Samsung (2.6 MB) SMH8165 XAA DE68 03587A 04 EN 120725
User Manual: Samsung (2.6 MB) Samsung SMH1622S Installation Manual | Manual Device
Open the PDF directly: View PDF 
.
Page Count: 20
| Download | |
| Open PDF In Browser | View PDF |
Installation Instructions Over the Range Microwave Oven BEFORE YOU BEGIN (Read these instructions completely and carefully.) IMPORTANT Save these instructions for local inspector’s use. IMPORTANT Observe all governing codes and ordinances. • Note to Installer - Be sure to leave these instructions with the Consumer. • Note to Consumer - Keep these instructions for future reference. • Skill level - Installation of this appliance requires basic mechanical and electrical skills. • Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under the Warranty. READ CAREFULLY. KEEP THESE INSTRUCTIONS. SMH8165_XAA DE68-03587A-04-EN_120725.indd 1 2012-07-25 �� 8:05:23 Contents General information Step-by-step installation guide Important safety instructions....................... 3 1. Placement of the mounting plate............. 8 Electrical requirements................................. 3 A. Removing the microwave oven from the carton/removing the mounting plate......... 8 Hood exhaust................................................. 4 B. Finding the wall studs................................. 8 Damage – Shipment/Installation.................. 6 C. Determining wall plate location under your cabinet........................................................ 9 Parts included................................................ 6 D. Aligning the wall plate............................... 10 Tools you will need......................................... 7 Im T o co b o g el R em 2. Ventilation types (choose a, b or c)........ 11 Mounting space............................................. 7 A. Outside top exhaust (vertical duct).......... 12 A1. Installation procedure for exhaust adaptor and proper damper operation check.................................................. 12 A2. Adjust the exhaust adaptor............... 12 B. Recirculating (non-vented ductless)........ 13 B1. Adapting microwave blower for recirculation....................................... 13 B2. Installing the charcoal filter............... 13 C. Outside back exhaust (horizontal duct)... 14 C1. Adapting microwave blower for outside back exhaust...................................... 14 3. Installation................................................ 15 A. Preparing the rear wall for outside back exhaust..................................................... 15 B. Attach the mounting plate to the wall...... 15 C. Use top cabinet template for preparation of top cabinet...................................................16 D. Mount the microwave oven...................... 16 E. Connecting ductwork for outside top exhaust..................................................... 17 Before you use your microwave................. 18 2 SMH8165_XAA DE68-03587A-04-EN_120725.indd 2 2012-07-25 �� 8:05:23 C su c o lo 1 C c su m N sa in IM P B O 8 8 8 9 0 1 2 2 2 General information Important safety instructions This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies. Insure proper ground exists before use CAUTION: For personal safety, remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury. You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded. Where a standard two-prong wall receptacle is encountered, it is very important to have it replaced with a properly grounded threeprong wall receptacle, installed by a qualified electrician. 3 3 3 4 e 4 5 5 5 6 6 7 8 The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance. CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this 59 pound product, plus additional oven loads of up to 50 pounds or a total weight of 109 pounds. DO NOT, UNDER ANY CIRCUMSTANCES, CUT, DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD. CAUTION: For personal safety, this product cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet AND a wall. Electrical requirements NOTE: For easier installation and personal safety, it is recommended that two people install this product. Product rating is 120 volts AC, 60 Hertz, 13.5 amps and 1.58 kilowatts.This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a separate 15 ampere branch circuit single grounded outlet. The outlet box should be located in the cabinet above the microwave oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code. IMPORTANT–PLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK. 3 SMH8165_XAA DE68-03587A-04-EN_120725.indd 3 2012-07-25 �� 8:05:23 General information Hood exhaust NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 11. N d ro O R OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. DUCT PIECES EQUIVALENT LENGTH x NUMBER USED = EQUIVALENT LENGTH Roof Cap 24 ft. x (1) = 24 ft. N th p he sw E T st 12 ft. Straight Duct (6˝ Round) 12 ft. x (1) = 12 ft. Rectangular-toRound Transition Adaptor* 5 ft. x (1) = 5 ft. Total Length = 41 ft. Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood. * IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper. OUTSIDE BACK EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. EQUIVALENT LENGTH* x NUMBER USED = EQUIVALENT LENGTH Wall Cap 40 ft. x (1) = 40 ft. 3 ft. Straight Duct (3 ¼˝ x 10˝ Rectangular) 3 ft. x (1) = 3 ft. 90 ° Elbow 10 ft. x (2) = 20 ft. Total Length = 63 ft. DUCT PIECES Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood. NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust. 4 SMH8165_XAA DE68-03587A-04-EN_120725.indd 4 2012-07-25 �� 8:05:24 If tr th General information For satisfactory air movement, the total duct length of 3 ¼˝ x 10˝ rectangular or 6˝ diameter round duct should not exceed 140 equivalent feet. Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully. Elbows, transitions, wall and roof caps, etc., present additional resistance to airflow NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure dampers swing freely and nothing is blocking the ducts. and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total duct length, add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections. The chart below shows you how to calculate total equivalent ductwork length using the approximate feet of equivalent length of some typical ducts. Exhaust connection: The hood exhaust has been designed to mate with a standard 3 ¼˝ x 10˝ rectangular duct. If a round duct is required, a rectangular-to-round transition adaptor must be used. Do not use less than a 6˝ diameter duct. EQUIVALENT LENGTH x Rectangular-to-Round Transition Adaptor* 5 ft. x ( ) = ft. Wall Cap 40 ft. x ( ) = ft. 90 ° Elbow 10 ft. x ( ) = ft. 45 ° Elbow 5 ft. x ( ) = ft. 90 ° Elbow 25 ft. x ( ) = ft. 45 ° Elbow 5 ft. x ( ) = ft. Roof Cap 24 ft. x ( ) = ft. Straight Duct 6˝ Round or 3 ¼˝ x 10˝ Rectangular 1 ft. x ( ) = ft. = ft. DUCT PIECES e red Maximum duct length: NOTE: If you need to install ducts, note that the total duct length of 3 ¼˝ x 10˝ rectangular or 6˝ diameter round duct should not exceed 140 equivalent feet. NUMBER USED Total Ductwork * IMPORTANT: If a rectangular-toround transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper. = EQUIVALENT LENGTH Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood. 5 SMH8165_XAA DE68-03587A-04-EN_120725.indd 5 2012-07-25 �� 8:05:24 General information Damage – Shipment/Installation Tools you will need • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. • If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer. Parts included HARDWARE PACKET PART ADDITIONAL PARTS QUANTITY Wood Screws (¼˝ x 2˝) PART TOP CABINET TEMPLATE 1 REAR WALL TEMPLATE Toggle Bolts (and wing nuts) (3/16˝ x 3˝) 2 Self-aligning Machine Screws (¼˝-28 x 3 ¼˝) 2 Nylon Grommet (for metal cabinets) 1 You will find the installation hardware contained in a packet with the unit. Check to make sure you have all these parts. QUANTITY Top Cabinet Template 1 Rear Wall Template 1 Installation Instructions 1 Separately Packed Grease Filters 2 Exhaust adaptor 1 NOTE: Some extra parts are included. 6 SMH8165_XAA DE68-03587A-04-EN_120725.indd 6 2012-07-25 �� 8:05:25 Mounting space General information Tools you will need #1 and #2 Phillips screwdriver Pencil Ruler or tape measure and straight edge Carpenter square (optional) Tin snips (for cutting damper, if required) Scissors (to cut template, if necessary) Electric drill with 3/16˝, ½˝ and ⅝˝ drill bits Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Gloves Saw (saber, hole or keyhole) Stud finder or Hammer (optional) Safety goggles Level Duct and masking tape Mounting space 12˝ max. Bottom edge of cabinet needs to be 30˝ or more from the cooking surface. 16 ½˝ 30˝ 2˝ 30˝ min. Backsplash NOTES: • The space between the cabinets must be 30˝ wide and free of obstructions. • This microwave oven is for installation over ranges up to 36˝ wide. • If you are going to vent your microwave oven to the outside, see Hood Exhaust Section for exhaust duct preparation. • When installing the microwave oven beneath smooth flat cabinets be careful to follow the instructions on the top cabinet template for power cord clearance. • Maximum cabinet depth above and beside the unit is 12˝. • The dimensions provided are the minimum required for mounting the microwave oven. Local codes and practical use of the range will likely require more than 13.5˝ shown between the range and the bottom of the microwave. 7 SMH8165_XAA DE68-03587A-04-EN_120725.indd 7 2012-07-25 �� 8:05:26 Step-by-step installation guide 1. Placement of the mounting plate A. Removing the microwave oven from the carton/removing the mounting plate C B. Finding the wall studs P Wall Studs 1. Remove the installation instructions, Exhaust adaptor, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven. Center 2. Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam. 1. Find the studs, using one of the following methods: A. Stud finder–a magnetic device which locates nails. Carton OR B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location. Styrofoam 2. After locating the stud(s), find the center by probing the wall with a small nail to find the edges of the stud. Then place a mark halfway between the edges. The center of any adjacent studs should be 16˝ or 24˝ from this mark. 3. Draw a line down the center of the studs. 3. Pull the carton up and off the oven. 4. Remove and properly discard plastic bags. Screws Screws Screws Screws Mounting Plate Mounting Plate THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD. 5. Remove the 2 screws from the mounting plate. This plate will be used as the rear wall template and for mounting. NOTE: You will have to reuse two screws in original loction of outcase after removing mounting plate. 8 SMH8165_XAA DE68-03587A-04-EN_120725.indd 8 2012-07-25 �� 8:05:27 P c s Step-by-step installation guide C. Determining wall plate location under your cabinet Plate position – beneath flat bottom cabinet Plate position – beneath framed recessed cabinet bottom 16-1/2 16 ½˝ ² CL At least 30˝ Draw a vertical line on the wall at the center of the 30˝ wide space. Tape the Rear Wall Template onto the wall matching the centerline and touching the bottom of the cabinet. CL Draw a vertical line on the wall at the center of the 30˝ space. Tape the Rear Wall Template onto the wall matching the centerline and touching the bottom cabinet frame. Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level. Plate position – beneath recessed bottom cabinet with front overhang THE MICROWAVE MUST BE LEVEL. Draw a line on the back wall equal to the depth of the front overhang. CL 30˝ to Cooktop Use a level to make sure the cabinet bottom is level. If the cabinets have a front overhang only, with no back or side frame, install the mounting plate down the same distance as the front overhang depth. This will keep the microwave level. 30˝ to Cooktop 1. Measure the inside depth of the front overhang. 2. Draw a horizontal line on the back wall an equal distance below the cabinet bottom as the inside depth of the front overhang. 3. For this type of installation with front overhang only, align the mounting tabs with this horizontal line, not touching the cabinet bottom as described in Step D. 9 SMH8165_XAA DE68-03587A-04-EN_120725.indd 9 2012-07-25 �� 8:05:28 Step-by-step installation guide 2. D. Aligning the wall plate T fo A Hole A Draw a Vertical Line on Wall from Center of Top Cabinet Centerline notches CL Horizontal Line Area E Hole C Hole B Horizontal Line Draw a Horizontal line on wall from bottom of “Rear Wall Template˝. S CAUTION: Wear gloves to avoid cutting fingers on sharp edges. 1. Draw a Vertical line on the wall at the center of the 30˝ wide space. 2. Draw a Horizontal line on the wall at the bottom of “Rear Wall Template”. 3. Drill ⅝˝ holes for toggle bolts on 3 locations (Hole A, Hole B, Hole C) but if the location of hole is same as that of stud, drill a 3/16˝ hole for wood screw. In other words, toggle bolt can not be used to the location of stud. NOTE: Holes A, B and C are inside area E. If none of A, B and C is in a stud, find a stud somewhere in area E and draw a forth circle to line up with the stud. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Set the mounting plate aside. NOTE: DO NOT MOUNT THE PLATE AT THIS TIME. 10 SMH8165_XAA DE68-03587A-04-EN_120725.indd 10 2012-07-25 �� 8:05:29 Step-by-step installation guide 2. Ventilation types (choose a, b or c) NOTE: This microwave is shipped assembled for Outside Top Exhaust (except for non-vented models). And exhaust adaptor is shipped assembled to the filler-upper. Select the type of ventilation required for your installation and proceed to that section. This microwave oven is designed for adaptation to the following three types of ventilation: A. Outside Top Exhaust (Vertical Duct) B. Recirculating (Non-Vented Ductless) C. Outside Back Exhaust (Horizontal Duct) A. Outside top exhaust (vertical duct) B. Recirculating (non-vented ductless) Adaptor in Place for Outside Top Exhaust See page 12 See page 13 A Charcoal Filter Accessory Kit is required for the nonvented exhaust. (See your Owner’s Manual for the kit number.) C. Outside back exhaust (horizontal duct) See page 14 11 SMH8165_XAA DE68-03587A-04-EN_120725.indd 11 2012-07-25 �� 8:05:29 Step-by-step installation guide A. Outside top exhaust (vertical duct) A1. Installation procedure for exhaust adaptor and proper damper operation check B. NOTE: The house duct is needed to connect to the exhaust adaptor after installation completion. B House Duct 1. Exhaust Adaptor and Damper is shipped assembled to the filler-upper. N ne sa 1. Slide exhaust adaptor following the instructions show in diagram. 2. Make sure tape securing damper is removed and damper pivots easoly before mounting microwave. • 3 You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed. A2. Adjust the exhaust adaptor Open the top cabinet and adjust the exhaust adaptor to connect to the house duct. Blower-Plate Damper Back of Microwave C p th 4 For Front-to-Back Adjustment, Slide the Exhaust Adaptor as Needed 12 SMH8165_XAA DE68-03587A-04-EN_120725.indd 12 2012-07-25 �� 8:05:30 Step-by-step installation guide B. Recirculating (non-vented ductless) B1. Adapting microwave blower for recirculation 5. Place the blower unit back into the opening. 2. Lift up the blower plate. CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. Back of Microwave 6. 1. Remove and save screw that holds blower plate to microwave. Secure blower unit to microwave with the screw. B2. Installing the charcoal filter NOTE: The exhaust adaptor with damper is not needed for recirculating models. You may want to save them for possible future use. 3. Remove screw holds blower mortor and carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. 1. Remove screws on top of grille using a #1 Phillips screwdriver. 2. Open the door. 3. Remove the grille. • After push left, Pull the grille straight off. Charcoal Filter blower mortor screw CAUTION: Do not touch blade of blower for preventing crack and break. Hold outer case when the blower pull out or back into. 4. 4. Roll the blower unit 90 ° so that fan blade openings are facing toward the front of the microwave. Install the charcoal filter. When properly installed, the wire mesh of the filter should be visible from the front. 5. Reinstall the grille and the screws. 6. Close the door. Before Roll After Roll Insert mesh-side up Back of Microwave Back of Microwave 13 SMH8165_XAA DE68-03587A-04-EN_120725.indd 13 2012-07-25 �� 8:05:30 Step-by-step installation guide 3. C. Outside back exhaust (horizontal duct) C1. Adapting microwave blower for outside back exhaust 5. Place the blower unit back into the opening. AFTER: Fan Blade Openings Facing Back A 1. Remove and save screw that holds blower Plate to microwave. Screw 2. End A B C D End B Lift up the Blower Plate. Blower Motor IN E. Back of Microwave CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. Blower Plate Screw NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven. 3. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. 6. Close the blower plate and attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven. Push in securely until it is in the lower locking tabs. Take care to assure that the damper hinge is installed so that it is at the top and that the damper swings freely. BEFORE: Fan Blade Openings Facing Forward End B End A A Yo ou Adaptor CAUTION: Do not touch blade of blower to prevent cracking and breaking. Hold outer case when the blower is removed and re-installed. Back of Microwave Guide 4. Rotate blower unit counterclockwise 180 °. Before Rotation blower plate screw After Rotation Guide From Blower motor screw (after attached the exhaust adaptor) • Back of Microwave • Back of Microwave • C ca 14 SMH8165_XAA DE68-03587A-04-EN_120725.indd 14 2012-07-25 �� 8:05:31 e Step-by-step installation guide 3. Installation INSTALLATION OVERVIEW A. Prepare Rear Wall (only horizontal duct) B. Attach Mounting Plate to Wall C. Prepare Top Cabinet D. Mount the Microwave Oven E. Connecting Ductwork (only vertical duct) A. Preparing the rear wall for outside back exhaust B. Attach the mounting plate to the wall You need to cut an opening in the rear wall for outside exhaust. Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. 1. Remove the toggle wings from the bolts. 2. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to ¾˝ onto each bolt. CL • Read the instructions on the REAR WALL TEMPLATE. • Tape it to the rear wall. • Cut the opening, following the instructions of the REAR WALL TEMPLATE. CAUTION: Do not cut an opening on the real wall, in case of vertical duct and non-vented ductless. 15 SMH8165_XAA DE68-03587A-04-EN_120725.indd 15 2012-07-25 �� 8:05:32 Step-by-step installation guide B. ATTACH THE MOUNTING PLATE TO THE WALL (cont.) D. Mount the microwave oven D To use toggle bolts: Spacing for Toggles More Than Wall Thickness Mounting Plate Toggle Wings Toggle Bolt FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. Wall Bolt End IMPORTANT: Do not grip or use handle during installation. 3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: Before tightening toggle bolts and wood screw, make sure to coincide bottom line of the Mounting plate with Horizontal line of “Rear wall Template” and then the Mounting plate is properly centered under the cabinet. NOTE: Filler blocks are required when mounting this unit under any cabinet with a recessed bottom or front overhang. (See page 9.) CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall. IMPORTANT:The case damage that will occur from over tightening screws when filler blocks are not used is not covered under warranty. 4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts. NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord. C. Use top cabinet template for preparation of top cabinet 1. You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. 2. 3. • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on the TOP CABINET TEMPLATE. Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate. Rotate front of oven up against cabinet bottom. Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. 16 SMH8165_XAA DE68-03587A-04-EN_120725.indd 16 4 2012-07-25 �� 8:05:32 6 s Step-by-step installation guide D. MOUNT THE MICROWAVE OVEN (cont.) E. Connecting ductwork for outside top exhaust Cabinet Front House Duct Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess Self-Aligning Screw Microwave Oven Top 4. Attach the microwave oven to the top cabinet. 5. Insert the 2 self-aligning screws through the cabinet bottom shelf and filler block into the outer top cabinet of the unit. Continue to support the unit until both screws are inserted and engaged at least two full turns, then fully tighten both screws until the unit is secure. 1. Extend the house duct down to connect to the exhaust adaptor. 2. Seal exhaust duct joints using duct tape. d s 6. Install grease filters. See the Owner’s Manual packed with the microwave. y 17 SMH8165_XAA DE68-03587A-04-EN_120725.indd 17 2012-07-25 �� 8:05:32 Before You Use Your Microwave Before you use your microwave 1. Make sure the microwave oven has been installed according to instructions. 2. Remove all packing material from the microwave oven. 3. Install turntable and ring in cavity. 4. Replace house fuse or turn breaker back on. 5. Plug power cord into a dedicated 15 amp electrical outlet. 6. Read the Owner’s Manual. 7. Keep installation instructions for the local inspector’s use. Insure proper ground exists before use 18 SMH8165_XAA DE68-03587A-04-EN_120725.indd 18 2012-07-25 �� 8:05:33 Note 19 SMH8165_XAA DE68-03587A-04-EN_120725.indd 19 2012-07-25 �� 8:05:33 Code No.: DE68-03587A-04 SMH8165_XAA DE68-03587A-04-EN_120725.indd 20 2012-07-25 �� 8:05:33
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Create Date : 2012:07:25 20:05:23+09:00 Creator : Adobe InDesign CS4 (6.0) Modify Date : 2013:03:18 19:00:10+09:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2013:03:18 19:00:10+09:00 Creator Tool : Adobe InDesign CS4 (6.0) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 10758 bytes, use -b option to extract) Instance ID : uuid:f74dd86c-e7c4-4006-bc1f-3362f12f0f11 Document ID : xmp.did:044A9CC6B47EE111A025D31A6E1D5B26 Original Document ID : adobe:docid:indd:d08821f6-c595-11dd-8bb2-e7b39da9853f Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:034A9CC6B47EE111A025D31A6E1D5B26 Derived From Document ID : xmp.did:D679388C207DE0119B56E8DF04CFB0E5 Derived From Original Document ID: adobe:docid:indd:d08821f6-c595-11dd-8bb2-e7b39da9853f Derived From Rendition Class : default History Action : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:4C05E06C5675E0119E56CAC70E7E7654, xmp.iid:4D05E06C5675E0119E56CAC70E7E7654, xmp.iid:4E05E06C5675E0119E56CAC70E7E7654, xmp.iid:4F05E06C5675E0119E56CAC70E7E7654, xmp.iid:B587835F807BE011AB9EF64DB23210E4, xmp.iid:B687835F807BE011AB9EF64DB23210E4, xmp.iid:B787835F807BE011AB9EF64DB23210E4, xmp.iid:B887835F807BE011AB9EF64DB23210E4, xmp.iid:B987835F807BE011AB9EF64DB23210E4, xmp.iid:BA87835F807BE011AB9EF64DB23210E4, xmp.iid:BB87835F807BE011AB9EF64DB23210E4, xmp.iid:BD87835F807BE011AB9EF64DB23210E4, xmp.iid:CC53733F937BE011AB9EF64DB23210E4, xmp.iid:CD53733F937BE011AB9EF64DB23210E4, xmp.iid:CE53733F937BE011AB9EF64DB23210E4, xmp.iid:CF53733F937BE011AB9EF64DB23210E4, xmp.iid:D053733F937BE011AB9EF64DB23210E4, xmp.iid:D153733F937BE011AB9EF64DB23210E4, xmp.iid:D253733F937BE011AB9EF64DB23210E4, xmp.iid:D353733F937BE011AB9EF64DB23210E4, xmp.iid:D453733F937BE011AB9EF64DB23210E4, xmp.iid:D553733F937BE011AB9EF64DB23210E4, xmp.iid:D653733F937BE011AB9EF64DB23210E4, xmp.iid:3C9D7B979D7BE011AB9EF64DB23210E4, xmp.iid:3D9D7B979D7BE011AB9EF64DB23210E4, xmp.iid:3F9D7B979D7BE011AB9EF64DB23210E4, xmp.iid:409D7B979D7BE011AB9EF64DB23210E4, xmp.iid:419D7B979D7BE011AB9EF64DB23210E4, xmp.iid:429D7B979D7BE011AB9EF64DB23210E4, xmp.iid:439D7B979D7BE011AB9EF64DB23210E4, xmp.iid:449D7B979D7BE011AB9EF64DB23210E4, xmp.iid:459D7B979D7BE011AB9EF64DB23210E4, xmp.iid:469D7B979D7BE011AB9EF64DB23210E4, xmp.iid:4BF4F11DA27BE011AB9EF64DB23210E4, xmp.iid:4CF4F11DA27BE011AB9EF64DB23210E4, xmp.iid:4DF4F11DA27BE011AB9EF64DB23210E4, xmp.iid:0721654FB57BE011BBCB8057C4CC54CD, xmp.iid:0821654FB57BE011BBCB8057C4CC54CD, xmp.iid:2945D6C4367CE011A650CE99BCACFFC4, xmp.iid:2A45D6C4367CE011A650CE99BCACFFC4, xmp.iid:2B45D6C4367CE011A650CE99BCACFFC4, xmp.iid:2C45D6C4367CE011A650CE99BCACFFC4, xmp.iid:670EA62E417CE011A650CE99BCACFFC4, xmp.iid:680EA62E417CE011A650CE99BCACFFC4, xmp.iid:690EA62E417CE011A650CE99BCACFFC4, xmp.iid:6A0EA62E417CE011A650CE99BCACFFC4, xmp.iid:6B0EA62E417CE011A650CE99BCACFFC4, xmp.iid:6C0EA62E417CE011A650CE99BCACFFC4, xmp.iid:6D0EA62E417CE011A650CE99BCACFFC4, xmp.iid:6E0EA62E417CE011A650CE99BCACFFC4, xmp.iid:6F0EA62E417CE011A650CE99BCACFFC4, xmp.iid:700EA62E417CE011A650CE99BCACFFC4, xmp.iid:710EA62E417CE011A650CE99BCACFFC4, xmp.iid:D1351C93487CE011A650CE99BCACFFC4, xmp.iid:D2351C93487CE011A650CE99BCACFFC4, xmp.iid:D3351C93487CE011A650CE99BCACFFC4, xmp.iid:D4351C93487CE011A650CE99BCACFFC4, xmp.iid:D5351C93487CE011A650CE99BCACFFC4, xmp.iid:D6351C93487CE011A650CE99BCACFFC4, xmp.iid:D7351C93487CE011A650CE99BCACFFC4, xmp.iid:D8351C93487CE011A650CE99BCACFFC4, xmp.iid:D9351C93487CE011A650CE99BCACFFC4, xmp.iid:DA351C93487CE011A650CE99BCACFFC4, xmp.iid:DB351C93487CE011A650CE99BCACFFC4, xmp.iid:8F1AE0835C7CE011A650CE99BCACFFC4, xmp.iid:901AE0835C7CE011A650CE99BCACFFC4, xmp.iid:911AE0835C7CE011A650CE99BCACFFC4, xmp.iid:921AE0835C7CE011A650CE99BCACFFC4, xmp.iid:931AE0835C7CE011A650CE99BCACFFC4, xmp.iid:D93B6AB5637CE0118710C78DBFD782C9, xmp.iid:DA3B6AB5637CE0118710C78DBFD782C9, xmp.iid:DB3B6AB5637CE0118710C78DBFD782C9, xmp.iid:DC3B6AB5637CE0118710C78DBFD782C9, xmp.iid:DD3B6AB5637CE0118710C78DBFD782C9, xmp.iid:C5F27967687CE01198E1C194A482CE59, xmp.iid:C6F27967687CE01198E1C194A482CE59, xmp.iid:C7F27967687CE01198E1C194A482CE59, xmp.iid:C8F27967687CE01198E1C194A482CE59, xmp.iid:673C91117C7CE011901A9BC4B4990D6C, xmp.iid:693C91117C7CE011901A9BC4B4990D6C, xmp.iid:6A3C91117C7CE011901A9BC4B4990D6C, xmp.iid:6B3C91117C7CE011901A9BC4B4990D6C, xmp.iid:6C3C91117C7CE011901A9BC4B4990D6C, xmp.iid:E58D06EC027DE0119B56E8DF04CFB0E5, xmp.iid:E68D06EC027DE0119B56E8DF04CFB0E5, xmp.iid:E78D06EC027DE0119B56E8DF04CFB0E5, xmp.iid:E88D06EC027DE0119B56E8DF04CFB0E5, xmp.iid:E98D06EC027DE0119B56E8DF04CFB0E5, xmp.iid:EA8D06EC027DE0119B56E8DF04CFB0E5, xmp.iid:EB8D06EC027DE0119B56E8DF04CFB0E5, xmp.iid:EC8D06EC027DE0119B56E8DF04CFB0E5, xmp.iid:ED8D06EC027DE0119B56E8DF04CFB0E5, xmp.iid:EE8D06EC027DE0119B56E8DF04CFB0E5, xmp.iid:24B05F0B067DE0119B56E8DF04CFB0E5, xmp.iid:25B05F0B067DE0119B56E8DF04CFB0E5, xmp.iid:26B05F0B067DE0119B56E8DF04CFB0E5, xmp.iid:27B05F0B067DE0119B56E8DF04CFB0E5, xmp.iid:28B05F0B067DE0119B56E8DF04CFB0E5, xmp.iid:29B05F0B067DE0119B56E8DF04CFB0E5, xmp.iid:2BB05F0B067DE0119B56E8DF04CFB0E5, xmp.iid:2CB05F0B067DE0119B56E8DF04CFB0E5, xmp.iid:2DB05F0B067DE0119B56E8DF04CFB0E5, xmp.iid:2EB05F0B067DE0119B56E8DF04CFB0E5, xmp.iid:F2983020157DE0119B56E8DF04CFB0E5, xmp.iid:F3983020157DE0119B56E8DF04CFB0E5, xmp.iid:F4983020157DE0119B56E8DF04CFB0E5, xmp.iid:F5983020157DE0119B56E8DF04CFB0E5, xmp.iid:F6983020157DE0119B56E8DF04CFB0E5, xmp.iid:F7983020157DE0119B56E8DF04CFB0E5, xmp.iid:F8983020157DE0119B56E8DF04CFB0E5, xmp.iid:F9983020157DE0119B56E8DF04CFB0E5, xmp.iid:FA983020157DE0119B56E8DF04CFB0E5, xmp.iid:FB983020157DE0119B56E8DF04CFB0E5, xmp.iid:FC983020157DE0119B56E8DF04CFB0E5, xmp.iid:D379388C207DE0119B56E8DF04CFB0E5, xmp.iid:D479388C207DE0119B56E8DF04CFB0E5, xmp.iid:D579388C207DE0119B56E8DF04CFB0E5, xmp.iid:D679388C207DE0119B56E8DF04CFB0E5, xmp.iid:B3C2AB71367DE0119A1EFEF30B54E2C4, xmp.iid:B4C2AB71367DE0119A1EFEF30B54E2C4, xmp.iid:B5C2AB71367DE0119A1EFEF30B54E2C4, xmp.iid:B6C2AB71367DE0119A1EFEF30B54E2C4, xmp.iid:B7C2AB71367DE0119A1EFEF30B54E2C4, xmp.iid:B8C2AB71367DE0119A1EFEF30B54E2C4, xmp.iid:B9C2AB71367DE0119A1EFEF30B54E2C4, xmp.iid:BAC2AB71367DE0119A1EFEF30B54E2C4, xmp.iid:BBC2AB71367DE0119A1EFEF30B54E2C4, xmp.iid:BCC2AB71367DE0119A1EFEF30B54E2C4, xmp.iid:BDC2AB71367DE0119A1EFEF30B54E2C4, xmp.iid:E79C0D163E7DE0119A1EFEF30B54E2C4, xmp.iid:E89C0D163E7DE0119A1EFEF30B54E2C4, xmp.iid:77ABCC88A940E11191CFEDFA1228D17E, xmp.iid:F41123AC2A7EE1119712F6A3C71EF2C6, xmp.iid:F51123AC2A7EE1119712F6A3C71EF2C6, xmp.iid:C526FF6B327EE1119E829547E08D1B5B, xmp.iid:C726FF6B327EE1119E829547E08D1B5B, xmp.iid:C826FF6B327EE1119E829547E08D1B5B, xmp.iid:C926FF6B327EE1119E829547E08D1B5B, xmp.iid:CA26FF6B327EE1119E829547E08D1B5B, xmp.iid:CC26FF6B327EE1119E829547E08D1B5B, xmp.iid:CD26FF6B327EE1119E829547E08D1B5B, xmp.iid:CE26FF6B327EE1119E829547E08D1B5B, xmp.iid:3AE898E3447EE1119E829547E08D1B5B, xmp.iid:3CE898E3447EE1119E829547E08D1B5B, xmp.iid:3DE898E3447EE1119E829547E08D1B5B, xmp.iid:3EE898E3447EE1119E829547E08D1B5B, xmp.iid:3FE898E3447EE1119E829547E08D1B5B, xmp.iid:40E898E3447EE1119E829547E08D1B5B, xmp.iid:2686FF1A567EE1119E829547E08D1B5B, xmp.iid:2786FF1A567EE1119E829547E08D1B5B, xmp.iid:2886FF1A567EE1119E829547E08D1B5B, xmp.iid:2986FF1A567EE1119E829547E08D1B5B, xmp.iid:024A9CC6B47EE111A025D31A6E1D5B26, xmp.iid:034A9CC6B47EE111A025D31A6E1D5B26, xmp.iid:044A9CC6B47EE111A025D31A6E1D5B26, xmp.iid:97CC89BCB77EE111B54BC028180C852A, xmp.iid:94AA8F35C07EE111B54BC028180C852A, xmp.iid:F7DCF1FD6F80E111A38DEA50A5A7A7F4, xmp.iid:FEDCF1FD6F80E111A38DEA50A5A7A7F4, xmp.iid:FFDCF1FD6F80E111A38DEA50A5A7A7F4, xmp.iid:271BEBDF7280E111A38DEA50A5A7A7F4, xmp.iid:2B1BEBDF7280E111A38DEA50A5A7A7F4, xmp.iid:2E1BEBDF7280E111A38DEA50A5A7A7F4, xmp.iid:2F1BEBDF7280E111A38DEA50A5A7A7F4, xmp.iid:301BEBDF7280E111A38DEA50A5A7A7F4, xmp.iid:563B7EDC7680E111A38DEA50A5A7A7F4, xmp.iid:209914B3E881E111ADF7FB3E42B991B0, xmp.iid:858196E35E82E111A7D0E4D6C41F7CC7, xmp.iid:868196E35E82E111A7D0E4D6C41F7CC7, xmp.iid:888196E35E82E111A7D0E4D6C41F7CC7, xmp.iid:898196E35E82E111A7D0E4D6C41F7CC7, xmp.iid:8A8196E35E82E111A7D0E4D6C41F7CC7, xmp.iid:8B8196E35E82E111A7D0E4D6C41F7CC7, xmp.iid:8C8196E35E82E111A7D0E4D6C41F7CC7, xmp.iid:8D8196E35E82E111A7D0E4D6C41F7CC7, xmp.iid:8E8196E35E82E111A7D0E4D6C41F7CC7, xmp.iid:72826DBF5F82E111A7D0E4D6C41F7CC7, xmp.iid:751594DDA182E111B9628C606A55137E, xmp.iid:761594DDA182E111B9628C606A55137E, xmp.iid:771594DDA182E111B9628C606A55137E, xmp.iid:781594DDA182E111B9628C606A55137E, xmp.iid:791594DDA182E111B9628C606A55137E, xmp.iid:EB84D282AD82E111B9628C606A55137E, xmp.iid:1D6583CFAD82E111B9628C606A55137E, xmp.iid:246583CFAD82E111B9628C606A55137E, xmp.iid:49AF4D64D582E111B9628C606A55137E, xmp.iid:4AAF4D64D582E111B9628C606A55137E, xmp.iid:4BAF4D64D582E111B9628C606A55137E, xmp.iid:4CAF4D64D582E111B9628C606A55137E, xmp.iid:4DAF4D64D582E111B9628C606A55137E, xmp.iid:BAEC2626D782E111B9628C606A55137E, xmp.iid:E3820CF4DA82E111B9628C606A55137E, xmp.iid:915B19B4E589E1119796AABEEC048FBE, xmp.iid:7903D0B7EA89E1119796AABEEC048FBE, xmp.iid:400F8087FCCEE111B1C6FEA1961DC3FB, xmp.iid:410F8087FCCEE111B1C6FEA1961DC3FB, xmp.iid:052E917405CFE111A68AB8DC81631B8A, xmp.iid:062E917405CFE111A68AB8DC81631B8A, xmp.iid:38E5BD0148D6E111AD3ADFBBEBA2255B History When : 2011:05:03 18:59:16+09:00, 2011:05:03 18:59:16+09:00, 2011:05:03 19:13:57+09:00, 2011:05:03 19:20:54+09:00, 2011:05:11 13:01:29+09:00, 2011:05:11 13:01:47+09:00, 2011:05:11 13:02:08+09:00, 2011:05:11 13:03:47+09:00, 2011:05:11 13:05:27+09:00, 2011:05:11 13:06:34+09:00, 2011:05:11 13:07:03+09:00, 2011:05:11 14:53:26+09:00, 2011:05:11 14:55:17+09:00, 2011:05:11 14:57:21+09:00, 2011:05:11 15:12:44+09:00, 2011:05:11 15:19:23+09:00, 2011:05:11 15:21:07+09:00, 2011:05:11 15:35:25+09:00, 2011:05:11 15:43:16+09:00, 2011:05:11 15:51:56+09:00, 2011:05:11 15:52:12+09:00, 2011:05:11 16:01:25+09:00, 2011:05:11 16:05:54+09:00, 2011:05:11 16:09:20+09:00, 2011:05:11 16:09:47+09:00, 2011:05:11 16:16:12+09:00, 2011:05:11 16:16:52+09:00, 2011:05:11 16:19:42+09:00, 2011:05:11 16:29:42+09:00, 2011:05:11 16:30:03+09:00, 2011:05:11 16:30:50+09:00, 2011:05:11 16:37:17+09:00, 2011:05:11 16:40:06+09:00, 2011:05:11 16:41:43+09:00, 2011:05:11 16:41:50+09:00, 2011:05:11 16:42:19+09:00, 2011:05:11 18:59:07+09:00, 2011:05:11 19:01:23+09:00, 2011:05:12 10:54:34+09:00, 2011:05:12 11:01:48+09:00, 2011:05:12 11:02:52+09:00, 2011:05:12 11:17:49+09:00, 2011:05:12 11:40:21+09:00, 2011:05:12 11:43:34+09:00, 2011:05:12 11:44:06+09:00, 2011:05:12 11:44:43+09:00, 2011:05:12 12:05:37+09:00, 2011:05:12 12:06:29+09:00, 2011:05:12 12:10:56+09:00, 2011:05:12 12:14:51+09:00, 2011:05:12 12:14:58+09:00, 2011:05:12 12:15:45+09:00, 2011:05:12 12:32:53+09:00, 2011:05:12 12:33:16+09:00, 2011:05:12 13:36:35+09:00, 2011:05:12 13:39:43+09:00, 2011:05:12 13:40:12+09:00, 2011:05:12 13:58:24+09:00, 2011:05:12 13:58:48+09:00, 2011:05:12 13:59:57+09:00, 2011:05:12 14:11:16+09:00, 2011:05:12 14:18:53+09:00, 2011:05:12 14:20:42+09:00, 2011:05:12 14:37:13+09:00, 2011:05:12 14:56:01+09:00, 2011:05:12 14:57:51+09:00, 2011:05:12 15:06:01+09:00, 2011:05:12 15:45:11+09:00, 2011:05:12 15:45:21+09:00, 2011:05:12 15:47:30+09:00, 2011:05:12 15:51:59+09:00, 2011:05:12 16:01:33+09:00, 2011:05:12 16:10:18+09:00, 2011:05:12 16:16:58+09:00, 2011:05:12 16:21:07+09:00, 2011:05:12 16:24:36+09:00, 2011:05:12 16:28:55+09:00, 2011:05:12 16:30:09+09:00, 2011:05:12 18:41:53+09:00, 2011:05:12 18:47:04+09:00, 2011:05:12 19:06:15+09:00, 2011:05:12 19:06:28+09:00, 2011:05:12 19:06:49+09:00, 2011:05:13 10:47:12+09:00, 2011:05:13 10:47:56+09:00, 2011:05:13 10:50:38+09:00, 2011:05:13 10:56:19+09:00, 2011:05:13 10:57:45+09:00, 2011:05:13 10:57:54+09:00, 2011:05:13 10:59:21+09:00, 2011:05:13 10:59:52+09:00, 2011:05:13 11:01:29+09:00, 2011:05:13 11:05:52+09:00, 2011:05:13 11:09:33+09:00, 2011:05:13 11:15:50+09:00, 2011:05:13 11:16:09+09:00, 2011:05:13 11:18:45+09:00, 2011:05:13 11:48:08+09:00, 2011:05:13 11:51:02+09:00, 2011:05:13 12:38:40+09:00, 2011:05:13 12:52:51+09:00, 2011:05:13 12:55:23+09:00, 2011:05:13 12:56:41+09:00, 2011:05:13 12:57:30+09:00, 2011:05:13 13:13:58+09:00, 2011:05:13 13:15:41+09:00, 2011:05:13 13:16:33+09:00, 2011:05:13 13:17:22+09:00, 2011:05:13 13:17:45+09:00, 2011:05:13 13:23:15+09:00, 2011:05:13 13:28:58+09:00, 2011:05:13 13:30:55+09:00, 2011:05:13 13:32:29+09:00, 2011:05:13 13:32:39+09:00, 2011:05:13 14:19:16+09:00, 2011:05:13 14:20:46+09:00, 2011:05:13 14:20:59+09:00, 2011:05:13 14:20:59+09:00, 2011:05:13 16:56+09:00, 2011:05:13 16:56:44+09:00, 2011:05:13 17:07:53+09:00, 2011:05:13 17:16:08+09:00, 2011:05:13 17:18:56+09:00, 2011:05:13 17:19:11+09:00, 2011:05:13 17:25:46+09:00, 2011:05:13 17:28:18+09:00, 2011:05:13 17:30:33+09:00, 2011:05:13 17:30:43+09:00, 2011:05:13 17:43:59+09:00, 2011:05:13 17:50:43+09:00, 2011:05:13 17:51:52+09:00, 2012:01:17 11:55:55+09:00, 2012:04:04 17:23:54+09:00, 2012:04:04 17:25:39+09:00, 2012:04:04 17:44:42+09:00, 2012:04:04 18:22:28+09:00, 2012:04:04 18:24:03+09:00, 2012:04:04 18:29:39+09:00, 2012:04:04 18:29:50+09:00, 2012:04:04 19:40:28+09:00, 2012:04:04 19:41:30+09:00, 2012:04:04 19:41:51+09:00, 2012:04:04 20:08:21+09:00, 2012:04:04 20:18:31+09:00, 2012:04:04 20:30:28+09:00, 2012:04:04 20:30:41+09:00, 2012:04:04 20:32:15+09:00, 2012:04:04 21:04:30+09:00, 2012:04:04 22:00:08+09:00, 2012:04:04 22:02:04+09:00, 2012:04:04 22:05:41+09:00, 2012:04:04 22:07:34+09:00, 2012:04:05 09:17:48+09:00, 2012:04:05 09:18:08+09:00, 2012:04:05 09:18:08+09:00, 2012:04:05 10:01:15+09:00, 2012:04:05 10:51:04+09:00, 2012:04:07 14:16+09:00, 2012:04:07 14:28:15+09:00, 2012:04:07 14:28:26+09:00, 2012:04:07 14:31:06+09:00, 2012:04:07 14:37:09+09:00, 2012:04:07 14:38:55+09:00, 2012:04:07 14:39:48+09:00, 2012:04:07 14:40:07+09:00, 2012:04:07 15:25:27+09:00, 2012:04:09 11:13:26+09:00, 2012:04:10 01:13:50+09:00, 2012:04:10 01:14:18+09:00, 2012:04:10 01:14:48+09:00, 2012:04:10 01:15:11+09:00, 2012:04:10 01:15:45+09:00, 2012:04:10 01:16:59+09:00, 2012:04:10 01:17:20+09:00, 2012:04:10 01:18:37+09:00, 2012:04:10 01:18:49+09:00, 2012:04:10 01:19:14+09:00, 2012:04:10 10:14:08+09:00, 2012:04:10 10:15:38+09:00, 2012:04:10 10:20:32+09:00, 2012:04:10 10:23:01+09:00, 2012:04:10 10:23:53+09:00, 2012:04:10 10:37:36+09:00, 2012:04:10 10:38:02+09:00, 2012:04:10 10:48:59+09:00, 2012:04:10 15:30:39+09:00, 2012:04:10 15:31:40+09:00, 2012:04:10 15:32:13+09:00, 2012:04:10 15:32:19+09:00, 2012:04:10 15:33:34+09:00, 2012:04:10 15:33:56+09:00, 2012:04:10 16:07:39+09:00, 2012:04:19 15:39:10+09:00, 2012:04:19 15:46:27+09:00, 2012:07:16 13:12:59+09:00, 2012:07:16 13:13:28+09:00, 2012:07:16 14:18:30+09:00, 2012:07:16 14:19:01+09:00, 2012:07:25 20:04:44+09:00 History Software Agent : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0 History Changed : /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, / Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : xmp.iid:70767EB3397EE1118D4EFB5FF5A80D0D, xmp.iid:71767EB3397EE1118D4EFB5FF5A80D0D, xmp.iid:72767EB3397EE1118D4EFB5FF5A80D0D, uuid:FB1B0749132CDF1182F4A9198C899173, uuid:0B43C3CC4B14DF11B169D93593F8610F, uuid:0B43C3CC4B14DF11B169D93593F8610F, xmp.iid:A687F00B0B7DE01186DD91E5E16273B2, uuid:D3B02B74E812DF11A89BDB0F0D9FDF74, xmp.iid:769F38EE0C7DE0118D7AF167A636A006, uuid:5405485c-81d6-42e2-b5d4-5a66c96ffd05 Manifest Reference Document ID : xmp.did:70767EB3397EE1118D4EFB5FF5A80D0D, xmp.did:71767EB3397EE1118D4EFB5FF5A80D0D, xmp.did:72767EB3397EE1118D4EFB5FF5A80D0D, uuid:F81B0749132CDF1182F4A9198C899173, uuid:0643C3CC4B14DF11B169D93593F8610F, uuid:0643C3CC4B14DF11B169D93593F8610F, xmp.did:A687F00B0B7DE01186DD91E5E16273B2, uuid:D2B02B74E812DF11A89BDB0F0D9FDF74, xmp.did:769F38EE0C7DE0118D7AF167A636A006, uuid:e2bc8769-1ac1-495e-8090-d6e3d5a82e9b Doc Change Count : 7782 Format : application/pdf Producer : Adobe PDF Library 9.0 Trapped : False Page Count : 20EXIF Metadata provided by EXIF.tools