SYMA MODEL AIRCRAFT GC88752-11 WiFi Camera-2 User Manual 3

Download:
Mirror Download [FCC.gov]
Document ID	3328696
Application ID	+Yhv+N7Y0F7clB8EKTfbiQ==
Document Description	User manual 3.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	480.56kB (6007041 bits)
Date Submitted	2017-03-23 00:00:00
Date Available	2017-03-23 00:00:00
Creation Date	2017-01-19 15:23:20
Producing Software	Adobe Acrobat 7.0 Image Conversion Plug-in
Document Lastmod	2017-03-23 14:02:15
Document Title	User manual 3.pdf
Document Creator	Adobe Acrobat 7.0

2. Under the headless mode, the operator
does not need to differentiate the head
position of the drone, and only needs to
control the drone's direction front/back/leftl
right by using the right joystick direction on
the remote control.
8. Photo/Video Instructions
1. After install the camera, turn on the drone, the camera works normally
when the RED indicator changes from flashing to be green and keep
lights on. If the RED indicator only flashing and lights off a few seconds
later, it means the camera was not installed the memory card.
2. How to take photos and videos
Take Photo:
Make sure camera is on, when push the PHOTO
button, a beep from transmitter, camera take a
photo with the GREEN indicator will change to
RED and flash one time.
Take Video:
Make sure camera is on, when push the VIDEO
button, two beeps from transmitter, camera start
to take video after the GREEN indicator change
to RED and keep flashing. To stop and save the
video, press the VIDEO button again ,than
camera indicator stop flashing and keep lights on
as GREEN .
Flight Preparation And Switching
The Drone On And Off
1. Flight Preparation
Step 1: Push the power button of the remote
control.
Step 2: Install the battery pack in drone.
Step 3: Press on the power button on the top
of the drone to make sure the drone is
turned “ON".
Step 4: Push the left joystick (accelerator) up to
the highest point and then push down to
the lowest point. When the led indicator
lights in the drone change from quick
flashing to continuous light, it means
that the drone goes into the flight
standby mode.
drone
Method 1: push the leftjoystick (accelerator)
to the highest point and then back
to the center, the blades of the
drone start rotating slowly.
Move the left and right joysticks
inwards in an internal loop of “8" for1
second, the blades of the drone start
rotating slowly.
Method 3: When the drone is stationary,press
the B button, the drone automatically
takes off and hovers at a certain
3. Turning off the drone
Method 1: Push the leftjoystick (Accelerator)
to the lowest level and hold there for
2 to 3 seconds, the drone can then
be turned off.
Method 2: Move the left and right joysticks
inwards in an internal loop of “8" for 1
second, and the drone can be turned
off.
When the drone is in flight, press the
B button, the drone will descend to
the ground and lands.
When the left joystick (Accelerator) When the right joystick (Direction
is pushed upwards or downwards, Rudder) is pushed upwards or
the drone will ascend or descend downwards, the drone will advance
correspondingly. forward or backward correspondingly.
When the left joystick (Accelerator) When the rightjoystick (Direction
is pushed towards the left or right, Rudder) is pushed towards the left or
the drone will turn left or right right, the drone will fly sideways to the
correspondingly.
Trimming operation
left or right correspondingly.
While the drone is hovering in the air, it
automatically flies forward/backwards, press in on
the left joystick and at the same time push the
right joystick forward/backward slightly to fine tune
the direction. Don‘t release the left joystick until
the drone is flying in a stable state.
While the drone is hovering in the air and
automatically flies left/right, press in on the left
joystick and at the same time push the right
joystick left/right slightly to fine tune the direction.
Don’t release the leftjoystick until the drone is
flying in a stable state.
While the drone is hovering in the air, when the
drone automatically rotates and flies towards the
left/right, press in on the left joystick and at the
same time move joystick to the right or left to
adjust the direction. Don’t release the left
joystick until the drone is flying in a stable state.
Warning: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
oReorient or relocate the receiving antenna.
olncrease the separation between the equipment and receiver.
oConnect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
oConsult the dealer or an experienced radio/TV technician for help.
“This device complies with FCC radiation exposure limits set forth for
general population (uncontrolled exposure).
This device must not be collocated or operating in conjunction with any
other antenna or transmitter."
Decoration of Conformity Inserts:
“Hereby, GuangDong Syma model aircraft Industrial co.,ltd, declares
that this drone is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC
A copy of the full D00 is attached
— RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE).This means that this product must be
handled pursuant to European directive 2012/19/EU in order to be recycled
or dismantled to minimize its impact on the environment.User has the
choice to give his product to a competent recycling organization or to the
retailer when he buys an new electrical or electronic equipment.
Accessories/Parts List
Upper body Lowe body Rotor Blade Foot Stand
suit
Protective Gear Motor Lamp Cover
LED Light Bar
( Red )
LED Light Bar LiF‘o Battery Card Reader Plating Fitting
Blade cover Main stand Blade lockstitch A Blade lockstitch B
a“
0/
Receiver Board Remote Control
Product description
Product Name Produci Name
Top Mam Body cears
aonam Mam Body Mam stand
slauewlockw-se Dnecuom cucun Board
alauqcaumer Clockwwse Dlrefllonp Base oruasn
onleeuve Gear LED nghl aavtgreenl
Battery LED nglll aaqmap
MomrlCIoekwlse mum-om and: \ocksmch A
Mololrcuumu-clockwlse Dwerllon) Blade \ucksmch a
Fool Stand Camera
Lamp Cnver
Blade cover
Main Specifications
Dion's Length:50cm Drone‘s Width:50cm
Drone‘s Heightz19cm Motor’s Model: 132
Battery: 7.4V/2000mAh lithium battery
Rectification procedures
Solution
.The drone has entered into 1. Charge up the drone.
lowvoltage protection. 2. Change the batteries oi
The drone .When the power oi the remote the remote control.
has no control is weak. the power light 3. Adjust the channel oi
response indicator will blink. both the remote control
.The channel selection oithe and drone such that
remote control does not match they are in synchronized
with the drone's coding. mode.
.The power oithe remote
1. change the batteries.
control is weak.
2. change to a place where
there is no interference
with the same trequency.
The ilight
response oi
the drone is
. There is an interierence with
the same irequency as that oi
"°‘ “"5"""3 the remote control.
Problem Solution
. Re-adjust the calibration
until the drone is level
1, The drone is not calibrated to the ground, For further
level to the ground. details, see No.3 on Page
7 tor details (Function 0!
horizontal adjustment).
The drone is
llying towards
its side in one
direction during
novering
. Re-deline tne lront
direction. For runner
details, see on Page a
«or details (Headless
Function).
In the headless
state, it is biased 1, Many collisions may cause
towards the tront head biasness,
direction
Re-adjust the calibration
until the drone is level
to the ground, For further
details, see No.3 on Page
7 tor details (Function 0!
horizontal adjustment).
1. The drone is not calibrated
level to the ground.
Fixed high 2 U ‘ bl . d
instability/ up and ' "5 a e a" Pressure u", ‘6' .Avoid to fly under the
the severe weather condition.
down movement severe weather condition,
3. Violent collision resulting in
data disorder or gyroscope. ' ”'ak“ h°”‘°"“'
adjustment again, see
No.3 on Page 7 lor details
(Function oi horizontal
adjustment).
.18.
Manufacturer
Guangdong Syma Model drone Industrial Co., Ltd.
The Crossing of No.2 West Xingye Road and North Xingye Road,Laimei.
Industrial Park Chenghai District Shantou City Guangdong China.
The company has the right of final interpretation
of this instruction manual statement.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2017:01:19 15:23:20+08:00
Creator                         : Adobe Acrobat 7.0
Modify Date                     : 2017:03:23 14:02:15+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2017:03:23 14:02:15+08:00
Creator Tool                    : Adobe Acrobat 7.0
Format                          : application/pdf
Document ID                     : uuid:39f3aa82-1b6d-4b80-ac24-565fde2bfdbf
Instance ID                     : uuid:4d2a682d-eb12-4b48-907d-8ac5a3dd8543
Producer                        : Adobe Acrobat 7.0 Image Conversion Plug-in
Page Count                      : 10

EXIF Metadata provided by EXIF.tools