Sato CL4XXEAW RFID Printer User Manual

Sato Corporation RFID Printer Users Manual

Users Manual

CL408e/412e Quick Guide FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: — Reorient or locate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. PN9001067 Rev B Page 1 DECLARATION OF CONFORMITY SATO America, Inc. 10350A Nations Ford Road, Charlotte, North Carolina 28273 TEL (704) 644-1650 declare under our sole responsibility that the product CL408e, CL412e complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION Please maintain the distance at least 20 cm (7.9 in) in an uncontrolled environment from the antenna's surface when using the device. See FCC OET Bulletin 56 "Hazards of radio frequency and electromagnetic fields" and Bulletin 65 "Human exposure to radio frequency electromagnetic fields." This device shall not be co-located with any other transmitting antenna. The distance from outside the case PN9001067 Rev B Page 1-1 Antenna Position (Cover open view) 2cm 0cm (It leaves sufficiently) 18cm 6cm 12cm 9cm
CL408e/412e Quick Guide Table of Contents What You Get ................................................................................. 3 Controls and Indicators ................................................................... 4 Operator Panel ................................................................... 4 LED Indicators .................................................................... 4 Adjustments ........................................................................ 4 Keys ..................................................................................... 5 Rear Panel Connections ..................................................... 5 Initial Setup ..................................................................................... 6 Connecting the Printer ........................................................ 6 Printing a Test Label ........................................................... 7 Configuring the Printer ........................................................ 8 Computer Connections ....................................................... 8 CL408e/412e Software and Drivers ................................................. 10 Label Wizard SE ................................................................. 10 Windows Drivers ................................................................. 11 What to do if it will not print ............................................................... 11 CL408e/412e Specifications ............................................................ 15 Media and Supplies ......................................................................... 16 Options ............................................................................................ 16 Safety Considerations ...................................................................... 17 Safety Information ............................................................................ 18 This Quick Guide was prepared to get you up and running quickly. It will enable you to get your new SATO CL408e/412e installed and printing with a minimum of effort. However, it is recommended that you familiarize yourself with the contents of the CL408e/412e Operator and Technical Reference Manual for detailed descriptions so you will be able to properly use the printer to its full potential. PN9001067 Rev B Page 2
What You GetThe CL408e/412eThermal Transfer printer comes packedina protectivecarton. Includedin the cartonarethefollowing items:•CL408e/412ePrinter•Quick Guide•Operator andTechnical ReferenceManual•HeadCleaningSheet•SampleRibbons andRibbon Take-UpCore•Power Cable•Test PrintoutLabels•Label WizardSE CD-ROMAfter takingthe CL408e/412efromthecartonandremoving theprotectiveplastic cover, it is ready for installation.PN 9001067 Rev B Page 3CL408e/412e Quick Guide
Controls and IndicatorsOperator PanelLED IndicatorsStatus: Dark whenOff LineGreen whenprinter is On Line.Redwhenanerror conditionexists.LCD Display: Illuminatedwhenpower is applied.Adjustments (controls behindfrontpanel)Print: Adjusts printdarkness.Offset: Adjusts amountof back/forwardfeedfor dis-pense/cut/tear-off position.Pitch: Adjusts homepositionof thelabel +/- 3.75 mm. Affectsstoppositionof label, printposition anddispense/cut po-sition.DSW2-3: Sets printer configurationPage 4 PN 9001067 Rev BCL408e/412e Quick Guide
Initial Set-UpConnectingthePrinter1. Locatea suitablespotfor theprinter. Itshouldbewithin 6 ft. of thehostif usinganIEEE1284 Parallel interfaceor within35 ft. if using aHigh SpeedRS232 interface. For other types of Plug-Ininterfacecards, see theOperator andTechnical ReferenceManual. Makesurethereis adequateroom aboveandto therightof theprinter for thela-bel access door to swingopen.2. PlugtheAC cableprovidedintotheback of theprinter andconnectto a suitable 115VAC outlet.3. Opentheprintheadandloadtheribbon usingtheribbonroutingguidelocatedontheinsideof the topcover. Besuretopositiontheribbonroll correctly ontheRibbonSupply Spindleandplacethesparetake-upcoreontheTake-UpSpindle. Tapethefreeendof theribbonto thetake-upcoresothatitwill take-upwhenrotatinginacounter clockwisedirection.4. Placethelabel roll ontheLabel Supply SpindleandpushthegreenLabel Roll Retainer on the spindleuntil it pushes the label roll all theway totheinsideof theprinter. Thelabels shouldcomeoff the bot-tomof theroll (labels woundface-inontheroll).5. Routethelabels as indicatedby the label routingdiagramon the in-sideof thetopcover. Thelabels shouldgo under theplastic guide,throughtheLabel Sensor Assembly, under the printheadandout thefront of theprinter. PositiontheLabel EdgeGuide towardtheinsideof theprinter until itbarely contacts theoutsideedgeof thelabels.6. ClosethePrint HeadLatchandthenthesideaccess door last.7. Select the proper label sensingmethodusingthefrontpanel DIPswitches. The DIP switchfunction chartis locatedontheinsideofthefrontcover. Theprinter comes fromthefactory set for label gapdetection (DSW2-2, DSW3-3 both OFF). NotethattheOFF positionfor theDSW switches is downandtheON positionup.8. Apply power by placingthefrontpanel Power switchin the “1" posi-tion.9. The Power andOn-Line LEDs shouldbeilluminatedandONLINEshouldbedisplayedontheLCD.10. Press theLINE key once. TheOnLineLED shouldgo outandOFFLINE shouldbedisplayedontheLCD.11. Press theFEED key once. Theprinter shouldfeedout onelabel andstop.Page 6 PN 9001067 Rev BCL408e/412e Quick Guide
CL408e/412e Quick Guide Safety Information PN9001067 Rev B Page 18
CL408e/412e Quick Guide Safety Information PN9001067 Rev B Page 19
CL408e/412e Quick Guide Safety Information PN9001067 Rev B Page 20
CL408e/412e Quick Guide Safety Information PN9001067 Rev B Page 21

Navigation menu