Samsung Electronics Co RPMR500 Zigbee Module User Manual RP MR500 Manual final

Download:
Mirror Download [FCC.gov]
Document ID	1657087
Application ID	3D0JkTXnVaRIUWB22/BfOQ==
Document Description	manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.69kB (121087 bits)
Date Submitted	2012-03-15 00:00:00
Date Available	2012-09-11 00:00:00
Creation Date	2012-03-09 13:57:04
Producing Software	Acrobat Distiller 10.1.2 (Windows)
Document Lastmod	2012-03-15 09:32:19
Document Title	Microsoft Word - RP-MR500_Manual_final
Document Creator	PScript5.dll Version 5.2.2
Document Author:	B9CEC3B6

RP-MR500 Manual
1. INTRODUCTION
RP-MR500 is a full single-chip solution that is compliant to the specification of
IEEE802.15.4 and ZigBee specifications and is a complete wireless solution for
ZigBee applications such as home control and sensor network. It consists of RF
transceiver with baseband modem, a hardwired MAC and an embedded 8051
microcontroller with internal flash memory for application program. It also
includes several general-purpose I/O pins and many peripheral devices such as
timer and UART. The chip targets very low power and low voltage applications.
2. APPLICATIONS
- Home Automation and Security
- Automatic Meter Reading
- Factory Automation and Motor Control
- Replacement for legacy wired UART
- Energy Management
- Remote Keyless Entry with Acknowledgement
- Health-care equipments
- Pc peripherals and Toys
3. FEATURES
RF Transceiver
- Single-chip 2.4GHz ZigBee RF Transceiver module
- Low Power Consumption
- Low Operation Voltage of 1.9V
- high Sensitivity (-98dBm)
- On-chip VCO, LNA, and PA
- Programmable Output Power Max. +6dBm
- O-QPSK Modulation
- Scalable Data Rate: 250Kbps/500K/1M
- RSSI Measurement
- Compliant to IEEE802.15.4
8051-Compatible Microcontroller
- 8051 Compatible Microcontroller
- 96KB Embedded Flash Memory
- 8KB Data Memory
- 128-byte CPU dedicated Memory
- 1KB Boot ROM
- 24 General Purpose I/Os
- On-chip Power-on-Reset
- 4-channel 12-bit ADC
- ISP (In System Programming)
- Internal Temperature Sensor
Clock Inputs & Power
- 16MHz Crystal for System Clock
- Separate On-chip Regulators for Analog and Digital Circuitry
- Power Supply Range for Internal Regulator
- Battery Monitoring Support
4. SPECIFICATION
1) Description
Item
Description
Application
Transceiver Module
Frequency Range
2.425 ~ 2.475 GHz (ISM Band)
I/O Supply Voltage
1.9~3.6V (Recommend)
Current
50 mA
Operating Temperature
-40 ~ 85℃
Standard Spec.
IEEE802.15.4
Type
SMD Type
Size
24 x 41 x 4 mm
2) Electrical specifications
Parameter
RF Frequency Range
Min
Typ
2425
Max
Unit
2475
MHz
RF Bandwidth
MHz
Channel Bandwidth
MHz
RF Output Power
dBm
Receiver Sensitivity
(PER≤1%, Packet length of 22-byte)
Normal mode (250 kbps)
-98
Maximum Input Level
dBm
10
dBm
Current : RF Receive Mode
35
mA
Current : RF Transmit Mode
45
mA
Current : Sleep Mode
25
90
uA
5. Module Dimension
6. PIN Description
Terminal
NAME
Interface
I/O
Description
ACH0
Analog
I/O
Sensor ADC input
ACH1
Analog
I/O
Sensor ADC input
ACH2
Analog
I/O
Sensor ADC input
ACH3
Analog
I/O
Sensor ADC input
AVDD_1.5V
Power
I/O
1.5V Power Supply input/output
AGND
Ground
RF Ground
MS0
Digital
Mode select
MS1
Digital
Mode select
MS2
Digital
Mode select
10
MSV
Digital
Mode select of voltage(0=1.5V)
11
RESETB
Digital
Reset (Active Low)
12
3V_IN
Power
3V Power supply
13
DGND
Ground
Ground for digital core and I/O
14
P1[7]
Digital
Port P1.7GPO/P0AND/TRSW
15
P1[6]
Digital
Port P1.6/TRSWB
16
P1[5]
Digital
Port P1.5
17
P1[4]
Digital
Port P1.4 /QUADZB/Sleep Timer OSC Buffer Input.
18
P1[3]
Digital
Port P1.3/QUADZA/Sleep Timer OSC Buffer Output/RTCLKOUT
19
P1[2]
Digital
Port P1.2
20
P1[1]
Digital
Port P1.1/TXD1
21
P1[0]
Digital
Port P1.0/RXD1
22
P3[7]
Digital
Port P3.7/12mA Drive capability /PWM3/CTS1/SPICSN(slave only)
23
P3[6]
Digital
Port P3.6/12 mA
Drive capability /PWM2/RTS1/SPICLK
Terminal
NAME
Interface
I/O
Description
24
P3[5]
Digital
Port P3.5/T1/CTS0/QUADYB/SPIDO
25
P3[4]
Digital
Port P3.4/T0/RTS0/QUADYA/SPIDI
26
P3[3]
Digital
Port P3.3/INT1(active low)
27
P3[2]
Digital
Port P3.2/INT0(active low)
28
P3[1]
Digital
Port P3.1/TXD0/QUADXB
29
P3[0]
Digital
Port P3.0/RXD0/QUADXA
30
DGND
Ground
Ground for digital core and I/O
31
DVDD_1.5V
Power
I/O
1.5V Power Supply input/output
32
P0[7]
Digital
Port P0.7/I2STX_MCLK
33
P0[6]
Digital
Port P0.6/I2STX_BCLK
34
P0[5]
Digital
Port P0.5/I2STX_LRCK
35
P0[4]
Digital
Port P0.4/I2STX_DO
36
P0[3]
Digital
Port P0.3/I2SRX_MCLK
37
P0[2]
Digital
Port P0.2/I2SRX_BCLK
38
P0[1]
Digital
Port P0.1/I2SRX_LRCK
39
P0[0]
Digital
Port P0.0/I2SRX_DI
40
NC
NC
No Connection
41
NC
NC
No Connection
42
AGND
Ground
RF Ground
43
DGND
Ground
Ground for digital core and I/O
44
DGND
Ground
Ground for digital core and I/O
45
AGND
Ground
RF Ground
7. Contact Information
RadioPulse Inc.
3rd fl., Hans II bldg., 111-6 Seongnae-dong, Gangdong-gu, Seoul, 134-883, Korea
Tel : +82 2 478 2963~5
Fax : +82 2 478 2966~7
FCC Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC
compliance requirement of the end product, which integrates this module.
Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
The end user has to be informed that any changes or modifications not expressly approved by
the manufacturer could void the user's authority to operate this equipment. If the size of the end
product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be
available in the users manual: This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful interference and (2)
this device must accept any interference received, including interference that may cause undesired
operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC
ID:A3LRPMR500". If the size of the end product is larger than 8x10cm, then the following FCC
part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC
rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including interference that may
cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : 
Create Date                     : 2012:03:09 13:57:04+09:00
Modify Date                     : 2012:03:15 09:32:19+09:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2012:03:15 09:32:19+09:00
Producer                        : Acrobat Distiller 10.1.2 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - RP-MR500_Manual_final
Creator                         : 
Document ID                     : uuid:c83f9ffb-2473-48e4-99b8-5e9f767b74cf
Instance ID                     : uuid:00017cb6-6b73-4fa8-9f3a-47f7c87832cc
Page Count                      : 8

EXIF Metadata provided by EXIF.tools