SZ DJI TECHNOLOGY 800RX1504 RONIN RX User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	2605909
Application ID	iXTv1AdxCUj0JgwNUxGVtA==
Document Description	User Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	490.12kB (6126504 bits)
Date Submitted	2015-05-06 00:00:00
Date Available	2015-05-06 00:00:00
Creation Date	2015-05-06 13:51:38
Producing Software	Adobe Acrobat Pro 9.3.2
Document Lastmod	2015-05-06 13:51:57
Document Title	User Manual 1
Document Creator	Adobe Acrobat Pro 9.3.2

Thumb Controller
User Manual
V1.0 2015.4
Disclaimers and Warnings
Congratulations on purchasing your new DJI product. Carefully read
the manual and all disclaimers before using this product. By using
this product, you hereby agree to this disclaimer and signify that you
have read it in its entirety. You agree that you are responsible for your
own conduct, for all content that is created using this product, and for
any consequences that may arise from either. You agree to use this
product only for purposes that are proper and in accordance with local
regulations, stated terms, and all applicable polices and guidelines.
By reading this disclaimer, you also agree that:
1. Any part of this disclaimer is subject to change without prior
notice. Refer to www.dij.com for the latest version.
2. DJI reserves the right of final interpretation of this disclaimer.
As DJI has no control over use, setup, final assembly, modification,
or misuse of its products, no liability shall be assumed or accepted
for any resulting damage or injury. By using, setting up, or
assembling the product, the user accepts all resulting liability. DJI
assumes no liability for damages or injuries incurred directly or
indirectly from the use of this product.
DJI is a registered trademark. All names of products, brands, etc.
appearing in this manual are trademarks or registered trademarks
of their respective owner companies. This product and manual are
copyrighted by DJI, with all rights reserved. No part of this product
or manual shall be reproduced in any form without the prior written
consent or authorization of DJI. No patent liability is assumed with
respect to the use of the product or information contained herein.
© 2015 DJI. All Rights Reserved.
Content
Disclaimers and Warnings
In the Box
Introduction
Thumb Controller
External Receiver (For Ronin Only)
Installation
Installing the Thumb Controller
Installing the External Receiver (For Ronin Only)
Connecting the Thumb Controller to the Gimbal
Connecting the Thumb Controller to the Ronin-M
Connecting the Thumb Controller to the Ronin
Indicator Status
Using the Thumb Controller
Mode
Function
Gimbal Settings
Device Settings
DJI Assistant App Tuning
DJI PC/MAC Assistant Tuning
Settings
Updating the Thumb Controller and the Receiver
Specifications
11
12
12
13
13
14
16
17
17
18
20
© 2015 DJI. All Rights Reserved.
In the Box
Check to ensure that all of the following items are included in the
package. If any items are missing, contact DJI or your local dealer.
The following items are included with the Thumb Controller for the
Ronin-M:
Thumb Controller×1
Quick Release Accessory
Mount×1
USB Cable×1
Rubber
Ring×1
The following items are included with the Thumb Controller for the Ronin:
Thumb Controller×1
Receiver×1
Quick Release Accessory
Mount ×1
4-Pin Cable×1
© 2015 DJI. All Rights Reserved.
USB Cable×1
Adhesive Tape×1
Introduction
The Thumb Controller is designed specifically for DJI Ronin series
handheld gimbals. It provides a simple, intuitive interface for
controlling the gimbal’s pan, tilt, and roll motion. The pressuresensitive stick and the easy-to-read OLED display give Ronin users
more control than ever before.
The Thumb Controller communicates with the Ronin-M via a
preinstalled internal receiver. An external receiver is needed when
the Thumb Controller is used with the Ronin.
Thumb Controller
[1]
[3]
[4]
[2]
[1] Power Button
Press and hold the power
button to turn on/off the Thumb
Controller
[2] Status Indicator
Indicates the status of the
Thumb Controller
[3] OLED Display
Displays the menu of the
Thumb Controller
[4] Pressure-Sensitive Stick
Transmits the user’s input to
the force sensor
© 2015 DJI. All Rights Reserved.
[5] Micro-USB Port
For charging the Thumb
Controller and upgrading its
firmware
[5]
[6] Override Button
Allow the Thumb Controller
to reactivated and updated
following a failure update
process
[6]
External Receiver (For Ronin Only)
[1]
[3]
[2]
[1] CAN Port
Connects the receiver to the
Ronin
[2] Bind Button
Connects the Thumb
Controller to the Ronin
[3] LED Indicator
Indicates the status of the
receiver
[4]
© 2015 DJI. All Rights Reserved.
[4] Micro-USB Port
For upgrading the firmware
Installation
Installing the Thumb Controller
1. Install the quick-release accessory mount by clamping it around
the handlebar of the Ronin and tightening the screw. Remember
to place the rubber ring on the on the handlebar and clamp the
accessory mount around it when installing the unit on the Ronin-M.
2. Insert the Thumb Controller into the quick-release accessory
mount and ensure that it is secure.
© 2015 DJI. All Rights Reserved.
Installing the External Receiver (For Ronin Only)
1. Use the 4-pin cable to connect the CAN port on the Ronin to the
CAN 1 or Can 2 port on the receiver.
2. Use the adhesive tape to secure the receiver on the Ronin.
© 2015 DJI. All Rights Reserved.
Connecting the Thumb Controller to the Gimbal
Connecting the Thumb Controller to the Ronin-M
1. Turn on the Ronin-M.
2. Press the Ronin-M’s Bind Button (shown below) one time. The
LED indicator on the Ronin-M will rapidly blink green.
3. Turn on the Thumb Controller. If the LED indicator on the Ronin-M
and the LED indicator on the Thumb Controller both glow solid
green, they have been successfully connected.
Bind Button
Connecting the Thumb Controller to the Ronin
1. Turn on the Ronin.
2. Press the Bind Button on the receiver one time. The LED indicator
on the receiver will rapidly blink green.
3. Turn on the Thumb Controller. If the LED indicator on the receiver
and the LED indicator on the Thumb Controller both glow solid
green, they have been successfully connected.
© 2015 DJI. All Rights Reserved.
Bind Button
The binding process only needs to be completed one time,
unless the bind button is pressed or the Ronin/Ronin-M
needs to be connected to another Thumb Controller.
10
© 2015 DJI. All Rights Reserved.
Indicator Status
Thumb Controller
LED Indicator Status
— Solid Red
Blinking Red
— Solid Green
Description
The Thumb Controller is being
updated
The Thumb Controller is not connected
to the receiver
The Thumb Controller is connected to
the receiver
Blinking Green The update process is complete
— Solid Yellow
External Receiver LED
Indicator Status
— Solid Red
Blinking Red
— Solid Green
Blinking Green
The Thumb Controller is fully charged
Description
The receiver is being updated
The Thumb Controller is not
connected to the receiver
The Thumb Controller is
connected to the receiver
The update process is complete
Blinking Green Quickly Binding
© 2015 DJI. All Rights Reserved.
11
Using the Thumb Controller
To enter the Main Menu, press and hold the center of the pressuresensitive stick.
Mode
Function
ST Off
ST On
Auto Center
Fast
Normal
Slow
Up/Down
Channel
Left/Right
Gimbal Setting
Direction
Menu
Calibration
Sensitivity
Device Setting
Sleep
Power off
12
Default Setting
Restore
About
Version **
© 2015 DJI. All Rights Reserved.
Up/Down
Left/Right
Cali System
Auto Tune
Soft
Hard
1min
5min
10min
Never
10min
30min
60min
Never
Pan
Roll
Tilt
None
Pan
Roll
Tilt
None
Normal
Reverse
Normal
Reverse

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2015:05:06 13:51:38-04:00
Creator                         : Adobe Acrobat Pro 9.3.2
Modify Date                     : 2015:05:06 13:51:57-04:00
Has XFA                         : No
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2015:05:06 13:51:57-04:00
Creator Tool                    : Adobe Acrobat Pro 9.3.2
Format                          : application/pdf
Document ID                     : uuid:6a57e35d-35fc-4b31-9542-8cb27aef7958
Instance ID                     : uuid:86403e89-b8d6-443a-9426-b67baa3a17c7
Producer                        : Adobe Acrobat Pro 9.3.2
Page Count                      : 12

EXIF Metadata provided by EXIF.tools