SZ DJI TECHNOLOGY WM331A1609 Phantom 4 Pro User Manual 3
SZ DJI TECHNOLOGY CO., LTD Phantom 4 Pro 3
Contents
- 1. User Manual Part 1
- 2. User Manual Part 2
- 3. User Manual Part 3
- 4. Users Manual Part 1
- 5. Users Manual Part 2
Users Manual Part 2
Phantom 4 Pro/Pro+ User Manual "GUFSDPOmSNFEXJUIUIF5BQ'MZTFMFDUJPO UIFBJSDSBGUXJMMnZBVUPNBUJDBMMZUPXBSETUIFBSFBNBSLFECZ JDPO/PUFUIBUZPVDBOTUJMMVTFUIFDPOUSPMTUJDLUPDPOUSPMUIFNPWFNFOUPGUIFBJSDSBGUEVSJOHUIFnJHIU OPTI Safe to fly (GPS) ISO 100 1/320 EV 0 4821 JPEG MENU STOP Aircraft H: 39M V.S 2.3 M/S D: 210M H.S 4.2 M/S 232M Note that the aircraft will also automatically adjust its speed when it senses there is obstacle at the front PGUIFBJSDSBGUPSJUJTnZJOHUPPDMPTFUPUIFHSPVOE)PXFWFS UIFVTFSTIPVMEOPUSFMZPOUIJTGFBUVSFUP navigate the aircraft between the obstacles. Meanwhile the FailSafe procedure will override the TapFly PQFSBUJPO HJWFOUIBUJGUIF(14TJHOBMJTXFBLUIFBJSDSBGUXJMMFYJUUIFBVUPOPNPVTnJHIUGSPN5BQ'MZBOE nZCBDLUPUIF)PNF1PJOUBVUPNBUJDBMMZ Exit TapFly Use the following methods to exit TapFly: 1. Press once on the Intelligent Flight Pause button on the remote controller or pull back the pitch stick on the remote controller. 2. Tap âSTOPâ button on the screen. STOP OR OR Intelligent Flight Pause button Aircraft will stop and hover after exit from TapFly. You may either tap a new target direction to proceed to UIFOFYUnJHIUPSCSJOHCBDLUIFBJSDSBGUUPUIF)PNF1PJOUNBOVBMMZ ActiveTrack ActiveTrack allows you to mark and track a moving object on your mobile device screen. The aircraft will BVUPNBUJDBMMZBWPJEPCTUBDMFTJOJUTnJHIUQBUI Using ActiveTrack Ensure the Intelligent Flight Battery has more than 50% power and the aircraft is in either P-mode. Then follow the steps below to use ActiveTrack: 1. Take off and hover at least 9 feet (3 meters) above the ground. 20 Š 2016 DJI. All Rights Reserved. Phantom 4 Pro/Pro+ User Manual above 3m ON OFF Auto Hold 2. In the DJI GO app, tap OPTI Safe to fly (GPS) Aircraft OPTI UPCSJOHVQUIFnJHIUNPEFTBOEUIFOTFMFDU Safe to fly (GPS) MENU Click on flight with finger ACTMETRACK Smart to follow Normal mode SMARTmode Advanced %SBHBCPYBSPVOEUIFPCKFDUZPVXBOUUPUSBDLBOEUBQJUUPDPOmSNUIFTFMFDUJPO5IFCPY XJMMUVSOHSFFOXIFOUSBDLJOHJTJOQSPHSFTT*GUIFCPYUVSOTSFE UIFPCKFDUXBTOPUJEFOUJmFEBOEZPV should try again. Safe to fly (GPS) OPTI ISO 100 1/320 EV 0 4821 JPEG MENU Smart to follow H: 39M V.S 2.3 M/S D: 210M H.S 4.2 M/S 232M %0/05TFMFDUBOBSFBDPOUBJOJOHQFPQMF BOJNBMT TNBMM mOFPCKFDUT FHUSFFCSBODIFT and power lines) or transparent objects (e.g. glass or water surface). 4UBZDMFBSPGPCTUBDMFTOFBSUIFnJHIUQBUI QBSUJDVMBSMZXIFOUIFBJSDSBGUJTnZJOHCBDLXBSE Be extra vigilant when using ActiveTrack in any of the following situations: a) The tracked subject is not moving on a level plane. b) The tracked subject changes shape drastically while moving. c) The tracked subject could be blocked or out of sight for a long time. Š 2016 DJI. All Rights Reserved. 21 Phantom 4 Pro/Pro+ User Manual d) The tracked subject is moving on a snowy surface. e) The lighting is extremely low (< 300 lux) or high (> 10,000 lux). f) The tracked subject has a similar color or pattern as its surrounding environment. You must follow local privacy laws and regulations when using ActiveTrack. 5IFBJSDSBGUXJMMTFOTFBOEBWPJEPCTUBDMFTPOJUTnJHIUQBUI If the aircraft loses track of the subject, because it is moving too fast or obscured, re-select the subject to resume tracking. Aircraft Exiting ActiveTrack There are two ways to exit ActiveTrack: 1. Press the Intelligent Flight Pause button on the remote controller. 2. Pull the pitch stick backward. STOP OR After exiting ActiveTrack, the aircraft will stop and hover in place, at which point you may choose to start a new mission or bring the aircraft back to the Home Point. Vision Positioning and Obstacle Sensing System The DJI Vision Positioning System uses ultrasound and image data to help the aircraft maintain its current position. With the help of Vision Positioning, your Phantom 4 Pro/Pro+ can hover in place more precisely BOEnZJOEPPSTPSJOPUIFSFOWJSPONFOUTXIFSFB(14TJHOBMJTOPUBWBJMBCMF5IFNBJODPNQPOFOUTPG the Vision Positioning System are located on the bottom of your Phantom 4 Pro/Pro+, including [1] [2] [3] three binocular sensors and [4] two ultrasonic sensors. The Obstacle Sensing System is consist of [1] [2] two binocular sensors and [5] infrared module on both sides, which constantly scans for obstacles around, allowing it to avoid collisions by going around, over or hovering. [1] [5] [2] [3] [4] 22 Š 2016 DJI. All Rights Reserved. Phantom 4 Pro/Pro+ User Manual Detection Range The detection range of the Vision Positioning and Obstacle Sensing System is depicted as follow. Note that the aircraft cannot sense and avoid the obstacles that are not within the detection range. Aircraft *O5BQnZBOE"DUJWF5SBDLNPEF CPUIUIF7JTJPO1PTJUJPOJOHBOE0CTUBDMF4FOTJOH4ZTUFNXPSLTJG UIFTQFFEJTXJUIJONT0UIFSXJTFUIFCJOPDVMBSTFOTPSDPOUSBSZUPUIFnJHIUEJSFDUJPOJTEJTBCMFE Calibrating Sensors Vision Positioning and Obstacles Sensing sensors that are calibrated on delivery. However these sensors are vulnerable to excessive impact, hence it will require calibration via DJI Assistant 2 from time to time. Follow the steps below to calibrate the camera when the DJI GO app prompt you to do so. 01 02 03 6UOTZZNKGOXIXGLZZU]GXJZNKYIXKKT 'ROMTZNKHU^KY 6GTGTJZORZZNKGOXIXGLZ Using Vision Positioning Vision Positioning is activated automatically when the aircraft is turned on. No further action is required. Vision Positioning is typically used in indoor environments, where GPS is unavailable. Using the sensors that are built into the Vision Positioning system, the aircraft can hover precisely even without GPS. Š 2016 DJI. All Rights Reserved. 23 Phantom 4 Pro/Pro+ User Manual Follow the steps below to use Vision Positioning: Aircraft 5PHHMFUIFnJHIUNPEFTXJUDIUP1NPEF 1MBDFUIFBJSDSBGUPOBnBUTVSGBDF/PUFUIBUUIF7JTJPO1PTJUJPOJOHTZTUFNDBOOPUXPSL properly on surfaces without clear pattern variations. 5VSOPOUIFBJSDSBGU5IFBJSDSBGUTUBUVTJOEJDBUPSXJMMnBTIHSFFOUXPUJNFT XIJDIJOEJcates the Vision Positioning system is ready. Gently push the left stick up to lift off and the aircraft will hover in place. ON OFF Auto Hold Assisted Braking from Obstacle Sensing System Powered by the Obstacle Sensing System, the aircraft will now be able to actively initiate breaks when obstacles are detected direct ahead of the aircraft. Note that Obstacle System works best when light condition is ideal and the obstacle does not have feature-less pattern. In addition, the aircraft speed cannot exceed over 14 meter/second so that the aircraft can break and stop at the safe distance. 7KH7R)GLVWDQFHPHDVXUHPRGXOHRQO\ZRUNVLQ7DSĂ\DQG$FWLYH7UDFNPRGHĂ\ZLWKFDXWLRQ The performance of your Vision Positioning System is affected by the surface over which it is nZJOH5IFVMUSBTPOJDTFOTPSTNBZOPUCFBCMFUPBDDVSBUFMZNFBTVSFEJTUBODFTXIFOPQFSBUJOH above sound-absorbing materials. In addition, the camera may not function correctly in suboptimal environments. The aircraft will switch from P-mode to A-mode automatically if neither GPS nor Vision Positioning System are available. Operate the aircraft with great caution in the following situations: Flying over monochrome surfaces (e.g. pure black, pure white, pure red, pure green). 'MZJOHPWFSBIJHIMZSFnFDUJWFTVSGBDFT Flying at high speeds(over 10 m/s at 2 meters or over 5 m/s at 1 meter). Flying over water or transparent surfaces. Flying over moving surfaces or objects. Flying in an area where the lighting changes frequently or drastically. Flying over extremely dark (lux < 10) or bright (lux > 100,000) surfaces. Flying over surfaces that can absorb sound waves (e.g. thick carpet). Flying over surfaces without clear patterns or texture. Flying over surfaces with identical repeating patterns or textures (e.g. tiles with the same design). 'MZJOHPWFSJODMJOFETVSGBDFTUIBUXJMMEFnFDUTPVOEXBWFTBXBZGSPNUIFBJSDSBGU 24 Š 2016 DJI. All Rights Reserved. Phantom 4 Pro/Pro+ User Manual Keep the sensors clean at all times. Dirt or other debris may adversely affect the effectiveness of the sensors. Vision Positioning is only effective when the aircraft is at altitudes of 0.3 to 10 meters. 5IF7JTJPO1PTJUJPOJOH4ZTUFNNBZOPUGVODUJPOQSPQFSMZXIFOUIFBJSDSBGUJTnZJOHPWFSXBUFS The Vision Positioning System may not be able to recognize pattern on the ground in low light conditions (less than 100 lux). Do not use other ultrasonic devices with frequency of 40 KHz when Vision Positioning system is in operation. Flight Recorder Flight data is automatically recorded to the internal storage of the aircraft. This includes flight telemetry, aircraft status information, and other parameters. To access these data, connect the aircraft to the PC through the Micro USB port and launch the DJI GO app. Attaching and Detaching the Propellers Use only DJI approved propellers with your Phantom 4 Pro / Pro+. The grey and black ring on the propeller indicate where they should be attached and in which direction whey should spin. Propellers Silver Ring Black Ring Figure Attach On Legends Motors without three dots Motors with three dots Lock : Turn the propellers in the indicated direction to mount and tighten. Unlock : Turn the propellers in the indicated direction to loosen and remove. Attaching the Propellers 1. Be sure to remove the warning stickers from the motors before attaching the propellers. 2. Mount the propellers with black propeller rings to the motors with black dots. Mount the propellers with sliver propeller rings to the motors without black dots. Press t he propeller down onto the mounting plate and rotate in the lock direction until it is secured in its position. Š 2016 DJI. All Rights Reserved. 25 Aircraft Keep the animals away from the aircraft when Vision Positioning system is activated. The sonar sensor emits high frequency sounds that are only audible to some animals. Phantom 4 Pro/Pro+ User Manual Be aware of the sharp edges of the propellers. Handle with care. Use only the DJI approved propellers. Do not intermix the propellers types. Stand clear of the motors and DO NOT touch the propellers when they are spinning. Detaching the Propellers Press down the propellers onto the motor mount, rotate the propeller according to the marked direction to unlock the propeller. Aircraft $IFDLUIBUUIFQSPQFMMFSTBOENPUPSTBSFJOTUBMMFEDPSSFDUMZBOEmSNMZCFGPSFFWFSZnJHIU &OTVSFUIBUBMMQSPQFMMFSTBSFJOHPPEDPOEJUJPOCFGPSFFBDInJHIU%0/05VTFBHFE DIJQQFE or broken propellers. To avoid injury, STAND CLEAR of and DO NOT touch propellers or motors when they are spinning. 0/-:VTFPSJHJOBM%+*QSPQFMMFSTGPSBCFUUFSBOETBGFSnJHIUFYQFSJFODF DJI Intelligent Flight Battery The DJI Intelligent Flight Battery has a capacity of 5870 mAh, a voltage of 15.2 V, and a smart charge/ discharge functionality. It should only be charged using an appropriate charger that has been approved by DJI. Intelligent Flight Battery Charger The Intelligent Flight Battery must be fully charged before using it for the first time. Refer to âCharging the Intelligent Flight Batteryâ for more information. Be aware that the output power of the supplied Phantom 4 Pro / Pro+ charger is 100W. DJI Intelligent Flight Battery Functions 1. Battery Level Display: The LED indicators display the current battery level. 2. Battery Life Display: The LEDs display the current battery power cycle. 3. Auto-Discharging Function: To prevent swelling, the battery automatically discharges to below 65% of total power when it is idle for more than ten days. It takes around two days to discharge the battery to 65%. It is normal to feel moderate heat being emitted from the battery during the discharge process. Discharge thresholds can be set in the DJI GO app. 4. Balanced Charging: Automatically balances the voltage of each battery cell when charging. 5. Overcharge Protection: Charging automatically stops when the battery is fully charged. 6. Temperature Detection: The battery will only charge when the temperature is between 5°C (41°F) and 40°C (104°F). 26 Š 2016 DJI. All Rights Reserved. Phantom 4 Pro/Pro+ User Manual 7. Over Current Protection: The battery stops charging when high amperage (more than 8 A) is detected. 8. Over Discharge Protection: To prevent over-discharge damage, discharging automatically stops when the battery voltage reaches 12 V. 9. Short Circuit Protection: Automatically cuts the power supply when a short circuit is detected. 10. Battery Cell Damage Protection: The DJI GO app displays a warning message when a damaged battery cell is detected. 11. Battery Error History: Browse the battery error history in the DJI GO app. 12. Sleep Mode: To save power, the battery enters sleep mode after 20 minutes of inactivity. 13. Communication: Information pertaining to the batteryâs voltage, capacity, current, etc. is transmitted to the aircraftâs main controller. Using the Battery LED1 LED2 LED3 LED4 Power Button (Built-in LED) Battery Level Indicators Turning ON/OFF Turning On: Press the Power Button once, then press again and hold for 2 seconds to turn on. The Power LED will turn red and the Battery Level Indicators will display the current battery level. Turning Off: Press the Power Button once, then press again and hold for 2 seconds to turn off. The CBUUFSZQPXFS-&%XJMMnBTIXIFOQPXFSJOHPGGUIF1IBOUPNUPBMMPXBVUPNBUJDBMMZTUPQQJOH of a recording during the event recording wasnât stopped. The Battery Level Indicators will also show the current battery level during charging and EJTDIBSHJOH5IFJOEJDBUPSTBSFEFmOFECFMPX : LED is on. : LED is off. -&%JTnBTIJOH Š 2016 DJI. All Rights Reserved. 27 Aircraft Refer to Phantom 4 Pro / Pro+ Intelligent Flight Battery Safety Guidelines before use. Users take full responsibility for all operations and usage. Phantom 4 Pro/Pro+ User Manual Battery Level LED1 LED2 LED3 LED4 Battery Level 87.5%~100% 75%~87.5% 62.5%~75% 50%~62.5% 37.5%~50% 25%~37.5% Aircraft 12.5%~25% 0%~12.5% =0% Low Temperature Notice: #BUUFSZDBQBDJUZJTTJHOJmDBOUMZSFEVDFEXIFOnZJOHJOMPXUFNQFSBUVSF ÂĄ$ FOWJSPONFOUT 2. It is not recommended that the battery be used in extremely low temperature (< -10°C) environments. Battery voltage should reach the appropriate level when operating environment with temperatures between -10°C and 5°C. &OEUIFnJHIUBTTPPOBTUIF%+*(0BQQEJTQMBZTUIFi-PX#BUUFSZ-FWFM8BSOJOHwJOMPXUFNQFSBUVSF environments. ,FFQUIFCBUUFSZJOEPPSTUPXBSNJUCFGPSFnZJOHJOMPXUFNQFSBUVSFFOWJSPONFOUT 5. To ensure optimal performance of the battery, keep the battery temperature above 20°C. 6. The charger will stop charging the battery if the battery cellâs temperature is not within the operating range (0°C ~ 40°C ). In cold environments, insert the battery into the battery compartment and allow the aircraft for approximately 1-2 minutes to warm up before taking off. Checking the Battery Level The Battery Level Indicators display how much power remains. When the battery is turned off, press the Power Button once. The Battery Level Indicators will light up to display the current battery level. See below for details. Battery life Battery life refers to how many more times the battery can be discharged and recharged before it must be replaced. When the battery is turned off, press and hold the Power Button for 5 seconds to check the battery life. The Battery Level Indicators will light up and/or blink for two seconds, as shown below: 28 Š 2016 DJI. All Rights Reserved. Phantom 4 Pro/Pro+ User Manual Battery Life LED1 LED2 LED3 LED4 Battery Life 90%~100% 80%~90% 70%~80% 60%~70% 50%~60% 40%~50% Aircraft 30%~40% 20%~30% below 20% When battery life reaches 0%, it can no longer be used. For more information about the battery, launch the DJI GO app and check the information that is listed under the battery tab. Charging the Intelligent Flight Battery 1. Connect the Battery Charger to a power source (100-240 V 50/60 Hz). 2. Connect one end of the charger to the Intelligent Flight Battery to the Battery Charger. If the battery level is above 95%, turn on the battery before charging. 3. The Battery Level Indicator will display the current battery level as it is charging. 4. The Intelligent Flight Battery is fully charged when the Battery Level Indicators are all off. "JSDPPMUIF*OUFMMJHFOU'MJHIU#BUUFSZBGUFSFBDInJHIU"MMPXJUTUFNQFSBUVSFUPESPQUPSPPNUFNQFSBUVSF before storing it for an extended period. Always turn off the battery before inserting it or removing it from the Phantom 4 Pro / Pro+. Never insert or remove a battery when it is turned on. Power Outlet Charger Intelligent Flight Battery Š 2016 DJI. All Rights Reserved. 29 Phantom 4 Pro/Pro+ User Manual Battery Level Indicators While Charging LED1 LED2 LED3 LED4 Battery Level 0%~25% 25%~50% 50%~75% 75%~100% Fully Charged Aircraft Battery Protection LED Display The table below shows battery protection mechanisms and corresponding LED patterns. Battery Level Indicators while Charging LED1 LED2 LED3 LED4 Blinking Pattern LED2 blinks twice per second Battery Protection Item Over current detected LED2 blinks three times per second Short circuit detected LED3 blinks twice per second Over charge detected LED3 blinks three times per second Over-voltage charger detected LED4 blinks twice per second Charging temperature is too low LED4 blinks three times per second Charging temperature is too high After these issues are resolved, press the Power Button to turn off the Battery Level Indicator. Unplug the Intelligent Flight Battery from the charger and plug it back in to resume charging. Note that you do not need to unplug and plug in the charger in the event of a room temperature error; the charger will resume charging when the temperature is within the allowable range. DJI does not take any responsibility for damage caused by third-party chargers. How to discharge your Intelligent Flight Battery: Slow : Place the Intelligent Flight Battery into the Phantom 4âs Pro / Pro+ Battery Compartment and turn it on. Leave it on until there is less than 8% of power left, or until the battery can no longer be turned on. Launch the DJI GO app to check battery levels. Rapid : Fly the Phantom 4 Pro / Pro+ outdoors until there is less than 8% of power left, or until the battery can no longer be turned on. 30 Š 2016 DJI. All Rights Reserved. Remote Controller This section describes the features of the remote controller and includes instructions for controlling the aircraft and the camera. Š 2016 DJI. All Rights Reserved. 31 Remote Controller 5HPRWH&RQWUROOHU3URĂOH The Phantom 4 Pro/Pro+ remote controller is a multi-function wireless communication device that integrates the dual frequency video downlink system and aircraft remote control system. The 5.8 GHz video downlink is recommended in city to resist interference, while the 2.4 GHz is good for transmission distance in the open area. The remote controller features a number of camera control functions, such as taking and previewing photos and videos, as well as controlling gimbal motion. The battery level is displayed via LED indicators on the front panel of the remote controller. Remote Controller Compliance Version: The remote controller is compliant with local compliance and regulations. Operating Mode: Control can be set to Mode 1 or Mode 2, or to a custom mode. Mode 1: The right stick serves as the throttle. Mode 2: The left stick serves as the throttle. To prevent transmission interference, do not operate more than three aircrafts in the same area. Using the Remote Controller Turning the Remote Controller On and Off The Phantom 4 Pro / Pro+ remote controller is powered by a 2S rechargeable battery that has a capacity of 6000 mAh. The battery level is indicated via the Battery Level LEDs on the front panel. Follow the steps below to turn on your remote controller: 1. When the remote controller is turned off, press the Power Button once. The Battery Level LEDs will display the current battery level. 2. Press and hold the Power Button to turn on the remote controller. 3. The remote controller will beep when it is turned on. The Status LED will rapidly blink green, indicating that the remote controller is linking to the aircraft. The Status LEDs will glow solid green when linking is complete. 4. Repeat Step 2 to turn off the remote controller. Charging the Remote Controller $IBSHFUIFSFNPUFDPOUSPMMFSVTJOHUIFJODMVEFEDIBSHFS3FGFSUPUIFmHVSFPOOFYUQBHFCFMPXGPSNPSF details. 32 Š 2016 DJI. All Rights Reserved. Phantom 4 Pro/Pro+ User Manual Power Outlet Charger Controlling the Camera [4] [3] [1] [2] [1] Camera Settings Dial Turn the dial to adjust camera settings such as ISO, shutter speed, and aperture without letting go of the remote controller. Press down on the dial to toggle between these settings. [2] Shutter Button Press to take a photo. If burst mode is activated, multiple photos will be taken with a single press. [3] Video Recoding Button Press once to start recording video, then press again to stop recording. [4] Gimbal Dial Use this dial to control the tilt of the gimbal. Controlling Aircraft This section explains how to control the orientation of the aircraft through the remote controller. The Remote Control is set to Mode 2 by default. Stick Neutral/Mid-Point: Control sticks are in the center position. Moving the Control Stick: The control stick is pushed away from the center position. Š 2016 DJI. All Rights Reserved. 33 Remote Controller Shoot videos/pictures, view recorded images, and adjust camera settings via the Shutter Button, Camera Settings Dial, Playback Button, and Video Recording Button on the remote controller. Phantom 4 Pro/Pro+ User Manual Remote Controller (Mode 2) Aircraft Indicates Nose Direction) Remarks Moving the left stick up and down changes the aircraftâs elevation. Push the stick up to ascend and down to descend. When both sticks are centered, the Phantom 4 Pro / Pro+ will hover in place. The more the stick is pushed away from the center position, the faster the Phantom 4 Pro / Pro+ will change elevation. Always push the stick gently to prevent sudden and unexpected elevation changes. Remote Controller Moving the left stick to the left or right controls the rudder and rotation of the aircraft. Push the sick left to rotate the aircraft counterclockwise, push the stick right to rotate the aircraft clockwise. If the stick is centered, the Phantom 4 Pro / Pro+ will maintain its current orientation. The more the stick is pushed away from the center position, the faster the Phantom 4 Pro / Pro+ will rotate. Moving the right stick up and down changes the aircraftâs forward and backward pitch. Push the stick up to fly forward and down to fly backward. Phantom 4 Pro / Pro+ will hover in place if the stick is centered. Push the stick further away from the center position for BMBSHFSQJUDIBOHMF NBYJNVN BOEGBTUFSnJHIU Moving the right stick control left and right changes the aircraftâs left and right pitch. Push left to fly left and right to fly right. The Phantom 4 Pro / Pro+ will hover in place if the stick is centered. Press the Intellighent Flight Pause button once to exit from the ActiveTrack, TapFly and Intelligent /BWJHBUJPOnJHIUNPEF5IFBJSDSBGUXJMMIPWFSBU the current position. 34 Š 2016 DJI. All Rights Reserved. Phantom 4 Pro/Pro+ User Manual Adjusting Controller Sticks Hold and twist the controller sticks clockwise or counter clockwise to adjust the length of the controller sticks. A proper length of controller sticks can improve the controlling accuracy. Flight Mode Switch Toggle the switch to select the desired flight mode. You may choose between; P-mode, S-mode and Amode. Position Figure Position 1 Flight Mode P-mode Position 2 S-mode Position 3 A-mode Position 2 Remote Controller Position 1 Position 3 P-mode (Positioning): P-mode works best when the GPS signal is strong. The aircraft utilizes the GPS and Obstacle Sensing System to automatically stabilize itself, navigate between obstacles or track a moving object. Advanced features such as TapFly and ActiveTrack are enabled in this mode. S-mode (Sport): The handling gain values of the aircraft are adjusted in order to enhance the NBOFVWFSBCJMJUZPGUIFBJSDSBGUJO4NPEF5IFNBYJNVNnJHIUTQFFEPGUIFBJSDSBGUJTJODSFBTFEUP 20 m /s in this mode. Note that Obstacle Sensing system is disabled in this mode. A-mode (Attitude): When neither the GPS nor the Obstacle Sensing System is available, the aircraft will only use its barometer for positioning to control the altitude. Enable Multiple Flight Mode by launching the DJI GO app > Camera View > .VMUJQMF'MJHIU.PEFCFGPSFVTJOHUIF*OUFMMJHFOU'MJHIU.PEFGPSUIFmSTUUJNF > Advanced Settings > RTH Button Press and hold the RTH button to start the Return-to-Home (RTH) procedure. The LED ring around the RTH Button will blink white to indicate that the aircraft is entering RTH mode. The aircraft will then return to the last recorded Home Point. Press this button again to cancel the RTH procedure and regain control of the aircraft. Š 2016 DJI. All Rights Reserved. 35 Phantom 4 Pro/Pro+ User Manual Connecting Your Mobile Device Tilt the mobile device holder to the desired position. Press the button on the side of the mobile device holder to release the clamp, and then place your mobile device into the cradle. Adjust the clamp down to secure the mobile device. To connect your mobile device to the remote controller using a USB cable, plug one end of the cable into your mobile device and the other end into the USB port on the back of the remote controller. Remote Controller The Remote Controller of the Phantom 4 Pro+ is provided with a display device to run DJI GO app, you donât need to connect other mobile devices. Optimal Transmission Range The transmission signal between the aircraft and the remote controller is most reliable within the area that is depicted in the image below: Optimal Transmission Range strong weak &OTVSFUIBUUIFBJSDSBGUJTnZJOHXJUIJOUIFPQUJNBMUSBOTNJTTJPO[POF5PBDIJFWFUIFCFTUUSBOTNJTTJPO performance, maintain the appropriate relationship between the operator and the aircraft. Remote Controller Status LED 5IF4UBUVT-&%SFnFDUTUIFTUSFOHUIPGUIFDPOOFDUJPOCFUXFFOUIFSFNPUFDPOUSPMMFSBOEUIFBJSDSBGU5IF RTH LED indicates the Return-to-Home status of the aircraft. The table below contains more information about these indicators. RTH LED Status LED 36 Š 2016 DJI. All Rights Reserved.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : daniel Create Date : 2016:10:28 16:02:56-07:00 Modify Date : 2016:10:28 16:06:49-07:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2016:10:28 16:06:49-07:00 Creator Tool : Adobe InDesign CC (Macintosh) Format : application/pdf Creator : daniel Title : User Manual-3.pdf Document ID : uuid:9ced5956-e081-4b88-b8fa-4495eab1f575 Instance ID : uuid:00377833-89fe-4c3b-ac20-d8e3c37b6ec0 Producer : Acrobat Distiller 10.1.10 (Windows) Page Count : 17EXIF Metadata provided by EXIF.tools