Schneider Electric Systems Canada EB450-XXF01 Remote Radio Data Modem Base/Repeater User Manual temp warning E Series R3

Trio Datacom Pty Ltd (a wholly owned company of Schneider Electric) Remote Radio Data Modem Base/Repeater temp warning E Series R3

Users Manual 1of 2

User ManualE Series Data Radiowww.trio.com.auER450 Remote Data RadioEB450 Base StationEH450 Hot Stand-by Base StationIssue 4: May 2003
Page 2E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.WarrantyAll equipment supplied by Trio DataCom Pty. Ltd. is warranted againstfaulty workmanship and parts for a period of twelve (12) months fromthe date of delivery to the customer. During the warranty period TrioDataCom Pty. Ltd. shall, at its option, repair or replace faulty parts orequipment provided the fault has not been caused by misuse,accident, deliberate damage, abnormal atmosphere, liquid immersionor lightning discharge; or where attempts have been made byunauthorised persons to repair or modify the equipment.The warranty does not cover modifications to software. All equipmentfor repair under warranty must be returned freight paid to Trio DataComPty. Ltd. or to such other place as Trio DataCom Pty. Ltd. shallnominate. Following repair or replacement the equipment shall bereturned to the customer freight forward. If it is not possible due to thenature of the equipment for it to be returned to Trio DataCom Pty. Ltd.,then such expenses as may be incurred by Trio DataCom Pty. Ltd. inservicing the equipment in situ shall be chargeable to the customer.When equipment for repair does not qualify for repair or replacementunder warranty, repairs shall be performed at the prevailing costs forparts and labour. Under no circumstances shall Trio DataCom Pty.Ltd.’s liability extend beyond the above nor shall Trio DataCom Pty.Ltd., its principals, servants or agents be liable for the consequentialdamages caused by the failure or malfunction of any equipment.Important Notice© Copyright 2002 Trio DataCom Pty. Ltd. All Rights ReservedThis manual covers the operation of the E Series of Digital DataRadios. Specifications described are typical only and are subject tonormal manufacturing and service tolerances.Trio DataCom Pty Ltd reserves the right to modify the equipment, itsspecification or this manual without prior notice, in the interest ofimproving performance, reliability or servicing. At the time ofpublication all data is correct for the operation of the equipment atthe voltage and/or temperature referred to. Performance dataindicates typical values related to the particular product.This manual is copyright by Trio DataCom Pty Ltd. All rightsreserved. No part of the documentation or the information suppliedmay be divulged to any third party without the express writtenpermission of Trio DataCom Pty Ltd.Same are proprietary to Trio DataCom Pty Ltd and are supplied forthe purposes referred to in the accompanying documentation andmust not be used for any other purpose. All such informationremains the property of Trio DataCom Pty Ltd and may not bereproduced, copied, stored on or transferred to any other media orused or distributed in any way save for the express purposes forwhich it is supplied.Products offered may contain software which is proprietary to TrioDataCom Pty Ltd. However, the offer of supply of these productsand services does not include or infer any transfer of ownership ofsuch proprietary information and as such reproduction or reusewithout the express permission in writing from Trio DataCom PtyLtd is forbidden. Permission may be applied for by contacting TrioDataCom Pty Ltd in writing.Part A - Preface!Warning :- RF ExposureThe radio equipment described in this user manual emits low levelradio frequency energy. The concentrated energy may pose a healthhazard depending on the type of antenna used. In the case of a non-directional antenna do not allow people to come within 0.5 metres ofthe antenna when the transmitter is operating. In the case of adirectional antenna do not allow people to come within 6 metres of theantenna when the transmitter is operating.Related ProductsER450 Remote Data RadioEB450 Base/Repeater StationEH450 Hot Stand-by Base StationOther Related Documentationand ProductsQuick Start GuideTVIEW+ Management SuiteDigital Orderwire Voice Module (EDOVM)Stream Router/Multiplexer (95MSR)Revision HistoryIssue 1 July 2002 Intitial ReleaseIssue 2 August 2002 Added EH450 Quick Start Sectionand Specifications SectionIssue 3 November 2002 Major Edits to TVIEW and minor editsto quick start sections.Part A  Preface
Page 3E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.ContentsContentsSECTION 1Part A  Preface 2Warranty 2Important Notice 2Related Products 2Other Related Documentation and Products 2Revision History 2Part B  E Series Overview 4Definition of E Series Data Radio 4E Series Product Range 4E Series – Features and Benefits 4Model Number Codes 6Standard Accessories 7Part C  Applications 8Generic Connectivity 8Application Detail 8Systems Architecture 9Part D  System Planning and Design 11Understanding RF Path Requirements 11Examples of Predictive Path Modelling 12Selecting Antennas 14Data Connectivity 15Power Supply and Environmental Considerations 18Physical Dimensions of the Remote Data Radio 19Physical Dimensions of the Base Station 20Physical Dimensions of the Hot Standby Base Station 21Part E  Getting Started 22ER450 Quick Start Guide 22EB450 Quick Start Guide 28EH450 Quick Start Guide 31Part F - Operational Features 36Multistream functionality (SID codes) 36Collision Avoidance (digital and RFCD based) 36Digipeater Operation 36TVIEW+ Diagnostics 36Part G  Commissioning 37Power-up 37LED Indicators 37Data Transfer Indications 37Antenna Alignment and RSSI Testing 37Link Establishment and BER Testing 37VSWR Testing 37Part H  Maintenance 38Routine Maintenance Considerations 38SECTION 2Part I  TVIEW+ Management Suite -Programmer 40Introduction 40Installation 40TVIEW+ Front Panel 41Programmer 41Part J  TVIEW+ Management Suite -Remote Diagnostics & NetworkController 53Introduction 53System Description 53Operating Instructions 55Interpreting Poll Results 66Part K  Appendices 67Appendix A - Application and Technical Notes 67Appendix B - Slip Protocol 67Appendix C - Firmware Updates 68Part L  Specifications 69Part M  Support Options 70Website Information 70E-mail Technical Support 70Telephone Technical Support 70Contacting the Service Department 70
Page 4E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Part B  E Series OverviewDefinition of E Series Data RadioThe E Series is a range of wireless modems designed for thetransmission of data communications for SCADA, telemetry, andany other information and control applications that utilise ASCIImessaging techniques. The E Series uses advanced “digital”modulation and signal processing techniques to achieveexceptionally high data throughput efficiency using traditionallicensed narrow band radio channels.The products are available in many frequency band and regulatoryformats to suit spectrum bandplans in various continental regions.The range is designed for both fixed point to point (PTP), andmultiple address (MAS) or point to multipoint (PMP) systems.E Series Product RangeThe E Series range consists of the basic half duplex “Remote”radio modem, an extended feature full duplex Remote radiomodem, and ruggedised Base Station variants, including anoptional Hot Standby controller to control two base station units ina redundant configuration.Frequency band variants are indicated by the band prefix andmodel numbering. (See Model Number Codes)Part B  E Series OverviewE Series  Features and BenefitsCommon Features and Benefits of the ESeries Data Radio• Up to 19200bps over-air data rates using programmableDSP based advanced modulation schemes• Designed to various International regulatory requirementsincluding FCC, ETSI and ACA• Superior receiver sensitivity• Fast data turnaround time <10mS• Flash upgrade-able firmware – insurance against obsolescence• Multi-function bi-colour Tx/Rx data LEDS showing Port activity(breakout box style), as well as LEDs indicating Tx, Rx, RFSignal, Data Synchronisation and DC Power status of theradio• Rugged N type antenna connectors on all equipment• High temperature transmitter foldback protection• Two independent configurable data ports and separate systemport• Higher port speeds to support increased air-rate (up to76800bps on Port A and 38400bps on Port B)• Independent system port for interruption free programming anddiagnostics (in addition to two (2) user ports)• 9600bps in 12.5 kHz radio channels with ETSI specifications• Remote over-the-air configuration of any radio from any location• Multistream™ simultaneous data streams allows for multiplevendor devices / protocols to be transported on the one radionetwork• Flexible data stream routing and steering providing optimumradio channel efficiency – complex data radio systems can beimplemented with fewer radio channels• The ability to duplicate data streams – that is, decode the sameoff-air data to two separate ports.• Multi-function radio capable of dropping off one stream to a portand forward on or repeat (store and forward) the same or otherdata.• Stand-alone internal store and forward operation – buffered storeand forward operation even in the ER remote units• Unique integrated C/DSMA collision avoidance technologypermits simultaneous polling and spontaneous reportingoperation in the same system• Digital receiver frequency tracking for long term data reliability• Network wide non intrusive diagnostics which runssimultaneously with the applicationER450 Remote RadioEB450 Base / Repeater StationEH450 Hot Standby Base Station
Page 5E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Part B  E Series Overview• Network wide diagnostics interrogation which can beperformed from anywhere in the system including any remotesite• Diagnostics will route its way to any remote or base / repeatersite regardless of how many base / repeater stations areinterconnected• Full range of advanced features available within NetworkManagement and Remote Diagnostics package – BER testing,trending, channel occupancy, client / server operation, etc.• On board memory for improving user data latency – increaseduser interface speeds• Full CRC error checked data – no erroneous data due tosquelch tails or headers• Radio utilises world standard HDLC as its transportationprotocol• Various flow control and PTT control mechanisms• Configurable backward compatibility with existing D Seriesmodulation scheme for use within existing networks• Digital plug in order wire option for commissioning andoccasional voice communications without the need to inhibitusers application dataFeatures and Benefits of ER450 RemoteData Radio• Optional full duplex capable remote – separate Tx and Rx portsfor connection to an external duplexer• New compact and rugged die cast case with inbuilt heatsink• Low power consumption with various sleep modes• Rugged N type antenna connectors• In-line power supply fuses• Data Port “breakout box” style flow LEDs for easiertroubleshootingFeatures and Benefits of EB450 StandardBase / Repeater Station• Competitively priced high performance base• Incorporates a rugged 5W power amplifier module• External input for higher stability 10MHz reference – GPSderivedFeatures and Benefits of EH450 Hot StandbyBase / Repeater Station• Individual and identical base stations with separate control logicchangeover panel• ALL modules are hot swapable without any user downtime• Flexible antenna options – single, separate Tx & Rx, two Txand two Rx• Increased sensitivity with receiver pre-amplifier• Both on-line and off-line units monitored regardless of activestatus• External input for higher stability 10MHz reference – GPSderived
Page 6E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Model Number CodesD, E & S Series Data Radios - Part Number Matrix = Tyxxx-aabbb-cdT y xxx-aa bbb-cdOptions - Base Stations* Options - Remote Antenna Connector*0= No Options 0= No Options (Standard)1= 450MHz Band Reject [DUPLX450BR]N= N Connector (D Series only)2= 450MHz Band Reject (<9MHz split)[DUPLX450BR/5]S= SMA Connector (SR450 only)3= 450MHz Band Pass [DUPLX450BP]4= 900MHz Band Reject [DUPLX900BR]5= 900MHz Band Pass [DUPLX900BP]6= 900MHz Band Pass (76MHz split)[DUPLX852/930]Note: Specify Internally or Externally fitted. Externally fittered duplexes require feeder tails.Options*0= No OptionsD= Diagnostics - [DIAGS/D, DIAGS/DH, DIAGS/E or DIAGS/EH] (D & E Series Only)H= Extended Temp Option [HITEMP]N= Remote Fitted into NEMA Enclosure [NEMA 4/R]F= Full Duplex Operation [ERFD450] (ER450 only)X= Full Duplex Operation [ERFD450 & DIAGS/E] (ER450 only)RF Channel Data Rate & Bandwidth (Internal Modem)D Series E SeriesA01 = ACA 4800bps in 12.5kHz A01 = ACA 4800#/ 9600bps in 12.5Hz 001 = 12.5kHz (No Modem Fitted)A02 = ACA 9600bps in 25kHz A02 = ACA 9600#/ 19k2bps in 25kHz 002 = 25kHz (No Modem Fitted)F01 = FCC 9600bps in 12.5kHz F01 = FCC 9600#/ 9600bps in 12.5kHz 241 = 2400bps in 12.5kHz [24SR]*F02 = FCC 19k2bps in 25kHz 242 = 2400bps in 25kHz [24SR]*E01 = ETSI 9600bps in 12.5kHz 482 = 4800bps in 25kHz [48SR]*E02 = ETSI 19k2bps in 25kHzFrequency (200 & 400 MHz range) Frequency (900 MHz range) (D & S Series Only)39 = 208 to 240MHz (Tx & Rx) 07 = (Tx) 847 to 857MHz (Rx) 923 to 933MHz (D Series only, 1W Full Duplex)50 = 403 to 417MHz (Tx & Rx) 10 = (Tx) 848 to 858MHz (Rx) 920 to 934MHz58 = (Tx) 406 to 421MHz (Rx) 415 to 430MHz 06 = (Tx) 923 to 933MHz (Rx) 847 to 857MHz (D Series only, 1W Full Duplex)59 = (Tx) 415 to 430MHz (Rx) 406 to 421MHz 11 = (Tx) 920 to 934MHz (Rx) 848 to 858MHz56 = 418 to 435MHz (Tx & Rx) 12 = 855 to 860MHz (Tx & Rx)57 = 428 to 443MHz (Tx & Rx) 14 = (Tx) 925 to 943MHz (Rx) 906 to 924MHz 55 = 436 to 450MHz (Tx & Rx) 15 = (Tx) 904 to 922MHz (Rx) 925 to 943MHz51 = 450 to 465MHz (Tx & Rx) 16 = 924 to 944MHz (Tx & Rx)52 = 465 to 480MHz (Tx & Rx)53 = 480 to 494MHz (Tx & Rx) Note: Other frequency bands available upon request.54 = 505 to 518MHz (Tx & Rx)27 = (Tx) 511 to 515MHz (Rx) 501 to 505MHz48 = 395 to 406MHz (Tx & Rx)Generic Frequency Band200 = 208 to 245MHz (D & S Series only) NOTES:450 = 400 to 518MHz (E & S Series only) * Additional charges apply. Must be ordered seperately. Please refer to price list. 900 = 800 to 960MHz (D & S Series only)# Provides compatibility with D Series radio Items in [ ] parenthesis refer to actual Trio part numbersUnit TypeR= Remote StationB= Base / Repeater Station Standards: ACA - Australian Communications AuthorityS= Standard Base / Repeater Station (D Series Only) FCC - Federal Communications CommissionH= Hot Standby Base / Repeater (D & E Series Only) ETSI - European Telcommunication Standards InstituteModel TypeD= D Series FamilyE= E Series FamilyS= S Series FamilyExample:E R 450-51 A02-D0The above example specifies: E Series, Remote Radio, generic 450MHz band, with a specific frequency of 450MHz to 465MHz,a 96/19.2kbps modem, with a bandwidth of 25kHz, diagnostics and standard N type connector.Version: 11/02S Series
Page 7E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Part B  E Series OverviewPart Number DescriptionDuplexersDUPLX450BR Duplexer BAND REJECT 400-520 MHz for usewith Base / Repeater / Links. For Tx / Rxfrequency splits >9MHz. (Fitted Externally for aLink, Intenally or Externally for Base / Repeater)DUPLX450BR/5 Duplexer BAND REJECT 400-520 MHz for usewith Base / Repeater / Links. For Tx / Rxfrequency splits <9MHz. (Fitted Externally for aLink, Intenally or Externally for Base / Repeater)DUPLX450BP Duplexer PSEUDO BAND PASS Cavity 400-520 MHz for External use with Base / Repeater/ Links.Notes:1. Frequencies must be specified at time of order.2. Interconnecting (Feeder Tail) cables must be orderedseparately for Externally fitted Duplexers.AntennasANT450/9A Antenna Yagi 6 Element 9dBd Aluminium 400-520 MHz c/w mtg clampsANT450/9S Antenna Yagi 6 Element 9dBd S/Steel 400-520MHz c/w mtg clampsANT450/13A Antenna Yagi15 Element 13dBd Aluminium 400-520 MHz c/w mtg clamps.ANT450/13S Antenna Yagi 15 Element 13dBd S/Steel 400-520 MHz c/w mtg clamps.ANTOMNI/4 Antenna Omni-directional Unity Gain SideMount Dipole 400-520 MHz c/w galv. clampANT450/D Antenna Omni-directional Unity Gain GroundIndependant Dipole 400-520 MHz c/w 3mcable, mounting bracket & BNC connectorANT450/6OM Antenna Omni-directional 6dBd 400-520 MHzc/w mtg clampsANT450/9OM Antenna Omni-directional 9dBd 400-520 MHz c/w mtg clampsNote:1. Frequencies must be specified at time of order.Power SuppliesPS13V82A Power Supply 13.8V 2A 240VACPS13V810A Power Supply Switch Mode 240VAC 13.8V 10Afor Base Stations – Battery Charge CapabilityPart Number DescriptionRF Cables and AccessoriesNM/NM/TL Feeder Tail - N Male to N Type Male 50cm fullysweep testedNM/NM/TLL Feeder Tail - N Male to N Type Male 1 metrefully sweep testedRFCAB5M 5.0m RG-58 type Antenna Feeder Cableterminated with N type Male ConnectorsRFCAB5M2 5.0m RG-213 type Antenna Feeder Cableterminated with N type Male ConnectorsRFCAB10M 10.0m RG-213 type Antenna Feeder Cableterminated with N type Male ConnectorsRFCAB20M 20.0m RG-213 type Antenna Feeder Cableterminated with N type Male ConnectorsRFCAB20M4 20.0m LDF4-50 type (1/2" foam dialectric)Antenna Feeder Cable terminated with N typeMale ConnectorsLGHTARRST Lightning Surge Arrestor In-line N Female to NFemaleMultiplexers95MSR/6 Multiplexer/Stream Router – 6 Port with RS-232I/faces and Manual95MSR/9 Multiplexer/Stream Router – 9 Port with RS-232I/faces and ManualNetwork Management DiagnosticsDIAGS/E Network Management and Remote DiagnosticsFacilities per Radio – E SeriesDIAGS/EH Network Management and Remote DiagnosticsFacilities – E Series for EH450SoftwareTVIEW+ Configuration, Network Management andRemote Diagnostics SoftwareOtherNEMA 4 /R Stainless Steel Enclosure for Remote SiteEquipment.Size 600mm (h) x 600mm (d) x580mm (w) – Room for Third Party RTU / PLCequip. (Approx. 400(h) x 600(d) x 580mm(w)HITEMP Extended Temperature Option for S, D and ESeries Radios -30 to +70CEDOVM Digital Order Wire Voice ModuleERFD450 ER450…. Conversion to Full Duplex Operation(N Type – Tx Port, SMA - Type Rx Port)Note: Requires external duplexerERFDTRAY 19" Rack Tray for Mounting of ER450 Full DuplexRadio and External Band Reject DuplexerStandard Accessories
Page 8E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Part C  ApplicationsPart C  ApplicationsGeneric ConnectivityThe E Series has been designed for SCADA and telemetryapplications, and any other applications that use an ASCIIcommunications protocol, and which connect physically using theRS232 interface standard (although converters can be used toadapt other interfaces such as RS422/485, RS530/V35, G703 etc).Any protocol that can be displayed using a PC based terminalprogram operating via a serial comm port is suitable fortransmission by the E Series radio modems.An ASCII protocol is any that consists of message strings formedfrom ASCII characters, that being defined as a 10 or 11 bit blockincluding start and stop bits, 7 or 8 data bits and optional paritybit(s). Port set-up dialog that includes the expressions “N,8,1”, orE,7,2” or similar indicate an ASCII protocol.Most of the dominant telemetry industry suppliers utilise proprietaryASCII protocols, and also common “open standard” industryprotocols such as DNP3, MODBUS, TCP/IP, and PPP. These areall ASCII. based protocols.Industries and ApplicationsThe E Series products are widely used in point-to-point and point-to-multipoint (multiple access) applications for remoteinterconnection of PLC’s, RTU’s, dataloggers, and other datamonitoring and control devices including specialist utility devices(such as powerline ACR’s). In addition, other applications such asarea wide security and alarm systems, public information systems(traffic flow and public signage systems) and environmentalmonitoring systems.Application DetailSCADA SystemsThis is where one or more centralised control sites are used tomonitor and control remote field devices over wide areas.Examples include regional utilities monitoring and controllingnetworks over entire shires or a greater city metropolis’. Industrysectors include energy utilities (gas and electricity distribution),water and sewerage utilities, and catchment and environmentgroups (rivers, dams, and catchment management authorities).Telemetry SystemsDedicated telemetry control systems interconnecting sequentialdevices where cabling is not practical or distances areconsiderable.Examples include ore conveyor or slurry pipeline systems, simplewater systems (pump and reservoir interlinking), broadcast industry(linking studio to transmitter) etc.Information SystemsPublic Information systems such as freeway vehicle flow and traveltime monitoring, and feedback signage, parking signage systems,meteorological stations etc.
Page 9E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Part C  ApplicationsSystems ArchitecturePoint-to-PointThis simple system architecture provides a virtual connectionbetween the two points, similar to a cable. Dependant of thehardware chosen, it is possible to provide a full duplex connection(i.e. data transfer in both directions simultaneously) if required.Point-to-Multipoint SystemsIn a multiple access radio system, messages can be broadcastfrom one (master) site to all others, using a half duplex radiosystem, or from any site to all others, using a simplex radiochannel.Half duplex systems often utilise a full duplex master, to make thesystem simpler, and to operate faster.In either case, it will be necessary for the application to support anaddressing system, since the master needs to be able to selectwhich remote device it wishes to communicate to. Normally, theradio system is allowed to operate “transparently”, allowing theapplication’s protocol to provide the addressing, and thus controlthe traffic. Where the application layer does not provide theaddressing, the E Series can provide it using SID codes™. (SeePart F - Operational Features)
Page 10E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Part C  ApplicationsDigipeater SystemsThis configuration is used where all sites are required tocommunicate via a repeater site. A repeater site is used because ithas a position and/or height advantage and thus provides superioror extended RF coverage. The radio modem at the repeater doesnot have to be physically connected to the application’s mastersite. Information from the application’s master is transmitted to therepeater via radio, and the repeater then relays this information tothe other field sites. In this scenario, the repeater is the masterfrom an RF point of view, and the application master is effectively a“remote” from an RF point of view, even though it is controlling thedata transfer on the system.Store and Forward SystemsStore and forward is used as a way of extending RF coverage byrepeating data messages from one site to another.This can be done globally using the inbuilt data repeating functions, orselectively using intelligent address based routing features available insome PLC/RTU protocols.In this case it is necessary for all units on the system to operate inhalf duplex mode (only key-up when transmitting data), so thateach site is free to hear received signals from more than onesource.
Page 11E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Part D  System Planning and DesignPart D  System Planning and DesignUnderstanding RF PathRequirementsA radio modem needs a minimum amount of received RF signal tooperate reliably and provide adequate data throughput.In most cases, spectrum regulatory authorities will also define orlimit the amount of signal that can be transmitted, and thetransmitted power will decay with distance and other factors, as itmoves away from the transmitting antenna.It follows, therefore, that for a given transmission level, there will bea finite distance at which a receiver can operate reliably withrespect to the transmitter.Apart from signal loss due to distance, other factors that will decaya signal include obstructions (hills, buildings, foliage), horizon(effectively the bulge between two points on the earth), and (to aminimal extent at UHF frequencies) factors such as fog, heavyrain-bursts, dust storms, etc.In order to ascertain the available RF coverage from a transmittingstation, it will be necessary to consider these factors. This can bedone in a number of ways, including(a) using basic formulas to calculate the theoreticallyavailable signal - allowing only for free space loss due todistance,(b) using sophisticated software to build earth terrain modelsand apply other correction factors such as earth curvatureand the effects of obstructions, and(c) by actual field strength testing.It is good design practice to consider the results of at least two ofthese models to design a radio path.
Page 12E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Part D  System Planning and DesignExamples of Predictive PathModellingClear line of siteRadio path with good signal levels, attenuated only by free spaceloss.Obstructed Radio PathThis path has an obstruction that will seriously degrade the signalarriving at the field site. obstpath.pl3 Major Repeater Site Field Site Elevation (m) 703.83 309.67 Latitude 030 43 55.92 S 030 56 24.00 S Longitude 150 38 49.51 E 150 38 48.00 E Azimuth 180.10 0.10 Antenna Type ANT450/6OM ANT450/9AL Antenna Height (m) 40.00 5.00 Antenna Gain (dBi) 8.15 11.15 Antenna Gain (dBd) 6.00 9.00 TX Line Type LDF4-50 LDF4-50 TX Line Length (m) 40.00 5.00 TX Line Unit Loss (dB/100 m) 6.79 6.79 TX Line Loss (dB) 2.72 0.34 Connector Loss (dB) 2.00 2.00 Frequency (MHz) 450.00 Path Length (km) 23.04 Free Space Loss (dB) 112.78 Diffraction Loss (dB) 16.71 Net Path Loss (dB) 117.25 117.25 Radio Type Model EB450 ER450 TX Power (watts) 5.00 1.00 TX Power (dBW) 6.99 0.00 Effective Radiated Power (watts) 6.71 4.63 Effective Radiated Power (dBW) 8.27 6.66 RX Sensitivity Level (uv) 0.71 1.26 RX Sensitivity Level (dBW) -140.00 -135.00 RX Signal (uv) 9.70 21.70 RX Signal (dBW) -117.25 -110.26 RX Field Strength (uv/m) 95.74 115.23 Fade Margin (dB) 22.75 24.74 Raleigh Service Probability (%) 99.470 99.665 goodpath.pl3 Major Repeater Site Field Site Elevation (m) 756.69 309.67 Latitude 031 04 37.49 S 030 56 24.00 S Longitude 150 57 26.34 E 150 38 48.00 E Azimuth 297.05 117.21 Antenna Type ANT450/6OM ANT450/9AL Antenna Height (m) 40.00 5.00 Antenna Gain (dBi) 8.15 11.15 Antenna Gain (dBd) 6.00 9.00 TX Line Type LDF4-50 LDF4-50 TX Line Length (m) 40.00 5.00 TX Line Unit Loss (dB/100 m) 6.79 6.79 TX Line Loss (dB) 2.72 0.34 Connector Loss (dB) 2.00 2.00 Frequency (MHz) 450.00 Path Length (km) 33.33 Free Space Loss (dB) 115.99 Diffraction Loss (dB) 0.00 Net Path Loss (dB) 103.75 103.75 Radio Type Model EB450 ER450 TX Power (watts) 5.00 1.00 TX Power (dBW) 6.99 0.00 Effective Radiated Power (watts) 6.71 4.63 Effective Radiated Power (dBW) 8.27 6.66 RX Sensitivity Level (uv) 0.71 1.26 RX Sensitivity Level (dBW) -140.00 -135.00 RX Signal (uv) 45.93 102.70 RX Signal (dBW) -103.75 -96.76 RX Field Strength (uv/m) 453.14 545.42 Fade Margin (dB) 36.25 38.24 Raleigh Service Probability (%) 99.976 99.985
Page 13E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Part D  System Planning and DesignEffect of Earth Curvature on Long PathsThis path requires greater mast height to offset the earth curvatureexperienced at such a distance (73km). longpath.pl3 Repeater Site Far Field Site Elevation (m) 221.26 75.58 Latitude 032 01 21.63 S 032 33 00.00 S Longitude 142 15 19.26 E 141 47 00.00 E Azimuth 217.12 37.37 Antenna Type ANT450/6OM ANT450/9AL Antenna Height (m) 40.00 5.00 Antenna Gain (dBi) 8.15 11.15 Antenna Gain (dBd) 6.00 9.00 TX Line Type LDF4-50 LDF4-50 TX Line Length (m) 40.00 5.00 6.79 6.79 TX Line Loss (dB) 2.72 0.34 Connector Loss (dB) 2.00 2.00 Frequency (MHz) 450.00 Path Length (km) 73.46 Free Space Loss (dB) 122.85 Diffraction Loss (dB) 22.94 Net Path Loss (dB) 133.55 133.55 Radio Type Model EB450 ER450 TX Power (watts) 5.00 1.00 TX Power (dBW) 6.99 0.00 Effective Radiated Power (watts) 6.72 4.64 Effective Radiated Power (dBW) 8.27 6.66 RX Sensitivity Level (uv) 0.71 1.26 RX Sensitivity Level (dBW) -140.00 -135.00 RX Signal (uv) 1.49 3.32 RX Signal (dBW) -133.55 -126.56 RX Field Strength (uv/m) 14.65 17.64 Fade Margin (dB) 6.45 8.44 Raleigh Service Probability (%) 79.735 86.656
Page 14E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Part D  System Planning and Design Antenna GainBy compressing the transmission energy into a disc or beam, theantenna provides more energy (a stronger signal) in that direction,and thus is said to have a performance “gain” over a basic omniantenna. Gain is usually expressed in dBd, which is referenced toa standard folded dipole. Gain can also be expressed in dBi, whichis referenced to a theoretical “isotropic” radiator. Either way, if youintend to send and receive signals from a single direction, there isadvantage in using a directional antenna - both due to theincreased signal in the wanted direction, and the relativelydecreased signal in the unwanted direction (i.e. “interferencerejection” properties).Tuning the AntennaMany antennas are manufactured for use over a wide frequencyrange. Typical fixed use antennas such as folded dipoles and yagisare generally supplied with the quoted gain available over theentire specified band range, and do not require tuning. Co-linearantennas are normally built to a specific frequency specified whenordering.With mobile “whip” type antennas, it is sometimes necessary to“tune” the antenna for the best performance on the requiredfrequency. This is usually done by trimming an antenna elementwhilst measuring VSWR, or simply trimming to a manufacturersupplied chart showing length vs frequency. These antennas wouldnormally be supplied with the tuning information provided.Antenna PlacementWhen mounting the antenna, it is necessary to consider thefollowing criteria:The mounting structure will need to be solid enough to withstandadditional loading on the antenna mount due to extreme wind, iceor snow (and in some cases large birds).For omni directional antennas, it is necessary to consider the effectof the mounting structure (tower mast or building) on the radiationpattern. Close in structures, particularly steel structures, can alterthe radiation pattern of the antenna. Where possible, omniantennas should always be mounted on the top of the mast or poleto minimise this effect. If this is not possible, mount the antenna ona horizontal outrigger to get it at least 1-2m away from thestructure. When mounting on buildings, a small mast or pole (2-4m)can significantly improve the radiation pattern by providingclearance from the building structure.For directional antennas, it is generally only necessary to considerthe structure in relation to the forward radiation pattern of theantenna, unless the structure is metallic, and of a solid nature. Inthis case it is also prudent to position the antenna as far away fromthe structure as is practical. With directional antennas, it is alsonecessary to ensure that the antenna cannot move in such a waythat the directional beamwidth will be affected. For long yagiantennas, it is often necessary to instal a fibreglass strut tostablilise the antenna under windy conditions.Alignment of Directional AntennasThis is generally performed by altering the alignment of theantenna whilst measuring the received signal strength. If the signalis weak, it may be necessary to pre-align the antenna using acompass, GPS, or visual or map guidance in order to “find” thewanted signal. Yagi antennas have a number of lower gain “lobes”centred around the primary lobe. When aligning for best signalstrength, it is important to scan the antenna through at least 90degrees, to ensure that the centre (strongest) lobe is identified.When aligning a directional antenna, avoid placing your hands orbody in the vicinity of the radiating element or the forward beampattern, as this will affect the performance of the antenna.Selecting AntennasThere are basically two types of antennas – omni directional, anddirectional.Omni directional antennas are designed to radiate signal in a 360degrees segment around the antenna. Basic short range antennassuch as folded dipoles and ground independent whips are used toradiate the signal in a “ball” shaped pattern. High gain omniantennas such as the “co-linear” compress the sphere of energyinto the horizontal plane, providing a relatively flat “disc” shapedpattern which goes further because all of the energy is radiated inthe horizontal plane.Directional antennas are designed to concentrate the signal into“beam” of energy for transmission in a single direction (ie for point-to-point or remote to base applications).Beamwidths vary according to the antenna type, and so can beselected to suit design requirements. The most common UHFdirectional antenna is the yagi, which offers useable beam widthsof 30-50 degrees. Even higher “gain” is available using parabolic“dish” type antennas such as gridpacks.
Page 15E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Part D  System Planning and DesignCommon Cable Types Loss per meter Loss per 10m@ 450MHz @ 450MHzRG58C/U 0.4426dB 4.4dBRG213/U 0.1639dB 1.6dBFSJ1-50 (¼” superflex) 0.1475dB 1.5dBLDF4-50 (1/2” heliax) 0.0525dB 0.52dBLDF5-50 (7/8” heliax) 0.0262dB 0.3dBData ConnectivityThe V24 StandardThe E Series radio modems provide two asynchronous V24compliant RS232 ports for connection to serial data devices.There are two types of RS232 interfaces – DTE and DCE.DTE stands for data terminal equipment and is generally applied toany intelligent device that has a need to communicate to anotherdevice via RS232. For example: P.C. Comm ports are always DTE,as are most PLC and RTU serial ports.DCE stands for data communication equipment and is generallyapplied to a device used for sending data over some medium(wires, radio, fibre etc), i.e. any MODEM.The standard interface between a DTE and DCE device (using thesame connector type) is a straight through cable (ie each pinconnects to the same numbered corresponding pin at the other endof the cable).The “V24” definition originally specified the DB25 connectorstandard, but this has been complicated by the emergence of theDB9 (pseudo) standard for asynch devices, and this connectorstandard has different pin assignments.The wiring standard is “unbalanced”, and provides for three basicdata transfer wires (TXD, RXD, and SG – signal ground).Hardware HandshakingHardware handshake lines are also employed to provide flowcontrol, however (in the telemetry industry) many devices do notalways support all (or any) flow control lines.For this reason, the E Series modems can be configured for fullhardware flow control, or no flow control at all (simple 3 wireinterface).Note: that when connecting devices together with differinghandshake implementations, it is sometimes necessary to “loop”handshake pins in order to fool the devices handshakingrequirements.In telemetry applications (particularly where port speeds can be setto the same rate as the radio systems over-air rate) then flowcontrol, and therefore handshaking, is usually NOT required. Itfollows that any devices that CAN be configured for “no flowcontrol” should be used in this mode to simplify cablingrequirements.Handshaking lines can generally be looped as follows:DTE (terminal) – loop RTS to CTS, and DTR to DSR and DCE.DCE (modem) - loop DSR to DTR and RTS (note-not required forE Series modem when set for no handshaking).RF Feeders and ProtectionThe antenna is connected to the radio modem by way of an RFfeeder. In choosing the feeder type, one must compromisebetween the loss caused by the feeder, and the cost, flexibility, andbulk of lower loss feeders. To do this, it is often prudent to performpath analysis first, in order to determine how much “spare” signalcan be allowed to be lost in the feeder. The feeder is also a criticalpart of the lightning protection system.All elevated antennas may be exposed to induced or directlightning strikes, and correct grounding of the feeder and mast arean essential part of this process. Gas discharge lightning arrestersshould also be fitted to any site that stands elevated or alone,particularly in rural areas.
Page 16E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Part D  System Planning and DesignCable Wiring Diagrams
Page 17E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Part D  System Planning and DesignRS232 Connector Pin outs (DCE)Port A and B, Female DB9Cable Wiring Diagrams
Page 18E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Part D  System Planning and DesignPower Supply and EnvironmentalConsiderationsGeneralWhen mounting the equipment, consideration should be given tothe environmental aspects of the site. The cabinet should bepositioned so that it is shaded from hot afternoon sun, or icy coldwind. Whilst the radios are designed for harsh temperatureextremes, they will give a longer service life if operated in a morestable temperature environment. In an industrial environment, theradio modems should be isolated from excessive vibration, whichcan destroy electronic components, joints, and crystals.The cabinet should provide full protection from moisture, dust,corrosive atmospheres, and other aspects such as ants and smallvermin (who’s residues can be corrosive or conductive). The radiomodem will radiate heat from the in-built heatsink, and the higherthe transmitter duty cycle, the more heat will be radiated from theheatsink. Ensure there is sufficient ventilation in the form ofpassive or forced air circulation to ensure that the radio is able tomaintain quoted temperature limits.Power SupplyThe power supply should provide a clean, filtered DC source. Theradio modem is designed and calibrated to operate from a13.8VDC regulated supply, but will operate from 10-15 volts(filtered) DC.The power supply must be able to supply sufficient current toprovide clean filtered DC under the full current conditions of theradio modem (ie when transmitting full RF power). The currentrequirement is typically 120mA (230mA for EB450) in receivemode, and will vary in transmit mode according to RF output powerlevel (typically 0.5-1.5 amps, 1.3-2.5 amps for EB450).Solar ApplicationsIn solar or battery-backed installations, a battery management unitshould be fitted to cut off power to the radio when battery levels fallbelow the minimum voltage specification of the radio. In solarapplications, a solar regulation unit MUST ALSO be fitted to ensurethat the radio (and battery) is protected from excessive voltageunder full sun conditions.When calculating solar and battery capacity requirements, theconstant current consumption will be approximately equal to thetransmit current multiplied by the duty cycle of the transmitter, plusthe receive current multiplied by the (remaining) duty cycle of thereceiver.The Tx/Rx duty cycle will be entirely dependent on the amount ofdata being transmitted by the radio modem, unless the device hasbeen configured for continuous transmit, in which case theconstant current consumption will be equal to the transmit currentonly (at 100% duty cycle).Site EarthingThe radio must not be allowed to provide a ground path fromchassis to (DB9) signal ground or (-) battery ground. Ensure thatthe chassis mounting plate, power supply (-) earth, RTU terminaldevice, and lightning arrester (if fitted), are all securely earthed to acommon ground point to which an earth stake is attached. Pleasepay particular attention to 24VDC PLC systems using DC-DCconverters to supply 13.8Vdc.Caution: There is NO internal replaceable fuse, andtherefore the radio modem MUST be externally fused withthe fuse holder provided (ER450: 3 amp slo-blow fuse,EB450: 5 amp fast-blow fuse).
Page 19E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Physical Dimensions of the Remote Data Radio - ER450
Page 20E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Physical Dimensions of the Base Station - EB450
Page 21E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Physical Dimensions of the Hot Standby Base Station - EH450
Page 22E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Part E  Getting Started - ER450Part E  Getting StartedER450 Quick Start GuideIntroductionWelcome to the ER450 Quick Start Guide. This guide providesstep-by-step instructions, with simple explanations to get you up-and-running.Mounting and EnvironmentalConsiderationsThe ER450 radio comes complete with a mounting cradle and isattached to a panel or tray by means of screws or bolts, using the holeslots provided.Note: In high power or high temperature applications, it is desirable tomount the radio with the heatsink uppermost to allow ventalation forthe heatsink.The radio should be mounted in a clean and dry location, protectedfrom water, excessive dust, corrosive fumes, extremes oftemperature and direct sunlight. Please allow sufficient passive oractive ventilation to allow the radio modem’s heatsink to operateefficiently.Typical Radio Setup
Page 23E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Part E  Getting Started - ER450ER450 Connections LayoutConnecting Antennas and RF FeedersThe RF antenna system should be installed in accordance with themanufacturers notes.The RF connector used on the E Series radios are N Type femaleconnectors. Always use good quality low loss feeder cable,selected according to the length of the cable run. Ensure allexternal connections are waterproofed using amalgamating tape.Preset directional antennas in the required direction using acompass, GPS, or visual alignment and ensure correct polarisation(vertical or horizontal).Communications PortsSystem Port  RJ45The System Port (available front and rear on EB/EH450) is a multi-function interface used for:• Programming / Configuration of the radio• Remote Diagnostics connectionsTo access these functions use the standard E Series System Cableassembly (RJ45 Cable and RJ45 to DB9 Adaptor).System Port pinout assignments:Pin 1 System port data out (RS232)Pin 2 System port data in (RS232)Pin 3 Not usedPin 4 ShutdownPin 5 Not usedPin 6 Not usedPin 7 GroundPin 8 External PTTSpecial user pinouts:• Shutdown (Pin 4) - Active low for power save function• External PTT (Pin 8) - Provides a manual PTT overridefacility for enabling the transmitter. For testing this can beactivated by connecting PTT (Pin 8 ) to Gnd (Pin 7).
Page 24E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Part E  Getting Started - ER450User Interfaces  Ports A & BEach user port (A & B) is wired as a RS232 DCE, configurable for nohandshaking (3-wire) interface, or for hardware or software (X-on/X-off)flow control. In most systems flow control is not required, in whichcase only 3 wires need to be connected between the radio and theapplication device.Typical pins used:• Pin 2 (RxD) - data output from the radio modem,• Pin 3 (TxD) - data input to the radio modem,• Pin 5 (SG) - signal ground.See Part D – System Planning and Design - Data Connectivity, forfurther details of other cable configurations.RS232 Connector Pin outs (DCE)Port A and B, Female DB9Activating the TransmitterIn most systems, the transmitter by default is controlledautomatically by the radio when it has data to transmit.In some systems, such as full duplex point-to-point links or fullduplex point-to-multipoint base stations, it is desirable to run thetransmitter all the time (hot keyed).Two mechanisms are provided to do this:• the radio modem can be configured to transmit continuouslywhenever powered, or• the radio modem can be configured to transmit whenever anexternal RTS signal (Pin 7) is applied to one (or either) userports. (To simulate an external RTS input, loop pins 6 to 7).To operate in these modes, the radio must be configured via theprogramming software.Caution: When the radio is configured to transmitcontinuously, ensure an RF load is present BEFOREapplying power to the unit.
Page 25E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Part E  Getting Started- ER450Power Supply RequirementsThe E Series radio modem is designed and calibrated to operate froma filtered 13.8Vdc regulated supply, but will operate from a 10-16Vdc(11-16Vdc for EB450 & EH450) range.The current requirement is typically 120mA (230mA for EB450) inreceive mode, and will vary in transmit mode according to RFoutput power level (typically: ER450 0.5-1.5 amps, EB450 1.3-2.5amps, EH450 2-3.2 amps).Caution: There is NO internal replaceable fuse, and thereforethe radio modem MUST be externally fused with the fuseholder provided (ER450: 3 amp slo-blow fuse, EB450: 5amp fast-blow fuse).The radio is designed to self protect, and will blow the externalfuse if the voltage exceeds 16Vdc, or if reverse polarity is applied.The radio modem can also be damaged if there is any potentialdifference between the chassis-ground, RS232 signal ground,power (-) input, or antenna coaxial shield. Before connecting anywiring, ensure all components are earthed to a common groundpoint (please pay particular attention to 24V PLC power systemswhere converters are used).Connect the antenna and RS 232 plugs BEFORE applying powerto the unit.Lastly, before inserting the power plug, please re-check that thepolarity and voltage on the power plug is correct using amultimeter.TVIEW+ Management SuiteRadio ConfigurationThis TVIEW+ Management Suite allows a number of featuresincluding: Configuration (Local - serial, or Remote - over-the-air),Remote Diagnostics Facilities and Firmware Upgrades.The configuration wizard can be used to provide Quick Startgeneric templates for the types of systems architecture you wish toemploy.Example: Local configuration session –1 Attach the programming cable from the PC to the SystemPort of the radio2 Launch TVIEW+ & Select “Programmer”3 Select “Read” the radio4 Change the configuration as required5 Select “Write” the parameters back to the radioRefer to Parts I & J – TVIEW+ Management Suite for detailedoperation of advanced features.
Page 26E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Part E  Getting Started- ER450Optimising the Antenna for VSWR andbest RX signalOnce the unit is operational, it is important to optimise the antennatuning.In the case of a directional antenna, it will be necessary to align theantenna for the best received signal.This can be done by using the (0-5Vdc) output on Pin 9 of Port B toindicate signal strength (RSSI). This voltage can be converted todBm using the chart below.VSWR testing is achieved by activating the radio’s transmitterusing:a) An RTS loopb) A system port PTT plugSee Part G - Commissioning for further details.LED Indicators & Test OutputsRadio is PoweredIf all the LEDs are off, no power is reaching the radio modem.Successful power-up is indicated by the “PWR” LED indicating acontinuous (healthy) GREEN state. Note that this LED is turnedRED when the transmitter is active.Voltage ErrorIf the voltage is too high(>16Vdc) or too low(<10Vdc), an errormessage will be displayed on the staus LED’s by illuminating all fourLED’s RED.Hardware ErrorA hardware error is indicated on any one of the status LED’s byilluminating solid RED. In the case of a hardware error, the unit mustbe returned to the service point for repair. Record the result with theservice return information.LED LegendAnalog RSSI Output Characteristics - E Series Data Radio00.511.522.533.544.55-120-110-100-90-80-70-60-50-40RF Level (dBm)RSSI (DC Volts)
Page 27E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Part E  Getting Started- ER450Received Signal IndicatorThe “RX/SYNC” LED is used to indicate the state of the receiver.If the LED is off, no signal is being received.A RED indication shows that an RF carrier is being received, but nodata stream can be decoded. This will briefly happen at the very startof every valid received transmission or may indicate the presence ofinterference, or another user on the channel.A continuous GREEN indication shows that the modem is locked andsynchronised to the incoming signal, and has excellent Bit ErrorRate (BER). Any losses of synchronisation (BER errors) are shownas a visible RED flicker of the LED.Note: This might only be apparent on a PTMP slave when onlyreceiving.Verifying Operational HealthIt is possible to verify the operation of the radio modem using theindicators provided by the unit. The state of the transmitter andreceiver, and data flow can be interpreted by the indicator LEDs (seebelow).Note: Port A and Port B’s RxD and TxD will be Active on Data FlowData Flow breakout LEDsThere are also two LEDs to indicate data flow into and out of the twouser ports.Input data to be transmitted is shown as a RED flash, and receiveddata to be output to the port is shown as a GREEN flash.If data is alternately flowing in and out quickly, then the indicatorappears orange.Full Duplex – PTMP Master TxHalf Duplex – Master or Slave (Tx)Half Duplex – PTMP Slave RxHalf Duplex – Master or Slave (Rx)Full Duplex – PTP Master or SlaveLED Legend
Page 28E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Part E  Getting Started - EB450EB450 Quick Start GuideIntroductionWelcome to the Quick Start Guide for the EB450 Base / RepeaterData Radio. This guide provides step-by-step instructions, withsimple explanations to get you up-and-running.Mounting and EnvironmentalConsiderationsThe EB450 Base Station is housed in a 2RU 19” rack enclosure.The 4 mounting holes on the front panel should be used to securethe unit to the rack.The radio should be mounted in a clean and dry location, protectedfrom water, excessive dust, corrosive fumes, extremes oftemperature and direct sunlight. Please allow sufficient passive oractive ventilation to allow the radio modem’s heatsink to operateefficiently.All permanent connections are made at the rear of the unit. Thisincludes: Power, Antenna, Communications Ports, Digital I/O andSystem Port. The front panel has an additional System Portconnection point for easy access.Full Duplex ConsiderationsThe EB450 is designed for continuous full duplex transmission. Anautomatic thermostatically controlled fan will operate whenever theinternal temperature exceeds 50 degrees Celsius.External Duplexer ConsiderationsThe EB450 is normally supplied with seperate Tx and Rx ports forconnection to an external duplexing system.Depending on the frequency band of operation and the Tx/Rxfrequency split, internal band reject duplexers are available.
Page 29E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Part E  Getting Started - EB450Connecting Antennas and RF FeedersSee ER450 Quick Start GuideCommunications PortsSee ER450 Quick Start Guide SectionPower Supply and ProtectionSee ER450 Quick Start Guide SectionTVIEW+ Management Suite - RadioConfigurationSee ER450 Quick Start Guide SectionOptimising the Antenna for VSWR andbest RX signalSee ER450 Quick Start Guide SectionLED Indicators & Test outputsRadio is PoweredIf all the LEDs are off, no power is reaching the radio modem.Successful power-up is indicated by the “PWR” LED indicating acontinuous (healthy) GREEN state. Note that this LED is turnedRED when the transmitter is active.Typical Radio SetupLED Legend
Page 30E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Bar Graph IndicatorsThe bar graph indicators on the front panel provide variableinformation regarding the performance of the Base Station. Toenable / disable the bar graph display depress the Display ON /OFF button. The display will turn off automatically after 5 minutes.DC Supply:Indicates the supply input voltage at the exciter module. Typically13.8Vdc.Indication: <10Vdc no LED’s on, 10-10.9Vdc LED’s RED, 11-15.6Vdc All LED’s GREEN, >=15.7Vdc last LED RED.Tx Power:Indicates forward RF power output as measured at the TX antennaport. Typically +37dBm.Indication: <20dBm no LED’s on, 20-40.6dBm (11.5W) LED’sGREEN, >=40.7dBm last LED RED.Tx Drive:Indicates exciter drive level. Typically +20dBm.Indication: <10dBm no LED’s on, 10.0-25.9dBm LED’s GREEN,>=26.0dBm last LED RED.Rx Sig:Indicates receive signal strength. Typically -85 to -65dBm.Indication: <-120dBm no LED’s on, -120 to -110.1dBm LED’s RED,>=-110dBm LED’s GREEN.RxFreq. Offset:Indicates offset of receiver AFC - useful in determining frequencydrift. Typically 0kHz.Indication: Single GREEN LED to indicate current value, <-3.6kHzor >+3.6kHz LED is RED. No signal, all LED’s OFF. Note: 5 secondpeak hold circuitry.Part E  Getting Started - EB450Test ModeThe Bar Graph indicators have a Test Mode, which cycles all LED’sfor correct operation (before returning to their normal operation). Toactivate this mode, simply depress the ON / OFF button whileapplying power to the unit.Voltage ErrorIf the voltage is too high(>16Vdc) or too low(<10Vdc), an errormessage will be displayed on the status LED’s by illuminating all four(4) LED’s RED.Hardware ErrorA hardware error is indicated on any one of the status LED’s builluminating solid RED. In the case of a hardware error, the unit mustbe returned to the service point for repair. Record the result with theservice return information.Received Signal IndicatorThe “RX/SYNC” LED indicates the state of the receiver.If the LED is off, no signal is being received.A RED indication shows that an RF carrier is being received, but nodata stream can be decoded. This will briefly happen at the very startof every valid received transmission or may indicate the presence ofinterference, or another user on the channel.A continuous GREEN indication shows that the modem is locked andsynchronised to the incoming signal, and has excellent Bit ErrorRate (BER). Any losses of synchronisation (BER errors) are shownas a visible RED flicker of the LED.Note: This might only be apparent on a PTMP slave when onlyreceiving.Data Flow breakout LEDsThere are also two LEDs to indicate data flow into and out of thetwo user ports.Input data to be transmitted is shown as a RED flash, and receiveddata to be output to the port is shown as a GREEN flash.If data is aternately flowing in and out quickly, then the indicatorappears orange.
Page 31E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.EH450 Quick Start GuideIntroductionWelcome to the Quick Start Guide for the EH450 Hot Standby Base /Repeater Station. This section provides additional step-by-stepinstructions to install, commission and operate the EH450 HotStandby Base Station. This document should be read in conjunctionwith the EB450 Base Station Quick Start Guide.The EH450 is a fully redundant, hot standby digital data radio base /repeater station providing automatic changeover facilities.The EH450 is designed as a modular solution, comprising 2 identicalEB450 base station units (standard) linked to a central, fail-safemonitoring and change-over controller (Hot Standby Controller). Eitherbase station may be taken out for maintenance without the need forany system down time. The automatic change-over is triggered by outof tolerance (alarm) conditions based on either RF and/or user datathroughput paramaters.Part E  Getting Started - EH450Features and Benefits• Individual and identical base stations with separate control logicchangeover panel• Modules are hot swapable without user downtime• Flexible antenna options – single, separate Tx & Rx, two Txand two Rx• Increased sensitivity with receiver pre-amplifier• Both on-line and off-line units monitored regardless of activestatus• External input for higher stability 10MHz reference – GPSderived• Also refer to the common Features and Benefits list of the ESeries Data RadioBase / Repeater UnitHot Standby Controller UnitBase / Repeater UnitEH450 Hot Standby Base / Repeater UnitNOTE: RF connectors not used or ETSI version Rear View
Page 32E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Operational DescriptionThe Hot Standby Controller (HSC) unit is a 1RU rack mountedmodule that interfaces to two physically separate base stations (each2RU rack mounted modules) via a number of RF and data cables.Both base stations are operating simultaneously and both units areconstantly receiving signals, however only data from one basestation, the “online” base station is directed to the user equipment. Theonline base station is the only base station transmitting at any time.The Hot Standby Controller has the following functions:• Diplex the transmit and receive paths (Assuming internalduplexer fitted), TX Only.• Amplify and split the incoming signal two ways so both basestations receive at once.• Monitor status reports from both base stations to identify faultsand swap over the online base station if required.• Switch the antenna via internal coaxial relay duplexer to theonline base station transmitter and inhibit the offline base stationfrom transmitting.• Switch the User A and B data ports through to the online basestation.An optocoupler based switch in the base station controller directs datato and from ports A and B on the rear panel directly to ports A and B onthe on-line base station without any involvement from the Hot Standbycontroller microcontrollers (apart from selecting the on-line base). Thisprovides protection of the system from failure of the microcontroller.As well as ports A and B, each base has a system port. The systemport of each base station is interfaced to the microcontroller on the HotStandby controller. This allows the microcontroller in charge ofselecting the base station to receive diagnostic messages from eachbase station to decide their health.The base station has it’s own system port on the rear panel and this isinterfaced to the Hot Standby Contruller Module. The HSC will routediagnostics at the rear panel system port to and from the system portsof the base stations.Mounting and EnvironmentalConsiderationsThe EH450 Hot Standby Base Station is housed as a 5RU 19” rackmounted set, encompassing 2 x 2RU Base Station units and 1 x 1RUHot Standby Controller unit. The mounting holes on the front panelsshould be used to secure the units to the rack.The unit should be mounted in a clean and dry location, protected fromwater, excessive dust, corrosive fumes, extremes of temperature anddirect sunlight. Please allow sufficient passive or active ventilation toallow the radio modem’s heatsink to operate efficiently.All permanent connections are made at the rear of the unit. Thisincludes: Power, Antenna, Communications Ports, Digital I/O andSystem Port. The front panel has an additional System Portconnection point for easy access.The Base Station front panel system ports must not be used while inthis config.Part E  Getting Started - EH450
Page 33E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Communications PortsThe A & B Data Ports and System Ports of each Base Stationconnect directly to the Hot Standby Controller units correspondingports with the cables provided. Ensure all clamping screws on theData Port cables are firmly secured and the System Port cables areclipped in correctly. See figure below for further details.Note: Only the front or rear User System Port can be used at anyone time on the HSC.Power Supply and ProtectionThe EH450 has facilities for dual power supplies to provide for aredundant system. A separate power supply should be used for eachof the Base Station units. The Hot Standby Controller unit hasconnections for dual power supplies and it is recommended that thepower supplies from each of the Base Stations also be used to powerthe Hot Standby Controller unit. See Figure below for further details.See ER450 Quick Start Guide Section for detailed wiring information.The Hot Standby Controller units A & B Data Ports connect directly toyou application device and the System Port connects directly to yourlocal PC. See ER450 Quick Start Guide Section for further details.Part E  Getting Started - EH450Note: RF Connectors not used for ETSI versionNote: RF Connectors not used for ETSI version
Page 34E Series Data Radio – User Manual© Copyright 2002 Trio DataCom Pty. Ltd.Connecting Antennas and RF FeedersThere are 3 primary antenna connection options. All connectors usedare standard N Type sockets. See figures below for further details.See ER450 Quick Start Guide for detailed wiring information.Part E  Getting Started - EH450
Page 35E Series Data Radio – User Manual © Copyright 2002 Trio DataCom Pty. Ltd.Front Panel OperationSwitchesSelect SwitchThe 3 position switch (1 / Auto / 2) on the front panel provides thefollowing functionality:• Position 1: base station 1 is forced into operation• Position Auto: changeover hardware will select the online basestation• Position 2: base station 2 is forced into operationThe select switch is also used to identify the target base station forconfiguration programming.Adjacent to the select switch are two LEDs: These LEDs indicate thecurrent active base station.Select LED’s•Green - Auto Mode•Red - Remote Force•Amber - Local Force2 Green Firmware Download2 Amber Test Mode2 Red Fatal Error - refer user manualReset SwitchThis is a momentary close switch which when depressed will reset allLED alarm indications.System PortThere are two system port connection points, one on the rear paneland one on the front panel. Both have the same functionality and canbe used for local diagnostics, firmware front panel downloads and hotstandby controller testing. To access the system port use thediagnostic/programming cable supplied.Note: Wnen connection is made to front panel system rear systemport is disabled.Alarm Status LEDsThere are 10 alarm LEDs on the fron panel, five for base 1 and five forbase 2. These LEDs provide a general indication of base stationstatus. More detailed base station status information is available byusing the diagnostic utility software.The indicated alarms for each base station are:Freq. => Frequency ErrorRxSig => Receive Signal (RF) ErrorData => Receive Data ErrorTxPower => Transmit Power (RF) ErrorSupply => DC Voltage ErrorThe status of each alarm is represented as follows:Green => No ErrorRed => Current (active) Error conditionAmber => Recovered Error conditionAny active or recovered error LEDs will turn to green after the resetalarms switch has been pushed or remotely reset.Part E  Getting Started - EH450

Navigation menu