Samsung Electronics Co HLM617W DLP Projection TV User Manual BP68 00120A cover

Download:
Mirror Download [FCC.gov]
Document ID	373460
Application ID	5T6Db+Vutkx/dKTORhENyw==
Document Description	Users Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	236.25kB (2953112 bits)
Date Submitted	2003-11-13 00:00:00
Date Available	2003-11-13 00:00:00
Creation Date	2003-11-13 15:23:18
Producing Software	Acrobat Distiller 5.0.5 for Macintosh
Document Lastmod	2003-11-13 15:23:29
Document Title	BP68-00120A-cover
Document Creator	QuarkXPress.: AdobePS 8.5.1
Document Author:	jung

BP68-00120A-3
3/27/03
8:25 AM
Page 32
Operation
Channel Memory
Storing Channels in Memory Automatically
Your TV can memorize and store all of the channels available. Once the channels are memorized,
you can use the CH
and CH buttons to scan through the available channels.
First, select the broadcast source as
described on the previous page. With
the Channel Setup menu on screen,
move the joystick down to select “Auto
Channel Memory.”
Press the joystick to enter. The TV will
begin memorizing all of the available
stations. Press the VOL+ button at any
time to interrupt the memorization
process.
Selecting the Broadcast Source
Before memorizing available channels, you must select what broadcast source your TV is connected to, either an antenna or a cable system.
Press the Menu button.
Move the joystick down to
select SETUP, then press the
joystick to enter.
Press the joystick to enter. The
channel setup menu will
appear. Move the joystick
down to select “Air or CATV”.
NOTE
• When the ANT B mode is selected, the auto programming runs on the main screen.
Adding and Erasing Channels
32
If you are connected to an
antenna, leave “AIR” displayed. If you connected
cable, press the joystick to the
right to display the type of
cable system: “STD,” “HRC,”
or “IRC.”
(If you are not sure which type
of cable system you have,
contact your cable company.)
Use the number buttons to select the
channel you want to add or erase.
To add a channel, select it and press the
Add/Erase button on the remote control.
The channel will be added to the TV’s
memory and the word “Channel added”
will appear in the corner of the screen.
To erase a channel, select it and then
press the Add/Erase button on the
remote control. The word “Channel
erased” will appear in the corner of the
screen. You can still view a channel that
has been erased from memory by using
the number buttons on the remote control
to select the channel directly.
33
BP68-00120A-3
3/27/03
8:25 AM
Page 34
Operation
Changing Channels
Selecting Your Favorite Channels
You can change channels on your TV by using the CH
and CH
buttons, or by direct selection using the number buttons. You can use the number buttons to tune to any channel (even one
that has been erased or has not been memorized).
You can store up to ten of your favorite channels for each available input source (such as TV and
CATV). Then, when you press the Fav.CH button on the remote control, the TV displays only the
favorite channels you previously stored, allowing you to quickly and easily find frequently
watched channels.
Using the Channel Buttons
To Store Your Favorite Channels:
Press the CH or CH
buttons to change channels.
The TV changes each channel in order, up or down,
depending on which button you press. You will see all
the channels that the TV has memorized. (The TV must
have memorized at least three channels.) You will not
see channels that were not memorized or have been
erased.
Press the Menu button. Move
the joystick down to select
SETUP, then press the joystick
to enter.
Press the joystick to enter.
The channel setup menu will
appear. Move the joystick
down to select Air or CATV,
then move the joystick to
the right to display the type of
cable system or Air.
Move the joystick down to
select “Favorite Channel”,
then press the joystick to
enter.
Move the joystick to the left
or right to select channel.
Note: Only memorized channels can be set as Favorite
channels.
Using the Number Buttons
To change to single-digit channels (0–9) faster, press
“0” before the single digit.
Example: For channel 4, press “0,” then “4.”
To select a channel over 100, press the +100 button
first.
Example: For channel 122, press “+100,” then “2,” then “2.”
Using the Previous Channel
Press the Pre-ch button on the remote control. The TV
changes to the last channel you were watching.
Scanning channels
You can automatically scan all of the channels in memory at the touch of just one button. Press the Scan button
on the remote control. The TV will change the channels
automatically, one by one. Scanning channels will be
displayed in the PIP window. To stop channel scan,
press the Scan button again.
NOTE
• When the ANT B mode is selected, the channel scan function
doesn’t work.
34
To View Your Favorite Channels:
Press the Fav.CH button repeatedly to
jump from one favorite channel
to another.
The favorite channels are selected in
ascending sequence.
35
BP68-00120A-3
3/27/03
8:25 AM
Page 36
Operation
Labeling the Channels
Setting The On/Off Melody
Use this feature to assign an easy-to-remember label to any channel (i.e., “CBS”, “ESPN”,
“PBS2”, CNN1”, etc.) A label consists of four fields, where each field is a letter, a number, or a
blank. When the DISPLAY button is pressed, the channel label will appear next to the channel
number.
You can hear clear melody sound when the TV is powered On or Off.
Press the Menu button. Move
the joystick down to select
SETUP, then press the joystick
to enter.
Move the joystick down to
select Melody.
Move the joystick to the right
or left to select “On”.
Press the Menu button to exit.
Press the CH or CH
button to tune to the channel that
will be labeled.
Press the Menu button. Move
the joystick down to select
SETUP, then press the joystick
to enter.
Press the joystick to enter.
Move the joystick down to
select Labeling.
Move
36
Move the joystick to the right
to begin labeling. (Each label
has four fields. See top paragraph.)
Move the joystick up or down
to select a letter, a number, or
a blank. (Pressing the CH button results in this sequence:
A,B,...Z, blank,0,1,...9).
Move the joystick to the right
to switch to the next field,
which will be selected. Select
a second letter or digit using
joystick(up or down), as
above. Repeat the process to
select the last two digits.
Press the Menu button to exit.
Select
Menu
37
BP68-00120A-3
3/27/03
8:25 AM
Page 38
Operation
Picture Control
Using Automatic (“Standard”) Picture Settings
Using the remote, you can change the contrast, brightness, tint, color, and sharpness settings of
the TV.
Press the P.Mode button on the remote
control to change the picture settings.
Press P.Mode repeatedly to select the
“Dynamic”, “Standard”, “Movie” or
“Custom” picture setting.
Customizing the Picture
Press the Menu button.
Press the joystick to enter.
Move the joystick down to
select Adjust, then press the
joystick to enter. You will see
the items “Contrast”,
“Brightness”, “Sharpness”,
“Color” and “Tint”.
Move the joystick up or down
to select the item you want to
change.
Move the joystick right or left
to raise or lower the value of
the item, using the on-screen
gauge as your guide.
Guide to Automatic Picture Settings
• Choose Standard to set the TV to operate at top performance according to your TV’s
specifications.
• Choose Dynamic for viewing the TV during the day or when there is bright light in the room.
• Choose Movie when viewing the movie.
• Choose Custom if you want to adjust the settings yourself.
When you are finished adjusting an item, wait a moment. The
level indicator will disappear and the Video menu will return.
You can continue to make adjustments, or press the Menu button to
exit.
38
39
BP68-00120A-3
3/27/03
8:25 AM
Page 40
Operation
Sound Control
You can control and customize the sound levels and settings of the TV with the remote control.
Using the on-screen menus, you can change the TV’s bass, treble, and balance settings.
Adjusting the Volume
Move the joystick up or down to select
the item you want to change.
Move the joystick right or left to raise or
lower the value of the item, using the onscreen gauge as your guide.
Press VOL + to raise the volume or
VOL – to lower the volume.
You can continue to make adjustments, or press the Menu button to exit.
Using the Mute Button
Press the Mute button on the remote
control to silence the volume. The word
“Mute” will appear in the lower left corner of the screen.
Using Automatic(Standard) Sound Settings
To turn mute off, press the Mute button
again, or raise or lower the volume
with the VOL – and VOL + buttons.
Press the S.Mode button on the remote
control to change the automatic sound
setting.
Customizing the Sound
Press the S.Mode button again to select
the “Standard”, “Music”, “Movie”,
“Speech” or “Custom” sound setting.
Press the Menu button.
Move the joystick down to
select SOUND, then press the
joystick to enter.
Guide to Automatic Sound Settings
Move the joystick down to
select Adjust, then press the
joystick to enter. You will see
the items “Bass”, “Treble” or
“Balance”.
•
•
•
•
•
Choose
Choose
Choose
Choose
Choose
Standard for the “factory” settings (the best choice for most people).
Music when watching music videos or concerts.
Movie when watching a movie.
Speech when watching a show that is mostly dialogue, like a news show.
Custom if you want to adjust the settings yourself.
Continued...
40
41
BP68-00120A-3
3/27/03
8:25 AM
Page 42
Operation
Setting the Clock
Setting the Timers
This TV has a built-in clock that will appear on screen when you press the Display button on the
remote control. Setting this clock also allows you to use it to automatically turn the TV on or off.
This TV can be set to turn on or off automatically at specific times that you choose. Before using
the timers, you must set the TV’s clock, as described previously.
Setting the On/Off Timer
42
Press the Menu button.
Move the joystick down to
select SETUP, then press the
joystick to enter.
Press the Menu button. Move the joystick
down to select SETUP, then press the
joystick to enter.
Move the joystick down to
select Time, then press the
joystick to enter.
Move the joystick down to select Time,
then press the joystick to enter.
Move the joystick right to
select the hour. Move the joystick up or down to select the
correct hour.
Move the joystick down to select the
“On Time”. Move the joystick right to
select the hour, then Move the joystick
up or down to adjust the hour for the TV
to turn on. When selecting the hours, be
sure to select the proper time of day (am
or pm).
Move the joystick right to
select the minute. Move the
joystick up or down to select
the correct minute.
When selecting the hours, be
sure to select the proper time
of day (am or pm).
Move the joystick right to select the
minute. Move the joystick up or down to
adjust the minute.
Press Menu to exit the menus.
Continued...
43
BP68-00120A-3
3/27/03
8:25 AM
Page 44
Operation
Move the joystick right to select off, then
move the joystick up or down to select
“on”.
When any of the timers are set, the
“Timer” LED will illuminate (front or side
panel of TV.).
When you are finished, move the joystick right.
If you want to set the Off time, move the
joystick down to select the “Off Time”.
Set the “Off Time” just as you set the
“On Time”.
If you want to set the volume level or
channel when the TV turns on, move the
joystick down to select “On Timer Vol.”
or “On Timer CH”. Move the joystick
right to set the volume level or to select
the channel you want when the TV turns
on. Press the Menu button to return to
normal viewing.
Setting the Sleep Timer
You can set your TV to automatically turn off after a preset interval.
44
Press the Sleep button on the remote control.
You’ll see “Off” at the bottom of the
screen. Press the Sleep button to select
the time interval for the TV to stay on.
The interval ranges from 10 to 360 minutes.
Viewing an External Signal Source
Selecting the Signal Source
Use the remote control to switch between viewing signals from connected equipment, such as
VCRs, DVD, Set-Top box and the TV source (broadcast or cable).
Make sure that the remote
control is controlling the TV
set. Press the MODE button
and make sure that the “TV”
LED is illuminated.
Press TV/VIDEO on the
remote control, and the following on-screen menu will
appear.
Move the joystick up or down
to select a particular signal
source, and then press the
joystick to activate it.
When you connect equipment to the TV, you can choose
between the following sets of jacks: Video 1, Video 2, S-video 1,
S-video 2, Component 1, Component 2, Component 3, DVI or
PC on the TV’s rear panel, and Video 3 or S-Video 3 on the TV’s
side panel.
Remote Control VCR/DVD Buttons
Flip the cover of the remote control up to access buttons that can
control the tape functions of a connected VCR or DVD, including
Rewind, Play, Fast Forward, Stop and Pause.
Flip the cover of your remote control unit for access to the tape function controls. Press the appropriate
buttons to control your VCR or
DVD.
45
BP68-00120A-4
3/27/03
8:28 AM
Page 46
SAMSUNG
Special Features
BP68-00120A-4
3/27/03
8:28 AM
Page 48
Special Features
Setting Up Your Remote Control
Setting Up the Remote to Operate Your Cable Box
This TV’s remote control can operate almost any VCR, cable box, or DVD. After it has been set up
properly, your remote control can operate in four different modes: TV, VCR, Cable, or DVD.
Pressing the corresponding button on the remote control allows you to switch between these modes,
and control whichever piece of equipment you choose.
Turn off your cable box.
Note
Press the MODE button and make sure
that the Cable LED is illuminated.
Press the SET button on your TV’s remote
control.
Using the number buttons on your remote
control, enter three digits of the cable
box code listed on page 51 of this manual for your brand of cable box. Make
sure you enter three digits of the code,
even if the first digit is a “0.” If there is
more than one code listed, try the first
one.
Press the Power button on the remote
control. Your cable box should turn on if
your remote is set up correctly.
The remote control might not be compatible with all DVD Players, VCRs and Cable boxes.
Setting Up the Remote to Operate Your VCR
Turn off your VCR.
Press the MODE button and make sure
that the VCR LED is illuminated.
Press the Set button on your TV’s remote
control.
Using the number buttons on your remote
control, enter three digits of the VCR
code listed on page 51 of this manual
for your brand of VCR. Make sure you
enter three digits of the code, even if the
first digit is a “0”. (If more than one code
is listed, try the first one.)
Press the Power button on the remote
control. Your VCR should turn on if your
remote is set up correctly.
If your cable box does not turn on after
set up, repeat steps 2, 3, and 4, but try
one of the other codes listed for your
brand of cable box. If no other codes
are listed, try each code, 000 through
077.
If your VCR does not turn on after set up,
repeat steps 2, 3, and 4, but try one of
the other codes listed for your brand of
VCR. If no other codes are listed, try
each VCR code, 000 through 089.
Note on Using Remote Control Modes: Cable Box
Note on Using Remote Control Modes: VCR
• When your remote control is in “VCR” mode, the volume buttons still control your TV’s volume.
48
• When your remote control is in “Cable Box” mode, the volume buttons still control your TV’s volume.
49
BP68-00120A-4
3/27/03
8:28 AM
Page 50
Special Features
Setting Up the Remote to Operate Your DVD
Turn off your DVD.
Press the MODE button and make sure
that the DVD LED is illuminated.
Press the SET button on your TV’s remote
control.
Using the number buttons on your
remote control, enter three digits of the
DVD code listed on page 51 of this
manual for your brand of DVD. Make
sure you enter three digits of the code,
even if the first digit is a “0.” If there is
more than one code listed, try the first
one.
Press the Power button on the remote
control. Your DVD should turn on if your
remote is set up correctly.
Remote Control Codes
VCR Codes
If your DVD does not turn on after set
up, repeat steps 2, 3, and 4, but try
one of the other codes listed for your
brand of DVD. If no other codes are listed, try each code, 000 through 008.
Cable Box Codes
DVD Codes
Note on Using Remote Control Modes: DVD
• When your remote control is in “DVD” mode, the volume buttons still control your TV’s volume.
50
51
BP68-00120A-4
3/27/03
8:28 AM
Page 52
Special Features
Fine Tuning Channels
Selecting the Color Tone
Fine tuning lets you manually adjust the TV’s tuner if you have difficulty tuning in a channel.
Using the number buttons on
the remote control, select the
channel you want to fine tune.
Press the Menu button on the
remote control. Move the joystick down to select SETUP,
then press the joystick to
enter.
Press the joystick to enter in
the Channel setup menu.
Press the Menu button.
Press the joystick to enter.
Move the joystick down to
select Color Tone, then
move the joystick right
repeatedly to select
“Normal”, “Warm1”,
“Warm2”, “Cool2” or
“Cool1”.
Press the Menu button to exit.
Setting the Film Mode
On: Automatically senses and processes film signals from all
sources and adjusts the picture for optimum quality.
Off: Switches off the Film mode.
Move the joystick down to
select the Fine tune, then
move the joystick right or left
to adjust the fine tuning.
To store the fine tuning setting
in the TV’s memory, move the
joystick up. (A heart icon will
appear.)
To reset the fine tuning to “0,”
move the joystick down .
52
Press the Menu button.
Press the joystick to enter.
Move the joystick down to
select Film Mode, then
move the joystick to the right
or left to select “On” or
“Off”.
Press the Menu button to exit.
Note: Film mode is supported in
480i only.
Press the Menu button to exit.
53
BP68-00120A-4
3/27/03
8:28 AM
Page 54
Special Features
DNIeTM (Digital Natural Image engine)
Digital Noise Reduction
Samsung’s New Technology enables an improved image with detail, contrast and white enhancement and 3D noise reduction.
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction
feature to help reduce any static and ghosting that may appear on the screen.
Press the Menu button.
Press the joystick to enter.
Move the joystick down to
select DNIe, then move the
joystick to the right or left to
select “On”, “Demo” or “Off”.
Quick way to access DNIe:
Just press the “DNIe” button
on the remote control to select
“DNIe On” or “DNIe Demo”.
Press the Menu button.
Press the joystick to enter.
Move the joystick down to
select Digital NR, then
move the joystick to the right
or left to select “On” or
“Off”.
Press the Menu button to
exit.
Press the Menu button to exit.
Guide to DNIe Settings
• On: Switches on the DNIe mode.
• Demo: The screen before applying DNIe appears on the right
and the screen after applying DNIe appears on the left.
DNIe Demo
DNIe On
DNIe Off
• Off: Switches off the DNIe mode.
NOTE
• The DNIe function doesn’t operate in the PC and DVI modes.
54
55
BP68-00120A-4
3/27/03
8:28 AM
Page 56
Special Features
Setting the Blue Screen Mode
Changing the Screen Size
If no signal is being received or the signal is very weak, a blue screen automatically
replaces the noisy picture background. If you wish to continue viewing the poor picture,
you must set the “Blue screen” mode to “Off”.
When you press the ASPECT button on the remote control, the TV’s screen mode choices appear
in sequence. The screen displays in this order: Wide, Panorama, Zoom1, Zoom2, Normal.
The name of the screen mode will be displayed at the bottom of the TV screen.
Wide
Press the Menu button on the
remote control. Move the joystick down to select SETUP,
then press the joystick to
enter.
Sets the picture to 16:9 wide mode.
Move the joystick down to
select Blue Screen.
Use this mode for the wide aspect ratio of
a panoramic picture.
Move the joystick to the right
or left to select “On” or “Off”.
Press the Menu button to exit.
Panorama
Zoom1
Magnifies the size of the picture on
screen.
You can also move the picture on screen
using the “Scroll” function. Press the CH
( , ) buttons to scroll the picture.
Zoom2
Magnifies the size of the picture more
than Zoom1.
You can also move the picture on screen
using the “Scroll” function. Press the CH
( , ) buttons to scroll the picture.
Normal
Sets the picture to 4:3 normal mode.
This is a standard TV screen size.
continued...
56
57

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2003:11:13 15:23:29-05:00
Create Date                     : 2003:11:13 15:23:18-05:00
Title                           : BP68-00120A-cover
Author                          : jung
Creator                         : QuarkXPress.: AdobePS 8.5.1
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Page Count                      : 13
Mod Date                        : 2003:11:13 15:23:29-05:00
Creation Date                   : 2003:11:13 15:23:18-05:00
Metadata Date                   : 2003:11:13 15:23:29-05:00

EXIF Metadata provided by EXIF.tools