Secure Wireless GB319 Wireless Glass Break User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1482522
Application ID	ycZwEQrKidB+aszqVZTuow==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	21.21kB (265180 bits)
Date Submitted	2011-06-14 00:00:00
Date Available	2011-06-14 00:00:00
Creation Date	2011-06-13 13:28:45
Producing Software	Microsoft® Word 2010
Document Lastmod	2011-06-13 13:28:45
Document Title	User manual
Document Creator	Microsoft® Word 2010
Document Author:	JeffC

GLASS BREAK ENROLLMENT PROGRAMMING
For a detail programming guide, the instruction manual
should be consulted for that panel. The below guide
should only be used as a reference and not as a
replacement for using the programming instructions.
1.
2.
3.
4.
5.
6.
ENTER Panel Programming
SELECT Zone #
ENTER 6 Digit Id Number ( located on back
of unit)
ENTER Check sum (0-9 ; A-F) (located on
back on unit. Digit that follows “:” on the
Serial ID
ENTER Point “3” – for Glass Break
Push On/Off to Save
MOUNTING INSTRUCTIONS
1.
2.
3.
C - *2
D- * 3
E - *4
F-*5
Place the Glass Break Detector base on the
opposite wall or adjacent wall to the window
being protected (Distance 15 Ft maximum)
Attach to the wall using the supplied screws.
The test button should be facing the floor
When attaching the detector to the base, match
up to the alignment mark and turn clockwise
FUNCTIONAL TEST:
Push the test button for 2 seconds and then release. The
red LED will light while the button is pressed. The green
LED will blink once to indicate that the unit is in auto test
mode for 90 seconds.
1.
Alpha Chart
A - *0
B - *1
Use a glass break simulator to test the unit. LED
will flash green first then will flash LED to
indicate the glass breaking.
WIRELESS RANGE TEST:
319.5 MHz
Limited Life Time
(2) CR123A Panasonic
200-10008 Rev C
Glass Type and Thickness
Push and hold the test button for 5 seconds and release,
The LED will flash while the button is pressed. The green
LED will blink twice to indicate that the unit is in RF test
mode for 90 seconds.
FREQUENCY
WARRANTY
BATTERY
MANUAL PART #
1/8 in to ¼ in
1/8 in to ¼ in
1/8 to ¼ in
SW-NAP-GB
QNP-GB319
Plate
Tempered
Sealed Insulating
MODEL
FCC ID
TECHNICAL SUPPORT
Secure Wireless 866-908-Tech
www.mysecurewireless.com
FCC Compliance
This device complies with Part 15 FCC Rules. Operation
complies with the following 2 conditions (1) This device
may not cause harmful interference and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
INSTALLATION MANUAL
NAPCO COMPATIBLE
Glass Break
SW-NAP-GB
Remove the detector from the base by turning
counterclockwise. Replace with 2 CR123A batteries.
Observe the polarity when replacing the batteries
REPLACING THE BATTERY

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
Language                        : en-US
Tagged PDF                      : Yes
Author                          : JeffC
Creator                         : Microsoft® Word 2010
Create Date                     : 2011:06:13 13:28:45-07:00
Modify Date                     : 2011:06:13 13:28:45-07:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools