Samsung Electro Mechanics SWL-2000N PCMCIA Card User Manual Manual

Samsung Electro Mechanics PCMCIA Card Manual

UserManual.wiki >

Samsung Electro Mechanics >

SWL-2000N User Manual >

manual

1. manual
2. Manual

manual

2Notice 2The SWL-2000N complies with Part 15 of the FCC rules.Operation is subject to the following two conditions; (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.Note: The SWL-2000N has been tested and found to comply with the limits for a Class Bdigital device and a low power transmitter, according to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee that interference willnot occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on,the user is encouraged to resolve the problem by one or more of the following measures;- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and the receiver.- Connect the equipment to an output on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.

3Important Safety Informationl Read these simple guidelines. Breaking the rules may be dangerous or illegal. SAMSUNG is notresponsible for any damages caused by breaking the rules.l Wireless LAN Card described in this document is approved for use in a wireless local areanetwork.l Remember to make backup copies of important data.l When you are transferring data, keep your laptop computer stationary. Roaming between accesspoints may break the connection.l Only qualified service personnel must repair the equipment.l All wireless devices may get interference, which could affect performance.l Use approved accessories only. Do not connect incompatible products.l Use only accessories approved by the wireless LAN Card manufacturer for use with thisparticular wireless LAN Card. The use of any other types will invalidate any approval orwarranty applying to the wireless LAN Card, and may be dangerous,l Use only the region setting appropriate for the area where the wireless LAN Card is used at thepresent time. Using the card in any other region or with an incorrect region setting is prohibitedand may be illegal.l Operation of any radio transmitting equipment, including a wireless LAN Card, may interferencewith the functionality of inadequately protected medical devices.l Do not use the wireless LAN Card on aircraft.l Do not use the wireless LAN Card at a refueling point.l Do not use the wireless LAN Card near fuel or chemicals.l Do not use the wireless LAN Card where blasting is in progress.l Do not use the wireless LAN Card when the use of wireless device may cause interference ordanger.l Do not use the wireless LAN Card where the use of cellular terminals is prohibited.

4Table of Contents1. MagicLAN Installation ……………...…………………………………………………... 71.1 Introduction …………………………..……………………………………………...71.2 Technical Background ……………………..……………………………………….. 71.3 MagicLAN Overview ……………………………..………………………………. 102. Before Installation ……………………………………………………………………... 112.1 What’s in your Package …………………………………………………………… 112.2 System Requirement ……………………………………………………………… 113. MagicLAN Installation for Windows95/98 ……………………………………………. 123.1 Installation Overview ……………………………………………………………… 123.2 Hardware Installation ……………………………………………………………… 133.2.1 Notebook PC Adapter Card (SWL-2000N) ………………………………….. 143.2.2 Access Point (SWL-2000AP) ………………………………………………... 143.3 Software Installation ……………………………………………………….……… 153.3.1 Driver Setup ………………………………………………………………….. 153.4 MagicLAN Wireless LAN Card Properties Setup ………………………………… 203.4.1 Before Wireless LAN Card Properties Setup ………………………………... 203.4.1.1 Basics regarding the Properties Setup ……………………………………….. 203.4.1.2 Meanings of the Properties Setup Options …………………………………… 203.4.2 Setting Network Properties for “Peer-to-Peer” mode ………………………... 213.5 Network Configuration Setup ……………………………………………………... 233.5.1 Network Configuration Setup Overview …………………………………….. 233.5.2 Before TCP/IP Networking Configuration Setup …………………….……… 233.5.2.1 What you should know before Configuration ………………………………... 233.5.2.2 What you should have in your hands to proceed further …………………….. 243.5.3 Setting Network Properties for “StructureNet” mode ……………………….. 253.5.4 Setting Network Properties for “Instawave” mode ………………………….. 263.5.5 TCP/IP Networking Configuration Setup …………………………….……… 273.5.5.1 TCP/IP Installation …………………………………………………………… 273.5.5.2 TCP/IP Properties Setup ……………………………………………………... 304. MagicLAN Installation for Windows NT ……………………………………………… 34

54.1 Hardware Installation ……………………………………………………………… 344.2 Software Installation ……………………………………………………….……… 344.2.1 When there is no Windows NT Networking installed yet …………………… 344.2.2 When there is Windows NT networking already installed …………………... 445. Packet Driver Installation for MS-DOS ……………………………………………….. 525.1 Copy the Packet Driver ……………………………………………………………. 525.2 Setup AUTOEXEC.BAT ………………………………………………………….. 525.3 Setup MAGICWAV.CFG ………………...……………………………………….. 526. Access Point(AP) Installation ………………………………………………………….. 566.1 Before Access Point(AP) Installation ……………………………………………... 566.1.1 Access Point(AP) …………………………………………………………….. 566.1.2 What you need for the Installation …………………………………………… 566.2 Access Point(AP) Installation ……………………………………………………... 566.2.1 Access Point Setup using Null Modem Cable ……………………………….. 566.2.2 Access Point Setup without Null Modem (Cold Start Mode) ……………….. 596.3 Configuration Setup ……………………………………………………………….. 596.4 Parameter Setup …………………………………………………………………… 606.5 Null Modem Cable Configuration ………………………………………………… 626.6 Diagnostic Methods ……………………………………………………………….. 627. Management Utilities(Web & Telnet) …………………………………………………. 637.1 About Management Utilities ……………………………………………….……… 637.2 Hyper Terminal Management Utility ……………………………………………... 637.3 Web Management Utility ………………………………………………….………. 637.3.1 Web Management Utility Overview ………………………………….……… 637.3.2 AP Status Report(http://xxx.xxx.xxx.xxx) …………………………………… 647.3.3 AP Statistics(http://xxx.xxx.xxx.xxx/stats.htm) ……………………………... 657.3.4 AP Configuration Settings(http://xxx.xxx.xxx.xxx/config.htm) …….………. 677.3.5 Access Point Bridge Table Report(http://169.79.60.26/tables0000.htm) ……. 687.4 TELNET Management Utility …………………………………………………….. 707.4.1 Telnet Management Utility Overview ……………………………………….. 707.4.2 Various Commands and Usage ……………………………………….……… 707.4.2.1 Usage of the command line …………………………………………………... 707.4.2.2 All Possible Commands ……………………………………………………… 707.4.2.3 Explanation on various Commands ………………………………………….. 71

68. Miscellaneous Features ………………………………………………….……………... 738.1 Connection Check ………………………………………………………….……… 738.1.1 When successfully connected to Network through AP ……………….……… 738.1.2 When failed to connect to Network through AP ……………………………... 738.2 Performance & AP Information Check ……………………………………………. 738.3 Brief Troubleshooting ……………………………………………………………… 748.4 Specifications ………………………………………………………………………. 75 8.4.1 Physical Specifications ……………………………………………….……… 75 8.4.2 Radio Characteristics ………………………………………………………… 75 8.4.3 Network Characteristics ……………………………………………………… 75

71. MagicLAN Introduction1.1 IntroductionThank you for your purchase of SAMSUNG MagicLAN (SWL-2000N) Wireless LAN Adapter.. Installingcard allows the computer to join a wireless network based on the IEEE 802.11 wireless LAN standard. Youwill be surprised how easy for you to be a part of network with no bother of twisted cables.1.2 Technical Background• What is IEEE 802.11?The IEEE 802.11 specification is a wireless LAN standard developed by the IEEE (Institute of Electrical andElectronic Engineering) committee in order to specify an “over an air” interface between a wireless clientand a base station or Access Point, as well as among wireless clients.Like other IEEE 802 families, IEEE 802.11 specification addresses both Physical (PHY) layer and MediaAccess Control (MAC) layer.• IEEE 802.11 Physical (PHY) LayerAt the PHY layer, IEEE 802.11 defines three physical characteristics for LAN: diffused infrared, DirectSequence Spread Spectrum (DSSS), and Frequency Hopping Spread Spectrum (FHSS). While the infraredPHY operates at the baseband, the other two PHYs operate at the 2.4GHz ISM (Industrial, Scientific, andMedical) band, which can be used for operating wireless LAN devices without the need for end-userlicenses. In order for wireless devices to be interoperable, they have to be conform to the same PHYstandard.• IEEE 802.11 Media Access Control (MAC) LayerThe IEEE 802.11 MAC Layer is mainly concerned with rules for accessing the wireless medium. There aretwo network architectures defined: StructureNet Network and Peer-to-Peer Network.

8• Peer-to-Peer NetworkPeer-to-Peer Network is an architecture that is used to support mutual communication among wirelessclients only. Since Peer-to-Peer Network does not support access to wired networks, it does not need anAccess Point to be a part of the network. You can use the network immediately after setting up the operatingmode using the supplied network driver.• StructureNet NetworkStructureNet Network is architecture to provide communication between wireless clients and wired networkresources. The transition of data is defined by an Access Point (AP) and the associated wireless clients. So awireless client can access all the services that are available for a regular wired LAN by using Access Point(AP).• Instawave NetworkInstawave Network is architecture to provide both Peer-to-Peer Network features and StructureNet Networkfeathers at the same time. In other words, wireless clients on the network can directly communicate witheach other while they can also access wired LAN clients through AP if they want. Instawave Network is agood choice for small networks that need maximum flexibility and simplicity.

9• RoamingRoaming is a service that allows wireless clients to use the network in motion by automatically moving theconnection to an old Access Point into a new Access Point when the clients enter into a new cell.• Scanning, Beaconing & ESS IDWhen a wireless client is initialized, it is necessary for it to find and communicate with the correct group forwireless devices, including Access Point (AP). At this point, it may search for all the frequency channels andthis process is called “scanning.”There may be multiple APs and network operating at the same time. It may be necessary to ensure that thestation joins with the correct network during the scanning process. To achieve this, each AP is assigned tobe part of a logical group called the Extended Service Set (ESS). The name of this logical group is the ESSID. When roaming is operating, there may be several Access Points as part of the same ESS.After powering up, the wireless client will listen on its default frequency channel. It will be listening for“beacons” sent by another wireless station or AP. Here, a beacon is a short message containing the ESS IDthat will be broadcast roughly ten times a second.When the wireless station hears a beacon, if the ESS ID in the beacon matches its own, the client knows thatit is on the correct channel and can communicate with its group. If no beacons are seen, or if the ESS IDdoes not match, the wireless client may move to the next frequency channel and repeat this listeningprocedure. If all frequency channels have been searched with no matched ESS ID found, it will assume thatit is the first client in the group to wake up and will return to its default channel and start to issue beaconsitself.In DSSS, this scanning process occurs at start up and may also occur when the client roams between APs.

101.3 MagicLAN Overview• The SWL-2000N (for Notebook) is a wireless LAN adapter card that provides wireless connection betweenPCs.• The MagicLAN is designed to operate with IEEE 802.11 (wireless LAN International Standard) wirelesscompliant radio cards and uses a CSMA/CA (Collision Sense Multiple Access with Collision Avoidance)algorithm as the media access scheme, which makes high speed communication with minimal collisionpossible.• The MagicLAN supports DSSS (Direct Sequence Spread Spectrum). This is a radio technique, whichscrambles the data prior to transmission and uses a correlation technique on receiving to improve the signalto noise ratio and makes it possible to communicate in the office having a wall and a compartment.• The function of the MagicLAN SWL-2000AP (Access Point) is to transfer information from a wired LANto a wireless LAN and vice versa. When operating, the MagicLAN AP is invisible to most users (Normally,unless the user is an administrator, the MagicLAN AP cannot be seen or accessed by users on the network).• The SWL-2000N for Notebook PC is small and portable as a roaming function is provided for users whoneed network services while maintaining mobility.• The MagicLAN Adapter has three LED’s (Light Emitting Diodes) on the part of the card: Power, Tx, andRx. The red Power LED will illuminate when the power is applied. The orange Tx LED and green Rx LEDwill illuminate when the date is transmitted out and in respectively.• The MagicLAN supports various network software. The network driver is provided to support mostnetwork software such as MS-DOS Packet, Windows 95/98, and Windows NT 3.51/4.0.

112. Before the InstallationThe following section will assist you in successfully installing your wireless network adapter card. You willfirst install the hardware and software, then set network properties to accommodate resource sharing and toselect the type of wireless network you wish to install. The MagicLAN can be easily installed and used,without bother to connect cables and maintain them to use network as a wired LAN requires.2.1 What’s in Your PackagePlease check the contents of the box to make sure everything is included and ready for use. Here is the list ofwhat you should have in your package: • SWL-2000N (PCMCIA Card) Adapter • SWL-2000N Installation Diskette (Driver Diskette) • User’s Manual • SWL-2000AP (Each Access Point requires a SWL-2000N adapter card for operation) • Power Adapter (SWL-2000AP only) • SWL-2000AP Utilities Diskette (SWL-2000AP only) • External Antenna (Optional)2.2 System Requirement• Operating System: MS Windows 95 / Windows 98 / Windows NT3.51/ Windows NT4.0• Computer System with a 31/2-inch floppy disk drive• For Notebook PC Adapter Card (SWL-2000N): The computer system should have PCMCIA Type II or Type III card slot.

123. MagicLAN Installation for Windows 95/983.1 Installation OverviewHere are some steps you will perform in establishing your wireless network connection: • Install the hardware. - For the StructureNet mode, you must install an Access Point (SWL-2000AP) first. Then install the adapter (SWL-2000N). • Install the software using the included installation diskette. • Install the network protocol(s) required to communicate on your network. Most likely you will need the TCP/IP protocol.

133.2 Hardware Installation3.2.1 Notebook PC Adapter Card (SWL-2000N) • You can install the card whether the power of the Notebook is on or off.• Insert the SWL-2000N adapter card into the PCMCIA slot. (A pleasant “cheep” sound indicates the regular operation. A low monotonous tone indicates a failure in recognition.)• If you see red Power LED illuminating and green Rx LED is blinking, you are now ready to proceed to software setup.3.2.2 Access Point (SWL-2000AP)• An Access Point is equipped with an Ethernet adapter supporting 10base-T, 10base 2 and a MagicLAN wireless LAN adapter card.• Insert the MagicLAN card (SWL-2000N) into the PCMCIA slot of the Access Point (SWL-2000AP)• Connect the network cable to Ethernet port (10base-T or 10base 2) on the back of the Access Point.

14• Connect the power adapter, and now you are ready to use the MagicLAN Access Point.

153.3 Software Installation3.3.1 Driver Setup(The dialog box pictures used in this section is from Windows 98, and the ones from Windows 95 may beslightly different.)1. Start your PC and allow Windows95/98 to fully load. Since you must already have installed theMagicLAN Adapter in the previous step, an “Add New Hardware Wizard” box will appear.2. If you use PCMCIA-compatible notebook and have not installed the SWL-2000N adapter yet, insert theadapter to the slot now, and you will see an “Add New Hardware Wizard” box.3. In “Add New Hardware Wizard” box, be sure SAMSUNG-WirelessLAN appears as a new device nameas the following box shows. 4. Insert the MagicLAN (SWL-2000N) Installation Diskette into your floppy drive. Click on “Next”.

165. Windows 95/98 will present a list of drivers and optionally allow you to specify a location where it can find the appropriate driver software for the device. The following dialog box will appear if you use Windows98. Be sure the MagicLAN (SWL-2000N) Installation Diskette is in floppy drive and “Search for the… (Recommended)” option is selected. Click on “Next”. (Windows95 has a slightly different display, and you should select a “Have Disk” option instead.) 6. Next, “Add New Hardware Wizard” box may appear as follows. Be sure the MagicLAN (SWL-2000N) Installation Diskette is in floppy drive and Floppy disk drives option is checked as follows. Click on “Next”.

177. If the proper driver was successfully found on the floppy disk, “Add New Hardware Wizard” box may appear as follows. Click on “Next”. 8. Windows95/98 will now copy files from the floppy disk and may prompt you for the location for the Windows95/98 installation CD or files. Depending on how your computer was configured by the manufacturer, you may need to insert the Windows CD into your CD-ROM drive at this step. While files are being copied, you will see “Copying Files…” box similar to the one below.

$189. While copying files, the following box may appear requesting you to specify where the some files are located. In the drop-down choice box below, select “A:\” where the MagicLAN (SWL-2000N) Installation Diskette is located. Click on “OK”. 10. When the driver and all the required Windows95/98 software components are loaded, you will see the box similar to the one below, which indicates that the driver for “SAMSUNG Wireless LAN Card” has been successfully installed. Click on “Finish”.$

1911. Finally, “System Settings Change” box will appear, asking if you wish to restart your computer now. Remove the MagicLAN (SWL-2000N) Installation Diskette from your floppy drive. Since you are done with the Installation Diskette, place it in a safe place for later use. Now, Click on “No” to proceed to MagicLAN Wireless LAN Card Properties Setup before you restart your computer.

203.4 MagicLAN Wireless LAN Card Properties Setup3.4.1 Before MagicLAN Wireless LAN Card Properties Setup3.4.1.1 Basics regarding the Properties Setup• Peer-to-Peer Operating Mode: Multiple wireless clients can directly communicate with each other without AP.• StructureNet Operating Mode: Wireless clients can communicate with each other or with clients on another wired network always through AP.• Instawave Operating Mode: Multiple wireless clients using the same channel can directly communicate with each other, And they also can communicate with clients on another wired network through AP. In the second case, it is automatically set up which AP will be used for it.• Roaming: One feature of StructureNet operating mode that effortlessly moves between APs that are on different channels but have the same ESS ID.• From your network administrator, you should find out ESS ID of the AP and channel number that you are supposed to use.3.4.1.2 Meanings of the Properties Setup Options• Default Scanning / Start Channel: Option in StructureNet and Peer-to-Peer Network) StructureNet operating mode enables clients to automatically search for new Access Point. In Default Scanning mode, the wireless client begins the search with Channel 1. The client then searches all consecutive channels until it finds a new AP with the same ESS ID. If you want to start the search from a specific channel other than channel 1, you can deselect the Default Scanning check box and enter the desired channel number in a blank for Start Channel. This Start Channel entry will be helpful when multiple APs are within range of each other and you desire to connect to a specific AP among them.• Enable Power Saving: Option in StructureNet Network Power save mode will keep the wireless LAN adapter in a low power standby state when there is no data transfer. This Enable Power Saving option is mainly to extend the operating time of portable battery operated device such as laptop computers, even sacrificing the effective throughput of the wireless connection. So you should test both with and without power saving enabled to see if this option satisfies your needs.

21• Case sensitive ESS ID: Option in StructureNet and Peer-to-Peer Network When entering ESS ID, you can make it case sensitive by checking Case sensitive ESS ID check box.• Auto join: Option in StructureNet and Peer-to-Peer Network When Auto join option is selected, the wireless client will associate with whatever access point is within range and has the best signal independent of the ESS ID setting. Since you may not use the same AP as described in the “Access Point Client Properties” box, you can check which AP and ESS ID you are actually using by double clicking the task bar status icon to display the wireless client status box.3.4.2 Setting Network Properties for “Peer-to-Peer” mode1. Right click on your “Network Neighborhood” icon and click on “Properties”.2. “Network” box will appear with Configuration tab selected as follows. In the list in the box, click on “SAMSUNG Wireless LAN Card” and “Properties” button in the middle sequentially.

223. “Access Point Client Properties” box will appear as follow. 4. Check the Peer-to-Peer radio button in Operating Mode list.5. Enter the desired ESS ID you are authorized to use. (ESS ID is set to “MagicLAN” as default, but you can change it to another.)6. Select the desired Channel you are authorized to use.7. Change some options if you want.8. Click on “OK” to finish up the setup.9. “System Setting Change” box will appear as follows. Click on “No” to proceed to Network Configuration Setup before you restart your computer.

233.5 Network Configuration Setup3.5.1 Network Configuration Setup Overview• After you finish up the hardware and software driver setup, you will need to install and configureMicrosoft Networking components.• If you only need to access the Internet, installation of the TCP/IP networking component should besufficient.• If you want some functions to share files and printers in small LAN environment, some installations mayuse an alternative networking protocol called NetBEUI protocol.• Both TCP/IP and NetBEUI protocols can be used to share files and printers between wired and wirelesscomputers.3.5.2 Before TCP/IP Networking Configuration Setup3.5.2.1 What you should know before Configuration• TCP/IP protocol is a protocol used to connect to a Wide Area Network (WAN), such as the Internet orhard-wired Ethernet networks.• Every computer connecting to WAN has a unique number called IP address, which consists of two parts,network part and host part. For example, consider the IP address 150.205.30.9.Assuming this is part of a Class B network, the first two numbers (150.205) represent the network addressand the second two numbers (30.9) represent the host address. • Network administrator can divide the host part of IP address into two or more subnets for more effectiveuse. In that case, subnet mask is used to determine what kind of subnet the IP address belongs to.• You should consult your network administrator or Internet Service Provider (ISP) to find out your IPaddress and subnet mask.• There are two ways of obtaining an IP address. Some networks use Dynamic Host ConfigurationProtocol (DHCP) to dynamically assign an IP address every time you log on to the network. Others usestatic IP that is uniquely assigned to your computer and you use the same IP address whenever you log on tothe network.

24• You should consult your network administrator or Internet Service Provider (ISP) to find out if you woulduse DHCP or static IP.• Windows Internet Name Service (WINS) is a network service that resolves a computer NETBIOS nameto an IP address. It is similar in concept to the Domain Name Service (DNS) except WINS resolvesNETBIOS names while DNS resolves host names.• If you use a static IP and want to enable WINS, You should consult your network administrator or InternetService Provider (ISP) to find out the WINS server IP Address and Scope ID.• Gateway is a hardware or software set-up that translates between two dissimilar protocols. More easily, itcan also be called a specific point to access another system. So if you want to reach out to Internet from yourPC, you should set up a gateway to pass through.• You should consult your network administrator or Internet Service Provider (ISP) to find out yourGateway Address.• Domain Name Service (DNS) is the service that performs a mapping between domain names – moreEnglish-like names - and their corresponding IP address.• DNS can be either enabled or disabled. If you want to enable it, you should also consult your networkadministrator or Internet Service Provider (ISP) to find out your Host ID, Domain, DNS Server IPAddress, and Domain suffix.3.5.2.2 What you should have in your hands to proceed further• Whether you would use DHCP or static IP (Required)• Your Gateway Address (Required)• Your IP address and subnet mask. (If you want to use static IP)• WINS server IP Address and Scope ID (If you want to enable WINS using static IP)• Your Host ID, Domain, DNS Server IP Address, and Domain suffix (If you want to use DNS)(Consult your network administrator or ISP if you are not sure any of the above, and make sure you are readywith all the information necessary to proceed more.)

253.5.3 Setting Network Properties for “StructureNet” mode1. Do the step 1 and 2 mentioned in the previous section. (Section 3.4.2)2. In “Access Point Client Properties” box, check the StructureNet radio button in Operating Mode list.3. Enter the desired ESS ID for the Access Point you are authorized to use. (ESS ID is set to “magicwave” as default, but you can change it to another.)4. Change some options if you want.5. Click on “OK” to finish up the setup.6. Do the step 9 mentioned in the previous section (Section 3.4.2) to make the change effective.

263.5.4. Setting Network Properties for “Instawave” mode1. Do the step 1 and 2 mentioned in the section 3.4.2.2. In “Access Point Client Properties” box, check the Instawave radio button in Operating Mode list.3. Select the desired Channel you are authorized to use.4. Click on “OK” to finish up the setup.5. Do the step 9 mentioned in the section 3.4.2 to make the change effective.

273.5.5 TCP/IP Networking Configuration Setup3.5.5.1 TCP/IP Installation1. Right click on the Network Neighborhood icon and select “Properties” at the bottom “Network” box may appear as follows. If you find TCP/IP in the list of Configuration tab, skip to 3.5.5.2 (TCP/IP Properties Setup). To add TCP/IP, Click on “Add”.

282. When “Select Network Component Type” box appears, select “Protocol” since TCP/IP that we want to install is a Protocol. Click on “Add”. 3. "Select Network Protocol" box will appear. From the list of Manufacturers, select "Microsoft". From the list of Network Protocols list, select "TCP/IP". Click on "OK".

294. In “Network” box, you will see “TCP/IP”, which means that TCP/IP is successfully installedin your system now. 5. While TCP/IP is selected, click on “Properties” to proceed for TCP/IP Properties Setup.

303.5.5.2 TCP/IP Properties Setup1. Continuing from the last step, “TCP/IP Properties” box will appear. If not already selected,select IP Address tab on top of the box to display the IP configuration setting. If you find from yournetwork administrator or ISP that you would use DHCP so that you can get a dynamic IP every time youlog on the network, select “Obtain an IP address automatically” and proceed to step 2a. If you use astatic IP address, select “Specify an IP address” and type in your IP Address and Subnet Mask in theblank below, and proceed to step 2b.Go to WINS Configuration tab on top of the box to proceed.

312. WINS Configuration box will appear as follows.2a. If you use DHCP so that you would get a dynamic IP address every time you log on: Select “Use DHCP for WINS Resolution” at the bottom.2b. If you use a static IP address and want to:a. Disable WINS Resolution: Select “Disable WINS Resolution” in the middle.b. Enable WINS Resolution: Select “Enable WINS Resolution” and fill out the blanks for WINS Server Search Order and Scope ID using the information from your network administrator or ISP. Go to Gateway tab on top of the box to proceed.

323. Gateway box will appear on your screen as follows. If your network administrator or ISP provided you with a Gateway IP address, type that address into the “New Gateway” field and click on “Add”. If more than one IP addresses were provided to you, repeat the procedure until you type in all those numbers. Go to DNS Configuration tab of top of the box to proceed.

334. DNS Configuration box will appear as follows. If you want to disable DNS, check on the radio button for “Disable DNS”. Otherwise, check on the radio button for “Enable DNS” and type Host and Domain in the proper field. After that, type IP Address of DNS server in “DNS Server Search Order” box and click on “Add”. Repeat this procedures if multiple IP address of the DNS server were provided. If applicable, fill out the “Domain Suffix Search Order” field. Click on “OK” at the bottom of “TCP/IP Properties” box. 5. “System Setting Change” box will appear as follows. Click on “Yes” to restart your computer so that the whole installation procedures take effects.

344. MagicLAN Installation for Windows NT4.1 Hardware InstallationHardware installation procedure for Windows NT is exactly same as the one for Windows 95/98.Please make a reference of the Windows 95/98 hardware installation section. (Section 3.1)4.2 Software Installation4.2.1 When there is no Windows NT Networking installed yet1. Unlike Windows 95/98, since Windows NT does not support Plug and Play (PnP), you should add your driver manually. To do so, click on “start” in task bar, go to “Settings”, and go to “Control Panel”.2. Under “Control Panel”, double click on Network icon.3. Since there is no NT networking installed in your system, you may be asked if you want to install NTnetworking first. Click on “Yes” button. Next, you may be asked to specify how you access to the network:modem or LAN. Check the proper selection and click on “Next”. In “Network Setup Wizard” box, clickon “Select from list” button. 4. In “Select Network Adapter” box, click on “Have Disk” button.

$35 5. In “Insert Disk” box, you may be asked to specify the necessary software directory. Insert the MagicLANinstallation disk into the floppy disk drive, type in “A:\nt4.0” in the blank and click on “OK” button. (Inthis example, we assume we are installing Windows NT version 4.0.) 6. In “Select OEM Option” box, two adapters found may appear in the list. Select the proper adapter andclick on “OK” button. Usually you can select PCMCIA for laptop. In the next box, make sure thatSAMSUNG Wireless LAN Card is checked and click on “Next”. 7. In the next box to choose protocols to use, make sure that all the protocols you want to use are checkedand click on “Next”.$

36 8. In the next box to choose network services to use, make sure that all the services you want to use arechecked and click on “Next”. 9. In the next box, it is confirmed that necessary NT networking components are selected. Click on “Next”.

$37 10. When you are asked to specify the directory that the necessary NT files are copied from, insertyour Windows NT CD and type in “e:\i386” in the location blank. (Here it is assumed that the CD-ROMdrive is e drive) 11. Some files from the “e:\i386” directory are copied and you may be prompted the same box to askyou to specify where the NT files are once more. Since it is looking for some files from the installationdiskette this time, insert your installation disk into floppy disk drive and type in “a:\nt4.0” in the locationblank. Windows NT networking is successfully installed now 12. “Configure Wireless LAN Card” box may appear as follows. Set each some parameters (I/O$

38Base,Interrupt, Fragmentation Threshold, RTS Threshold) for the proper system configuration setup and otherparameters (Operating Mode, ESS ID, etc.) for the proper LAN Card configuration setup. For theinformation on LAN Card-related parameters, you can refer to the explanation on the previous section(3.4 SAMSUNG Wireless LAN Card Properties Setup). If you are not sure any of system configuration-related parameters, please refer to your network administrator. After you set all the parameters necessary,click on “OK” to proceed. 13. Network binding related box may appear next. Click on “Next” to proceed. 14. Next box will say network installation is done and network is ready to start. Click on “Next” inthat box and “Finish” on the next box to start network.

39 15. You will be prompted to enter the name of the Workgroup or Domain in the next box. Type in adesired name of it and click on “Next” to proceed. 16. “Network” box with Identification tab selected will appear as follows. You can change theComputer Name and Workgroup after clicking on “Change” in the middle of the box.

40 17. Go to Adapters tab of the “Network” box, and make sure that “SAMSUNG Wireless LANCard” are installed and currently selected. 18. Go to Binding tab of the “Network” box and check if all the necessary services are binded.

41 19. Go to Protocols tab of the “Network” box. Select “TCP/IP Protocol” in the list and click on“Properties” button. 20. “Microsoft TCP/IP Properties” box with IP Address tab selected will appear as follows. Select“SAMSUNG Wireless LAN Card” in the Adapter section, and fill out the rest sections with properinformation. About the parameters and meaning, you can refer to the explanation in the previous section.

42(3.5 Network Configuration Setup). If you are not sure about any of the required information in thissection, please consult to your network administrator. Go to DNS tab. 21. In “Microsoft TCP/IP Properties” box with DNS tab selected, enter the proper information forthe blanks. About the parameters and meaning, you can refer to the explanation in the previous section.(3.5 Network Configuration Setup). If you are not sure about any of the required information in thissection,please consult to your network administrator. Go to WINS Address tab.

43 22. In “Microsoft TCP/IP Properties” box with WINS Address tab selected, select SAMSUNGWireless LAN Card (PCMCIA) and fill the rest of the blanks with the proper information. About theparameters and meaning, you can refer to the explanation in the previous section. (3.5 NetworkConfiguration Setup). If you are not sure about any of the required information in this section, pleaseconsult to your network administrator. Go to Routing tab.

4423. In “Microsoft TCP/IP Properties” box with Routing tab selected, make sure if “Use IPRouting” is checked only if you want NT to play a role of router in your network. Click on “OK”. 24. When TCP/IP properties are set, click on “Close”. Then “System Setting Change” box willappear as follows. Click on “Yes” to restart your computer so that the whole installation procedures takeeffects. 4.2.2 When There is Windows NT networking already installed1. Unlike Windows 95/98, since Windows NT does not support Plug and Play (PnP), you should add your driver manually. To do so, click on “start” in task bar, go to “Settings”, and go to “Control Panel”.2. Under “Control Panel”, double click on Network icon.

453. “Network” box with Identification tab selected may appear as follows. You can change the ComputerName and Workgroup after clicking on “Change” in the middle of the box. 4. Go to Adapters tab of the “Network” box, and click on “Add” button in the middle.

$465. “Select Network Adapter” box may appear as follows. Click on “Have Disk”. 6. “Insert Disk” box may appear as follows. Insert the Installation Diskette into your floppy drive andspecify the path “A:\nt4.0” in blank field. Click on “OK”. (In this example, we assume we are installingWindows NT version 4.0.) 7. If the Driver is successfully set up, “Select OEM Option” box may appear. Select the card type. Usuallyyou can select PCMCIA for laptop. Click on “OK”. 8. “Configure Wireless LAN Card” box may appear as follows. Set each some parameters (I/O Base,$

47Interrupt, Fragmentation Threshold, RTS Threshold) for the proper system configuration setup and otherparameters (Operating Mode, ESS ID, etc.) for the proper LAN Card configuration setup. For theinformation on LAN Card-related parameters, you can refer to the explanation on the previous section(3.4 SAMSUNG Wireless LAN Card Properties Setup). If you are not sure any of system configuration-related parameters, please refer to your network administrator. After you set all the parameters necessary,click on “OK” to proceed. 9. “Network” box with Adapters tab selected may appear as follows. Make sure “SAMSUNG WirelessLAN Card” is installed and currently selected.

4810. Go to Binding tab of the “Network” box. Make sure that all the necessary services are binded. 11. Go to Protocols tab in the “Network” box. If you have TCP/IP protocol already installed in yoursystem, select “TCP/IP Protocol” and click on “Properties”. If you do not have TCP/IP protocol installedyet, you will have to add it by clicking on “Add” button, selecting “TCP/IP Protocol”, and clicking on“OK”. Once you add it, click on “Properties”.

49 12. “Microsoft TCP/IP Properties” box with IP Address tab selected will appear as follows. Select“SAMSUNG Wireless LAN Card” in the Adapters section, and fill out the rest sections with properinformation. About the parameters and meaning, you can refer to the explanation in the previous section.(3.5 Network Configuration Setup). If you are not sure about any of the required information in thissection, please consult to your network administrator. Go to DNS tab.

5013. In “Microsoft TCP/IP Properties” box with DNS tab selected, enter the proper information forthe blanks. About the parameters and meaning, you can refer to the explanation in the previous section.(3.5 Network Configuration Setup). If you are not sure about any of the required information in thissection,please consult to your network administrator. Go to WINS Address tab. 14. In “Microsoft TCP/IP Properties” box with WINS Address tab selected, select “SAMSUNGWireless LAN Card” and fill the rest of the blanks with the proper information. About the parametersand meaning, you can refer to the explanation in the previous section. (3.5 Network Configuration Setup).If you are not sure about any of the required information in this section, please consult to your networkadministrator. Go to Routing tab.

51 15. In “Microsoft TCP/IP Properties” box with Routing tab selected, make sure that “Enable IPForwarding” is checked only if you want NT to play a role of router in your network. Click on “OK”. 16. When TCP/IP properties are set, click on “Close”. Then “System Setting Change” box willappear as follows. Click on “Yes” to restart your computer so that the whole installation procedures take

$535. Packet Driver Installation for MS-DOS5.1 Copy the Packet Driver1. Create a new directory where you want to store a Packet Driver software on your hard disk.Ex> c:\>md packet(From this point, directory “Packet” right under root directory will be used for packet driversoftware directory for clearer explanation.)2. Insert the installation diskette in drive A.3. Copy all files in 'a:\dos>' to the ‘c:\Packet>’ directory which you created in the step 1. Ex> a:\dos>copy *.* c:\packet5.2 Setup AUTOEXEC.BAT1. Change current directory to c:\2. Open 'AUTOEXEC.BAT' with any text editor such as edit.exe Ex> c:\>edit autoexec.bat3. Add the following line at the last line of ‘AUTOEXEC.BAT’ file. Ex> c:\packet\magicwav.exe4. Save 'AUTOEXEC.BAT' and exit the editor program.5.3 Setup MAGICWAV.CFG1. Change current directory to “Packet” directory right under root(C:\) directory.2. Open 'MAGICWAV.CFG' using a text editor such as edit.exe. Ex> edit MagicWave.cfg3. The structure of the 'MAGICWAV.CFG' is as follows. a. Basic Parameters that should be set: ESSID: MAGICWAVE (default) NETWORKMODE: 1 (default) CHANNEL: 3 (default) INTEROP: 1 (default) b. Parameters for Users that the driver will ignore: (If you do not want to use PNP, set these parameters.) IRQ: 9 (default) IO: 240 (default) MEM: D800 (default)$

Samsung Electro Mechanics SWL-2000N PCMCIA Card User Manual Manual

Samsung Electro Mechanics PCMCIA Card Manual

Contents

manual

Navigation menu

Namespaces

Views

Navigation