SZ DJI TECHNOLOGY NB06251803 Multilink User Manual x

Download:
Mirror Download [FCC.gov]
Document ID	3892310
Application ID	kzrgPOHYaVPuPq9QuqylJA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	50.21kB (627590 bits)
Date Submitted	2018-06-18 00:00:00
Date Available	2018-08-02 00:00:00
Creation Date	2018-05-08 09:33:05
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2018-06-18 14:53:54
Document Title	Microsoft Word - User Manual.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	DG06118

MultilinkUserGuide
V1.0
2018.04
Product Profile
Introduction
Multilink is specially designed to use with Inspire 2 standard remote controller(FCC ID:SS3-GL6D10A1609)
and Cendence remote controller (FCC ID:SS3-GL800A1703). which can form multiple slave remote
controllers network with up to three slave remote controllers. Multiple slave remote controllers
network is a star network type, with a master remote controller working as the transmission hub to
send the command from slave remote controllers to the aircraft.
Features
1.Supported one master remote controller and three slave remote controllers.Master remote
controller-pilot, slave remote controller 1-gimbal, slave remote controller 2-focus, slave remote controller
3-view control.
2.Gimbal control:Master remote controller and slave remote controller 1 shares gimbal control by
snatching, slave remote controller2 and slave remote controller3 cannot control the gimbal.
3.Camera control: all remote controller share camera control.
4.Supported both standard and Cendence remote controllers, any of which can be set as master or slave
remote controller.
In the Box
Multilink Module×1
Overview
CAN Cable
Antenna
To
Standard
Controller
To
Remote
Tightening Knob
Cendence
Remote
Controller
Status Indicator
Usage
Installation and Connection
Multilink can be installed onto both Standard Remote Controller andCendence Remote Controller via
different tightening holes.
Follow below steps for installation.
1.
Mount the Multilink module onto the remote controller and tighten the knob.
2.
Connect the CAN cable to the remote controller’s CAN port.
3.
The indicator turns green after successful connection. And turn red if failed.
Tip:
CAN cable can be connected to the Patch Antenna module if Patch Antenna used. And make sure the
Patch Antenna is connected correctly and firmly.
Settings
Follow below steps to set the Multilink as master or slave remote controller.
Master remote controller
1.
Set the Multilink as master remote controller in app.
2.
Set an access password.
Slave remote controller
1.
Check the three remote controllers setting status and then select the required position in the app.
3.
Enter the access password.
2.
Waiting. The indicator turns green after successfully matched.
Usage Details
1.
Master remote controller can control the aircraft, gimbal, camera and vision systems.
2.
Slave remote controller 1 can control the gimbal and camera.
3.
Slave remote controller2 and 3 can only control the camera.
Tips:
1.
Firmware upgrade can be done in the app by connecting the Multilink to the remote controller.
2.
The CAN port on the Multilink can be connected to other DJI CAN devices.
3.
Maximum work efficiency is available when used with a Patch Antenna.
FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
SAR tests are conducted using standard operating positions accepted by the FCC with the
device transmitting at its highest certified power level in all tested frequency bands, although
the SAR is determined at the highest certified power level, the actual SAR level of the device
while operating can be well below the maximum value .
Before a new device is a available for sale to the public, it must be tested and certified to
the FCC that it does not exceed the exposure limit established by the FCC, Tests for each
device are performed in positions and locations as required by the FCC.
For body worn operation, this device has been tested and meets the FCC RF. exposure
guidelines when used with an accessory designated for this product or when used with an
accessory that contains no metal and that positions the device a minimum of 10 mm from
the body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : DG06118
Create Date                     : 2018:05:08 09:33:05+08:00
Modify Date                     : 2018:06:18 14:53:54-07:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Title                           : Microsoft Word - User Manual.docx
Creator                         : DG06118
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2018:06:18 14:53:54-07:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:2a6f36d0-1c9e-4a8c-b8e6-3c2e7e2d2a85
Instance ID                     : uuid:13656279-9f2d-4683-9b0c-b4f09bb370ed
Page Count                      : 4

EXIF Metadata provided by EXIF.tools