SZ DJI TECHNOLOGY NB06251803 Multilink User Manual x

SZ DJI TECHNOLOGY CO., LTD Multilink x

User Manual

MultilinkUserGuide V1.0 2018.04
Product Profile Introduction Multilink is specially designed to use with Inspire 2 standard remote controller controllercontrollers. Multiple slave remote controllers network is a star network type, with a master remote controller working as the transmission hub to send the command from slave remote controllers to the aircraft. Features 1.Supported one master remote controller and three slave remote controllers.Master remote controller-pilot, slave remote controller 1-gimbal, slave remote controller 2-focus, slave remote controller 3-view control. 2.Gimbal control:Master remote controller and slave remote controller 1 shares gimbal control by snatching, slave remote controller2 and slave remote controller3 cannot control the gimbal. 3.Camera control: all remote controller share camera control. 4.Supported both standard and Cendence remote controllers, any of which can be set as master or slave remote controller. In the Box Multilink Module×1 Overview Usage Installation and Connection Multilink can be installed onto both Standard Remote Controller andCendence Remote Controller via To Standard Remote Controller To Cendence Remo te Controller Antenna Tightening Knob CAN Cable Status Indicator different tightening holes. (FCC ID:SS3-GL800A1703).(FCC ID:SS3-GL6D10A1609)and Cendence remote controllers network with up to three slave remote which can form multiple slave remote
Follow below steps for installation. 1. Mount the Multilink module onto the remote controller and tighten the knob. 2. Connect the CAN cable to the remote controller’s CAN port. 3. The indicator turns green after successful connection. And turn red if failed. Tip: CAN cable can be connected to the Patch Antenna module if Patch Antenna used. And make sure the Patch Antenna is connected correctly and firmly. Settings Follow below steps to set the Multilink as master or slave remote controller. Master remote controller 1. Set the Multilink as master remote controller in app. 2. Set an access password. Slave remote controller 1. Check the three remote controllers setting status and then select the required position in the app. 3. Enter the access password. 2. Waiting. The indicator turns green after successfully matched. Usage Details 1. Master remote controller can control the aircraft, gimbal, camera and vision systems. 2. Slave remote controller 1 can control the gimbal and camera. 3. Slave remote controller2 and 3 can only control the camera. Tips: 1. Firmware upgrade can be done in the app by connecting the Multilink to the remote controller. 2. The CAN port on the Multilink can be connected to other DJI CAN devices. 3. Maximum work efficiency is available when used with a Patch Antenna.
FCCComplianceNoticeThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)Thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.Anychangesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperatetheequipment.ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:—Reorientorrelocatethereceivingantenna.—Increasetheseparationbetweentheequipmentandreceiver.—Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.—Consultthedealeroranexperiencedradio/TVtechnicianforhelp.. Forbodywornoperation,this  hasbeentestedandmeetstheFCCRFexposureguidelineswhenusedwithanaccessorydesignatedforthisproductorwhenusedwithanaccessorythatcontainsnometalandthatpositionsthe aminimumof mm from thebody.RF Exposure Information            10devicedeviceSAR tests are conducted using standard operating positions accepted by the FCC with thedevice transmitting at its highest certified power level in all tested frequency bands, althoughthe SAR is determined at the highest certified power level, the actual SAR level of the devicewhile operating can be well below the maximum value .the FCC that it does not exceed the exposure limit established by the FCC, Tests for each device are performed in positions and locations as required by the FCC.Before a new device is a available for sale to the public, it must be tested and certified to

Navigation menu