Sato SATOTR3 RFID Reader/Writer Module Transmitter User Manual Install 2
Sato Corporation RFID Reader/Writer Module Transmitter Install 2
Sato >
Contents
- 1. Installation Manual 1
- 2. Installation Manual 2
Installation Manual 1
Installation Caution Turn the Power OFF and unplug the power cable before installation. 1. Remove the Cover LH Cover LH Remove the screws ( 4 positions) 2. Install the RFID Interface Board ASSY Plug in the Interface Board and fix it on the printer with two screws. 2. Pan Head Screw (M3*6, SW+WL) 1. RFID Interface Board ASSY 3. Install the RFID Module Board ASSY ①The assembly of the eight spacers is carried out to Module BR. Module BR ②RSDRV board is fixed with four screws. Signal cable is fixed on tie lap. ③RFID module is fixed with four screws. Spacer(L=30mm) Spacer(L=15mm) Pan Head Screw (M3*6, SW+WS) ④The signal cable which has come out of the DRV board is connected to the connector (CN1) of RFID module. RFID module DRV Board Tie lap 4pcs 4pcs 8pcs ⑤Fix the Module Board on the Center Frame of the upper-left side of the Motor with two screws. S-tight Screw (M3*6) RFID Module Board ASSY ※Tightening the screws may be a little hard. 4. Attach the Cable Clamp Attach the Cable Clamp on the Cont PCB Bracket. 7. Cable Clamp The position is the edges of the Bracket as shown with the red arrows. 5. Remove the Sensor Cover Slide the Sensor Knob to the arrow direction to the end. Then pull out the Sensor Cover. Sensor Cover Sensor Knob 6. Remove the Antenna Cover Removing the two screws release the Antenna Cover. Be sure to not lose these screws as they are to be used for installation. Antenna Cover Antenna Board 7. Install the RFID Antenna Board Set ①Antenna BR and an antenna board are fixed by two nylon rivets. Antenna BR Nylon rivet ②Four collars are put into an antenna cover. Collar ③Fix the Antenna BR on the reverse side of the removed Antenna Cover with four P-tight screws as shown in the picture. 6. P-tight Screw (M2.6*6) 8. Re-install the Antenna Cover (with Antenna) Put the Antenna Cable through the hole on the Center Frame for the pulled-out Sensor to the Cont PCB side and re-install the Antenna Cover with the screws removed in the process 6. Cable of 5. RFID Antenna Board Set 9. Return the Sensor Put the Sensor Cover on the Sensor and slide the Sensor to the end. Sensor Cover 10. Fix the Antenna Cable on the Sensor Sensor Remove the Spring on the end of the Sensor from the Cont PCB side. Fix the Antenna Cable on the bottom of the Sensor with the removed Spring. Confirm that the Cable does not get jammed by sliding the Sensor. Spring Cable 1 turn 11. Connect the Antenna Cable ①Ferrite core is attached to an antenna cable. ②Connect the Antenna Cable to the connector at the bottom of the Module Board and fix its route with the Clamp. Ferrite core Clamp Antenna Cable RFID Module Board 12. Connect the RFID Cable SET ①Ferrite core is attached to RFID cable set. ②Connect the Interface Board and the Module Board via the RFID Cable and fix its route with the Cable Clamp. Ferrite core Cable 1 turn RFID Cable Set Cable Clamp
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 5 Creator : .橡.Microsoft Word Create Date : 2004:07:14 09:07:45 Title : .橡.Install_2版.PDF Author : .橡.Unknown Producer : Acrobat PDFWriter 3.0J WindowsEXIF Metadata provided by EXIF.tools