Window
Motor
**In a reverse polarity system, a switch that rests at ground must be used.**
FOR POWER WINDOWS TWO RELAYS MUST BE PLACED BETWEEN THE SWITCH AND THE
WINDOW MOTOR. THE DASHED LINES INDICATE WHERE THE WIRES MUST BE CUT.
Operation Section
Mounting / Wiring Section
Receiver Mounting and Wiring:
Basic Function of the SPAL Shaved Door Kit
The remote control supplied with your kit has four buttons, but is capable of controlling
**The receiver must be mounted inside the vehicle to avoid moisture**
**Do not plug in the receiver module until all the wiring is complete**
**Do Not Ground the Antenna**
Positive Output
FUSE
6 channels.
Channel 1:
Channel 2:
Channel 3:
Channel 4:
Channel 5:
Channel 6:
+12V
GND
PROGRAMMING BUTTON
Positive outputs are +12VDC
Negative outputs are ground
Both outputs are capable of handling 10Amps
LED
RED
Basic Functions Of The Remote Control
+12V
To Operate:
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
IGN
III
YELLOW
VI
IV
II
FUSE
BLUE / WHITE
GRAY
CH 4 OUTPUT
YELLOW / RED
CH 2 OUTPUT
BLUE
CH 5 OUTPUT
WHITE
ANTENNA
Connector 1
Wire Color
Red
Yellow
Blue/White
Gray
Yellow/Red
Blue
White
White/Black
CH 3 OUTPUT
Connector 2
Circuit
Input
Ignition
Channel 6
Channel 4
Channel 2
Channel 5
Ignition 1
Channel 3
Wire Color
Red
Black
Programming Section
CH 1 OUTPUT
WHITE / BLACK
Pin #
CH 6 OUTPUT
Circuit
Positive 12 VDC
Ground
Reprogramming the Remote Transmitters:
**This RCU6 can accept up to 4 SPAL remote transmitters (Part # RCU6TX)**
The remote transmitters are shipped Pre-Programmed. In the event that a remote
transmitter loses the programmed code, or if you wish to add more remote
transmitters, follow these instructions:
•Make sure ignition is OFF.
•Locate the programming button located on the side of the receiver, next to the LED.
•Press the programming button 3 times (The LED will light).
•Press Button 1 on each remote you wish to program (The LED will turn off for a
moment, then back on with each remote transmitter it recognizes)
•The LED will remain lit for approx. 10 seconds after the last remote transmitter
has been recognized.
•Wait for the LED to go out. Then test each remote transmitter for proper function.
Negative Output
FUSE
Optional Wiring Section
+12V
GND
Wiring Options
PROGRAMMING BUTTON
LED
RED
FUSE
YELLOW
BLUE / WHITE
GRAY
YELLOW / RED
BLUE
WHITE
ANTENNA
WHITE / BLACK
Press:
Button I
Button II
Button III
Button IV
Button V
Button VI
GROUND
Item to be
Activated
Description
of Function
1 Power window motor
1 Power window motor
Linear actuator
Solenoid
Trunk Release
Door lock actuator
Move window up & down
Move window one direction
Move in & out
Activate Solenoid
Open the Trunk
Lock & unlock
Relay Type
# of Relays Diagram
Required
IGN
CH 6 OUTPUT
CH 4 OUTPUT
CH 2 OUTPUT
CH 5 OUTPUT
CH 1 OUTPUT
CH 3 OUTPUT
SPDT
SPDT
SPDT
SPST
SPST
SPDT
SPST
= Single pole single throw relay, 30 or 40 amp
SPDT
= Single pole double throw relay 30 or 40 amp
Relays can either be purchased from SPAL USA or from your local auto parts store.
Reverse
Reverse
Reverse
Positive or Negative
Positive or Negative
Reverse

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2004:09:10 16:44:08-05:00
Modify Date                     : 2004:09:10 16:44:08-05:00
Page Count                      : 3
Creation Date                   : 2004:09:10 21:44:08Z
Mod Date                        : 2004:09:10 21:44:08Z
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Author                          : 
Metadata Date                   : 2004:09:10 21:44:08Z
Creator                         : ,
Title                           : RCU6-INSTRUCTIONS

EXIF Metadata provided by EXIF.tools