SZ PGST PG101 GSM anti-theft alarm controller User Manual
SZ PGST CO., LTD GSM anti-theft alarm controller
UserManual.wiki
>
SZ PGST
>
PG101 User Manual
User Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![Please insert SIM card and power on the system by adapter, built-in speaker would make a sound, and all icons display on the LCD, the time shows normally after all LED indicators are ON. Signal mark with 5 grids on screen in 10 seconds means host starts up normally with strong GSM signals. Also check whether the signal indicator flashes once every 2s; Finally, move the backup battery switch to ON.-9- -10-GSM anti-theft alarm controller GSM anti-theft alarm controllerFunction Setting1.Initialization Input 4-digit administrator password on the host and press [#] button to confirm. You will hear a voice prompt: please enter instruction. At the same time,［- - - -］displays on the screen, indicating the system enters setting status. You can perform different settings repeatedly as long as the system keeps in setting status. The system will exit setting mode and return to normal status in 35s once you stop doing any operations. 2.System SettingNotes: The system default administrator password is [6666].Operating method: [XXXX] [#] X indicates: 4-digit admin passwordLCD display：3.Exit Setting Press [*] button if you want to exit setting state after finishing setting or return to former operation, the host would make a “tick” sound and setting is finished.Operating method: press [*] button4.Coding of Remote Controller Setting In setup state, input number [21] , then press [#] to confirm. The host make a “tick” sound and you will hear “remote control coding” .the [ ] indicator is on without flashing; Press any button on the wireless remote controller, The host makes a “tick” sound, and then a voice prompts “setting completed”. [ ] indicator goes out, indicating the remote controller succeeds in coding. The code of next remote controller will be displayed on the LCD screen automatically, when coding completed.Operating method: [21] [#]LCD display：Notes: The same remote controller could be coded just once. You can add maximum 5 remote controllers.5.Remote Controller Deleting Setting In setup state, use keypad to enter [22], then press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. Operating method: [22] [#]LCD display：6.Coding of Wireless Detector Setting In setup state, input number [23], and input the defense zone number you want to code [02~99], and then press [#] to confirm. LCD would show the defense zone accordingly. You will hear a voice prompt “detector coding”. Then trigger a wireless detector to emit a wireless signal; after receiving the signal, the host makes a “tick” sound, and then a voice prompts “setting completed”. , the [ ] indicator goes out at the same time.](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-7.png)
![7.Single Wireless Detector Deleting Setting In setup state, enter number [24] and then press the [02~99] defense zone number which needs to be deleted, finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. Notes: The deleted sensor for zone would be invalid, so think it over before you want to delete.-11- -12-GSM anti-theft alarm controller GSM anti-theft alarm controllerOperating method: [23] [XX] [#] XX Indicates：02~99 defense zones numberExample: Code defense zone 02Operating method: [23] [02] [#]LCD display：Operating method: [24] [XX] [#] XX indicates：02~99 defense zones numberExample：Delete defense zone 02Operating method: [24] [02] [#]LCD display：8.All Wireless Detector Deleting Setting In setup state, enter number [25], finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. Notes: The deleted sensor for zone would be invalid, so think it over before deleting.Operating method: [25] [#]LCD display：9.Alarm Type Setting9.1 There are 4 Defense Types:Detector alarm type is set to “0”: This detector will not trigger the host to alarm in any status.Detector alarm type is set to “1”: This detector will trigger the host to alarm whether in Out Arm or Stay Arm state.Detector alarm type is set to “2”: This detector will trigger the host to alarm only in Out Arm state; host is in Stay Arm state, the detector cannot trigger the host to alarm.Detector alarm type is set to “3”: This detector will trigger the host to alarm in any status.9.2 Wireless Detector Alarm Type Setting In setup state, input number [26], and then press the defense zone number [02~99] and then input detector alarm type [0~3], finally press [#] to confirm.The host makes a “tick” sound, and then a voice prompts “setting completed”. Operating method: [26] [XX] [Y] [#] XX indicates: two-digit defense zone number Y indicates: one defense zone alarm typeExample: setting 02 defense zone alarm type to be Out Arm or Stay Arm](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-8.png)
![-13- -14-GSM anti-theft alarm controller GSM anti-theft alarm controllerOperating method: [26] [02] [1] [#]LCD display：9.3 Wired Detector Alarm Type Setting In setup state, input number [47], and press the defense zone number[81~88] and then input [0~3] about detector alarm type, finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. Operating method: [47] [XX] [Y] [#] XX indicates: two-digit defense zone number Y indicates: one defense zone alarm type Notes: wired defense zone of Z1 is equal to zone of 81, wired defense zone of Z2 is equal to zone of 82, wired defense zone of Z8 is equal to zone of 88 in turnExample: alarm type about defense zone of Z2 is set to Out Arm or Stay ArmOperating method: [47] [82] [1] [#]LCD display：10.Wireless Siren Coding Setting In setup state, input [28]+8-digit wireless siren coding, then enter [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. Note: Wireless equipment coding includes sc2262 coding four data bits & 8 address bits.Operating method：[28] [XXXXXXXX] [#] XXXXXXXX indicates：8-digit wireless siren codingExample: detailed operating of wireless equipment coding is“01020102”Operating method：[28] [01020102] [#]LCD display：11. Remotes Operation Voice Prompt Setting In setup state, input number [31], and then input 0/1 , finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. Factory defaults: turn on the voice[ ]Operating method：31] [X] [#] X =“0” indicates：Voice prompt turns off X =“1” indicates：Voice prompt turns onExample: Turn on remotes voice promptOperating method：[31] [1] [#][LCD display：](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-9.png)
![-15- -16-GSM anti-theft alarm controller GSM anti-theft alarm controller12.Siren Ring Time Setting In setup state, enter [32], then input time [00~15] minutes, finally press [#] to confirm; The host makes a “tick” sound, and then a voice prompts “setting completed”. Default: 3 minutesOperating method: [32] [XX] [#] XX indicates: siren ring time, unit: minuteExample: Set 2 minutes of siren ring timeOperating method: [32] [02] [#]LCD display：14.Defense Zone Alarm Time Delay Setting In setup state, enter [34], then input defense zone [02~99], last input delayed time [00~99] seconds, press [#] to confirm; The host makes a “tick” sound, and then a voice prompts “setting completed”. Default: no delayOperating method: [34] [XX] [YY] [#] XX indicates：Defense zone YY indicates：Delayed alarm time, unit: secondExample: Detailed operating of 5 seconds delayed alarm time for defense zone 05Operating method: [34] [05] [05] [#]LCD display：13.Arm Time Delay Setting In setup status, enter [33], then input delayed time [00~99] seconds, finally press [#] to confirm; The host makes a “tick” sound, and then a voice prompts “setting completed”. Thus arm time delayed setting is finishedOperating method: [33] [XX] [#] XX indicates：Arm delayed time, unit: secondExample: detailed operating of 2 seconds delayed time armOperating method: [33] [02] [#]LCD display：15.Telephone Dial-up Cycle Times Setting In setup state, enter [35], then input dial-up times [00~09], finally press [#] to confirm; next the host makes a “tick” sound, and then a voice prompts “setting completed”. Default: 9 times Operating method: [35] [XX] [#] XX indicates: Telephone dial-up cycle timesExample: Detailed operating about 2 cycle timesOperating method: [35] [02] [#]LCD display：](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-10.png)
![16.Remote Call Ringing Times Setting In setup state, enter [36], then input ringing times [0~9], finally press [#] to confirm; The host makes a “tick” sound, and then a voice prompts “setting completed”. Default: 6 timesOperating method: [36] [X] [#] X indicates：ring times;Example: Detailed operating of 2 times remote call ringingOperating method: [36] [2] [#]Notes: The host remote control is closed, when ringing times is set to 0LCD display：-17- -18-GSM anti-theft alarm controller GSM anti-theft alarm controller18.Password Change Setting18.1Change User Password In setup state, use keypad to input [38], then input the 4- digit new password, finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”.Default:1234.Operating:[38] [XXXX] [#] XXXX indicates：the new 4-digit passwordExample: change the system password to 1012Operating: [38] [1012] [#]LCD display：18.2Change Administrator Password In setup status, use keypad to input [39], then input the 4- digit new password, and then press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”.Default:6666Operating: [39] [XXXX] [#] XXXX indicates: the new 4-digit passwordExample: change the system password to 2846Operating: [39] [2846] [#]LCD display：17.Recording SettingOperating method: [37] [#]LCD display： In setup state, use keypad to input [37], and then press[#] to confirm. The host will emit a “tick” sound and the [ ] indicator is on, and after 10 seconds count down, recording starts: record at 30cm away from the host with moderate tone; 10 seconds later, the host will make a “tick”sound, indicating the recording finish. Meanwhile, the recorded voice will replay.Notes: The user password and the Administrator password cannot be the same.](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-11.png)
![-19- -20-GSM anti-theft alarm controller GSM anti-theft alarm controller19.Host Keypad Lock Setting In setup state, enter [40], then input [0/1], finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”.Operating: [40] [X] [#] X=“0” indicates: off X=“1” indicates: on Example: Open the keypad lockOperating: [40] [1] [#]LCD display：21. Host Timing Arm /Disarm Setting In setup state, enter [42], and then input disarming time [AABB], and then input arming time [XXYY], finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”.Operating: [42] [AABB] [XXYY] [#] “AABB” indicates: disarming time—hour and minute “XXYY” indicates: arming time—hour and minuteExample: set disarming to 8:20 and arming time to 20:30Operating: [42] [0820] [2030] [#]LCD display：20.Host Timing Arm/Disarm Enable/Disable Setting In setup state, enter [41], then choose on/off auto Arm or Disarm function key［1/0］, finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. Factory default: off.Operating: [41] [1/0] [#] X=“0” indicates: off X=“1” indicates: onExample: Turn on timing Arm/Disarm functionOperating: [41] [1] [#]LCD display：22.Host Reset Setting In setup status, first enter [43], then press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”.(Remote controllers and detectors would not be deleted).Operating: [43] [#]LCD display：](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-12.png)
![-21- -22-GSM anti-theft alarm controller GSM anti-theft alarm controller23. Host Logs Inquires In setup state, first enter [44], then press [#] to confirm; The host will make a “tick” sound and then enter into records list. Press “2” to page up and press “8” to page down. There are 10pcs of alarm logs in total.Operating: [44] [#]LCD display：24. Host Logs Deleting In setup state, first enter [45], then press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. Thus host logs are removed. Operating: [45] [#]LCD display：25.SMS Notification of Arm/Disarm In setup state, first enter [46], then choose command key[0/1], that means whether to send SMS to the user when Arm or Disarm, finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. Default: not send Operating: [46] [X] [#] “X=1” indicates: send. “X=0” indicates: not sendExample: send out SMS to user's mobile phone Operating: [46] [1] [#]LCD display：26. System Clock Setting In setup state, use keypad to input [48], then input the last 2 digits [YY] of the present year, and then the 2 digits [MM] of the month, and then the two digits [DD] of the date, and then the two digits [hh] of the hour (24-hour system), and then the two digits [mm] of the minute, and finally enter [#] to confirm. You will hear a “tick” sound and a voice prompt: “setting completed”.Operating: [48] [YY] [MM] [DD] [hh] [mm] [#] “YY” indicates: the last 2 digits of the present year “MM” indicates: the 2 digits of the present month “DD” indicates: the 2 digits of the present date “hh” indicates: the 2 digits of the present hour(24 hour system) “mm” indicates: the 2 digits of the present minuteExample: set the time as 17:30, June, 12th, 2012Operating: [48] [12] [06] [12] [17] [30] [#]LCD display：](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-13.png)
![-23- -24-GSM anti-theft alarm controller GSM anti-theft alarm controller27.SMS Phone Number Setting In setup state, enter [49~50], then input phone number, finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”.Note: input [49] to set the first SMS phone number, input [50] to set the second SMS phone Operating: [XX] [YY…YY] [#] XX indicates: address code [49-50] of 1-2 group SMS alarm phone number YY…YY Indicates: phone numberExample: set 13911112245 to be the first group alarm phone numberOperating: [49] [13911112245] [#]LCD display：28.SMS Phone Number Deleting In setup state, enter [49~50], finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”.Operating: [49] [#]Example: Deleting the first SMS alarm phone numberOperating: [49] [#]LCD display：29.Alarm Phone Number Setting In setup state, enter [51] ~ [56], then input phone number, finally press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”.Operating: [XX] [YY…YY] [#] XX indicates: address code [51] ~ [56] of 1-6 group alarm phone number YY…YY indicates: phone numberExample: set 13811110751 to be the first group alarm phone numberOperating: [51] [13811110751] [#]LCD display：30.Alarm Phone Number Deleting In setup state, enter [51] ~ [56], then press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”.Operating: [XX] [#] XX indicates: address code [51] ~ [56] of 1-6 group alarm phone numberNotes: Only the pre-set alarm phone number can realize remote control.](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-14.png)
![-25- -26-GSM anti-theft alarm controller GSM anti-theft alarm controllerExample: deleting the first group alarm phone numberOperating: [51] [#]LCD display：31.Defense Zone Alarm Type Setting In setup state, first input address code [60] , choose the corresponding defense zone code [02~99] , and then input [1~8] defense zone alarm type, finally press [#] key to confirm. Voice prompts: setting completed.Operating: 【60】 【XX】 【 A 】 【 # 】 XX indicates defense zone code: [02~99] matching 02 to 99 defense zones correspondinglyA represents alarm type: [1] SOS Alarm, [2] fire alarm, [3] gas leak alarm, [4] door lock alarm, [5] hall alarm, [6] window alarm, [7] balcony alarm, [8] perimeter alarm.Example: set defense zone 10 to be fire alarm typeOperating: 【60】 【 10 】 【 2 】 【 # 】 LCD display：32. Host GSM Signal Checking In setup state, enter [62] and then press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. GSM signal value is displayed.Operating: [62] [#]LCD display：33. LCD Backlight Duration Setting In setup state, enter [63] and input [00-99] seconds, then press [#] to confirm. The host makes a “tick” sound, and then a voice prompts “setting completed”. Default time: 20 seconds.Operating: [63] [XX] [#]XX indicates: backlight lasting timeExample: set time to 49sOperating: [63] [49] [#]LCD display：](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-15.png)
![Download APP iPhone user enter the APP Store, search "GSM alarm system"then download and install this software.Android user enter Google Play or Android market (China mainland), search “GSM alarm system”,then download and install this software.-27- -28-GSM anti-theft alarm controller GSM anti-theft alarm controller34.Sound Volume Setting In setup status, enter [64]，then input volume level [0~9]，press [#]to confirm. Once the host makes a “tick” sound, you will hear a voice prompt“setting completed”.Default level “6”.Operating method: [64] [X] [#] X indicates: volume levelExample: level 2Operating：[64] [2] [#]Note: If the volume level is set“0”,then no sound.LCD display：35. Language Setting In setup status, enter [65]，then input [1~2], press [#]to confirm. Once the host makes a “tick” sound, you will hear a voice prompt“setting completed”. Default language Chinese[2].Operating method: [65] X] # X indicates: LanguageExample: English [1]Operating：[65] [1] [#][ [ ]LCD display：Mobile APP Operation The system can be controlled by APP. iOS mobile will map to SMS interface, Android mobile won’t map to SMS interface, but will finish the SMS operation in background.iPhone APP interface Android APP interface](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-16.png)
![In the state of factory defaults, user can control the panel remotely on the SMS interface of the APP from any mobile phone. The panel only receive the APP command from the pr-set numbers which have been stored in it.App Use(1)Add host accountiOS mobile: Press [Edit], then press [Delete], the added host account will be deleted.Android mobile: Press [Edit], long press the host account, then will come out the dialog window of deleting account, press[Finish], the added account will be deleted.-29- -30-GSM anti-theft alarm controller GSM anti-theft alarm controller(2)Main interface operation Press the pr-set host account, enter into Main Menu,then user can operate the functions of disarm,out arm, stay arm,dial back and monitor and so on. Press the pr-set host account, enter "System Setting", then user can use app to remotely setup the host parameter including "Host Alarm Phone Number Setting " (6 groups), "Host SMS Number Setting”( 2 groups), “Naming Defense Zone", "Call Ringing Time", "Alarm Time Delay", "Siren Ring Time Setting", "Host Timing Arm or Disarm Setting" and other operations.Notes: For “Naming Defense Zone”,you can only change 2 zones. If naming in Chinese, the characters are no more than 10. Naming in English, the characters are no more than 40. If operate by app,you must save your phone number in host panel first or it will not work.(3)Delete Account](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-17.png)
![Operating: press [Out Arm ] of remote controller.The Host Operating: [Out Arm ] (keypad lock is closed or [Out Arm ] + [user password] + [#] (keypad lock is open) .SMS operation: Edit SMS “1” and send it to the SIM number of host with your mobile phone. Out Arm means the host’s whole defense zones are in Arm state. In other words, when no one in the house, all detectors would work and detect all deleting areas, when there are detection sources(thieves invasion fire,gas leakage,etc.)trigger detector,the system makes alarms immediately. If the function of the keypad lock is closed, press the Out Arm [ ], the host will go into Out Arm state; If the function of the keypad lock is open, press the Out Arm[ ]while this operation need to input user’s password then to realize Out Arm.Emergency Alarm: No matter in which status, press the[ ]key of remote controller, system will enter into alarm state at once.Stay Arm: press [ ]key, host releases prompt:“system armed”,Stay Arm indicator LED on,all the defense zones enter into Stay Arm state.Disarm: Press [ ] key,host releases prompt: “System disarmed”, Disarm indicator LED on, all the defense zones enter into Disarm state.Press[ ] key, host releases prompt: “System armed”, Out Arm indicator LED on, all the defense zones enter into Out Arm state. -31- -32-GSM anti-theft alarm controller GSM anti-theft alarm controllerDaily Operation Remote controller is one kind of device which carries out mufti-function operation by radio. Its function is convenient for user to control its state when he is at the door (outdoor) or long-distance, such as Out Arm, Stay Arm , Emergency Alarm , Disarm functions etc.Out Arm keyStay Arm keyDisarm keyEmergency Alarm keyOut ArmStay ArmDisarmEmergency Alarm1.Out Arm It means, for the safety, while somebody is at home, you need to enable the peripheral: door, window, balcony and boundary detectors of the alarm system while prevent from triggering the indoor detectors, which may cause improper warning; then, you shall select Stay Arm, let just part of the detectors work and disable the other parts.2.Stay ArmLCD display： Remotes Operation: Just press [ ] onceSMS operation: Edit SMS “0” and send it to the SIM number of host with your mobile phone.LCD display：](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-18.png)
![To create SMS instructions to alarm host through the mobile phone, then to remote control the host, make host enter into Arm or Disarm state; Also can open or close the Siren.Detailed SMS instructions as follows: Host Arm SMS instruction: Edit SMS “1” and send it to the SIM number of host with your mobile phone, If you get back the message "Armed" from the host which means the host has entered into Arm state. Host Disarm SMS instruction: Edit SMS “2” and send it to the SIM number of host with your mobile phone, If you get back the message "Disarmed" from the host which means the host has entered into Disarm state. Open Siren SMS instruction: Edit SMS “6” and send it to the SIM number of host with your mobile phone, If you get back the message "Siren On" from the host which means the siren has sounded already. Close Siren SMS instruction: Edit SMS “5” and send it to the SIM number of host with your mobile phone, If you get back the message "Siren Off" from the host which means the siren has been closed already.5.Remote Control by SMS Remotes Operation: Press [ ]button.Host Operation: Press[ ]buttonSMS operation: Edit SMS “2” and send it to the SIM number of host with your mobile phone. Disarm means to make the alarming host into non-alert state. One is, to Disarm the host from Arm state; the other is, to stop the alarm when the host is making alarms. After disarming, even if you trigger the detector, the host would not sound alarm (excluding 24- hour defense areas). If keypad lock is closed, press [ ]keypad directly to disarm. If keypad lock is open, press [ ], and follow voice prompt enter [user password, finally press [#] to confirm. [Out home] or [Home] signal light is off. Disarming operation is completed.3.DisarmLCD display：Note: Please press # to stop the calling of alarm.-33- -34-GSM anti-theft alarm controller GSM anti-theft alarm controller When the host make alarms, siren releases voice prompt at once. First, it would send out SMS, telling user which defense zone has alert, then it will dial the preset numbers to make voice alarm. If no one answers the call, the system will call the next user number automatically. The system will call each preset numbers for 3 times in order. If you answer the call, you will hear the pre-record voice. You can set system to realize various functions via your telephone or mobile phone keypad. Hang up: If you hang-up directly without answering the call, system will call each preset number circularly. Press [*]: Play the recording. Press [1]: The host stops alarming and to Arm; it stops calling users. Press [2]: The host stops alarming and to Disarm; it stops calling users. Press [3]: The host closes siren and monitors the scene for 30 seconds, for continuous monitoring, press [3] again to monitor the abnormal sounds or a burglar intrusion for another 30 seconds. Press [4]: start talk-back 30s.4. Answer Alarm Call The telephone (mobile) is connected to alarm host number, and after setting of ringing times, the telephone receiver prompts computer-generated voice: “Please enter password”. The password is entered via telephone (mobile). For wrong password, the host gives prompt: “wrong password, please enter password again”. For correct password, the telephone receiver prompts “press ① to arm, press ② to disarm, press ③ to monitor, press ④to talk ”. And after getting access of remote control, phone button could be used for remote control. Press [*]: play the recording. Press [1]: the host stops alarm and enter into Arm state Press [2]: the host stops alarm and enter into Disarm state Press [3]: the host closes the siren, enter into monitoring state for 30 seconds and press [3] for another 30 seconds to monitor the abnormal sounds or a burglar intrusion in case of continuous monitoring. Press [4]: start talk-back 30s.6.Remotely Control Some special cases occur in the family: sudden illness for the elderly or children results in first aid; in case of sudden fire, help is needed; in case of housebreaking, the alarm is required; So please just press the host keypad “Emergency Alarm[SOS]” ,remote controller key [ SOS ]. Alarm system will immediately sound loudly and automatically call the pre-set phone number.7.SOSNotes: Please press “ #” to stop the calling of alarm.Remotes operation: press [SOS]buttonHost operation: press [SOS] button on keypad](https://usermanual.wiki/SZ-PGST/PG101/User-Guide-3310132-Page-19.png)
