Savant Systems SHC2000 Smart Host Controller User Manual 009 1326 00 Savant Smart Host SHC 2000 QRG
Savant Systems LLC Smart Host Controller 009 1326 00 Savant Smart Host SHC 2000 QRG
User Manual.pdf
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2603525 |
| Application ID | xhnd2nQDENuOOnTTfjp3vg== |
| Document Description | User Manual.pdf |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 110.41kB (1380072 bits) |
| Date Submitted | 2015-05-04 00:00:00 |
| Date Available | 2015-10-31 00:00:00 |
| Creation Date | 2015-03-27 17:44:46 |
| Producing Software | Mac OS X 10.9.5 Quartz PDFContext |
| Document Lastmod | 2015-04-24 13:19:58 |
| Document Title | 009-1326-00 Savant Smart Host (SHC-2000) QRG |
| Document Creator | Pages |
| Document Author: | David Wright |
For Product Info Savant® Smart Host with Control Quick Reference Guide Box Contents Rear Panel (1) Savant® Smart Host with Control (SHC-2000-00) (1) 5V DC 3A Power Supply with 4 Quick Change AC Adapters (025-XXXX-xx) (2) M3x6 mm Flathead Philips Screw Black (039-00101-xx) (1) Wall Mount Bracket (074-0585-xx) (1) Host Mount Bracket (074-0584-xx) (2) 6-pin Screw Down Plug-in Connector Black (028-0664-xx) (2) 3-pin Screw Down Plug-in Connector Black (028-0665-xx) (1) Quick Reference Guide (this document) Specifications Reset (hole) Environmental Temperature 32° to 104° F (0° to 40° C) Humidity 10% to 90% Relative Humidity (noncondensing) Cooling 10 CFM Maximum BTU 51.15 BTU/hr Note: This will reset the network settings back to factory defaults. Any static IP Addresses or Wi-Fi settings will be lost. Power Input 5V DC 3A - Connect to included power supply. Status LED Off: Disconnected from power supply. Amber: Controller is booting/rebooting and is disconnected from the network. Amber Blinking: Smart Host is not connected to a wired Ethernet network and has not joined a Wi-Fi network. Green: Connected to wired Ethernet or Wi-Fi Network. Dimensions and Weight Height 1.58 in (4 cm) Width 7.86 in (19.9 cm) Depth 7.65 in (19.4 cm) Weight Rack Space Net: 1.3 lb (0.58 kg) TOSLink (Optical) digital audio output. Shipping: 2.1 lb (0.95 kg) Digital Audio Output 1U Power Input Power 5V DC 3A Maximum Power 15 watts Ethernet RoHS Compliant RS-232 See RS-232 Wiring for pinouts. IR 6-pin Screw Down Plug-in Connector. Used to send IR signals to control devices with an IR input or IR receiver via an IR flasher (5V tolerant only). See IR Wiring for important precautions regarding IR functionality before making any connections. Relay 3-pin Screw Down Plug-in Connector. See Relay Wiring for pinouts. Normally Open (NO) Normally Closed (NC) to control devices requiring basic on/off operation. DC Voltage Max: 30V DC 1A. da Vinci 7.2 Chassis Installation The Smart Host can be installed on a solid, flat, level surface such as a table, cabinet or shelf, or wall mounted using the included bracket. The location should be dry, well ventilated, and out of direct sunlight. Rack Installation The optional RCK-3000-xx provides a ventilated shelf for mounting up to 2 Smart Hosts. Wall Bracket Installation 3-pin Screw Down Plug-in Connector. See GPIO Wiring for pinouts. A wall bracket is included that can be used to mount the Smart Host to a wall or back of a cabinet. This bracket consists of two pieces, one for the host and one for the wall. 1. Attach the host bracket to the rear of the host using the included M3x6 mm Flathead Philips Screws. GPIO 2. Attach the wall bracket to the wall. Screws to attach are not included. GPIO Input: When configured as an input, the processor will look for a low (<0.8V DC) or a high (>2.4V DC ) state. Minimum 0V DC / Maximum 12V DC GPIO Output: When configured as an output, the port provides a binary output of 0-12V DC 150mA max. 3. Position the host over the wall bracket and gently slide into place. See Wall Bracket Diagram on pg 2. SHC-2000-00 | 009-1326-00 | 150327 Copyright © 2015 Savant Systems, LLC Ports 1-2 RS-232 - CTS/RTS handshaking. CTS/RTS Handshaking availability based on component profile. Minimum Supported Release Savant OS Connection to this port will disable Wi-Fi settings. Used to transmit and receive serial binary data to and from serial controllable devices. Compliance FCC Part 15 | CE Mark | C-Tick | UL | ICES-003 | Wi-Fi Alliance 10/100/1000 Base-T auto-negotiating port. 8-pin RJ-45 female. Wi-Fi® (802.11 b/g/n dual band 2.4 GHz and 5.0 GHz) Safety and Emissions Connect to digital optical audio input on switcher for using the Audio Interrupt Service (AIS). 8-pin RJ-45 female. Standards Wireless Press and hold for 5 seconds while powered On to clear Wi-Fi or wired Ethernet settings. Status LED will blink rapidly when reset is complete. of 2 45 Perseverance Way, Hyannis, MA 02601 savant.com | 508.683.2500 GPIO Pull Down Resistor (PD) Usage Wall Bracket Diagram GPIO pins are configured as inputs and are pulled high to 12V while the host is booting up. To make the GPIO signal low during a host reboot and/or a power cycle, attach the GPIO 1 pin to the PD pin. The PD pin is a 1K ohm pull down resistor (to signal ground) which keeps the GPIO output below 0.8V during processor boot times. Relay Wiring Relay ports are used when a device is controlled via a normally open (NO) or normally closed (NC) relay. Wiring and Connections RS-232 Wiring Refreshing the IP Connection • Reset Network Settings via Rear Panel Button • Cycle Power • Hot Plug the Ethernet (LAN) Connection Regulatory FCC (see RED portions) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: CTS/RTS handshaking is supported for flow control based on the profile used in the configuration. RJ-45 to DB9 Adapters Refer to the RS-232 Conversion to DB9 and RS-422/485 Pinout Application Note located on the Savant Community for more information on RJ-45 to DB9 adapters offered by Savant. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Note: The SHC-2000 does not support RS-422/485. IR Wiring IR connections are made using 6-pin Screw Down Plug-in Connectors supplied with the Smart Host. The wire slips into the hole and locks with a screw located at the top of the connector. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: While not shown in the diagram above, IR connections 4 to 6 follow the same wiring as 1 to 3. IMPORTANT! IR Wiring Precautions Ensure that all IR emitters are within 15 feet (4.6 meters) from the controllers location. • Use of 3rd party flashing IR emitters with Talk Back is not recommended. These types of emitters can draw voltage away from the IR signal that can degrade IR performance. • FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. GPIO Wiring This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. General Purpose Input/Outputs (GPIO) are binary I/O ports used on Savant controllers to trigger an action within the system. Events can control a device, such as turning on an amplifier (output) or detecting a state change for a device (input) to perform a workflow. Pin 2 is used for input or output depending on configuration. SHC-2000-00 | 009-1326-00 | 150327 Copyright © 2015 Savant Systems, LLC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 2 of 2 45 Perseverance Way, Hyannis, MA 02601 savant.com | 508.683.2500
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Format : application/pdf Creator : David Wright Title : 009-1326-00 Savant Smart Host (SHC-2000) QRG Create Date : 2015:03:27 17:44:46Z Creator Tool : Pages Modify Date : 2015:04:24 13:19:58+08:00 Metadata Date : 2015:04:24 13:19:58+08:00 Producer : Mac OS X 10.9.5 Quartz PDFContext Document ID : uuid:1567aaaa-acf6-4b6e-8074-90f5f12cd09f Instance ID : uuid:9c26e008-3441-4c13-839f-bc9342045e30 Has XFA : No Page Count : 2 Author : David WrightEXIF Metadata provided by EXIF.tools