Sensitech T11006740 Temperature Monitor User Manual T83 54

Sensitech, INC. Temperature Monitor T83 54

Manual

RF TT4 Ambient 2K MonitorPN T11006740User ManualMillions Depend on the Integrity of Your Product.Sensitech’s Mission is to Ensure that Integrity.The Tools That Turn Information Into PowerFCC ID SRMT11006740TempTale®Manager Software Data Management Services TempTale®3 Monitor TempTale®4 Monitor RF Monitoring TagAlert™Monitor This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by Sensitech could void the user’s authority to operate the equipment.For more information, contact our client services group at 800-843-8367.Sensitech Inc. • 800 Cummings Center • Beverly, MA 01915 (978) 927-7033 • Fax (978) 921-2112 www.sensitech.com© 2005 All Rights Reserved.TempTale is a registered trademark and TagAlert is a trademark of Sensitech, Inc.800 Cummings Center, Beverly, MA 01915 T11006740
Starting a TempTale4 Monitor• Press and release the Start button.• The “Sunshine” icon appears in the upper left corner of the display. • The TempTale4 will begin to record data after the start-up delay has passed.Iniciar el TempTale4• Presione y libere el botón de inicio “Start”. • El icon del “Sol” aparecerá a la izquierda en la partesuperior de la pantalla. • El TempTale4 grabará despúes del tiempo de demura.Pantalla del Monitor:All TempTale®4 Monitors are programmed with a custom Start-up delay, measurement interval and alarm settings which have been pre-determined by the customer.To mark an important event (“Date Stamp”)• TempTale4 monitors provide an option to “Date Stamp” or mark an important event at any time during the monitoring cycle that will be visible when viewing the data. The mark is displayed as an arrow when viewing the graph and shown in italics when viewing the tabular data. • To mark a graph while the monitor is recording, press and release the “Start” button.• The “arrow” icon will appear temporarily in the lower left corner and the temperature history will appear on the display. Data appears as follows:Alarm1. Average temperature2. Highest temperature recorded3. Total time above high temperature limit4. Lowest temperature recorded5. Total time below low temperature limitWhen the TempTale4 is exposed to a temperature outside a pre-programmed limit and time threshold, an “Alarm bell” will appear in the lower right corner of the LCD display. Stopping a TempTale4 MonitorPress and hold (1 to 3 seconds) the Stop button until the “Stop sign” icon appears in the upper right corner of the LCD display. Stopped recordingLimits exceededMarked PointRecordingDisplayed Information Temperature dataPara marcar un evento importante (Estampa de fecha)• Los TempTale4 monitores tienen la opción de marcar un eventoimportante que occura durante el envio. Se puede ver esta marca cuandose baja la información. La marca aparecerá como una flecha en el grafícoy en italico en el tabular. • Para marcar el evento durante el envio, presione y libere el botón de inicio “Start”. • Una flecha aparecerá en la pantalla y la información de temperaturaaparecerá en el siguente orden:1. Temperatura promedio2. Temperatura grabada más alta3. Tiempo total por encima del límite alto4. Temperatura grabada más baja5. Tiempo total bajo del límite bajoAlarmaCuando el TempTale4 está fuera del límite bajo o alto del tiempo programado, un icon de alarma aparecerá a la derecha en la parte baja de la pantalla.Parar el TempTale4Presione y libere (1 a 3 segundos) el botón de parar “Stop” hasta que el icon de “Stop” aparezca a la derecha en la parte superior de la pantalla.ParadoAlarmaMarca de eventoIniciadoInformación de temperaturaLos monitores de TempTale®4 están programado con uno tiempo de demura, intervalo y limites de temperatura y tiempo que fueron requieridopor el cliente.

Navigation menu