Samsung Electronics Co HPP4261 PDP TV Monitor User Manual BN68 00678A 00 cover
Samsung Electronics Co Ltd PDP TV Monitor BN68 00678A 00 cover
Contents
- 1. Users Manual 1
- 2. Users Manual 2
- 3. Users Manual 3
Users Manual 2
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 416756 |
| Application ID | Lef7+HzC+7FvoEV2up8kbg== |
| Document Description | Users Manual 2 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 258.89kB (3236079 bits) |
| Date Submitted | 2004-04-22 00:00:00 |
| Date Available | 2004-04-22 00:00:00 |
| Creation Date | 2004-03-14 16:44:50 |
| Producing Software | Acrobat Distiller 5.0.5 for Macintosh |
| Document Lastmod | 2004-04-22 11:04:36 |
| Document Title | BN68-00678A-00_cover |
| Document Creator | QuarkXPress.. 4.1E: AdobePS 8.7.3 (301) |
| Document Author: | 1004 |
Setting Up Your Remote Control This PDP's remote control can operate almost any VCR, cable box or DVD. After it has been set up properly, your remote control can operate in four different modes :TV , VCR, Cable, DVD or STB. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose. Note : ● ● The remote control may not be compatible with all DVD Players, VCRs, Cable boxes. The remote control can only operate STB made by Samsung. Setting Up the Remote to Operate Your VCR, Cable box or DVD player Turn off your VCR. (or Cable box, DVD player) Press the MODE button. Mode is changed whenever MODE button is pressed. Press the SET button on your TV's remote control. Using the number buttons on your remote control, enter three digits of the VCR (or Cable box, DVD player) code listed on page 35 of this manual for your brand of VCR (or CATV, DVD). Make sure you enter three digits of the code, even if the first digit is a "0". (If more than one code is listed, try the first one.) Press the POWER button on the remote control. Your VCR (or CATV, DVD) should turn on if your remote is set up correctly. If your VCR (or CATV, DVD) does not turn on after setup, repeat steps 2, 3, and 4, but try one of the other codes listed for your brand of VCR (or CATV, DVD). If no other codes are listed, try each code, 000 through 089 (or Cable box: 000 through 077, DVD player: 000 through 008). Notes • When your remote control is in “VCR” mode, the VCR control buttons (STOP, REW, PLAY/PAUSE, FF) still operate your VCR. • When your remote control is in “CATV” or “DVD” mode, the VCR control buttons (STOP, REW, PLAY/PAUSE, FF) still operate your VCR. • You do not need to program the remote for Samsung STBs as the codes are pre-programmed. 34 Remote Control Codes VCR Codes Cable Box Codes DVD Codes 35 Viewing an External Signal Source Use the remote control to switch between viewing signals from connected equipment, such as VCRs, DVD, Set-Top box and the TV source (broadcast or cable). Setting the Signal Source Press the MENU button. Press the ENTER button to select “Input”. Input TV Source List Edit Name Move Press the ENTER button to select “Source List”. Move √ √ Enter Return Source List TV TV AV1 AV2 AV3 S-Video1 S-Video2 Component1 †More Press the ▲ or ▼ button to select signal source, then press the ENTER button. : TV ------------------Enter Source List TV TV AV1 AV2 AV3 S-Video1 S-Video2 Component1 †More Move VCR ---------------Enter Notes • When you connect equipment to the PDP, you can choose between the following sets of jacks: AV1, AV2, AV3, S-Video1, S-Video2, Component1, Component2, PC or DVI on the PDP’s rear panel. 36 Return Return Assigning Names to External input mode Press the MENU button. Press the ENTER button to select “Input”. Input TV Source List Edit Name : TV √ √ Edit Name Move Press the ▲ or ▼ button to select “Edit Name”, then press the ENTER button. AV1 AV2 AV3 S-Video1 S-Video2 Component1 Component2 †More ---------------------- √ √ √ √ √ √ √ Edit Name Enter Return Edit Name TV AV1 AV2 AV3 S-Video1 S-Video2 Component1 Component2 †More Move Return Edit Name TV Move Press the ENTER button. • Press the ▲ or ▼ button to select external device: VCR, DVD, Cable STB, HD STB, Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DHR or PC. Set other signal sources (AV2, AV3, S-Video1, S-Video2, Component1, Component2, PC or DVI) using the same method as listed above. Enter ---- ---- √ - - - - VCR √ ---√ DVD ---√ STB √ - - - Cable - - - -HD STB √ STB √ - - -Satellite † Enter Return Press the MENU button to exit. Notes • DHR : DVD HDD Recorder 37 P Picture Control Customizing the Picture ................................................................40 Using Automatic Picture Settings ....................................................41 Selecting the Color Tone................................................................42 DNIe (Digital Natural Image engine) ............................................43 Changing the Screen Size ............................................................44 Freezing the Picture ......................................................................46 Viewing the Picture-in-Picture..........................................................47 Selecting a Signal Source (Antenna or Cable) for PIP ........................52 Setting the MCC(My Control Color) Mode ......................................54 Customizing the Picture You can use the on-screen menus to change the Contrast, Brightness, Sharpness, Color, and Tint settings of your PDP. Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the ▲ or ▼ button to select “Custom”, then press the ENTER button. You will also see the items “Contrast”, “Brightness”, “Sharpness”, “Color” and “Tint”. Press the ▲ or ▼ button to select the item you wish to change, then press the ENTER button. Press the œ or √ button to change the value of the item. Press the MENU button to exit. Note • In the PC/DVI mode, you can’t adjust the Color and Tint. 40 : Normal : Off : 16:9 Enter Contrast Brightness Sharpness Color Tint G 50 Contrast √ √ √ √ √ √ √ Return Custom TV Move : Custom 60 35 50 55 R 50 Enter Return 74 Using Automatic Picture Settings Your PDP has automatic picture settings that allow you to adjust the video display easily. Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More ➤ Quick way to access the picture setting: Just press the “P.MODE” button on the remote control. Move Press the ENTER button to select “Mode”. Move : Normal : Off : 16:9 Enter Return Dynamic : Custom Standard : Normal Movie Custom : Off : 16:9 Enter Return Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move √ √ √ √ √ √ √ Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Press the ▲ or ▼ button to select “Dynamic”, “Standard”, “Movie”, “Custom” picture setting. • You can select “Custom”, “Entertain”, “Internet”, or “Text” in PC/DVI mode. : Custom Dynamic : Custom Standard : Normal Movie Custom : Off : 16:9 Enter Return Press the MENU button to exit. 41 Selecting the Color Tone Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the ▲ or ▼ button to select “Color Tone”, then press the ENTER button. Mode Custom Color Tone Color Control Film Mode Size PIP † More 42 : Off : 16:9 Enter Return : Custom : Normal Cool2 Cool1 : Off Normal : 16:9 Warm1 Warm2 Enter Return Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the MENU button to exit. : Normal √ √ √ √ √ √ √ Picture TV Move Press the ▲ or ▼ button to select “Cool2”, “Cool1”, “Normal”, “Warm1” or “Warm2”. • You can select “Custom”, “Cool”, Normal” or “Warm” in PC mode. • You can select “Cool”, “Normal” or “Warm” in DVI mode. : Custom : Custom : Normal Cool2 Cool1 : Off Normal : 16:9 Warm1 Warm2 Enter Return DNIe (Digital Natural Image engine) Samsung’s New Technology brings you more detailed images with contrast, white enhancement and 3D noise reduction. Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More ➤ Quick way to select DNIe: Simply press the “DNIe” button under the cover of the remote control. Move Press the ▲ or ▼ button to select “DNIe”, then press the ENTER button. • On : Switches on the DNIe mode. • Off : Switches off the DNIe mode. • Demo : The screen before applying DNIe appears on the right and the screen after applying DNIe appears on the left. … More DNIe MCC : Off : 16:9 Enter Return : On On Off Demo Enter Return Picture TV … More DNIe MCC Move : Normal √ √ √ √ √ √ √ Picture TV Move Press the ▲ or ▼ button to select “On”, “Off” or “Demo”. : Custom : On On Off Demo Enter Return Press the MENU button to exit. 43 Changing the Screen Size Screen size selection depends on the type of video input(DVD, PC etc.). ➤ Quick way to access the Screen Size menu : Just press the “ASPECT” button on the remote control. Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the ▲ or ▼ button to select “Size”, then press the ENTER button. Mode Custom Color Tone Color Control Film Mode Size PIP † More : Normal : Off : 16:9 Enter Return : Custom √ √ √ √ √ √ √ : Normal : Off : 16:9 Enter Return Size TV 16 : 9 Panorama Zoom 4:3 Move √ √ √ √ √ √ √ Picture TV Move Press the ▲ or ▼ button to select the screen size you want. : Custom Enter Return Press the MENU button to exit. Note • If you watch a still image or the 4:3 (Normal) mode for a long time (over 2 hours), an image may be burned onto the screen. View the monitor in 16:9(Wide) or Panorama mode as much as possible. 44 16:9(W ide) 16:9 Aspect Ratio that fits DVD and Wide Screen applications. 16:9 Panorama Fits a 16:9 picture onto a 4:3 screen and displays it without clipping the image. Panorama Zoom Magnifies the 16:9 wide picture (in a vertical direction) to fit the screen size. Select by pressing the œ or √ button. Use the ▲ or ▼ button to move the picture up and down. After selecting , use the ▲ or ▼ button to magnify or reduce the picture size in a vertical direction. Zoom 4 : 3(Nor mal) Standard TV and VCR screen size having a 4:3 Aspect Ratio. 4:3 Notes • In TV, VIDEO, S-VIDEO and Component (480i) modes, all screen modes can be selected. (16:9 ➞ Panorama ➞ Zoom ➞ 4:3). • In PC/DVI mode, only 16:9 & 4:3 modes can be selected. • In Component (480p, 720p. 1080i) modes, Panorama mode can’t be selected. • In Component (480p, 720p. 1080i) modes, you can move the picture on screen by pressing the ▲ or ▼ button. (All screen modes) • Changing the screen size to Normal, or Zoom during PIP mode will cause the PIP window to disappear. 45 Freezing the Picture Still Press the STILL button on the remote control to freeze a moving picture. Press again to cancel. 46 Viewing the Picture-in-Picture Selecting the PIP Screen Picture TV Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Mode Custom Color Tone Color Control Film Mode Size PIP † More ➤ Quick way to access the PIP mode: Just press the “PIP” button on the remote control. Move PIP Source Swap Size Position Air/CATV Channel Sound Select Move Press the ENTER button, then press the ▲ or ▼ button to select “On”. The PIP image will appear in the corner of the screen. • Pressing the ▲ or ▼ button will alternate between “On” and “Off”. PIP Source Swap Size Position Air/CATV Channel Sound Select • Check if the V-Chip Lock (refer to page 103) is ON if the PIP On/Off will not function. PIP does not function when the V-Chip Lock is set to On. Change the setting to Off and try it again. : Normal : Off : 16:9 Enter Return : Off : TV √ √ √ √ √ √ √ √ : Air : 4 : Main Enter Return PIP TV Note √ √ √ √ √ √ √ PIP TV Press the ▲ or ▼ button to select “PIP”, then press the ENTER button. : Custom Move : Off Off : TV On : Air : 4 : Main Enter Return Press the MENU button to exit. O : PIP and Swap Operate X : PIP doesn’t Operate PIP Settings Main screen PIP screen TV AV 1 AV 2 AV 3 S-Video 1 S-Video 2 Component 1 Component 2 PC DVI TV AV 1 AV 2 AV 3 S-Video 1 S-Video 2 Component 1 Component 2 PC DVI 47 Selecting an External Signal You can use PIP to view a signal from an external source, such as a VCR. Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the ▲ or ▼ button to select “PIP”, then press the ENTER button. PIP Source Swap Size Position Air/CATV Channel Sound Select The signal from these inputs will not appear if you have not connected any equipment to the PDP's respective input jacks. : Normal : Off : 16:9 Enter Return : On : TV √ √ √ √ √ √ √ √ : Air : 4 : Main Enter Return PIP TV PIP Source Swap Size Position Air/CATV Channel Sound Select Move Press the ▲ or ▼ button to cycle through all of the available signal sources: “TV”, “AV1”, “AV2”, “AV3”, “S-Video1”, “S-Video2”, “Component1”, “Component2”, “PC” and “DVI”. √ √ √ √ √ √ √ PIP TV Move Press the ▲ or ▼ button to select “Source”, then press the ENTER button. : Custom : Off TV : TV AV1 AV2 AV3 S-Video1 : Air : 22 S-Video2 : Main † Enter Return PIP TV PIP Source Swap Size Position Air/CATV Channel Sound Select Move : Off … Component1 : TV Component2 PC DVI : Air : 4 : Main Enter Return Press the MENU button to exit. Note • The PIP function operates in Wide screen. 48 • Using Multi-Screen in the Normal or Zoom screen will change the size of the main screen to Wide screen. Swapping the Contents of the PIP Image and Main Image Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More ➤ Quick way to access swapping: Just press the “SWAP” button under the cover of the remote control. Move Press the ▲ or ▼ button to select “PIP”, then press the ENTER button. PIP Source Swap Size Position Air/CATV Channel Sound Select : Off : 16:9 Enter Return : On : TV : Air : 4 : Main Enter √ √ √ √ √ √ √ √ Return PIP TV PIP Source Swap Size Position Air/CATV Channel Sound Select Move : Normal √ √ √ √ √ √ √ PIP TV Move Press the ▲ or ▼ button to select “Swap”, then press the ENTER button. • The image in the PIP window will appear on the main screen, and vice versa. : Custom : On : TV : Air : 4 : Main Enter √ √ √ √ √ √ √ √ Return Press the MENU button to exit. 49 Changing the Size of the PIP Window Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More ➤ Quick way to access PIP size: Just press the “SIZE” button under the cover of the remote control. Move Press the ▲ or ▼ button to select “PIP”, then press the ENTER button. PIP Source Swap Size Position Air/CATV Channel Sound Select PIP Source Swap Size Position Air/CATV Channel Sound Select 50 Enter Return : On : TV : Air : 4 : Main Enter √ √ √ √ √ √ √ √ Return : On : TV : Air : 4 : Main Enter Return PIP TV PIP Source Swap Size Position Air/CATV Channel Sound Select Move Press the MENU button to exit. : Off : 16:9 PIP TV Move Press the ▲ or ▼ button to select option you want, then press the ENTER button. : Normal √ √ √ √ √ √ √ PIP TV Move Press the ▲ or ▼ button to select “Size”, then press the ENTER button. : Custom : On : TV : Air : 4 : Main Enter Return Changing the Location of the PIP Image Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the ▲ or ▼ button to select “PIP”, then press the ENTER button. PIP Source Swap Size Position Air/CATV Channel Sound Select PIP Source Swap Size Position Air/CATV Channel Sound Select Enter Return : On : TV : Air : 4 : Main Enter √ √ √ √ √ √ √ √ Return : On : TV : Air : 4 : Main Enter Return PIP TV PIP Source Swap Size Position Air/CATV Channel Sound Select Move : Off : 16:9 PIP TV Move Press the ▲ or ▼ button to select PIP position you want, then press the ENTER button. : Normal √ √ √ √ √ √ √ PIP TV Move Press the ▲ or ▼ button to select “Position”, then press the ENTER button. : Custom : On : TV : Air : 4 : Main Enter Return Press the MENU button to exit. 51 Selecting a Signal Source (Antenna or Cable) for PIP If the PIP source is TV while PIP is ON, you can select the broadcasting source of PIP picture separately from the main picture. Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the ▲ or ▼ button to select “PIP”, then press the ENTER button. PIP Source Swap Size Position Air/CATV Channel Sound Select PIP Source Swap Size Position Air/CATV Channel Sound Select 52 Enter Return : On : TV : Air : 4 : Main Enter √ √ √ √ √ √ √ √ Return : On : TV Air STD : Air : 4 HRC IRC : Main Enter Return PIP TV PIP Source Swap Size Position Air/CATV Channel Sound Select Move Press the MENU button to exit the menu. : Off : 16:9 PIP TV Move If an antenna is connected, the setting is “Air”. If a Cable TV system is providing the signal, press the ▲ or ▼ button until the appropriate type of cable system is selected (“STD”, “HRC” or “IRC”). : Normal √ √ √ √ √ √ √ PIP TV Move Press the ▲ or ▼ button to select “Air/CATV”, then press the ENTER button. : Custom : On : TV Air STD : Air : 4 HRC IRC : Main Enter Return Changing the PIP Channel Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. ➤ Quick way to change the PIP channel: Just press the “CH “CH Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More “ or ” button under the cover of the remote control. Move Press the ▲ or ▼ button to select “PIP”, then press the ENTER button. PIP Source Swap Size Position Air/CATV Channel Sound Select PIP Source Swap Size Position Air/CATV Channel Sound Select Enter Return : On : TV : Air : 4 : Main Enter √ √ √ √ √ √ √ √ Return : On : TV : Air ▲ : 4 ▲ : Main Enter Return PIP TV PIP Source Swap Size Position Air/CATV Channel Sound Select Move : Off : 16:9 PIP TV Move Press the ▲ or ▼ button to change the channel that appears in the PIP window. : Normal √ √ √ √ √ √ √ PIP TV Move Press the ▲ or ▼ button to select “Channel”, then press the ENTER button. : Custom : On : TV : Air ▲ : 4 11 ▲ : Main Enter Return Press the MENU button to exit. 53 Setting the MCC(My Control Color) Mode MCC (My Color Control) Modes: MCC allows users to adjust colors to according to their preferences, by adjusting skin, sky, and grass tones using the predefined settings (Standard, Custom, Turkish Blue, Emerald Green, Indian Pink) without affecting other colors on the Using the MCC Function in the Easy Control Menu Skin, sky and grass tones are easily adjustable to suit your preferences. Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the ▲ or ▼ button to select “MCC”, then press the ENTER button. √ √ √ √ √ √ √ : Normal : Off : 16:9 Enter Return MCC TV Easy Control Detail Control Move Press the ▲ or ▼ button to select “Easy Control”, then press the ENTER button. : Custom : Custom Enter Original √ √ Return Turkish Blue Easy Control Turkish Blue Move Press the œ or √ button to select among the various picture settings. The original picture (before adjustment) is shown on the left side, while the selected mode is shown on the right side. 54 Press the MENU button to exit the menu. Indian Pink √ Return Indian Pink Easy Control Turkish Blue Move Enter Original ➤ There are five MCC modes: Standard, Custom, Turkish Blue, Emerald Green and Indian Pink. Emerald Green Emerald Green Enter Indian Pink √ Return MCC Mode Characteristics Using MCC Mode, you can enjoy the vivid colors as shown below. Original ➤ Standard Picture. Emerald Green ➤ Emphasizing Mild Greens. Feel the translucent, romantic turquoise sea. Turkish Blue ➤ Emphasizing Clear Blues. Feel the clear sun shine on the blue Mediterraneansea. Indian Pink ➤ Emphasizing Warm Skin Colors. Note • Images shown above may differ from the actual adjustment on the screen. These images are presented for illustrative purposes. 55 Setting the MCC(My Control Color) Mode MCC Custom Settings Users may set the 3 MCC colors (Skin, Sky, and Grass Tones). Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the ▲ or ▼ button to select “MCC”, then press the ENTER button. Press the ▲ or ▼ button to select the desired MCC color and then press the ENTER or √ button. √ √ √ √ √ √ √ : Normal : Off : 16:9 Enter Return MCC TV Easy Control Detail Control Move Press the ▲ or ▼ button to select “Detail Control”, then press the ENTER button. : Custom : Custom Enter √ √ Return MCC TV Skin Tone Green Grass Blue Sky Reset Move 50 50 50 Enter Return ➤ The original picture (before adjustment) is shown on the left side, while the picture after adjustment is shown on the right side, and an adjustment bar on the bottom of the screen. Press the œ or √ button to adjust the settings. Changing the adjustment value will refresh the adjusted screen. Press the ▲ or ▼ button to choose other MCC colors. Original Detail Control 56 50 Skin Tone Move Press the ENTER or MENU button to confirm the changes and return to the previous menu. Adjusted Adjust Return Resetting the MCC Colors to the Factory Defaults To return to the factory default settings for MCC colors, use the Reset function. Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the ▲ or ▼ button to select “MCC”, then press the ENTER button. Easy Control Detail Control The previously adjusted MCC Colors will be reset to the factory defaults.(The default value for MCC colors is 50.) : Off : 16:9 Enter Return : Custom Enter √ √ Return MCC TV Skin Tone Green Grass Blue Sky Reset Move Press the ▲ or ▼ button to select “Reset” and press the ENTER button. : Normal √ √ √ √ √ √ √ MCC TV Move Press the ▲ or ▼ button to select “Detail Control”, then press the ENTER button. : Custom 60 35 80 Enter Return MCC TV Skin Tone Green Grass Blue Sky Reset Move 60 35 80 Enter Return 57 P Sound Control Customizing the Sound ................................................................60 Using Automatic Sound Settings ....................................................61 Choosing a Multi-Channel Sound (MTS)Soundtrack ..........................62 Using the Auto Volume ..................................................................63 Setting the TruSurround XT ............................................................64 Listening to the Sound of the Sub(PIP) Picture....................................65 Selecting the Internal Mute ............................................................66 Customizing the Sound Press the MENU button. Press the ▲ or ▼ button to select “Sound”, then press the ENTER button. Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute Move Press the ▲ or ▼ button to select “Custom”, then press the ENTER button. : Custom √ √ √ √ √ √ Stereo Off Stereo Off Enter Return Custom TV 100 300 1K Adjust Select the option (volume, balance, equalizer) to be adjusted by pressing the œ or √ button. Press the ▲ or ▼ button to reach the required setting. Press the MENU button to exit. ➤ If you make any changes to the equalizer settings, the sound Mode is automatically switched to the custom mode. 60 Move 3K 10K Return Using Automatic Sound Settings Press the MENU button. Press the ▲ or ▼ button to select “Sound”, then press the ENTER button. Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute Move Press the ENTER button to select “Mode”. Move Press the MENU button to exit. √ √ √ √ √ √ Stereo Off Stereo Off Enter Return Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute Press the ▲ or ▼ button to select “Standard”, “Music”, “Movie”, “Speech” or “Custom” sound setting, then press the ENTER button. : Custom Standard : Custom Music : Stereo Movie : Off Speech : Stereo : OffCustom Enter Return Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute Move Standard : Custom Music : Stereo Movie : Off Speech : Stereo : OffCustom Enter Return 61 Choosing a Multi-Channel Sound (MTS) Soundtrack Depending on the particular program being broadcast, you can listen to stereo, mono, or a Separate Audio Program. (SAP audio is usually a foreign-language translation. Sometimes SAP has unrelated information like news or weather.) Press the MENU button. Press the ▲ or ▼ button to select “Sound”, then press the ENTER button. Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute ➤ Quick way to access the MTS menu: Just press the “MTS” button on the remote control. Move Press the ▲ or ▼ button to select “MTS”, then press the ENTER button. Mode Custom MTS Auto Volume SRS TSXT Internal Mute Stereo Off Stereo Off Enter Return : Custom Mono Stereo OffStereo Stereo SAP Off Enter Return Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute Move : Custom Mono Stereo OffStereo Stereo SAP Off Enter Return Press the MENU button to exit. • Choose Stereo for channels that are broadcasting in stereo. • Choose Mono for channels that are broadcasting in mono, or if you are having difficulty receiving a stereo signal. • Choose SAP to listen to the Separate Audio Program, which is usually a foreign-language translation. Note • The MTS function operates in TV mode only. 62 √ √ √ √ √ √ Sound TV Move Press the ▲ or ▼ button to select “Mono”, “Stereo” or “SAP”, then press the ENTER button. : Custom Using the Auto Volume Each broadcasting station has its own signal conditions, which can make it necessary to adjust the volume every time the channel is changed. “Auto volume” lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low. Press the MENU button. Press the ▲ or ▼ button to select “Sound”, then press the ENTER button. Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute Move Press the ▲ or ▼ button to select “Auto Volume”, then press the ENTER button. Press the ▲ or ▼ button to select “On”, then press the ENTER button. • Pressing the ▲ or ▼ button will alternate between “On” and “Off”. Mode Custom MTS Auto Volume SRS TSXT Internal Mute Stereo Off Stereo Off Enter Return : Custom Stereo Off Off Stereo On Off Enter Return Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute Move √ √ √ √ √ √ Sound TV Move : Custom : Custom Stereo Off Off Stereo On Off Enter Return Press the MENU button to exit. 63 Setting the TruSurround XT TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. Trusurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats. Press the MENU button. Press the ▲ or ▼ button to select “Sound”, then press the ENTER button. Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute ➤ Quick way to access the TruSurround XT menu: Just press the “SRS TSXT” button on the remote control. Move Press the ▲ or ▼ button to select “SRS TSXT”, then press the ENTER button. Press the ▲ or ▼ button to change the setting (Off, 3D Mono or Stereo), then press the ENTER button. Mode Custom MTS Auto Volume SRS TSXT Internal Mute 4➤ 64 TruSurround XT, SRS and ( ) Symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc. Stereo Off Stereo Off Enter Return : Custom Stereo Off Stereo Off Off 3D Mono Stereo Enter Return Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute Move Press the MENU button to exit. √ √ √ √ √ √ Sound TV Move : Custom : Custom Stereo Off Stereo Off Off 3D Mono Stereo Enter Return Listening to the Sound of the Sub(PIP) Picture During the PIP feature is activating, you can listen to the sound of the sub picture. Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the ▲ or ▼ button to select “PIP”, then press the ENTER button. PIP Source Swap Size Position Air/CATV Channel Sound Select PIP Source Swap Size Position Air/CATV Channel Sound Select Move Set to Sub by pressing the ▲ or ▼ button. • You can listen to the sound of the sub picture. ➤ To listen the sound of the main picture, set to Main. : Off : 16:9 Enter Return : On : TV : Air : 4 : Main Enter √ √ √ √ √ √ √ √ Return PIP TV • Pressing the ▲ or ▼ button will alternate between “Main” and “Sub”. : Normal √ √ √ √ √ √ √ PIP TV Move Press the ▲ or ▼ button to select “Sound Select”, then press the ENTER button. : Custom : On : TV : Air : 4 Main : MainSub Enter Return PIP TV PIP Source Swap Size Position Air/CATV Channel Sound Select Move : On : TV Off On : Air Main : 4 : MainSub Enter Return 65 Selecting the Internal Mute The internal speakers can be muted in order to hear sound from external speakers you've connected. Press the MENU button. Press the ▲ or ▼ button to select “Sound”, then press the ENTER button. Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute Move Press the ▲ or ▼ button to select “Internal Mute”, then press the ENTER button. Press the ▲ or ▼ button to select “On”, then press the ENTER button. • Pressing the ▲ or ▼ button will alternate between “On” and “Off”. Mode Custom MTS Auto Volume SRS TSXT Internal Mute 70 Press the MENU button to exit. Stereo Off Stereo Off Enter Return : Custom Stereo Off Stereo Off Off On Enter Return Sound TV Mode Custom MTS Auto Volume SRS TSXT Internal Mute Move √ √ √ √ √ √ Sound TV Move : Custom : Custom Stereo Off Stereo Off Off On Enter Return P Channel Control Fine Tuning Channels....................................................................68 LNA (Low Noise Amplifier) ............................................................69 Fine Tuning Channels Use fine tuning to manually adjust a particular channel for optimal reception. Press the MENU button. Press the ▲ or ▼ button to select “Channel”, then press the ENTER button. TV Channel Air/CATV Auto Program Add/Delete Fine Tune LNA Scan Move Press the ▲ or ▼ button to select “Fine Tune”, then press the ENTER button. : Air √ √ √ √ √ √ : Off Enter Return Fine Tune Air 4 Reset Move Return Adjust Press the œ or √ button to adjust the fine tuning. Store Fine Tune Air 4 10 Reset Move To store the fine tuning setting in the TV’s memory, press the ENTER button. (A star icon(*) will appear.) To reset the fine tuning to “0”, press the ▼ button to select “Reset”, then press the ENTER button. Return Adjust Fine Tune Air 4 * 10 Reset Move 68 Press the MENU button to exit. Store Return Adjust Store LNA (Low Noise Amplifier) If the TV is operating in a weak-signal area, sometimes the LNA function can improve the reception (a low-noise preamplifier boosts the incoming signal). Press the MENU button. Press the ▲ or ▼ button to select “Channel”, then press the ENTER button. Channel TV Air/CATV Auto Program Add/Delete Fine Tune LNA Scan Move Press the ▲ or ▼ button to select “LNA”, then press the ENTER button. • Pressing the ▲ or ▼ button will alternate between “On” and “Off”. Air/CATV Auto Program Add/Delete Fine Tune LNA Scan Enter Return : Air : Off Off On Enter Return Channel TV Air/CATV Auto Program Add/Delete Fine Tune LNA Scan Move : Off √ √ √ √ √ √ Channel TV Move Press the ▲ or ▼ button to select “On”, then press the ENTER button. : Air : Air : Off Off On Enter Return Press the MENU button to exit. 69 P Connecting a PC and Operation Connecting a PC..........................................................................72 Adjusting the PC Screen................................................................76 Changing the Position of the Image................................................77 Picture Quality Adjustment ............................................................78 Information ..................................................................................81 Connecting a PC Connection to a Macintosh computer may require an adapter. PDP Power Plug Use the DVI-D connection cable. (sold separately) or DVI Cable PC Cable Audio Cable PC DVI jack (The actual configuration on your PC may be different, depending on the model.) Connecting a PC to the PDP Connect a PC (15pin) cable between the PC Output jack (or DVI jack) on the PC and the RGB IN(or DVI IN) Input jack (15p D-SUB) on the PDP. Connect a Audio cable between the Audio (RGB or DVI) on the PC and the Audio L/R (RGB or DVI) input jacks on the PDP. To watch the PC screen: 1. Turn on your PDP 2. Press the TV/VIDEO button on the remote control or SOURCE button on the front panel to select “PC”. 3. Turn on PC and check for PC system requirements. (Refer to pages 74 and 75 for PC system requirements.) 4. Adjust the PC screen. (Refer to pages 76 and 78.) 72 Pin Configuration D-Sub Cable DVI-D Cable (Digital-Only Connector) • 15Pin Signal Cable (based on protruded pin) Setting up Your PDP (Plug and Play) Our adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system, without the usual setup hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification data (EDID) using Display Data Channel (DDC) protocols. 73 How to Set up Your PC Software (Windows only) The Windows display-settings for a typical computer are shown below. However, the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.) On the windows screen, select in the following sequence : Start ➝ Settings ➝ Control Panel. When the control panel screen appears, click on “Display” and a display dialog-box will appear. Select the “Settings” tab in the display dialogbox. The two key variables that apply to the PDP-PC interface are “resolution” and “colors”. The correct settings for these two variables are: • Size (sometimes called “resolution”) :1204 x 768 pixels. • Color: “32-bit” color Shown at left is a typical screen for “Display” dialog box. If a vertical-frequency option exists on your display settings dialog box, the correct value is “60” or “60 Hz”. Otherwise, just click “OK” and exit the dialog box. Continued... 74 Notes: Both screen position and size will vary, depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: Video Signal Resolution (Dot X Line) 640 X 350 640 X 400 720 X 400 640 X 480 IBM PC / AT Compatible 800 X 600 848 X 480 1024 X 768 Vertical Frequency(Hz) Horizontal Frequency(KHz) Vertical Polarity Horizontal Polarity 70.086 85.080 85.080 70.087 85.039 59.940 72.809 75.000 85.061 56.250 60.317 72.188 75.000 85.061 60.000 72.000 75.000 60.004 70.069 75.029 84.997 31.469 37.861 37.861 31.469 37.927 31.469 37.861 37.500 43.269 35.156 37.897 48.077 46.875 53.674 29.838 36.072 37.650 48.363 56.476 60.023 63.677 N/P N/P nVidia chipset • The interlace mode is not supported. • The PDP operates abnormally if a non-standard video format is selected. • This sheet conforms to IBM/VESA regulations and is prepared on the basis of Analog Input. • The DVI Mode is supported same as above table. Notes: • When this PDP is used as a PC display, 32-bit color is supported. • Depending on the manufacturer, your PC display screen might appear different. (and depending on your particular version of Windows.) Check your PC instruction book for information about connecting your PC to a PDP. • If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 48.4kHZ (horizontal). • In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the TV/VIDEO button on the remote control or SOURCE button on the front panel to enter the VIDEO mode. Also, make sure that the PC is connected. • Connect only a PC monitor to the monitor output port while viewing the PC screen. (Otherwise, random signals might appear). 75 Adjusting the PC Screen Adjusting the R.G.B Preset: • Press the TV/VIDEO button to select “PC”. Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP † More Move Press the ▲ or ▼ button to select “Color Control”, then press the ENTER button. The “Color Control” is available only when “Color Tone” is set in the custom mode. 76 Press the MENU button to exit. : Normal : Off : 16:9 Enter √ √ √ √ √ √ √ Return Color Control TV 50 50 50 Move Press the ▲ or ▼ button to select the item you want to change, then press the ENTER button. Press the œ or √ button to change the value of the item, using the on-screen gauge as your guide. : Custom Enter Return 50 Changing the Position of the Image After connecting the PDP to your PC, adjust the position of the screen if it is not well-aligned. Preset: • Press the TV/VIDEO button to select “PC.” Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “PC”, then press the ENTER button. Image Lock Position Information Auto Adjustment Enter Return Move Return Position TV Move √ √ √ √ Position TV Move Adjust the position of screen by pressing the ▲ / ▼/ œ / √ button. Return PC TV Move Press the ENTER button to select “Position”. Enter √ √ √ √ √ √ √ √ Move Return Press the MENU button to exit. 77 Picture Quality Adjustment Picture Automatic Adjustment Preset: • Press the TV/VIDEO button to select “PC”. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “PC”, then press the ENTER button. 78 Return PC TV Image Lock Position Information Auto Adjustment Move Press the ▲ or ▼ button to select “Auto Adjustment”, then press the ENTER button. The message “Auto Adjustment in progress.” appears on the screen and the picture adjustments are automatically activated. Enter √ √ √ √ √ √ √ √ TV √ √ √ √ Enter Return Auto Adjustment Auto Adjustment in progress. Press the MENU button to exit. Air 11 Coarse Adjustment Preset: • Press the TV/VIDEO button to select “PC”. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “PC”, then press the ENTER button. Image Lock Position Information Auto Adjustment √ √ √ √ Enter Return Image Lock TV Coarse Fine Move Return PC TV Move Press the ▲ or ▼ button to select “Image Lock”, then press the ENTER button. Enter √ √ √ √ √ √ √ √ 50 Enter Return Press the ENTER button to select “Coarse”. Coarse 50 Remove picture noise (vertical stripes) on the screen by pressing the œ or √ button. (If Coarse is not set properly, vertical stripes will appear on the screen.) Press the MENU button to exit. 79 Fine Tuning (Fine) Preset: • Press the TV/VIDEO button to select “PC”. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “PC”, then press the ENTER button. Image Lock Position Information Auto Adjustment 80 Press the ▲ or ▼ button to select “Fine”, then press the ENTER button. Remove picture noise on the screen by pressing the œ or √ button. (If Fine is not set properly, noise will appear on the screen.) Press the MENU button to exit. √ √ √ √ Enter Coarse Fine Fine Return Image Lock TV Move Return PC TV Move Press the ▲ or ▼ button to select “Image Lock”, then press the ENTER button. Enter √ √ √ √ √ √ √ √ 50 Enter Return Information Preset: • Press the TV/VIDEO button to select “PC”. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “PC”, then press the ENTER button. Return PC TV Image Lock Position Information Auto Adjustment Move Press the ▲ or ▼ button to select “Information”, then press the ENTER button. The vertical, horizontal frequencies and resolution appear. Enter √ √ √ √ √ √ √ √ √ √ √ √ Enter Return Information TV Resolution H Frequency V Frequency : 800 * 600 : 38.0KHz 60.5 Hz Return Press the MENU button to exit. 81 P Time Setting Setting the Clock .......................................................................84 Setting the Sleep Timer...............................................................85 Setting the Timers ......................................................................86 Setting the Clock Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “Time”, then press the ENTER button. Clock Sleep Timer On Timer Off Timer 12 Adjust 12 Adjust 12 Adjust 84 Return Minute am/pm 00 am Move Return Minute am/pm 00 am Move Return Clock TV Hour Press the MENU button to exit. Enter √ √ √ √ Clock TV Hour Press the √ button to select “am/pm”, then press the ▲ or ▼ button to select the proper time of day (am or pm). 12 : 00 am Off Off Off Clock TV Hour Press the √ button to select “Minute”, then press the ▲ or ▼ button to select correct minute. Return Time TV Move Press the ENTER button to select “Clock”. Press the ENTER button to select “Hour”, then press the ▲ or ▼ button to select correct hour. Enter √ √ √ √ √ √ √ √ Minute am/pm 00 Move am Return Setting the Sleep Timer You can set your PDP to automatically turn off after a preset interval. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off ➤ Quick way to access the sleep timer setting: Just press the “SLEEP” button on the remote control. Move Press the ▲ or ▼ button to select “Time”, then press the ENTER button. Enter Clock Sleep Timer On Timer Off Timer 12 : 00 am Off Off Off Enter Activation -- Off Move Return Sleep Timer TV Minute Activation 30 On Move Return Sleep Timer TV Minute Activation 30 On Adjust Return Minute Adjust Press the √ button to select “Activation”, then press the ▲ or ▼ button to select “On” or “Off”. √ √ √ √ Sleep Timer TV Adjust Press the ▲ or ▼ button to select the time interval for the PDP to stay on. The interval ranges from 30 to 180 minutes. Return Time TV Move Press the ▲ or ▼ button to select “Sleep Timer”, then press the ENTER button. √ √ √ √ √ √ √ √ Move Return Press the MENU button to exit. 85 Setting the Timers This PDP can be set to turn on or off automatically at specific times that you choose. Before using the timers, you must set the PDP’s clock, as described previously. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “Time”, then press the ENTER button. Clock Sleep Timer On Timer Off Timer 12 00 am Volume Activation 10 Move Off Return On Timer TV Hour Minute am/pm 12 00 am Air 3 Adjust Volume Activation 10 Move Off Return On Timer TV Hour Minute am/pm 12 00 am Channel Air 3 Adjust 86 Return am/pm Channel Enter √ √ √ √ Minute Adjust Press the √ button to select “am/pm”, then press the ▲ or ▼ button to select the proper time of day (am or pm). 12 : 00 am Off Off Off Hour Air 3 Return On Timer TV Channel Press the √ button to select “Minute”, then press the ▲ or ▼ button to select correct minute. Enter Time TV Move Press the ▲ or ▼ button to select “On Timer”. Press the ENTER button to select “Hour”, then press the ▲ or ▼ button to select correct hour. √ √ √ √ √ √ √ √ Volume Activation 10 Move Off Return 6 Press the √ button to select “Channel”, then press the ▲ or ▼ button to select the channel you want when PDP turns on. On Timer TV Hour Minute am/pm 12 00 am Channel Air 3 Adjust Press the √ button to select “Volume”, then press the ▲ or ▼ button to select the volume level you want when PDP turns on. Return Minute am/pm 12 00 am Adjust Volume Activation 10 Move Off Return On Timer TV Hour Minute am/pm 12 00 am Channel Air 3 Adjust Move Off Hour Air 3 10 On Timer TV Channel Press the √ button to select “Activation”, then press the ▲ or ▼ button to select “On” or “Off”. Volume Activation Volume Activation 10 Move Off Return If you want to set Off Time, press the ▲ or ▼ button to select “Off Time”. Set the “Off Time” just as you set “On Time”. 10 Press the MENU button to exit. 87 P Function Description Selecting a Menu Language .....................................................90 Digital Noise Reduction ...........................................................91 Selecting the Film Mode ...........................................................92 Using the Color Weaknees Enhancement Option.........................93 Setting the Melody Sound ........................................................94 Setting the Blue Screen.............................................................95 Setting the Fan ........................................................................96 Viewing Closed Captions .........................................................97 Using the V-Chip .....................................................................98 Selecting a Menu Language Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ENTER button to select “Language”. Language : English English Time Français Caption Español Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Press the ▲ or ▼ button to select the appropriate language: “English”, “Français” or “Español”. 90 Press the MENU button to exit. Enter Return Configuration TV Langue : Français English Heure Français Sous-titres Español Réduct. bruit num. : Marche puce V Divers PC Faibl. couleurs : Arrêt Dépl Return Setup TV Move Enter √ √ √ √ √ √ √ √ Entrée Retour Digital Noise Reduction If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “Digital NR”, then press the ENTER button. Language : English Time Caption Digital NR : On Off V-Chip On Miscellaneous PC Color Weakness : Off Enter Return Setup TV Language : English Time Caption Digital NR : On Off V-Chip On Miscellaneous PC Color Weakness : Off Move Return Setup TV Move Press the ▲ or ▼ button to select “On” or “Off”, then press the ENTER button. Enter √ √ √ √ √ √ √ √ Enter Return Press the MENU button to exit. 91 Selecting the Film Mode On: Automatically senses and processes film signals from all sources and adjusts the picture for optimum quality. Off: Switches off the Film mode. Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Picture TV Mode Custom Color Tone Color Control Film Mode Size PIP ▼ More Move Press the ▲ or ▼ button to select “Film Mode”, then press the ENTER button. Mode Custom Color Tone Color Control Film Mode Size PIP ▼ More Mode Custom Color Tone Color Control Film Mode Size PIP ▼ More Press the MENU button to exit. Note • Film mode is supported in TV, VIDEO, S-VIDEO and COMPONENT 480i. 92 : Off : 16:9 Enter Return : Custom : Normal : Off Off : 16:9 On Enter Return Picture TV Move : Normal √ √ √ √ √ √ √ Picture TV Move Press the ▲ or ▼ button to select “On” or “Off”, then press the ENTER button. : Custom : Custom : Normal : Off Off : 16:9 On Enter Return Using the Color Weaknees Enhancement Option This option adjusts the Red, Blue or Green color to enhance the image according to the user's particular color weakness. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : On Move Press the ▲ or ▼ button to select “Color Weakness ”, then press the ENTER button. Color Weakness : Off Return Color Weakness : On Off On Move Enter √ Color Weakness TV • Pressing the ▲ or ▼ button will alternate between “On” and “Off”. Press the ▲ or ▼ button to select the item you wish to change, then press the ENTER button. Press the œ or √ button to change the value of the item. Return Color Weakness TV Move Press the ENTER button to select “On”, then press the ENTER button. You will also see the items “R“, “G“, and “B“. Enter √ √ √ √ √ √ √ √ Enter Return Color Weakness Move Adjust Return Press the MENU button to exit. 93 Setting the Melody Sound You can hear clear melody sound when the television is powered on or off. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : On Move Press the ▲ or ▼ button to select “Miscellaneous”, then press the ENTER button. Press the ▲ or ▼ button to select “Melody”, press the ENTER button. Melody Plug & Play Blue Screen Fan : Off : Off Move Enter 94 : On √ √ √ √ Return Miscellaneous TV Melody Plug & Play Blue Screen Fan : On Off On : Off : Off Enter Return Miscellaneous TV Melody Plug & Play Blue Screen Fan Move Press the MENU button to exit. Return Miscellaneous TV Move Press the ▲ or ▼ button to select “On” or “Off”, then press the ENTER button. Enter √ √ √ √ √ √ √ √ : On Off On : Off : Off Enter Return Setting the Blue Screen If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the “Blue Screen“ mode to “Off“. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : On Move Press the ▲ or ▼ button to select “Miscellaneous”, then press the ENTER button. Press the ▲ or ▼ button to select “Blue Screen”, Press the ENTER button. ➤ Blue Screen is displayed when there is no signal from an external device in the External Mode, regardless of the Blue Screen Setting. Melody Plug & Play Blue Screen Fan : Off : Off Move Enter : On √ √ √ √ Return Miscellaneous TV Melody Plug & Play Blue Screen Fan : On : On Off : On On Enter Return Miscellaneous TV Melody Plug & Play Blue Screen Fan Move Return Miscellaneous TV Move Press the ▲ or ▼ button to select “On” or “Off”, then press the ENTER button. Enter √ √ √ √ √ √ √ √ : On : On Off : On On Enter Return Press the MENU button to exit. 95 Selecting the Fan Operates or stops the TV’s internal Fan. What is the Fan : Fans inside the TV are used to reduce the temperature of the tops and the front of the TV. To reduce the noise of the fan, you may stop the fan by setting the Fan to “Off”. The temperature of the top and the front of the TV may increase when you watch the TV for a long period of time while the fan is stopped, but the TV will operate normally. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : On Move Press the ▲ or ▼ button to select “Miscellaneous”, then press the ENTER button. Press the ▲ or ▼ button to select “Fan”, then Press the ENTER button. Melody Plug & Play Blue Screen Fan : Off : Off Move Enter 96 : On √ √ √ √ Return Miscellaneous TV Melody Plug & Play Blue Screen Fan : On : Off : On Off On Enter Return Miscellaneous TV Melody Plug & Play Blue Screen Fan Move Press the MENU button to exit. Return Miscellaneous TV Move Press the ▲ or ▼ button to select “On” or “Off”, then press the ENTER button. Enter √ √ √ √ √ √ √ √ : On : Off : On Off On Enter Return Viewing Closed Captions Your TV decodes and displays the closed captions that are broadcast with certain TV shows. These captions are usually subtitles for the hearing impaired or foreign language translations. All VCRs record the closed caption signal from television programs, so home-recorded video tapes also provide closed captions. Most prerecorded commercial video tapes provide closed captions as well. Check for the closed caption symbol in your television schedule and on the tape’s packaging: Note: The Caption feature does not work with DVD or DTV signals. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Press the ▲ or ▼ button to select “Caption”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ENTER button to select “Caption”. Press the ▲ or ▼ button to turn closed caption on/off, then press the ENTER button. Caption Mode Channel Field Caption Mode Channel Field On Off Caption On Enter Return On Caption Caption 1 Text Enter Return Caption TV Caption Mode Channel Field Move Caption TV Move Depending on the particular broadcast, it might be necessary to make changes to “Channel” and “Field”: Press the ▲ / ▼/ œ / √ button to make the changes. (Follow the same procedure as in steps 3 above.) Return Caption TV Move Press the ▲ or ▼ button to select “Mode”, then press the ENTER button. Press the ▲ or ▼ button to select “Text” or “Caption”, then press the ENTER button. Enter √ √ √ √ √ √ √ √ On Caption 1 1 1 2 Enter Return Press the MENU button to exit. Note • Different channels and fields display different information: Field 2 carries additional information that supplements the information in Field 1. (For example, Channel 1 may have subtitles in English, while Channel 2 has subtitles in Spanish.) 97 Using the V-Chip The V-Chip feature automatically locks out programs that are deemed inappropriate for children. The user must enter a PIN (personal ID number) before any of the V-Chip restrictions are set up or changed. Note: When the V-chip feature is activated, the PIP and auto channel program features do not function. Setting Up Your Personal ID Number (PIN) Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “V-Chip”, then press the ENTER button. The message “Enter PIN” will appear. Enter your 4 digit PIN number. Enter Return V-Chip TV Enter PIN Note: The default PIN number of a new TV set is “0-0-0-0”. Enter PIN The “V-Chip” screen will appear. Press the ▲ or ▼ button to select “Change PIN”, then press the ENTER button. TV Return Enter New PIN TV Return Change PIN Confirm New PIN Enter PIN Change PIN Enter PIN The Change PIN screen will appear. Choose any 4 digits for your PIN and enter them. As soon as the 4 digits are entered, the “Confirm New PIN” screen appears. Re-enter the same 4 digits. When the Confirm screen disappears, your PIN has been memorized. √ √ √ √ √ √ √ √ Return Press the MENU button to exit. Note • If you forget the PIN, press the remote-control buttons in the following sequence, which resets the pin to 0-0-0-0 : Power Off. ➔ Mute ➔ 8 ➔ 2 ➔ 4 ➔ Power On. 98 How to Enable/Disable the V-Chip Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “V-Chip”, then press the ENTER button. The message “Enter PIN” will appear. Enter your 4 digit PIN number. Enter Return V-Chip TV Enter PIN Enter PIN The “V-Chip” screen will appear. To enable the V-Chip feature, press the ENTER button so that the “V-Chip Lock” field is “On”. (Pressing the ▲ or ▼ button will alternate between “On” and “Off”.) Return V-Chip TV V-Chip Lock : Off Off TV Parental Guidelines On MPAA Rating Change PIN Move √ √ √ √ √ √ √ √ Enter Return Press the MENU button to exit. 99 How to Set up Restrictions using the “TV guidelines” First, set up a personal identification number (PIN), and enable the V-Chip. (See previous section.) Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating. Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “V-Chip”, then press the ENTER button. The message “Enter PIN” will appear. Enter your 4digit PIN number. Enter Enter PIN Enter PIN TV 100 TV-Y TV-Y7 Young children Children 7 and over TV-G TV-PG TV-14 TV-MA General audience Parental guidance Viewers 14 and over Mature audience TV Return TV Parental Guidelines Move The “TV Parental Guidelines” screen will appear. Press the ▲ or ▼ button to select one of the six ages based categories: Return V-Chip TV The “V-Chip” screen will appear. Press the ▲ or ▼ button to select “TV Parental Guidelines”, then press the ENTER button. √ √ √ √ √ √ √ √ Enter Return TV Parental Guidelines Move Enter Return 5 At this point, one of the TV-Ratings is selected. Press the ENTER button. Depending on your existing setup, a symbol will be selected. (Blank = Unblocked, = Blocked) While “ ” is selected, press the ▲ or ▼ button to block the category. To select a different TV-Rating, press the ▲ or ▼ button and then repeat the process. TV TV Parental Guidelines Move Enter Return Note 1: The TV-Y7, TV-PG, TV-14 and TV-MA have additional options. See the next step to change any of the following sub-ratings: FV: Fantasy violence D: Sexually Suggestive Dialog L: Adult Language S: Sexual situation V: Violence Note 2: The V-Chip will automatically block certain categories that are “more restrictive”. For example, if you block “TV-Y” category, then TV-Y7 will automatically be blocked. Similarly, if you block the TV-G category, then all the categories in the “young adult” group will be blocked (TV-G, TV-PG, TV-14 and TV-MA). The sub-ratings (D, L, S, V) work together similarly. (See next section.) How to set the FV, D, L, S and V sub-ratings. First, select one of these TV-Ratings: TV-Y7, TV-PG, TV-14 or TV-MA (See Step 4, on previous page). Next, while the TV-Rating is selected, repeatedly press the ENTER button. This will cycle through the available sub-ratings (FV, L, S, D or V). A symbol “ ” will be displayed for each sub-rating. While “ ” is selected, press the ▲, ▼, œ, or √ button to change the sub-rating. To select a different TV-Rating, press the ▲ or ▼ button and then repeat the process. Note: The V-chip will automatically block certain categories that are “More restrictive” . For example, if you block “L” sub-rating in TV-PG, then the “L” sub-ratings in TV-14 and TVMA will automatically be blocked. Press the MENU button to clear all the screens. (Or proceed to the next section, and set up additional restrictions based on the MPAA codes). Note • These categories consist of two separate groups: TV-Y and TV-Y7 (young children through age 7), and TV-G through TV-MA (everybody else). The restrictions for these two groups work independently: If a household includes very young children as well as young adults, the TV guidelines must be set up separately for each age group. (See next step.) 101 How to Set up Restrictions using the MPAA Ratings: G, PG, PG-13, R, NC-17, X The MPAA rating system uses the Motion Picture Association of America (MPAA) system, and its main application is for movies. When the V-Chip lock is on, the TV will automatically block any programs that are coded with objectionable ratings (either MPAA or TV-Ratings). Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Setup TV Language : English Time Caption Digital NR : On V-Chip Miscellaneous PC Color Weakness : Off Move Press the ▲ or ▼ button to select “V-Chip”, then press the ENTER button. The message “Enter PIN” will appear. Enter your 4 digit PIN number. Enter Return V-Chip TV Enter PIN Enter PIN The “V-Chip” screen will appear. Press the ▲ or ▼ button to select “MPAA Rating”, then press the ENTER button. General audience (no restrictions). PG Parental guidance suggested. PG-13 PG-13 (Parents strongly cautioned). R (Restricted. Children under 17 should be accompanied by an adult). Return MPAA Rating TV Move The “MPAA Rating” screen will appear. Repeatedly press the ▲ or ▼ button to select a particular MPAA category. Pressing the ▲ or ▼ button will cycle through the MPAA categories: √ √ √ √ √ √ √ √ Enter Return MPAA Rating TV Move Enter Return NC-17 No children under age 17. X (Adults only). NR Not rated. While a particular category is selected, press the ▲ or ▼ button to activate it. A selected symbol “ ” will be displayed. Press the ▲ or ▼ button to select “ ”. Note: The V-Chip will automatically block any category that is “more restrictive”. For example, if you block the “PG-13” category, then “R”, “NC-17” and “X” will automatically be blocked also. 102 How to Reset the TV after the V-Chip Blocks a Channel (“Emergency Escape”) If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the following message will appear: “Excessive rating”. To resume normal viewing, tune to a different channel using the number buttons. Under certain conditions (depending on the rating of the local TV programs) the V-Chip might lock out all the channels. In this case, use the V-Chip function for an “emergency escape”: Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Press the ▲ or ▼ button to select “V-Chip”, then press the ENTER button. Enter your PIN number, and press the √ button to temporarily disable the V-Chip Lock. 103 P Appendix Troubleshooting..........................................................................106 Care and Maintenance ..............................................................107 Specifications ............................................................................108 Troubleshooting Before you call a service technician, please scan this list of problems and possible solutions. It may save you time and money. Problem 106 Possible Solution Poor picture. Check all wire connections. Your Remote control does not operate the PDP. Press the “MODE” button to put your remote control in the “TV” mode. The PDP won’t turn on. Check if the power plug is connected. There is no screen image. Check to see that both the PDP and the source are plugged in and turned on. The image is too light or too dark. Adjust the Brightness or Contrast settings. The image is too large or too small. Adjust the Size settings. Care and Maintenance With proper care, your PDP will give you many years of service. Please follow these guidelines to get the maximum performance from your PDP. Identifying Problems • • • • Do not put the PDP near extremely hot, cold, humid or dusty places. Do not put the PDP near appliances that create magnetic fields. Keep the ventilation openings clear. Do not place the PDP on a rough and slanted surface, such as cloth or paper. Liquids • Do not place liquids near or on the PDP. Cabinet • Never open the cabinet or touch the parts inside. • Wipe your PDP with a clean, dry cloth. Never use water, cleaning fluids, wax, or chemicals. • Do not put heavy objects on top of the cabinet. Temperature • If your PDP is suddenly moved from a cold to a warm place, unplug the power cord for at least two hours so that moisture that may have formed inside the unit can dry completely. 107 Specifications Exterior design and product specifications are subject to change without prior notice to improve the performance of this product. HP-P4261 Model Dimensions Display Remote Control Weight Display Remote Control Voltage Power Consumption Number of Pixels Screen Size ANTENNA input VIDEO input 1257 (W) X 84 (D) X 740 (H) mm / 49.5(W) X 3.3 (D) X 29.1 (H) inches 59 (W) X 22 (D) X 209 (H) mm / 2.3 (W) X 0.9 (D) X 8.2 (H) inches 44kg / 971bs 164g / 0.361bs (including batteries) AC 120V~, 60Hz 400 W 1366(H) x 768(V) 127 Cm/50 inches (16:9) VHF, UHF (75Ω unbalanced) AV1 AV2 AV3(SIDE) S-VIDEO 1 S-VIDEO 2 (SIDE) COMPONENT 1 - 480i / 480p / 720p / 1080i COMPONENT 2 - 480i / 480p / 720p / 1080i PC (MINI D-SUB 15P) DVI-D AUDIO input AV1 AV2/ S-VIDEO 1 AV3 (SIDE) / S-VIDEO 2 (SIDE) COMPONENT 1 COMPONENT 2 PC DVI-D 108 Monitor Output VIDEO, AUDIO(L/R) Speaker Output 15W+15W (8 Ω) Memo 109 Memo 110 Memo 111 1-800-SAMSUNG (1-800-726-7864) Samsung Electronics America Service Division 400 Valley Road, Suite 201 Mount Arlington, NJ 07856 www.samsungusa.com Samsung Electronics Canada Inc. Samsung Customer Care 7037 Financial Drive Mississauga, Ontario L5N 6R3 www.samsung.ca BN68-00678A-00
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2004:03:14 16:44:50Z Modify Date : 2004:04:22 11:04:36-03:00 Page Count : 79 Creation Date : 2004:03:14 16:44:50Z Mod Date : 2004:04:22 11:04:36-03:00 Producer : Acrobat Distiller 5.0.5 for Macintosh Author : 1004 Metadata Date : 2004:04:22 11:04:36-03:00 Creator : 1004 Title : BN68-00678A-00_cover Has XFA : NoEXIF Metadata provided by EXIF.tools