Sargent Instructions For Installing 1431 Series Door Closers (with Hold Open Arms 'H'/UH/HZ/HZA/PH9) A7140F Low Res

User Manual: Sargent Instructions for installing 1431 Series Door Closers (with Hold Open Arms 'H'/UH/HZ/HZA/PH9) Instruction Sheets

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

INSTRUCTIONS FOR
1431 Door Closer with Hold Open Arms
1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6
FOR INSTALLATION ASSISTANCE CALL SARGENT AT 1-800-727-5477 / www.sargentlock.com

Installation Instructions based on Application and Arm type
Standard Mounting Application H arm

For Standard Application - the Door Closer is mounted
on the hinge side of door (see page 2)

Parallel Arm Application PH9 Arm
For Parallel Arm Application - the Door Closer is mounted
on the stop side of door (see page 4)

Top Jamb Application H, HZ & HZA Arm
For Top Jamb Application - the Door Closer is mounted on the
frame on the stop side of the door (see page 6)

+
or

LEFT
HAND DOOR

RIGHT
HAND DOOR
HINGE SIDE
STOP SIDE

IMPORTANT NOTICE
PRE-DRILL 3/32” HOLES FOR SELF-TAPPING SCREWS
OR TAP #12-24 FOR MACHINE SCREWS

HINGE SIDE
STOP SIDE

Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission
of Sargent Manufacturing Company is prohibited.

A7140F

STANDARD APPLICATION

A
B

A1) Select closer mounting position based on the maximum door opening, as listed below
Note: For ADA applications, select the 160ϒ position
MAXIMUM DOOR
OPENING

B1) Prep door and frame
Note: 3/32" pilot holes are required when Self Tapping Screws are being used
Note: If machine screws are being used, use a drill #16 (.177) and a #12-24 tap
B2) Install closer body onto the door
B3) Install Foot & Rod Assembly onto the frames
DIM. “B”
DIM. “A”

2-1/2"

#12 X 1 1/2 SCREWS OR
#12-24 X 5/8 FLAT HEAD
MACHINE SCREW*

11⁄4"

DIM. A

DIM. B

120ϒ

7 1/2"

13 1/4"

160ϒ**

4 1/4"

10"

**If Butt, Frame and Wall Conditions Permit
Door Will Open 180ϒ

TOP OF DOOR

FRAME

7⁄ 8 "

2 5⁄8" MIN
TOP RAIL

2 9⁄16"

DOOR CLOSER

RAILS TO 1 3⁄4" MAY BE
USED PROVIDED FRAME
DOES NOT PROJECT
BEYOND FACE OF DOOR

111⁄8"

CL OF HINGE PIVOT

FACE OF DOOR

DOOR

2 5⁄16"

RIGHT HAND DOOR ILLUSTRATED. SAME DIMENSIONS APPLY FOR LEFT HAND DOOR.
*SEE PAGE 8 FOR MORTISE NUTS

C1) Install main arm on the closer with the index mark on the spindle aligning with the # 2 on the main arm (as shown)

RIGHT HAND DOOR
4

INDEX MARK
ON SPINDLE

MAIN
ARM
POSITION OF
MAIN ARM WHEN
ASSEMBLING
TO SPINDLE

Attach hold open foot to frame with adjusting nut facing down for left hand door or up for right hand door, as illustrated below
NUT FACES UP

FRAME

NUT FACES DOWN
RIGHT HAND
DOOR SHOWN

A7140F

LEFT HAND
DOOR SHOWN

STANDARD APPLICATION
E1) Opening the door slightly, slide rod into swivel arm and then close the door
E2) With the door closed, position the swivel arm so that it is 90º to the door surface
E3) Tighten the arm screw securely
RIGHT HAND DOOR

INDEX MARK
ON SPINDLE

MAIN
ARM

POSITION OF MAIN
ARM WHEN ASSEMBLING
TO SPINDLE

ARM
SCREW

90ϒ

HOLD
OPEN ARM
ROD

Adjust closer as required (See page 8 for details).

ACCESSORIES INFORMATION
H8 MORTISE FOOT
FOR USE WHERE THE
STANDARD SURFACE
APPLIED FOOT CANNOT
BE ATTACHED TO THE
TOP CASING OR WHERE
APPEARANCE IS A
MAJOR FACTOR

1430-J COVER PLATE
MAY BE USED WHEN CLOSER IS MOUNTED
ON A NARROW RAIL TO IMPROVE APPEARANCE
WHEN CLOSER IS VIEWED THRU GLASS

1431-W corner bracket closer is mounted on bracket which is attached to door jamb
on stop side of door
Use this application for exterior doors to keep the closer inside of building; Also may be
used to obtain full 180ϒ door opening

MORTISE NUTS FOR BOLTING THRU THE DOOR ARE FURNISHED WHEN ORDERED

A7140F

MAXIMUM DOOR
OPENING

A7140F

INSTRUCTIONS FOR INSTALLING PARALLEL ARM APPLICATION

CLOSER MOUNTED ON
STOP SIDE OF DOOR

Select degree of door opening required and attach door closer body to door (long end toward hinge) and foot bracket to frame (according to
illustration on “A” page 3). Use templates enclosed for special arms.
Mount hold open arm to bracket with adjusting screw facing down for left hand door, facing up for right hand door.
NUT FACES UP
LEFT HAND
DOOR SHOWN

RIGHT HAND
DOOR SHOWN
NUT FACES DOWN

D1) Install main arm on the closer with the index mark on
spindle aligned with the number on the arm
Note: Left Hand Doors -align index mark with the # 4
on the main arm (as shown)
Note: Right Hand Doors -align index mark with the # 5
on the main arm (as shown)
D2) This requires the spindle to be rotated
D3) Rotate the spindle on the bottom of the closer to align
index mark with the required number on the arm
INDEX MARK
ON SPINDLE

MAIN
ARM

ROD

FOOT BRACKET

45°

HOLD
OPEN ARM

Right Hand Door

Left Hand Door

LEFT HAND DOOR

INDEX MARK
ON SPINDLE

45°

PRELOAD 45°

ARM
SCREW

E1) Opening the door slightly, slide rod into swivel arm and
then close the door.
E2) With the door in the closed position, swivel the arm so that
the pivot is an 1-1/2" off the door surface (as shown below)
E3) Tighten the arm screw securely

PRELOAD 45°

LEFT HAND DOOR
1-1/2"
ROD

FOOT BRACKET
HOLD
OPEN ARM

ARM
SCREW

Adjust closer as required. See page 8 for details.

ACCESSORIES INFORMATION

#H8 MORTISE FOOT
2 1/2" MIN.

1430-D DROP BRACKET
CLOSER IS MOUNTED ON PLATE WHEN
TOP RAIL IS TOO NARROW

1430-J COVER PLATE
May be used when closer is mounted on
a narrow rail to improve appearance when
closer is viewed through glass

#8 MORTISE FOOT
For use where the
standard surface applied
foot cannot be attached
to the top casing or where
appearance is a major
factor

MORTISE NUTS FOR BOLTING THRU THE DOOR
ARE FURNISHED WHEN ORDERED
Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission
of Sargent Manufacturing Company is prohibited.

A7140F

TOP JAM APPLICATION
INSTALLATION
INSTRUCTIONS

CLOSER MOUNTED ON FRAME
ABOVE STOP SIDE OF A DOOR

LEFT HAND DOOR ILLUSTRATED
SAME DIMENSIONS APPLY FOR RIGHT HAND
DOOR MEASURE FROM HINGE CL

HINGE SIDE

STOP SIDE

#2 x 1-1/2" WOOD SCREWS
OR #12-24 x 5/8" FLAT
HEAD MACHINE SCREWS

3-3/8"
DOOR CLOSER

5/8"

HINGE SIDE

STOP SIDE

THIS IS A LEFT HAND DOOR
THIS IS A RIGHT HAND DOOR
CLOSERS ARE NON-HANDED

TOP OF DOOR

1"
DIM "A"

2-1/4"

2-1/2"
11-1/8"

CL OF CLOSER
MOUNTING
SCREWS

CLOSER FOOT
APPLIED TO
DOOR

2-9/16"

CL OF HINGE PIVOT

DOOR
DEPTH OF REVEAL

ARM ASSEMBLY
TYPE

REVEAL DEPTH

DIM. A

MAX DOOR
OPENING

RANGE OF HOLD
OPEN

“H” ARM

0" TO 2"

5-3/4"

180°

80° - 180°

“HZ” ARM

2-1/8" TO 5"

6-1/2"

140°

80° - 140°

“HZA” ARM

5-1/8" TO 8"

7-1/4"

140°

80° - 130°

SPRING ADJUSTMENT

CW-CLOCKWISE

ADJUST SPRING POWER ACCORDING TO CHART.

CCW-COUNTER CLOCKWISE

NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT*
USE CHART AS GUIDE ONLY.

SPRING POWER
ADJUSTING NUT

DECREASE
POWER

–

INCREASE
POWER

DOOR
WIDTH
(INCHES)

APPROXIMATE
DOOR WEIGHT
(POUNDS)

1430 DOOR
CLOSERS

24
30
32
36
40
42
44
46
48
OVER 48

80
110
115
130
150
155
165
170
180

1-3 CCW
FACTORY**
SET

A7140F

FACTORY**
SET
4-7 CW

1-3 CW

7-10 CW

4-7 CW
7-10 CW

* FOR EXTERIOR DOORS USE 1430 CLOSERS ONLY.
** CLOSERS ARE FACTORY SET FOR INTERIOR DOORS.

FOR EXTERIOR DOORS AND WHERE STRONG DRAFT EXISTS INCREASE SPRING POWER AS NEEDED BY TURNING SPRING
ADJUSTING NUT CLOCKWISE. IF NECESSARY, DECREASE SPRING POWER TO MEET REQUIREMENTS BY TURNING SPRING
ADJUSTING NUT COUNTER CLOCKWISE.

1431*
DOOR
CLOSERS

INSTRUCTIONS FOR INSTALLING TOP JAMB
D1) Install main arm on the closer with the index mark on spindle aligned with the number on the arm
Note: Left Hand Doors -align index mark with the # 3 on the main arm (as shown)
Note: Right Hand Doors -align index mark with the # 1 on the main arm (as shown)
LEFT HAND DOOR

LEFT HAND

RIGHT HAND

INDEX MARK
ON SPINDLE

45°

MAIN
ARM

MAIN
ARM
POSITION
OF MAIN ARM
WHEN
ASSEMBLING
TO SPINDLE

45°

INDEX MARK
ON SPINDLE

CLOSER MOUNTED ON FRAME
ABOVE STOP SIDE OF DOOR

Attach hold open foot to frame with adjusting nut facing down for left hand door or up for right hand door as illustrated below.

NUT FACES UP

FRAME

NUT FACES DOWN

RIGHT HAND
DOOR SHOWN

LEFT HAND
DOOR SHOWN

F1) Opening the door slightly, slide rod into swivel
arm and then close the door
F2) With the door closed, position the main arm so
it is at 90º to the door surface
F3) Tighten the arm screw securely

LEFT HAND DOOR

RIGHT
ANGLE

ARM
SCREW

POSITION OF
MAIN ARM WHEN
ASSEMBLING
TO SPINDLE

HOLD
OPEN ARM
ROD

Adjust closer as required. See page 8 for details.

A7140F

FINAL ADJUSTMENT AND REGULATING PROCEDURE
Minimum recommended door closing time is 6 Seconds for
doors opened to 90 degrees.
Use 1/8” hex (Allen) wrench to adjust valves as needed.
Closing and latching speeds:
Turn valves clockwise to slow down or counterclockwise to
speed up door movement.
Backcheck:
To regulate the intensity of back check action, turn valve clockwise
to increase or counterclockwise to decrease checking.
CAUTION: Set valve for slight cushioning effect; closer can be
damaged if the checking action is too abrupt. Never use
the backcheck as a door stop. Always use a door stop to stop
the door.
Delayed action feature (Optional feature on some models):
“Delayed action” provides slow door closing through the
delayed action range. Turn valve clockwise to slow down or
counterclockwise to speed up door movement.
NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT

DOOR WIDTH
(INCHES)

24-30
30-36

1431 DOOR CLOSER

TURN nut 1-3
FACTORY SET

36-42

TURN nut 1-4

42-48

TURN nut 7-9

Adjusting door
to close due to
high draft
conditions may
exceed ADA
standards.
Consult local
ordinances
when fire doors
are involved

Adjustment hold open arm
Slight tightening or loosening of hold
open nut changes holding position of door.

FRAME

Note: To protect wall, trim and closer, use a door stop
located 10° beyond hold open position but not beyond
the max. door opening shown on instructions.

HOLD
OPEN
NUT

USE 15/16"
WRENCH TO
ADJUST NUT

DOOR
STOP

COVER

MORTISE
NUT HEAD

UNREINFORCED
DOOR

DRILL 1/4" DIA.
HOLE FOR MOUNTING SCREWS

INSTALL COVER AS FOLLOWS:

DRILL
3/8" DIA.
HOLE FOR
MORTISE
NUT BODY

1. For top jamb and corner bracket
applications: The door closer foot
will be attached to the door in a
manner similar to that shown for
mounting the closer body.
2. The appropriate mortise nuts
and screws will be suppled based
on door thickness.
Door construction must provide a
bridge type reinforcement to prevent
the door rail from collapsing when
through-bolts are tightened.

FOR TOP JAMB APPLICATION

FOR STANDARD AND PARALLEL ARM APPLICATION

• Screw short cover screw (#8-32 X 5/16) into top of case
approximately 2 turns
• Assemble plastic support and long cover screw (#8-32 X 1 1/4)
into bottom of case approximately 2 turns
• Hold support against case (approximately 2 turns)
between flange and screw head
• Position cover on closer and tighten screws
SHORT COVER SCREW

• Assemble plastic support and long cover screw (#8-32 X 1 1/4")
into top of case approximately 2 turns
• Screw short cover screw (#8-32 X 5/16") into bottom of case
approximately 2 turns
• Slide cover into gap between flange and screw head. Position cover
on closer and tighten screws
PLASTIC SUPPORT AND
LONG COVER SCREW

GAP

RIGHT HAND
ILLUSTRATED
PLASTIC SUPPORT AND
LONG COVER SCREW

SHORT COVER SCREW

INSERT IS REMOVABLE.
PLACE IN UNUSED OPENING

INSERT IS REMOVABLE. PLACE IN UNUSED OPENING

A7140F

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.1-c037 46.282696, Mon Apr 02 2007 18:36:56
Instance ID                     : uuid:346aa5bc-7bc5-ba44-adce-11bff4833c73
Document ID                     : adobe:docid:indd:7e773698-b34d-11df-9f34-89275d02fbe0
Rendition Class                 : proof:pdf
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:23B7B2B449B3DF11904481A7F3441F9C, uuid:8A9E4CFA320BDF11968F8866DB937BF8, uuid:A087A6005F0EDF119F328CA8B55DD912, uuid:25B7B2B449B3DF11904481A7F3441F9C, uuid:8A9E4CFA320BDF11968F8866DB937BF8, uuid:A087A6005F0EDF119F328CA8B55DD912, uuid:253E696361B3DF11904481A7F3441F9C, uuid:8A9E4CFA320BDF11968F8866DB937BF8, uuid:A087A6005F0EDF119F328CA8B55DD912, uuid:EA58079556B3DF11904481A7F3441F9C, uuid:8A9E4CFA320BDF11968F8866DB937BF8, uuid:A087A6005F0EDF119F328CA8B55DD912, uuid:ED58079556B3DF11904481A7F3441F9C, uuid:8A9E4CFA320BDF11968F8866DB937BF8, uuid:A087A6005F0EDF119F328CA8B55DD912, uuid:8A9E4CFA320BDF11968F8866DB937BF8, uuid:A087A6005F0EDF119F328CA8B55DD912, uuid:8A9E4CFA320BDF11968F8866DB937BF8, uuid:A087A6005F0EDF119F328CA8B55DD912, uuid:EF58079556B3DF11904481A7F3441F9C, uuid:C570E7645BB3DF11904481A7F3441F9C, uuid:8A9E4CFA320BDF11968F8866DB937BF8, uuid:A087A6005F0EDF119F328CA8B55DD912
Manifest Reference Document ID  : uuid:21B7B2B449B3DF11904481A7F3441F9C, uuid:899E4CFA320BDF11968F8866DB937BF8, uuid:9F87A6005F0EDF119F328CA8B55DD912, uuid:24B7B2B449B3DF11904481A7F3441F9C, uuid:899E4CFA320BDF11968F8866DB937BF8, uuid:9F87A6005F0EDF119F328CA8B55DD912, uuid:26B7B2B449B3DF11904481A7F3441F9C, uuid:899E4CFA320BDF11968F8866DB937BF8, uuid:9F87A6005F0EDF119F328CA8B55DD912, uuid:E958079556B3DF11904481A7F3441F9C, uuid:899E4CFA320BDF11968F8866DB937BF8, uuid:9F87A6005F0EDF119F328CA8B55DD912, uuid:EB58079556B3DF11904481A7F3441F9C, uuid:899E4CFA320BDF11968F8866DB937BF8, uuid:9F87A6005F0EDF119F328CA8B55DD912, uuid:899E4CFA320BDF11968F8866DB937BF8, uuid:9F87A6005F0EDF119F328CA8B55DD912, uuid:899E4CFA320BDF11968F8866DB937BF8, uuid:9F87A6005F0EDF119F328CA8B55DD912, uuid:EE58079556B3DF11904481A7F3441F9C, uuid:C370E7645BB3DF11904481A7F3441F9C, uuid:899E4CFA320BDF11968F8866DB937BF8, uuid:9F87A6005F0EDF119F328CA8B55DD912
Create Date                     : 2010:09:20 08:38:07-04:00
Modify Date                     : 2010:09:20 08:38:15-04:00
Metadata Date                   : 2010:09:20 08:38:15-04:00
Creator Tool                    : Adobe InDesign CS3 (5.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 14120 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 8
Creator                         : Adobe InDesign CS3 (5.0.4)

EXIF Metadata provided by EXIF.tools

Sargent Instructions For Installing 1431 Series Door Closers (with Hold Open Arms 'H'/UH/HZ/HZA/PH9) A7140F Low Res

Navigation menu

Versions of this User Manual:

Views

Navigation