Sebury Technology W3-H ACCESS CONTROL User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1657028
Application ID	+a+ymrmzN2jO5+tgzNWkvQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	36.55kB (456883 bits)
Date Submitted	2012-03-15 00:00:00
Date Available	2012-03-15 00:00:00
Creation Date	2010-03-15 05:36:15
Producing Software	Corel PDF Engine Version 14.0.0.653
Document Lastmod	0000-00-00 00:00:00
Document Title	W3-H 英文说明书印刷版修改12.cdr
Document Creator	CorelDRAW
Document Author:	Administrator

11.2 Relay Setting (Pulse mode,Toggle mode)
To change a PIN in card and PIN
mode (Method 1)
Note that this is done outside
programming mode so the user can
undertake this themselves
* Read Card Old PIN # New PIN # New PIN #
Pulse mode(Factory default)
* ID number # Old PIN # New PIN #
New PIN #
Pink
To disable the red LED
To enable the red LED(Factory default)
4 1-99 #
The door relay time is between 1-99 seconds,
the factory default setting is 5 seconds.
Toggle mode
7 8 #
7 9 #
To set keypad tone
4 0 #
GND
V+
Read Valid Card or Master Code #
To reset the Door Open Too Long warning
V+
GND
Close the door or Read Valid Card or Master Code #
Controller
11.3 Door Detection, Alarm, Sound and Light Settings
2 User ID #
To set a card user in card mode ( 3
W3-H Quick Reference Programming Guide
To enter the programming mode
* Master code #
888888 is the default factory master code
To exit from the programming mode
Note that to undertake the following programming the master user must be logged in
0 # )
The operating is the same as adding and deleting
a card user in 3 2 #
To Add and Delete a card user
To delete All users
To delete ALL users
Note that this is a dangerous option
so use with care
2 0000 #
0 New code # New code #
The master code can be 6 digits long
To change the master code
To add a PIN user
1 Read Card #
Cards can be added continuously without
exiting from programming mode
To add a Card user
To delete a PIN or a Card user
User ID number # for a PIN user or
Read Card # for a card user
To unlock the door
To add Card User by Manager Add
Card
Manager add card Read User card
Manager add card
Cards can be added continuously
To delete Card User by Manager
Delete Card
Manager delete card Read User Card
Manager delete card
Cards can be deleted continuously
To unlock the door
For a PIN user
For a card user
To unlock the door for a PIN user
Enter the PIN then press #
To unlock the door for a card user
Present the card
For a card and PIN user
Enter the PIN then press #
Read card
Read card then enter PIN #
OPEN
Brown
D_IN
Door Forced Open warning. When used with an optional magnetic contact or built-in
magnetic contact of the lock, if the door is open by force , or if the door is opened after
20 seconds of the electro-mechanical lock not closed properly, the inside buzzer and
alarm output will both operate. The Alarm Output time is adjustable between 0-3
minutes with the default being 1 minute.
To disable door open detection
6 0 # (Factory default )
To enable door open detection
6 1 #
AC&DC
Blue
NO
Purple
COM
Orange
NC
To set the alarm output time (0-3
minutes). Factory default is 1 minute
9 0-3 #
Keypad Lockout & Alarm Output options. If there are 10 invalid cards or 10
incorrect PIN numbers in a 10 minute period either the keypad will lockout for 10
minutes or the alarm will operate for 10 minutes, depending on the option selected
below.
Normal status: No keypad lockout
7 0 # (Factory default)
or alarm
7 1 #
Alarm Output
7 2 #
To add a PIN user
(The ID number is any number between 2001-2010)
To delete a PIN user
1: Keypad Transmission
The Reader will transmit the PIN data when it receives the last key (#) press after PIN
code.
Format: PIN Code ( any 4-8 digits between 0000-99999999)
Example: PIN code:111111
Press 111111 #, then the output format will be: 0000111111
( Note: if press an invalid PIN (any 4-8 digits), the data will be also transmitted.)
To set Dur e ss card user
To add a card user
(The ID number is any number between 2001-2010)
2: Proximity Card Transmission
The Reader will transmit the card data when it reads the Card.
Format: Card Number
(Note: No matter the card is valid or invalid, the data will be transmitted)
14.2 W3-H operating as a Controller
In this mode the W3-H supports a Wiegand 26-37 bit input so an external Wiegand
device with a 26-37 bit output can be connected to the Wiegand input terminals on the
W3-H. Either an ID card reader (125KHz) or an IC card reader (13.56MHz) can be
connected to the W3-H. Cards are required to be added at the external reader, except
where an external HID reader is used, in this case cards can be added at either reader
or controller. See figure 2.
13. Wiegand Mode Setting
Special Power Supply
DC 12V /3A
GND
W3-H supports Wiegand 26-37, both input and output. It can be used as a reader or controller.
D0
D1
To set Wiegand format:
9 26-37 # (Default setting: Wiegand 26)
ALARM-
D_IN
14. Interconnecting Two Devices
AC&DC
AC&DC
NO
14.1 W3-H operating as a Wiegand Output Reader
Light and Sound Setting
7 4 #
7 5 #
To set keypad backlight
To disable keypad backlight
To enable keypad backlight(Factory default)
Keypad/Reader/Controller
Transmission Format:
OPEN
Keypad Lockout
W3-H Waterproof
W3-H
Note:
① User ID number must be any 4digits between 2001 - 2010
② Duress PIN/card must be unique, should be distinguished from common PIN and card
(When the Duress PIN/card is the same with common PIN and card, they will become invalid
in Duress, and worked as common user function)
Alarm output time
AC&DC
Black
Figure 1
There are 10 groups Duress PIN/card available. When input Duress PIN/card, the door
will open, at the same time, the output alarm operates.
To set Duress PIN user
To delete a card user
To set card users by Manager card
1 User ID number # PIN #
The ID number is any number between
1-2,000. The PIN is any 4-8 digits between
0000 - 99999999 with the exception of 1234
which is reserved. Users can be added
continuously without exiting programming
mode
ALARM-
Yellow
12. Duress User Settings
Door Open Detection
Door Open Too Long (DOTL) warning. When used with an optional magnetic contact
or built-in magnetic contact of the lock, if the door is opened normally, but not closed
after 1 minute, the inside buzzer will beep automatically to remind people to close the
door and continue for 1 minute before switching off automatically.
D1
Grey
Red
Power
To delete a Card and PIN user just
delete the card
D0
White
To remove the alarm
To reset the Door Forced Open warning
Toggle mode
To disable the keypad tone
To enable the keypad tone(Factory default)
GND
Green
D0
D1
Pulse mode
(Door relay time setting)
To change a PIN in card and PIN
mode (Method 2)
Note that this is done out side
programming mode so the user can
undertake this themselves
7 6 #
7 7 #
To set LED
COM
In this mode the W3-H supports a Wiegand 26-37 bit output so the Wiegand data lines
can be connected to any controller which supports a Wiegand 26-37 bit input.
See figure 1.
NC
Pink
Wiegand reader
Green
COM NO +12V GND OPEN
D0
White
D1
Exit button
Grey
GND
Yellow
Brown
NC
Fail-Secure lock
Fail-Secure lock
V+
Door detecting switch
Alarm
Red
Black
Blue
Purple
Orange
W3-H
Figure 2
.7.
.8.
Rubber Bungs
6*27mm, used for fixing
Self Tapping Screws
4*28mm, used for fixing
Diode
IN4004
Manager Card
Manager Add Card & Manager Delete Card
Please ensure that all the above contents are correct. If any are missing please notify
the supplier of the W3-H.
2. Description
The W3-H is a single door multifunction access control with HID card reader. It is
suitable for mounting either indoor or outdoor in harsh environments. It is housed in a
strong, sturdy and vandal proof zinc alloy electroplated case. The electronics are fully
potted so the W3-H is waterproof and conforms to IP68.
The W3-H supports up to 2,000 users in either a Card, 4-8 digits PIN, or a Card + PIN
option and additional 10 groups Duress PIN/Card. The built-in card reader supports HID
125KHz frequency cards/tags. The W3-H has many extra features including Duress
PIN/card, block enrollment, Wiegand 26-37 bits interface, and backlight keypad…etc.
These features make W3-H an ideal choice for door access not only for small shops and
domestic households but also for commercial and industrial applications such as
factories, warehouses, laboratories, banks and prisons.
3. Features
Waterproof, conforms to IP 68
Strong zinc alloy electroplated anti-vandal case
Full programming from the keypad
2,000 users, supports Card, PIN, Card + PIN
10 groups Duress PIN/Card
Card interface: HID 125KHz Card
Can be used as a standalone keypad, PIN length 4-8 digits
Pulse mode, Toggle mode
Wiegand 26-37 input & output
One programmable relay output, NO, NC, COM
Adjustable door output time, alarm time, door open time
Card block enrollment
.1.
NO
NC
COM
AC&DC
AC&DC
OPEN
D_IN
ALARM-
NC
AC&DC
NO
COM
D0
D1
GND
D0
J1
D1
Anti-demolition alarm
ALARMOPEN
D_IN
4. Specifications
Operating Voltage
User Capacity
12-24V DC or 1 2 -18V AC
2,000 (Additional10 groups Duress PIN/Card)
Keypad
12 keys: 3 X 4 digits
Card Type
HID 125KHz card
Card Reading Distance
3-6 cm
W3-H
PCB connect diagram
6. Wiring
AC&DC
NO
Colour
Function
Description
Green
D0
Wiegand Output D0
White
D1
Wiegand Output D1
Alarm -
Alarm Negative
OPEN
Request to Exit Button
COM
NC
Active Current
≥65mA
Grey
Idle Current
Lock Output Load
≥35mA
Yellow
Max 2A
Brown
Alarm Output Load
Max 20A
Red
12-24V DC or 12-18V AC
12-24V DC or 12-18V AC Regulated Power Input
Operating Temperature
-20-50
Black
12-24V DC or 12-18V AC
12-24V DC or 12-18V AC Regulated Power Input
Operating Humidity
10%-90% RH
Blue
NO
Relay NO
Environment
Adjustable Door Relay Time
Conforms to IP68
Purple
COM
Relay COM
Orange
Relay NC
Adjustable Alarm Time
NC
Wiegand Interface
0-3 minutes
Wiegand 26-37 input & output
Pink
GND
W3-H Negative
Wiring Connections
Electric Lock, Exit Button, DOTL, External Alarm
Dimensions
Net Weight
L128 X W82 X H28mm
600 g
Gross Weight
700 g
1-99 seconds
D-IN
GND
D1
OPEN
D_IN
AC&DC
AC&DC
NO
COM
NC
Alarm “ - ”
White
Grey
Power
Exit button
Operation successful
12-24V DC or
12-18V AC/3A
Operation failed
Enter into programming mode
In the programming mode
Yellow
Brown
Door
detecting switch
Red
Exit from the programming mode
Black
Open the door
Alarm
Purple
Power“+”
Electric bolt：
NC
Orange
W3-H
Electric strike：
NO
Lock
Power
DC 12V /3A
Green
Wiegand D0
White
Wiegand D1
Grey
Exit button
NO
+12V GND OPEN
Fail-secure lock
Yellow
Brown
COM
Door
detecting switch
Alarm“-”
Alarm
Purple
Orange
Special Power Supply
.3.
Bright
Bright
Bright
Short Ring
Alarm
To enter the programming mode
Notes:
Connect the negative pole of the lock to NC is for Fail safe lock.
Connect the negative pole of the lock to NO is for Fail-secure lock.
(This step must be done out of
programming mode)
To add a card user (Method 1)
This is a fastest way to add cards
using ID number auto generation
To add a card user (Method 2)
This is the optional way to add
cards using User ID Allocation.
In this method a User ID is allocated
to a card. Only one user ID can be
allocated to a single card
* ID number # Old PIN # New PIN #
New PIN #
1 Read Card
Cards can be added continuously without exiting
programming mode
ID number # Card #
To exit from the programming mode
Note that to undertake the following programming the master user must be logged in
To change the master code
0 New code # New code #
The master code is any 6 digits
Setting the working mode:
set valid card only users
set valid card and PIN users
set valid card or PIN users
3 0 # Entry by Card only
3 1 # Entry by Card and PIN together
3 2 # Entry by either Card or PIN (default)
To set a user in either card or PIN mode ( 3 2 # ) (Default setting)
Every time a valid tag/card or PIN is read/input in Pulse Mode, the relay will operate, for
the pre-set relay pulse time.
To add a PIN user
Every time a valid tag/card or PIN is read/input in Toggle Mode, the relay changes state,
which will not turn back until read card or input PIN again.
9. To Reset to Factory Default
Remarks: Reset to factory default, the user's information is still retained.
.4.
To delete a PIN user
To add a card user (Method 3)
Add a series cards users - Block
Enrollment
5 ID number # The 1st Card number #
Card quantity #
Note that cards must be consecutive, and card
quantity is between 1-2000
Maximum 2,000 cards can be enrolled at a
stretch within 2 minutes
To delete card user by card
2 Read Card
* Master code #
888888 is the default factory master code
The relay on board can operate in Pulse Mode (suitable for access control) or Toggle
Mode (suitable for arming/disarming alarms, switching lights, machines….etc)
To reset to factory default, power off, press * , hold it and power on, release it until hear
two beeps and the LED shines in orange, then read any two HID cards, the LED will turn
in red, means reset to factory default setting successfully. Of the two HID cards read, the
first one is Manager Add Card, the second one is Manager Delete Card.
Blue
Buzzer
Short Ring
Short Ring
Short Ring
3 Short Ring
Short Ring
Short Ring
11.1 User Settings
Black
Yellow Light
Bright
11. W3-H Detailed Programming Guide
Red
Green Light
Bright
Common Power Supply
The W3-H uses a LDR (light dependent resistor) as an anti tamper alarm. If the keypad
is removed from the cover then the tamper alarm will operate.
NC
To change the PIN of a PIN user
Red Light
Bright
Bright
Bright
Blue
7. Anti Tamper Alarm
Pink
W3-H
.2.
Power“+”
Green
Operation Status
Power on
Stand by
Press keypad
8. Relay operation (Pulse mode and Toggle mode)
ALARM-
Remove the back cover from the keypad using the supplied security screwdriver
Drill 4 holes on the wall for the screws and 1 hole for the cable
Fix the back cover firmly on the wall with 4 flat head screws
Thread the cable through the cable hole
Attach the keypad to the back cover
Door Contact
Connection Giagram
D0
5. Installation
AC&DC
Alarm
Pink
In4004
Screw Driver
J1
D0
D1
User Manual
GND
Digital Keypad W3-H
Remark
D_IN
AC&DC
Quantity
User Manual
.10.
10. Sound and Light Indication
ALARMOPEN
Name
With Manager Cards for adding or deleting card user easily
Backlight keypad
Built in light dependent resistor (LDR) for anti tamper
Built in buzzer
Red, Yellow and Green LED display the working status
12-24V DC or 12-18V AC
Two-year warranty
GND
1. Packing list
.9.
1 User ID number # PIN #
The ID number is any number between 12000. The PIN is any 4-8 digits between 0000
-99999999 with the exception of 1234 which
is reserved. Users can be added continuously
without exiting from programming mode as
follows:
1 User ID No 1 # PIN # User ID No 2 # PIN #
To delete a card user by user ID
This option can be used when a
user has lost their card
2 User ID #
To delete a card user by card number
2 Card number #
Users can be deleted
continuously without exiting
from programming mode
To set a card and PIN user in card and PIN mode ( 3 1 # )
To Add a card and PIN user
(The PIN is any 4-8 digits between
0000 - 99999999 with the
exception of 1234 which is
reserved)
Add the card as for a card user
Press * to exit from the programming mode
Then allocate the card a PIN as follows:
* Read Card 1234 # PIN # PIN #
2 User ID number #
Users can be deleted continuously without
exiting programming mode
.5.
Note users can be deleted
continuously without exiting
from programming mode
.6.
FCC WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
NOTE 1: Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-701
Creation Date--Text             : 
Producer                        : Corel PDF Engine Version 14.0.0.653
Mod Date--Text                  : 
Trapped                         : False
Format                          : application/pdf
Creator                         : Administrator
Title                           : W3-H 英文说明书印刷版修改12.cdr
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Creator Tool                    : CorelDRAW
Modify Date                     : 2012:03:15 15:57:09+08:00
Metadata Date                   : 2012:03:15 15:57:09+08:00
Document ID                     : uuid:b8e2d1ff-073c-46ed-b17a-db8715be5db4
Instance ID                     : uuid:984de416-a007-4b40-b6b8-8fef481c6c76
Page Count                      : 2
Create Date                     : D:20100315053615Z
Author                          : Administrator

EXIF Metadata provided by EXIF.tools